Wacker Neuson LTW20Z3 Manuel utilisateur

Operator’s Manual

Light Tower, Wide Body

LTW 20Z-1

LTW 20Z-3

Notice d’Emploi

Tour d’éclairage, corps large

5000187567 05 1111

5000187567

EN / FR

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000187543 05 1111

Foreword

wc_tx001055gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines covered in this Manual

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Machine Item Number

LTW 20Z-1 0620375, 0620842

LTW 20Z-3 0620376, 0620843

Foreword

4 wc_tx001055gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

LTW 20Z Table of Contents

wc_bo5000187543_05TOC.fm 5

Foreword 3

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury, dam-

age to the equipment, or improper service. ....................................................... 9

1.3 Machine Description and Intended Use ............................................... 9

1.4 Safety Guidelines for Operating the Machine ..................................... 11

1.5 Lamp Safety ....................................................................................... 12

1.6 Operator Safety while Using Internal Combustion Engines ............... 13

1.7 Towing Safety ..................................................................................... 14

1.8 Service Safety .................................................................................... 15

2 Labels 17

2.1 Label Locations .................................................................................. 17

2.2 Label Meanings .................................................................................. 19

3 Operation 32

3.1 Preparing the Machine for First Use ................................................... 32

3.2 Preparing Trailer for Towing or Lifting ................................................ 33

3.3 Locating the Trailer ............................................................................. 34

3.4 Ground Connection ............................................................................ 34

3.5 Leveling Trailer ................................................................................... 35

3.6 Refueling the Machine ........................................................................ 36

3.7 Adjusting the Lights ............................................................................ 37

3.8 Control Panel (Manual Winch System) .............................................. 38

3.9 Raising the Tower (Manual Winch System) ....................................... 39

3.10 Lowering the Tower (Manual Winch System) .................................... 42

3.11 Control Panel (Power Winch System) ................................................ 44

3.12 Raising the Tower (Power Winch System) ......................................... 45

3.13 Lowering the Tower (Power Winch System) ..................................... 48

3.14 Manually Starting the Machine ........................................................... 50

3.15 Stopping the Machine ......................................................................... 51

3.16 Auto Mode (Remote Run) .................................................................. 51

3.17 Troubleshooting Automatic Shutdown ................................................ 52

3.18 Generator Derating ............................................................................. 53

3.19 Receptacle Panel ............................................................................... 54

3.20 Load Balancing ................................................................................... 56

Table of Contents LTW 20Z

6 wc_bo5000187543_05TOC.fm

3.21 Electronic Governor .............................................................................56

3.22 Emergency Stop Switch ......................................................................57

4 Maintenance 58

4.1 Periodic Maintenance Schedule ..........................................................58

4.2 Installing / Removing Light Fixtures ....................................................60

4.3 Removing / Replacing Lamps .............................................................61

4.4 Performing Daily Inspection ................................................................62

4.5 Checking Engine Coolant ....................................................................63

4.6 Replacing Air Cleaner .........................................................................64

4.7 Changing Engine Oil ...........................................................................65

4.8 Maintaining the Fuel/Water Separator .................................................67

4.9 Maintaining the Trailer .........................................................................67

4.10 Long-Term Storage .............................................................................68

4.11 Troubleshooting ...................................................................................69

5 Factory-Installed Options 70

5.1 General Options ..................................................................................70

5.2 Cold Weather Options .........................................................................75

5.3 North Slope Options ............................................................................75

6 Technical Data 78

6.1 Engine .................................................................................................78

6.2 Generator ............................................................................................79

6.3 Machine ...............................................................................................80

6.4 Dimensions ..........................................................................................81

6.5 Radiation Compliance .........................................................................81

7 Schematics 83

7.1 LTW 20Z-1—Electrical Schematic ......................................................84

7.2 LTW 20Z-1—Electrical Schematic Components .................................85

7.3 LTW 20Z-3—Electrical Schematic ......................................................86

7.4 LTW 20Z-3—Electrical Schematic Components .................................87

7.5 Engine Wiring ......................................................................................88

7.6 Engine Wiring Components .................................................................89

7.7 Trailer Wiring (Electric Brakes) ............................................................90

7.8 Trailer Wiring Components (Electric Brakes) ......................................90

LTW 20Z Table of Contents

wc_bo5000187543_05TOC.fm 7

7.9 Trailer Wiring (Surge Brakes / No Brakes) ......................................... 91

Table of Contents LTW 20Z

8 wc_bo5000187543_05TOC.fm

LTW 20Z Safety Information

wc_si000301gb.fm 9

1 Safety Information

1.1 Signal Words Used in this Manual

1.2 This manual contains DANGER, WARNING, CAUTION, NOTICE,

and NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

1.3 Machine Description and Intended Use

This machine is a mobile, trailer-mounted light tower. The Wacker Neuson

Light Tower consists of a trailer with a cabinet containing a diesel engine, a fuel

tank, a control panel, and an electric alternator. A telescoping tower with four

metal halide lights is mounted to the top of the cabinet. Dual winches tilt, raise,

and lower the telescoping tower. As the engine runs, the generator converts

mechanical energy into electric power. The metal halide lights run off this

power. Receptacle(s) are also present to power auxiliary loads. The operator

uses the control panel to operate and monitor the machine.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

CAUTION!

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

Safety Information LTW 20Z

10 wc_si000301gb.fm

This machine is intended for the illumination of outdoor areas. This machine is

also intended for the purpose of supplying electrical power to connected loads.

Refer to the product specifications for the output voltage and frequency of this

Light Tower, and for the maximum output power limit of this Light Tower.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could permanently

damage the machine or seriously injure the operator or other persons in the

area. Machine damage caused by misuse is not covered under warranty.

 The following are some examples of misuse:

 Connecting a load that has voltage and frequency requirements that are

incompatible with the machine output

 Overloading the machine with a device that draws excessive power during

either continuous running or start-up

 Operating the machine in a manner that is inconsistent with all federal,

state and local codes and regulations

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Using the machine to tow other machines (unless factory equipped)

 Using the machine as a hoist or hanging items from the tower

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on

the machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far

as practicable and to increase operator safety through protective guards and

labeling. However, some risks may remain even after protective measures

have been taken. They are called residual risks. On this machine, they may

include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Heat from the lights

 Ultraviolet radiation from the lights

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Electric shock and arc flash

 Personal injury from improper lifting the trailer tongue

 Glare from lights (lights may blind drivers of nearby motor vehicles if the

lights are incorrectly positioned)

 Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and understand

the safety information presented in this manual before operating the machine.

LTW 20Z Safety Information

wc_si000301gb.fm 11

1.4 Safety Guidelines for Operating the Machine

Operator training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and

safety devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Personal

Protective

Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

Work area

 Make sure the area immediately surrounding the Light Tower is clean, neat,

and free of debris.

 The tower extends up to 9 m (30 ft). Make sure the area above the trailer is

open and clear of overhead wires and obstructions.

Machine setup

 Make sure the machine is on a firm, level surface and will not tip, roll, slide,

or fall while operating.

 Make sure the machine is well-grounded and securely fastened to a good

earthen ground per national and local regulations.

 The trailer must be leveled and the outriggers extended before raising the

tower. The outriggers must be extended while the tower is up.

 Never connect the machine to other power sources, such as supply mains

of power companies.

Machine

integrity

 Do not start a machine in need of repair.

 Do not use the machine if the insulation on any electrical cord is cut or worn

through.

 Do not operate the lights without the protective lens cover in place or with a

lens cover that is cracked or damaged.

 Replace or repair electrical components with components that are identical

in rating and performance to the originals.

While operating

the machine

 Keep the area behind the trailer clear of people and obstructions while rais-

ing and lowering the tower.

 Do not raise the tower or operate the machine in high winds. Lower the

tower immediately if high winds or electrical storms are expected in the

area.

Safety Information LTW 20Z

12 wc_si000301gb.fm

 Do not raise, lower, or turn the tower while the unit is operating.

 If any part of the tower hangs up, or the winch cable develops slack while

raising or lowering the tower, STOP immediately! Contact an authorized

Wacker Neuson service representative.

 Do not disengage the tower locking pin while the tower is up.

 Lamps become extremely hot in use! Allow the lamps and fixtures to cool

10–15 minutes before handling.

 Lower the tower when not in use.

1.5 Lamp Safety

Description

The lamps provided with your Light Tower are electric discharge lamps. They

are designed for use with metal halide ballasts only, and require time to reach

full brightness on initial startup and after a power interruption. These lamps

comply with FDA regulation performance standards 21 CFR 1040-30.

Operating safety

 Do not operate the lamps where people will remain for more than a few

minutes unless adequate shielding or other safety precautions are used.

 Replace damaged lamps according to the instructions in section Removing

/ Replacing Lamps.

 Lamps that automatically extinguish when the outer envelope is broken or

punctured are commercially available.

WARNING

Personal injury hazard. Lamps can cause serious skin burns and eye inflammation

from shortwave ultraviolet radiation if outer envelope of the lamp is broken or punc-

tured.

f Do not operate the Light Tower if a lamp is damaged.

LTW 20Z Safety Information

wc_si000301gb.fm 13

1.6 Operator Safety while Using Internal Combustion Engines

Operating safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.



Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immedi-

ately after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Replace the fuel tank cap after refueling.

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling. Failure to

follow the warnings and safety standards could result in severe injury or death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison. Expo-

sure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

Safety Information LTW 20Z

14 wc_si000301gb.fm

1.7 Towing Safety

Read and follow the information below:

Equipment

integrity

 Both the trailer and vehicle must be in serviceable condition and securely

fastened together.

 Ensure that the hitch and coupling on the towing vehicle are rated equal to,

or greater than, the trailer’s Gross Vehicle Weight Rating (GVWR).

 Inspect the hitch and coupling for wear or damage. Do not tow the trailer

using defective parts.

 Always connect the safety chains.

 Make sure all directional and trailer lights are connected and working prop-

erly.

 Check the tires on the trailer for tread wear, inflation, and condition.

Replace worn tires.

 Verify that all lug nuts holding the wheels are tight and none are missing.

Checking brakes

 On trailers with surge or electric brakes, connect the breakaway cable (a)

on the trailer coupler to the rear bumper or frame of the vehicle. This cable

will actuate the brake system on the trailer if both the coupling and safety

chains have failed. The breakaway cable is not a parking brake and should

not be used as one.

 Check the operation of the brakes by braking the vehicle at a slow speed

before entering traffic. Both the vehicle and the trailer should brake

smoothly. If the trailer seems to be pushing, check the fluid level (b) in the

surge brakes or the operation of the electric brakes.

Towing speed

 The maximum recommended speed for highway towing is 88 km/hour (55

mph). Recommended off-road towing speed is not to exceed 16 km/hour

(10 mph) or less depending on terrain.

WARNING

Possibility of personal injury or equipment damage. Towing a large trailer can be

hazardous without careful preparation, appropriate equipment, and/or observance

of maximum towing speeds.

f Refer to the applicable Department of Transportation regulations before towing.

wc_gr006973

a

b

LTW 20Z Safety Information

wc_si000301gb.fm 15

1.8 Service Safety

Precautions

 To reduce the risk of personal injury, read and understand the service pro-

cedures before performing any service to the machine.

 All adjustments and repairs MUST be completed before operation. Do not

operate the machine with a known problem or deficiency! All repairs and

adjustments should be completed by a qualified technician.

 Do not service the machine if your clothing or skin is wet.

Personal

Protective

Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Before servicing

the machine

 Turn the engine off before performing maintenance or making repairs.

 Make sure the engine start switch is turned to OFF.

 Make sure the circuit breakers are open (off).

 Make sure the negative terminal on the battery is disconnected.

 Do not perform even routine service (oil / oil filter changes, cleaning, etc.)

unless all electrical components are shut down.

 Make sure water has not accumulated around the base of the machine. If

water is present, move the machine and allow it to dry before servicing.

 If the machine must be started while servicing, keep hands, feet, and loose

clothing away from moving parts on the generator and engine.

Safety devices

and

modifications

 Replace all safety devices and guards after repair and maintenance.

 Do not modify the machine without the express written approval of the man-

ufacturer.

Replacing parts

and labels

 Replace worn or damaged components.

 Use only spare parts recommended by Wacker Neuson.

 Replace all missing and hard-to-read labels.

 Check all external fasteners at regular intervals.

WARNING

High voltage! This machine produces high voltage capable of causing serious injury

or death.

f Only a qualified electrician should troubleshoot or repair electrical problems

occurring with this machine.

Safety Information LTW 20Z

16 wc_si000301gb.fm

Lifting and

transporting

When lifting the machine:

 Make sure slings, chains, hooks, ramps, jacks and other types of lifting

devices are attached securely and have enough weight-bearing capacity to

lift or hold the machine safely.

 Remain aware of the location of other people when lifting the machine.

To reduce the possibility of injury:

 Do not stand under the machine while it is being hoisted or moved.

 Do not get onto the machine while it is being hoisted or moved.

LTW 20Z Labels

wc_si000386gb.fm 17

2 Labels

2.1 Label Locations

wc_gr006242

12

BB

OO

DDRR

DD

K

BB

DD

F

CC

L

V

LL

NN

SS

LL

W

FF

D

FF

DD

B

Y

Labels LTW 20Z

18 wc_si000386gb.fm

wc_gr006243

BB

Q

R

O

B

DD

GG

J

C

N

FF

D

IG

FF

E

U

V

S

A

H

HH

T

J

MM

PP

SS

JJ

T

AA

QQ

NN

KK

TT

M

LTW 20Z Labels

wc_si000386gb.fm 19

2.2 Label Meanings

A

WARNING

Automatic locking pin.

A non-secured, falling tower can cause serious

injury or death if a person is hit. To secure tower,

verify automatic locking pin has been engaged.

B

WARNING!

Avoid crushing area.

C

DANGER!

Contact with overhead electrical power lines will

cause serious injury or death. Do not position

Light Tower under electrical power lines.

WARNING!

Completely lower tower BEFORE tilting tower.

Tilting an extended tower can cause serious

injury or death.

D

NOTICE

Lifting point.

Labels LTW 20Z

20 wc_si000386gb.fm

E

WARNING!

Secure tower in transport lock before lifting or

towing. A loose swinging tower could cause per-

sonal injury or machine damage.

F

DANGER

Using a light tower indoors CAN KILL YOU IN

MINUTES. Light tower exhaust contains carbon

monoxide. This is a poison you cannot see or

smell.

NEVER use inside a home or garage, EVEN IF

doors and windows are open.

Only use OUTSIDE and far away from windows,

doors, and vents.

G

DANGER!

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an

enclosed area unless adequate

ventilation, through such items as exhaust

fans or hoses, is provided.

 Read the Operator’s Manual.

 No sparks, flames, or burning objects

near the machine.

 Stop the engine before refueling.

La page charge ...

Wacker Neuson LTW20Z3 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson LTW20Z3 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents