DeWalt DCS350D1W890B Manuel utilisateur

Marque: DeWalt

Modèle: DCS350D1W890B

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

DCS350

20V Max* Cordless Threaded Rod Cutter

Pince à couper les tiges filetées sans fil 20 V Max

Cortadora de varillas roscadas inalámbrica de 20 V máx.

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D

WALT • www.dewalt.com

Final Page Size: 8.5 in X 5.5 in

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

WALT TOOL, CALL US TOLL FREE AT: 1-800-4-D

WALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

English

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power tools

are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

English

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it away from other

metal objects, like paper clips, coins, keys, nails, screws,

or other small metal objects, that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional Speciﬁc Safety Instructions for

Thread Rod Cutter

• This threaded rod cutter is intended for cutting the following

materials and threaded rod sizes: Mild Steel (1/4-20, 3/8-16,

1/2-13), Stainless Steel (1/4-20, 3/8-16), Grade 8 Hardened

(1/4-20, 3/8-16).

• The dies provided are only used for the material and sizes

specified in the Applications chart under Intended Use.

• Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory may

contact hidden wiring. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

• Inspect tool and cutting dies before use. Replace any worn

or damaged parts. A damaged or improperly assembled tool can

break and strike operator or nearby personnel.

• NEVER have any part of your body near the cutters. A

moment of inattention while operating power tools may result in

serious personal injury.

• ALWAYS wear gloves when handling threaded rod. The ends

and threads can be sharp and can cause serious personal injury.

• Firmly secure the piece of metal to be cut to prevent

movement during cutting.

• Always wear safety shoes to protect your feet from sharp metal

debris on the floor.

• Keep all screws tight. Check periodically for loosening.

• Do not place anything into the motor housing openings.

• Stay clear of end pieces that may fall after cutting off. They

may be hot, sharp and/or heavy.

• Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in moving parts.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are

NOT safety glasses. Also use face or dust mask if cutting operation is

dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

English

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust,

which may cause serious and permanent respiratory or other

injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face

and body.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use. Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable

surface where it will not cause a tripping or falling hazard.

Some tools with large battery packs will stand upright on the battery

pack but may be easily knocked over.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ...................volts A ...................... amperes

Hz ................. hertz W ..................... watts

min ............... minutes or AC ..........alternating

or DC ... direct current current

................. Class I Construction or AC/DC ... alternating

(grounded) ........................or direct

................. Class II Construction current

(double insulated)

o ....................no load

…/min .......... per minute speed

BPM ............. beats per minute n ......................rated

IPM ............... impacts per minute ........................speed

RPM ............. revolutions per .....................earthing

minute terminal

sfpm ............. surface feet ..................... safety alert

..................... per minute symbol

SPM ............. strokes per minute ....................visible

radiation

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include the

catalog number and voltage. Consult the chart at the end of this

manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below and

then follow charging procedures outlined.

English

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable liquids,

gases or dust. Inserting or removing the battery pack from the

charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. DO NOT

modify the battery pack in any way to fit into a non-

compatible charger as battery pack may rupture causing

serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries and chargers.

• Charge the battery packs only in designated D

WALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105°F (40°C)

(such as outside sheds or metal buildings in summer). For

best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the

trigger switch locked on. Never tape the trigger switch in

the ON position.

WARNING: Fire hazard. Never attempt to open the battery pack

for any reason. If the battery pack case is cracked or damaged, do

not insert into the charger. Do not crush, drop or damage the battery

pack. Do not use a battery pack or charger that has received a sharp

blow, been dropped, run over or damaged in any way (e.g., pierced

with a nail, hit with a hammer, stepped on). Damaged battery packs

should be returned to the service center for recycling.

WARNING: Fire hazard. Do not store or carry the battery

pack so that metal objects can contact exposed battery

terminals. For example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries can possibly

cause fires if the battery terminals inadvertently come in

contact with conductive materials such as keys, coins, hand

tools and the like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit transporting batteries in

commerce or on airplanes (e.g., packed in suitcases and carry-on

luggage) UNLESS they are properly protected from short circuits. So

when transporting individual battery packs, make sure that the battery

terminals are protected and well insulated from materials that could

contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persist, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corp-

oration) Seal on the nickel cadmium, nickel metal

hydride or lithium ion batteries (or battery packs) indicate

that the costs to recycle these batteries (or battery

packs) at the end of their useful life have already been

paid by D

WALT. In some areas, it is illegal to place spent nickel

cadmium, nickel metal hydride or lithium ion batteries in the trash or

English

municipal solid waste stream and the RBRC program provides an

environmentally conscious alternative.

RBRC™, in cooperation with D

WALT and other battery users, has

established programs in the United States and Canada to facilitate

the collection of spent nickel cadmium, nickel metal hydride or lithium

ion batteries. Help protect our environment and conserve natural

resources by returning the spent nickel cadmium, nickel metal hydride

or lithium ion batteries to an authorized D

WALT service center or

to your local retailer for recycling. You may also contact your local

recycling center for information on where to drop off the spent

battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

• Before using the charger, read all instructions and cautionary

markings on the charger, battery pack and product using the

battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside the

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

WALT rechargeable battery packs. Other types of batteries may

overheat and burst resulting in personal injury and property damage.

NOTICE: Under certain conditions, with the charger plugged into the

power supply, the charger can be shorted by foreign material. Foreign

materials of a conductive nature, such as, but not limited to, grinding

dust, metal chips, steel wool, aluminum foil or any buildup of metallic

particles should be kept away from the charger cavities. Always

unplug the charger from the power supply when there is no battery

pack in the cavity. Unplug the charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging D

WALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock or electrocution.

• Do not expose the charger to rain or snow.

• Pull by the plug rather than the cord when disconnecting

the charger. This will reduce the risk of damage to the electric

plug and cord.

• Make sure that the cord is located so that it will not be

stepped on, tripped over or otherwise subjected to damage

or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry

location and use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

• An extension cord must have adequate wire size (AWG or

American Wire Gauge) for safety. The smaller the gauge number

of the wire, the greater the capacity of the cable, that is, 16 gauge

has more capacity than 18 gauge. An undersized cord will cause a

drop in line voltage resulting in loss of power and overheating. When

using more than one extension to make up the total length, be sure

each individual extension contains at least the minimum wire size.

The following table shows the correct size to use depending on

cord length and nameplate ampere rating. If in doubt, use the next

heavier gauge. The lower the gauge number, the heavier the cord.

English

Minimum Gauge for Cord Sets

Ampere

Rating

Volts Total Length of Cord

in Feet (meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not

Than

AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp blow,

been dropped or otherwise damaged in any way. Take it to

an authorized service center.

• Do not disassemble the charger; take it to an authorized

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

Chargers

Be sure to read all safety instructions before using your charger.

Consult the chart at the end of this manual for compatibility of

chargers and battery packs.

Charging a Battery (Fig. 1)

1. Plug the charger into an

appropriate outlet before inserting

battery pack.

2. Insert the battery pack (G) into the

charger, making sure the battery

pack is fully seated in the charger.

The red (charging) light will blink

continuously indicating that the

charging process has started.

3. The completion of charge will be

indicated by the red light remaining ON continuously. The battery

pack is fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger, push the

battery release button on the battery pack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before first use.

Charger Operation

Refer to the indicators below for the charge status of the battery pack.

Charge indicators: DCB101

Charging

Fully Charged

Hot/Cold Pack Delay*

Problem Pack or Charger

FIG. 1

English

Charge indicators: DCB107, DCB112, DCB113, DCB115, DCB118

Charging

Fully Charged

Hot/Cold Pack Delay*

* DCB107, DCB112, DCB113, DCB115, DCB118: The red light

will continue to blink, but a yellow indicator light will be illuminated

during this operation. Once the battery pack has reached an

appropriate temperature, the yellow light will turn off and the

charger will resume the charging procedure.

The compatible charger(s) will not charge a faulty battery pack. The

charger will indicate faulty battery pack by refusing to light or by

displaying a problem pack or charger blink pattern.

NOTE: This could also mean a problem with a charger.

If the charger indicates a problem, take the charger and battery pack

to be tested at an authorized service center.

HOT/COLD PACK DELAY

When the charger detects a battery pack that is too hot or too cold,

it automatically starts a Hot/Cold Pack Delay, suspending charging

until the battery pack has reached an appropriate temperature. The

charger then automatically switches to the pack charging mode. This

feature ensures maximum battery pack life.

A cold battery pack will charge at a slower rate than a warm battery

pack. The battery pack will charge at that slower rate throughout the

entire charging cycle and will not return to maximum charge rate even

if the battery pack warms.

The DCB118 charger is equipped with an internal fan designed to

cool the battery pack. The fan will turn on automatically when the

battery pack needs to be cooled.

Never operate the charger if the fan does not operate properly or if

ventilation slots are blocked. Do not permit foreign objects to enter

the interior of the charger.

LITHIUM-ION BATTERY PACKS ONLY

Li-Ion tools are designed with an Electronic Protection System that

will protect the battery pack against overloading, overheating or deep

discharge.

The tool will automatically turn off if the Electronic Protection System

engages. If this occurs, place the lithium-ion battery pack on the

charger until it is fully charged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118

These chargers are designed to be wall mountable or to sit upright

on a table or work surface. If wall mounting, locate the charger

within reach of an electrical outlet, and away from a corner or

other obstructions which may impede air flow. Use the back of the

charger as a template for the location of the mounting screws on the

wall. Mount the charger securely using drywall screws (purchased

separately) at least 1" (25.4 mm) long, with a screw head diameter of

0.28–0.35" (7–9mm), screwed into wood to an optimal depth leaving

approximately 7/32" (5.5 mm) of the screw exposed. Align the slots

on the back of the charger with the exposed screws and fully engage

them in the slots.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger from the AC

outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do not

use water or any cleaning solutions.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65°F and

English

75°F (18° – 24°C). DO NOT charge the battery pack in an air

temperature below +40°F (+4.5°C), or above +104°F (+40°C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to the touch

while charging. This is a normal condition, and does not indicate

a problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move the charger and battery pack to a location where the

surrounding air temperature is approximately 65 °F – 75 °F

(18° – 24°C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

4. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse effect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug the charger before

attempting to clean.

6. Do not freeze or immerse the charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside the

charger. Electric shock may result.

WARNING: Burn hazard. Do not submerge the battery pack in

any liquid or allow any liquid to enter the battery pack. Never attempt

to open the battery pack for any reason. If the plastic housing of the

battery pack breaks or cracks, return to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from

direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

Storage Recommendations

1. The best storage place is one that is cool and dry, away from

direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

English

Intended Use

This heavy duty threaded rod cutter is designed for professional

applications.

DO NOT operate or use under wet conditions or in the presence of

flammable liquids or gases.

DO NOT use for cutting tempered bolts, threads of different sizes, or

reinforcing rod.

RECOMMENDED APPLICATIONS

Rod Size Thread per Inch

Mild Steel 1/4" 20

3/8" 16

1/2" 13

Stainless Steel 1/4" 20

3/8" 16

Grade 8 Hardened 1/4" 20

3/8" 16

This is a professional power tool. DO NOT let children come into

contact with the tool. Supervision is required when inexperienced

operators use this tool.

COMPONENTS (Fig. 2)

WARNING: Never modify the power tool or any part of it. Damage

or personal injury could result.

A. Trigger switch

B. Reset/lock-off button

C. Stationary cutting die

D. Moveable cutting die

E. Hex wrench

F. Hang hook

G. Battery pack

H. Battery release button

J. LED worklight

K. Cutting die cap screws

FIG. 2

ADJUSTMENT

WARNING: To reduce the risk of serious personal injury,

turn tool off and remove the battery pack before making any

adjustments or removing/installing attachments or accessories.

An accidental start-up can cause injury.

Removing, Changing and/or Replacing

the Cutting Dies (Fig. 2, 3)

WARNING: Never attempt to repair a damaged or worn

cutting die. This could weaken the die and result in a serious injury.

Discard the entire set and replace with a new set.

The tool is equipped with a stationary cutting die (C) and a moveable

cutting die (D). Each cutting die is fabricated with three different

thread cutting sizes. Cutting die orientation is critical when changing

or replacing the cutting dies.

English

1. Loosen both cutting die cap screws (K) counterclockwise using

the hex wrench (E) provided.

2. If your desired thread cutting size is overly worn, replace both with

a new cutting die set.

3. Position the cutting dies so that both stationary cutting die and

moveable cutting die are aligned with same thread size.

NOTE: Ensure that the dots on the cutting dies are facing toward

each other and they are seated against the two perpendicular

surfaces of the stationary cutting die (C) jaw and moveable cutting

die (D) jawbefore tightening.

4. Tighten cutting die cap screws (K) clockwise using the hex

wrench (E).

5. Install a battery and cycle the tool to ensure proper assembly and

alignment prior to making a cut.

CAUTION: If the cutting die cap screws or hex wrench are lost or

damaged replace with identical replacement parts. Recommended

replacement parts for use with your tool are available at extra cost

from your local dealer or authorized service center. Always use

identical replacement parts

FIG. 3

OPERATION

WARNING: To reduce the risk of serious personal injury,

turn tool off and remove the battery pack before making any

adjustments or removing/installing attachments or accessories.

An accidental start-up can cause injury.

WARNING: Cut Hazard. NEVER have any part of your body

near the cutters. Serious personal injury may occur.

WARNING: Cut Hazard. To reduce the risk of serious

personal injury, DO NOT use the threaded rod cutter with any

kind of accessory or attachment other than those recommended by

DeWALT

WARNING: Cut Hazard. Wear gloves when handling threaded

rod. The ends and threads can be sharp and can cause serious

personal injury.

Installing and Removing the Battery Pack

(Fig. 4)

NOTE: For best results, make sure your battery pack is fully charged.

To install the battery pack (G) into the tool handle, align the battery

pack with the rails inside the tool’s handle and slide it into the handle

until the battery pack is firmly seated in the tool and ensure that it

does not disengage.

To remove the battery pack from the tool, press the release button (H)

and firmly pull the battery pack out of the tool handle. Insert it into the

charger as described in the charger section of this manual.

English

FIG. 4

FUEL GAUGE BATTERY PACKS (FIG. 4)

Some D

WALT battery packs include a fuel gauge which consists of

three green LED lights that indicate the level of charge remaining in

the battery pack.

To actuate the fuel gauge, press and hold the fuel gauge button (O).

A combination of the three green LED lights will illuminate designating

the level of charge left. When the level of charge in the battery is below

the usable limit, the fuel gauge will not illuminate and the battery will

need to be recharged.

NOTE: The fuel gauge is only an indication of the charge left on the

battery pack. It does not indicate tool functionality and is subject to

variation based on product components, temperature and end-user

application.

For more information regarding fuel gauge battery packs, please

call 1-800-4-D

WALT (1-800-433-9258) or visit our website

www.dewalt.com.

Trigger Switch (Fig. 5)

WARNING: This tool has no provision

to lock the trigger switch in the ON position

and should never be locked ON by any

other means.

To turn the tool ON, squeeze the trigger

switch (A). To turn the tool OFF release

the trigger.

Reset/Lock-Off Button

Cutting

Lock-off

Reset/Return

The spring-loaded reset/lock-off button (B) determines the direction of

the tool and also serves as a lock-off button.

To select normal cutting operation, release the trigger switch and

depress the reset/lock-off button on the right side of the tool.

The center position of the button locks the tool in the off position.

When changing the position of the reset/lock-off button, be sure the

trigger is released.

To select reset, depress and hold the reset/lock-off button on the left

side of the tool.

NOTICE: The rod cutter could stall during a cut either as a result of

a depleted battery, or as a result of cutting a material too hard or too

large.

FIG. 5

English

Should the unit stop during the cut for any reason, press and hold

the spring-loaded reset/lock-off button (B) in reset position (left side)

and pull the trigger switch (A) to open the cutter jaws and remove the

material.

NOTICE: Do not attempt to cut in the reset direction. Damage to the

tool could result.

LED Worklight (Fig. 6)

CAUTION: Do not stare into worklight. Serious eye injury could

result.

There is a worklight (J) located above the

cutting area of the tool. The worklight

is activated when the trigger switch is

depressed, and will automatically turn

off 20 seconds after the trigger switch

is released. If the trigger switch remains

depressed, the worklight will remain on.

NOTE: The worklight is for lighting the

immediate work surface and is not intended to be used as a flashlight.

Hang Hook (Fig. 2)

WARNING: To reduce the risk of injury from the threaded rod cutter

falling on operators or bystanders, make sure it is supported securely

when using the hang hook, or resting in a secure and stable location

when not in use. Be sure to keep the area below clear to reduce the

risk of the tool or off-cut material falling and striking someone or

something below.

The threaded rod cutter has a convenient hang hook (F) that allows it

to hang on a suitable, stable structure between uses. The hang hook

is not for tethering or securing the tool to a person or object during

use when elevated.

FIG. 6

Proper Hand Position (Fig. 7)

WARNING: To reduce the risk of serious personal injury, ALWAYS

use proper hand position as shown.

FIG. 7

Cutting (Fig. 8)

WARNING: Cut Hazard. Wear gloves and eye protection when

handling and cutting threaded rod. The edges are sharp and can

cause serious personal injury.

CAUTION: Cut length of threaded rod to be 1/4” (6mm) minimum.

For accurate work, always secure the workpiece before cutting.

NOTICE: Before cutting, make sure the correct die size is in place for

the intended size rod.

1. Position the threaded rod so that the material is between the

stationary cutting die (C) and moveable cutting die (D).

2. Align the threaded rod with cutting dies.

3. Depress trigger until the workpiece is fully cut.

4. Release trigger when the cutter has reached the open position.

English

When cutting overhead, always confirm workpiece is secure before

cutting and be sure the excess rod that is cut is disposed of safely.

FIG. 8

MAINTENANCE

WARNING: To reduce the risk of serious personal injury,

turn tool off and remove the battery pack before making any

adjustments or removing/installing attachments or accessories.

An accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air

at least once a week. To minimize the risk of eye injury, always wear

ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

Accessories

WARNING: Since accessories, other than those offered by

WALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk of

injury, only D

WALT recommended accessories should be used with

this product.

Recommended accessories for use with your tool are available at

extra cost from your local dealer or authorized service center. If you

need assistance in locating any accessory, please contact D

WALT

Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286,

call 1-800-4-D

WALT (1-800-433-9258) or visit our website: www.

dewalt.com.

Repairs

The charger and battery pack are not serviceable.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment (including brush inspection and replacement) should

be performed by a D

WALT factory service center, a D

WALT

authorized service center or other qualified service personnel. Always

use identical replacement parts.

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance

loss, such as fire, flood or theft, your registration of ownership will

serve as your proof of purchase.

English

• FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required

under the Federal Consumer Safety Act.

Three Year Limited Warranty

WALT will repair, without charge, any defects due to faulty materials

or workmanship for three years from the date of purchase. This

warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair

information, visit www.dewalt.com or call 1-800-4-D

WALT (1-800-

433-9258). This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have other rights

which vary in certain states or provinces.

In addition to the warranty, D

WALT tools are covered by our:

1 YEAR FREE SERVICE

WALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

2 YEARS FREE SERVICE ON D

WALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180, DCB120,

DCB201 and DCB203

3 YEARS FREE SERVICE ON D

WALT BATTERY PACKS

DCB200, DCB204

WALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any

way. D

WALT is not responsible for any injury caused by tampering

and may prosecute warranty fraud to the fullest extent permitted by

law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

WALT Power Tool, Laser, or Nailer for any reason, you can return

it within 90 days from the date of purchase with a receipt for a full

refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained in the packaging, call the local

company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

WALT (1-800-433-

9258) for a free replacement.

English

Déﬁnitions : Instructions de sécurité

Les définitions suivantes qualifient le degré de risques qui est

associé à chaque mention d'avertissement. Veuillez lire le manuel

et porter attention à ces symboles.

DANGER: indique une situation risquée imminente qui, si

elle n'est pas évitée, occasionnera des blessures graves ou

mortelles.

AVERTISSEMENT : indique une situation dangereuse

possible qui, si elle n’est pas évitée, pourra occasionner des

blessures graves ou mortelles.

MISE EN GARDE : indique une situation dangereuse

potentielle qui, si elle n'est pas évitée, occasionnera des

blessures mineures ou légères.

AVIS : indique une pratique qui n'occasionnera pas de

blessures corporelles, mais qui peut causer des dommages

matériels si elle n'est pas évitée.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE AU SUJET DE

CET OUTIL OU DE TOUT AUTRE OUTIL D

WALT, APPELEZ SANS

FRAIS AU NUMÉRO : 1-800-4-D

WALT (1-800-433-9258).

AVERTISSEMENT: Veuillez lire le manuel d'instructions afin

de réduire les risques de blessures.

Avertissements de sécurité généraux

pour les outils électriques

AVERTISSEMENT! Lire tous les avertissements de

sécurité et toutes les consignes. Le non-respect des

avertissements et des directives peut entraîner des risques de

décharge électrique, d’incendie ou de blessures graves.

CONSERVER TOUS LES AVERTISSEMENTS

ET TOUTES LES DIRECTIVES POUR UN

USAGE ULTÉRIEUR

Le terme «outil électrique» cité dans les avertissements se rapporte

à votre outil électrique à alimentation sur secteur (avec fil) ou à piles

(sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Maintenez l'espace de travail propre et bien éclairé. Les

espaces encombrés ou sombres favorisent les accidents.

b) N'utilisez pas d'outils électriques dans des

environnements explosifs, notamment en présence de

liquides, de gaz ou de poussières inflammables. Les

outils électriques créent des étincelles pouvant enflammer la

poussière ou les fumées.

c) Gardez les enfants et les autres personnes à distance

lorsque vous utilisez un outil électrique. Les distractions

peuvent vous faire perdre la maîtrise de l'outil.

2) SÉCURITÉ ÉLECTRIQUE

a) La fiche d'alimentation électrique de l'outil doit

correspondre à la prise de courant. Ne jamais modifier

la fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la terre. Des

fiches non modifiées et des prises correspondantes réduiront

le risque de décharge électrique.

b) Évitez tout contact physique avec des surfaces mises à

la terre ou à la masse comme des tuyaux, des radiateurs,

des cuisinières et des réfrigérateurs. Le risque de décharge

électrique est plus élevé si votre corps est mis à la terre.

Français

c) N'exposez pas les outils électriques à la pluie ou à

des conditions humides. L'infiltration d'eau dans un outil

électrique augmente le risque de décharge électrique.

d) Manipulez le cordon d'alimentation avec soin. Ne jamais

utiliser le cordon pour transporter, tirer ou débrancher

un outil électrique. Tenir le cordon éloigné de la chaleur,

de l’huile, des bords tranchants et des pièces mobiles.

Les cordons d'alimentation endommagés ou enchevêtrés

augmentent le risque de décharge électrique.

e) Utilisez une rallonge conçue pour un usage extérieur

lorsque vous utilisez un outil électrique à l'extérieur.

L’utilisation d’une rallonge conçue pour l’extérieur réduira les

risques de décharge électrique.

f) S'il est impossible d'éviter d'utiliser un outil électrique

dans un endroit humide, utilisez une source

d'alimentation munie d'un disjoncteur différentiel de

fuite à la terre (DDFT). L'utilisation d'un DDFT réduit le risque

de décharge électrique.

3) SÉCURITÉ PERSONNELLE

a) Restez vigilant, surveillez vos mouvements et faites

preuve de logique lorsque vous faites fonctionner un

outil électrique. Ne pas utiliser d’outil électrique en

cas de fatigue ou sous l’influence de drogues, d’alcool

ou de médicaments. Un moment d'inattention pendant le

fonctionnement des outils électriques peut occasionner des

blessures graves.

b) Utilisez un équipement de protection individuelle.

Toujours porter une protection oculaire. Dans des

conditions appropriées, l'utilisation d'équipement de protection

comme un masque antipoussière, des souliers de sécurité

avec semelle antidérapante, un casque protecteur et des

protège-tympans réduira les risques de blessures corporelles.

c) Évitez une mise en marche non intentionnelle. Assurez-

vous que l’interrupteur se trouve à la position d’arrêt

avant de relier l’outil à une source d’alimentation ou

d’insérer un bloc batterie, de ramasser ou de transporter

l’outil. Transporter un outil électrique alors que le doigt

repose sur l’interrupteur ou brancher un outil électrique dont

l’interrupteur est à la position de marche risque de provoquer

un accident.

d) Retirez toute clé de réglage avant de mettre l'outil

électrique en marche. Une clé fixée à une partie pivotante

de l’outil électrique peut provoquer des blessures corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre

en tout temps. Cela permet une meilleure maîtrise de l'outil

électrique dans des situations inattendues.

f) Habillez-vous adéquatement. Ne pas porter de vêtements

amples ni de bijoux. Garder les cheveux, les vêtements

et les gants à l’écart des pièces mobiles. Les vêtements

amples, les bijoux ou les cheveux longs peuvent se coincer

entre les pièces mobiles.

g) Si des appareils sont fournis afin d'établir le raccordement

d'installations de dépoussiérage, assurez-vous qu'ils

sont branchés et utilisés de manière appropriée.

L'utilisation d'un appareil de dépoussiérage peut réduire les

dangers liés à la poussière.

4) UTILISATION ET ENTRETIEN D'UN OUTIL ÉLECTRIQUE

a) Ne forcez pas l'outil électrique. Utiliser l’outil électrique

approprié à l’application. Un outil approprié fera un travail de

meilleure qualité et plus sécuritaire au rythme pour lequel il a été

conçu.

Français

b) N'utilisez pas un outil électrique si son interrupteur

ne permet pas de le mettre en position de marche et

d'arrêt. Tout outil électrique ne pouvant être contrôlé par un

interrupteur constitue un danger et doit être réparé.

c) Débranchez la fiche de la source d’alimentation ou

retirez le bloc batterie de l’outil électrique avant de faire

tout réglage ou changement d’accessoire ou avant de

ranger l’outil. De telles mesures de sécurité préventives

réduisent le risque de mettre accidentellement en marche un

outil électrique.

d) Rangez les outils électriques hors de la portée des

enfants et ne permettez à aucune personne n’étant pas

familière avec un outil électrique ou son mode d’emploi

d’utiliser cet outil. Les outils électriques sont dangereux entre

les mains d'utilisateurs non formés.

e) Entretien des outils électriques. Vérifier si les pièces

mobiles sont mal alignées ou coincées, si des pièces sont

brisées ou présentent toute autre condition susceptible

de nuire au bon fonctionnement de l’outil électrique.

En cas de dommage, faire réparer l’outil électrique

avant toute nouvelle utilisation. Plusieurs accidents sont

occasionnés par un entretien inadéquat des outils électriques.

f) Gardez les outils de coupe tranchants et propres. Un outil

bien entretenu, dont le bord de coupe est bien aiguisé, réduit le

risque de grippage et est plus facile à contrôler.

g) Utilisez l’outil électrique, les accessoires, les forets,

etc. conformément aux présentes directives en tenant

compte des conditions de travail et du travail à effectuer.

L'utilisation d'outils électriques pour des tâches différentes de

celles pour lesquelles ils ont été conçus pourrait entraîner une

situation dangereuse.

5) UTILISATION ET ENTRETIEN DE LA BATTERIE

a) Rechargez uniquement avec le chargeur spécifié par le

fabriquant. Un chargeur adapté à un type de batterie peut

créer un risque d'incendie s'il est utilisé avec une autre batterie.

b) N'utilisez des outils électriques qu'avec les batteries

spécifiques indiquées. L'utilisation d'autres batteries peut

créer un risque de blessure et d'incendie.

c) Lorsqu'un bloc batterie n'est pas utilisé, maintenez-

le à l'écart d'autres objets métalliques comme des

trombones, des pièces de monnaie, des clés, des clous,

des vis, ou d'autres petits objets métalliques susceptibles

de créer un contact d'une borne à l'autre. Court-circuiter

les bornes de la batterie peut provoquer des brûlures ou un

incendie.

d) Si la batterie est malmenée, un liquide peut en sortir;

évitez tout contact. En cas de contact accidentel, rincez

à l'eau. En cas de contact avec les yeux, rincez à l'eau et

consultez un médecin. Le liquide éjecté de la batterie peut

provoquer des irritations ou des brûlures.

6) RÉPARATION

a) Faites réparer votre outil électrique par un technicien

d'entretien qualifié n'utilisant que des pièces de

rechange identiques. Cela permettra de maintenir la sécurité

de l'outil électrique.

Instructions de sécurité supplémentaires

spéciﬁques pour les pinces à couper les

tiges ﬁletées

• Cette pince à couper les tiges filetées est conçue pour

couper les matières et les tailles de tiges filetées suivantes:

Acier doux (6,35 (1/4)-20, 9,5 (3/8)-16, 12,7 (1/2)-13), Acier

Français

La page charge ...

DeWalt DCS350D1W890B Manuel utilisateur

Marque: DeWalt

Modèle: DCS350D1W890B

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCS350D1W890B User manual
español: DeWalt DCS350D1W890B Manual de usuario

DeWalt DCS350D1W890B Manuel utilisateur

Ce manuel convient également à

DeWalt DCS350D1W890B Manuel utilisateur

dans d''autres langues

Documents connexes