Wacker Neuson G180 Manuel utilisateur

Mobile Generator

G 150

G 180

G 240

OPERATOR’S MANUAL

0171953en 003

0709

0171953EN

G 150 / 180 / 240 Foreword

wc_tx000869gb.fm 3

Foreword

Machine

Documentation

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 If you are missing either of these documents, please contact Wacker Neuson

Corporation to order a replacement or visit www.wackerneuson.com.

 Contact Wacker Neuson Product Support for information on servicing and

repairing the machine.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson Corporation expressly reserves the right to make technical

modifications, even without notice, which improve the performance or safety

standards of its machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson Corporation reserves the right to

change any portion of this information without notice.

Copyright

notice

 All rights, especially copying and distribution rights, are reserved.

 Copyright June 29, 2009 by Wacker Neuson Corporation.

 This publication may be reproduced through photocopying by the original

purchaser of the machine. Any other type of reproduction is prohibited without

express written permission from Wacker Neuson Corporation.

 Any type of reproduction or distribution not authorized by Wacker Neuson

Corporation represents an infringement of valid copyrights, and violators will be

prosecuted.

CALIFORNIA

Proposition

65 Warning:

Diesel engine exhaust, some of its constituents, and certain vehicle components,

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Trademarks

All trademarks referenced in this manual are the property of their respective

owners.

Foreword G 150 / 180 / 240

wc_tx000869gb.fm 4

G 150 / 180 / 240 Table of Contents

wc_bo0171953en_003TOC.fm 5

Foreword 3

1 Safety Information 7

1.1 Signal Words Found in this Manual ...................................................... 7

1.2 Safety Guidelines for Operating the Machine ....................................... 8

1.3 Operator Safety While Using Internal Combustion Engines ................. 9

1.4 Towing Safety ..................................................................................... 10

1.5 Guidelines for Service Safety ............................................................. 10

1.6 Label Locations .................................................................................. 12

1.7 Safety and Warning Labels ................................................................ 14

1.8 Informational Labels ........................................................................... 17

2 Operation 21

2.1 Application .......................................................................................... 21

2.2 Control Panel ...................................................................................... 22

2.3 Normal Boot-up Sequence ................................................................. 24

2.4 Generator monitoring ......................................................................... 26

2.5 Engine Monitoring .............................................................................. 27

2.6 Engine Shutdown Faults .................................................................... 28

2.7 Current Overload Fault ....................................................................... 29

2.8 Warning Light ..................................................................................... 30

2.9 Voltage Selector ................................................................................. 31

2.10 Emergency stop switch ...................................................................... 32

2.11 Main line circuit breaker ..................................................................... 33

2.12 Engine start switch ............................................................................. 34

2.13 Adjusting voltage with the rheostat ..................................................... 35

2.14 Connection Lugs ................................................................................ 36

2.15 Ground connection ............................................................................. 36

2.16 Convenience receptacles ................................................................... 37

2.17 Remote run terminal block ................................................................. 38

2.18 Voltage selector label ......................................................................... 39

2.19 Before starting .................................................................................... 40

2.20 Manual start-up .................................................................................. 41

2.21 Running the generator ........................................................................ 43

2.22 Engine power correction factors ......................................................... 44

2.23 Racor® Filter ...................................................................................... 45

2.24 Shutting off the generator ................................................................... 45

2.25 Cold weather start-up ......................................................................... 46

2.26 Lifting .................................................................................................. 46

2.27 Overnight storage ............................................................................... 46

G 150 / 180 / 240 Table of Contents

wc_bo0171953en_003TOC.fm 6

2.28 Long-term storage .............................................................................. 46

2.29 Automatic/remote start-up .................................................................. 47

2.30 Remote/transfer switch ....................................................................... 48

2.31 Towing ................................................................................................ 49

3 Maintenance 51

3.1 Periodic Maintenance Schedule ......................................................... 51

3.2 Breaking In New Machines ................................................................. 52

3.3 Resetting the Periodic Maintenance Timer ........................................ 52

3.4 Replacing the Air Filter Element ......................................................... 53

3.5 Replacing the Racor® Filter Element ................................................. 54

3.6 Lubricating the Engine ........................................................................ 55

3.7 Checking the Engine Coolant Level ................................................... 56

3.8 Maintaining the Trailer ........................................................................ 57

4 Factory-Installed Options 58

4.1 Block Heater ....................................................................................... 58

4.2 LCD Strip Heater ................................................................................ 59

4.3 Low Coolant Shutdown ...................................................................... 60

4.4 Lube Level Maintainer ........................................................................ 61

4.5 Temperature-Activated Shutters ........................................................ 62

4.6 Lockable Battery Disconnect .............................................................. 62

5 Schematics 64

5.1 DC Schematic (G 150 / G 180 / G 240) .............................................. 64

5.2 DC Schematic Components ............................................................... 65

5.3 AC Schematic (G 150 / G 180) ........................................................... 66

5.4 AC Schematic Components (G 150 / G 180) ..................................... 67

5.5 AC Schematic (G 240) ....................................................................... 68

5.6 AC Schematic Components (G 240) .................................................. 69

6 Technical Data 70

6.1 Engine ................................................................................................ 70

6.2 Generator Data ................................................................................... 71

6.3 Trailer and Skid Data .......................................................................... 72

6.4 Dimensions ......................................................................................... 73

G 150 / 180 / 240 Safety Information

wc_si000265gb.fm 7

1 Safety Information

1.1 Signal Words Found in this Manual

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: Contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f Obey all safety messages that follow this symbol to avoid injury or death.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f Obey all safety messages that follow this symbol to avoid possible injury or

death.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f Obey all safety messages that follow this symbol to avoid possible minor or

moderate injury.

Safety Information G 150 / 180 / 240

wc_si000265gb.fm 8wc_si000265gb.fm 8

1.2 Safety Guidelines for Operating the Machine

Before

starting the

machine

Before starting this machine:

 Have a certified electrician set up the generator set. Do not allow untrained

personnel to operate or service the generator.

 Make a walk-around inspection of the generator set before starting it. Open

side doors and visually inspect engine compartment for obvious damage or the

presence of foreign objects which might affect operation.

 Follow starting and stopping instructions described in this manual. Know how

to operate and stop the generator before starting it.

 Do not start a machine in need of repair.

 Make sure the machine is on a firm, level surface and will not tip, roll, slide, or

fall while operating.

 Remove all tools, cords, and other loose items from the generator before

starting it.

Electrical

safety

To increase electrical safety while operating this machine:

 Do not operate the generator, or tools attached to the generator, with wet

hands.

 Do not use worn electrical cords. Severe electrical shock and equipment

damage may result.

 Do not operate generator in standing water.

 Make certain the machine is well-grounded and securely fastened to a good

earthen ground per national and local regulations.

 Do not overload the generator. The total amperage of the tools and equipment

attached to the generator must not exceed the load rating of the generator.

WARNING

Machines operated improperly or by untrained personnel can be hazardous.

f Read the operating instructions contained in both this Operator’s Manual and

the engine operator’s manual.

f Familiarize yourself with the location and proper use of all controls.

f Inexperienced operators should receive instruction from someone familiar with

the machine before being allowed to operate it.

WARNING

Backfeed from the generator into the public power distribution system can seriously

injure or kill utility workers!

f Improper connection of generator to a building’s electrical system can allow

electrical current from the generator to backfeed into utility lines. This may result

in electrocution of utility workers, fire, or explosion.

f Connections to a building’s electrical system must be made by a qualified

electrician and comply with all applicable laws and electrical codes.

f If connected to a building’s electrical system, the generator must meet the

power, voltage, and frequency requirements of the equipment in the building.

G 150 / 180 / 240 Safety Information

wc_si000265gb.fm 9

Operating

safety

To increase operating safety while running this machine:

 Do not operate the generator when open containers of fuel, paint, or other

flammable liquids are in the vicinity of the generator.

 Do not place flammable material or liquids near the generator.

 Do not operate the machine indoors unless exhaust fumes can be adequately

ventilated.

 Do not touch the hot engine, exhaust, or generator components. Burns will

result.

 Do not use the emergency stop button except in case of an actual emergency.

Do not restart the engine until the cause of the trouble has been determined

and fixed.

Always do the following:

 Wear hearing protection when operating equipment.

 Keep the machine at least one meter (three feet) away from structures,

buildings, and other equipment during use.

 Keep the area immediately surrounding and underneath the machine clean,

neat, and free of debris and combustible materials. Make sure that the area

overhead is clear of debris that could fall onto or into the machine or exhaust

compartment.

Storing the

machine

Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

1.3 Operator Safety While Using Internal Combustion Engines

1. Do not run engine indoors or in an area with poor ventilation unless exhaust

hoses are used.

2. Do not fill or drain the fuel tank near an open flame, while smoking, or while the

engine is running.

3. Do not refuel a hot or running engine.

4. Refill the fuel tank in a well-ventilated area.

5. Do not touch or lean against hot exhaust pipes.

6. Replace the fuel tank cap after refueling.

7. Do not start the engine if fuel has spilled or a fuel odor is present. Move the gen-

erator away from the spill and wipe the generator dry before starting.

8. Do not remove the radiator cap when the engine is running or hot. The radiator

fluid is hot and under pressure and may cause severe burns!

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

Safety Information G 150 / 180 / 240

wc_si000265gb.fm 10wc_si000265gb.fm 10

1.4 Towing Safety

Hitch and

coupling

Before towing, follow the instructions below to ensure that the hitch and coupling

are ready for use.

 Check that the hitch and coupling on the vehicle are rated equal to, or greater

than, the trailer's Gross Vehicle Weight Rating (GVWR).

 Inspect the hitch and coupling for wear or damage. DO NOT tow the trailer

using defective parts.

 Make sure the coupling is securely fastened to the vehicle.

 Connect the safety chains.

 Connect the breakaway cable safety hook to the bumper or rear of the vehicle.

Do not attach to the vehicle hitch.

Tires and

wheels

Before towing, follow the instructions below to ensure that the tires and wheels are

ready for use.

 Check the tires on the trailer for tread wear, inflation, and condition. Replace

worn tires.

 Check that the lug nuts holding the wheels are tight and that none are missing.

Brakes and

lights

Before towing, follow the instructions below to ensure that the brakes and lights are

ready for use.

 Test the surge brakes on the trailer.

 Test the brakes on the vehicle that will be used for towing.

 Make sure directional and trailer lights are connected and working properly.

1.5 Guidelines for Service Safety

Prerequisites

Before servicing this machine:

 Stop the engine.

 If the engine has an electric starter, isconnect the negative terminal on the

battery.

 Attach a “DO NOT START” sign to the machine. This will notify everyone that

the machine is being serviced and will reduce the chance of someone

inadvertently trying to start the machine.

WARNING

Towing a large trailer requires special care. To reduce the possibility of an accident:

f Both the trailer and vehicle must be in good condition.

f The trailer and the vehicle must be securely fastened to each other.

WARNING

A poorly maintained machine can be a personal injury hazard.

f Follow the Periodic Maintenance schedule in this Operator’s Manual.

f Repair or replace any damaged or defective components immediately.

G 150 / 180 / 240 Safety Information

wc_si000265gb.fm 11

Ground

connection

 The generator must be connected to a good earthen ground for proper

operating safety!

 Ground the generator in accordance with the standards defined in national,

state, and local regulations.

Personal

injury

avoidance

 Let the engine and muffler cool before transporting or servicing the machine.

 Do not service the machine if your clothing or skin is wet.

 Do not allow untrained personnel to service this machine. Only trained

electrical technicians should be allowed to service the electrical components of

this machine.

Service safety

 Do not modify the machine without the express written approval of the

manufacturer.

 Do not allow water to accumulate around the base of the machine. If water is

present, move the machine and allow the machine to dry before servicing.

 When cleaning the unit, do not pressure wash the control panel or any other

electrical components.

..

Replacing

parts and

labels

 Replace worn or damaged components.

 Use only spare parts recommended by Wacker Neuson.

 Keep the fuel lines in serviceable condition. Leaking fuel and flames are

extremely explosive!

 Replace all missing and hard-to-read labels. Labels provide important

operating instructions and warn of dangers and hazards.

 Check all external fasteners at regular intervals.

Safety Information G 150 / 180 / 240

wc_si000265gb.fm 12wc_si000265gb.fm 12

1.6 Label Locations

G 150 / 180 / 240 Safety Information

wc_si000265gb.fm 13

wc_gr005517

G

H

J

R

GG

FF

R

A

HK

Safety Information G 150 / 180 / 240

wc_si000265gb.fm 14wc_si000265gb.fm 14

1.7 Safety and Warning Labels

Ref. Label Definition

A WARNING!

Lock doors. Access can cause electric

shock, arc flash, or injury.

B WARNING!

Pressurized contents. Do not open when hot!

CWARNING!

Read and understand the supplied

Operator’s Manual before operating the

machine. Failure to do so increases the risk

of injury to yourself or others.

DNOTICE

Never change switch position with engine

running. Results in damage to machine.

E WARNING!

Electric shock and arc flash can cause

serious injury or death.

G 150 / 180 / 240 Safety Information

wc_si000265gb.fm 15

FDANGER!

Asphyxiation hazard. Read the Operator’s

Manual for instructions. No sparks, flames,

or burning objects near machine. Stop the

engine before adding fuel. Use only diesel

fuel.

G WARNING!

To prevent hearing loss, wear hearing

protection.

Hand injury if entangled in moving belt.

Rotating machinery! Do not reach inside

with engine running.

WARNING!

Hot surface!

NOTICE

Avoid spraying water into generator.

H WARNING!

Hot surface!

J WARNING!

To prevent hearing loss, wear hearing

protection when operating the machine.

WARNING!

Pressurized contents. Do not open when hot!

WARNING!

Hand injury if entangled in moving belt.

WARNING!

Rotating machinery! Do not reach inside

machine with engine running.

K WARNING!

Disconnect battery before servicing.

Read the Operator’s Manual.

Ref. Label Definition

Safety Information G 150 / 180 / 240

wc_si000265gb.fm 16wc_si000265gb.fm 16

L WARNING!

Generator can automatically start which can

cause serious injury. Disconnect battery

before servicing.

ODANGER!

Electric shock will cause serious injury or

death. Danger of asphyxiation!

SWARNING

Stop engine. Electrical hazard. Read

Operator’s Manual.

ZWARNING

Electric shock at cooling fins.

CC Stop engine.

Ref. Label Definition

G 150 / 180 / 240 Safety Information

wc_si000265gb.fm 17

1.8 Informational Labels

Ref. Label Definition

N Voltage selector label

P

Q Operator’s Manual must be stored on

machine. Replacement Operator’s Manual

can be ordered through your local Wacker

Neuson distributor.

G 240

G 150 / G180

= 40Nm (29.5 Ft Lbs)

L3-N = 277V

L1-L2= 480V

L2-N = 277V

L1-N = 277V

L3-L1= 480V

L2-L3= 480V

L1

1

2

N

4

3

8

L-L

12

5

6

L-N

L2

10

L3

9

7

11

L-L

L2-N = 120V

L1-L2= 208V

L3-N = 120V

L1-N = 120V

L2

L3-L1= 208V

L2-L3= 208V

5

2

6

1

N

4

12

3

11

L1

9

L3

10

8

7

L-N

Safety Information G 150 / 180 / 240

wc_si000265gb.fm 18wc_si000265gb.fm 18

R Tie-down point.

T Electrical ground

UCAUTION

Lifting point.

V Operating the main circuit breaker supplies

or interrupts power to the customer

connection lugs.

W Neutral bonded to frame

X Engine wiring

Ref. Label Definition

G 150 / 180 / 240 Safety Information

wc_si000265gb.fm 19

Y

G 240

G 150 / G 180

AA A nameplate listing the model number, item

number, revision number, and serial number

is attached to each unit. Please record the

information found on this plate so it will be

available should the nameplate become lost

or damaged. When ordering parts or

requesting service information, you will

always be asked to specify the model

number, item number, revision number, and

serial number of the unit.

BB This machine may be covered by one or

more patents.

DD Remote start operation. Read Operator’s

Manual for instructions.

EE NOTICE

Receptacles not used when:

Selector switch set to 208/120V and voltage

greater than 228V.

Selector switch set to 480/277V and voltage

greater than 457V.

Ref. Label Definition

UTILITY 159116

U.S.PAT.Nos.: 6012285, 6471476,

D416858, D454357 OTHER U.S. AND

FOREIGN PATENTS PENDING

Safety Information G 150 / 180 / 240

wc_si000265gb.fm 20wc_si000265gb.fm 20

FF Hand hold

GG Protecting Our Environment

Fluid containment system

(if equipped)

Certification Label (VIN Number)

Also attached to each unit is a Certification

Label. This label specifies that the trailer

conforms with all Federal Motor Vehicle

Standards in effect at the time of

manufacture. The label includes the Vehicle

Identification Number (VIN) for the trailer.

Trailer Wiring

G - Right brake light and directional

Y - Left brake light and directional

Br - Tail, side, and license plate lights

W - Ground

L - Electric brakes

B - Battery charge

(if equipped)

CAUTION: Do not use battery

disconnect switch while engine is

running. Damage to electrical

components may occur.

Ref. Label Definition

La page charge ...

Wacker Neuson G180 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson G180 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents