Wacker Neuson G240 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur

Ce manuel convient également à

Operator’s Manual
Notice d'emploi
Mobile Generator
Groupe électrogène mobile
G230
G240
Type G230, G240
Document
5200001058
Date 0619
Revision
12
Language
EN-FR
5200001058
Copyright notice
© Copyright 2019 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operator’s Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
wc_tx004643en.fm 3
CALIFORNIA Proposition 65 Warning
CALIFORNIA Proposition 65 Warning
WARNING
The engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
WARNING
Diesel engine exhaust and some of its constituents are known to the State of
California to cause cancer, birth defects, and other reproductive harm.
WARNING
Cancer and Reproductive Harm -
www.P65Warnings.ca.gov.
WARNING
Batteries, battery posts, terminals and related accessories contain lead and lead
compounds, and other chemicals known to the State of California to cause cancer
and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.
CALIFORNIA Proposition 65 Warning Proposition 65 Warning
4 wc_tx004643en.fm
This page is intentionally left blank.
wc_tx003616gb_FM10.fm
5
Machine Identification
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine Item Number Machine Item Number
G230 5200010141
5200010142
5200010143
5000620881
5000620882
5000620883
5200007862
5100015614
5100045190
5100045596
5100045597
5100049846
5100049847
G240 5000620661
5000620662
5000620663
5200001323
5200003162
5200006904
5200025556
wc_gr010208
Serial Number:
Foreword Mobile Generator
6 wc_tx003565gb_FM10.fm
Foreword
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
For spare parts information, please see your Wacker Neuson Dealer, or visit the
Wacker Neuson website at http://www.wackerneuson.com/.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change any
portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
CALIFORNIA
Proposition
65 Warning
Combustion exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental
discharge of sparks or flames from the engine exhaust. Spark arresters are
qualified and rated by the United States Forest Service for this purpose. In order to
comply with local laws regarding spark arresters, consult the engine distributor or
the local Health and Safety Administrator.
Mobile Generator Foreword
wc_tx003565gb_FM10.fm 7
Manufacturer’s
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
Abbreviations
Abbreviation or
Acronym
Definition
Abbreviation
or Acronym
Definition
ATS Automatic transfer switch L3 Level load logic
CARB California Air Resource
Board
LT Light truck
CDL Commercial driver’s license MAF Mass air flow
CKP Crank position NC Normally closed
CMP Camshaft position NHTSA National Highway Traffic Safety
Administration
CO Carbon monoxide NOx Nitrogen oxides
DEF Diesel exhaust fluid P/L Pressure limiter
DM Dosing module PPE Personal protective equipment
DOC Diesel oxidation catalyst S/N Serial number
DTC Diagnostic trouble codes SCR Selective catalytic reduction
EGR Exhaust gas recirculation SPN Suspect parameter number
EPA Environmental Protection
Agency
ST Special trailer
ERT Extended run tank TDG Canadian Transportation of
Dangerous Goods Act
FMI Failure mode identifier TWI Treadwear indicators
GAWR Gross axle weight ratings VCW Vehicle capacity weight
IBC Intermediate bulk container
Foreword Mobile Generator
8 wc_tx003565gb_FM10.fm
This page is intentionally left blank.
Table of Contents
G150 / G180
wc_bo5000186930_12TOC.fm
9
CALIFORNIA Proposition 65 Warning 3
Foreword 6
1 Safety Information 15
1.1 Signal Words Used in this Manual ..............................................................15
1.2 Machine Description and Intended Use ......................................................16
1.3 Safety Guidelines for Operating the Machine ..............................................17
1.4 Service Safety .............................................................................................18
1.5 Operator Safety while Using Internal Combustion Engines ........................20
1.6 Safety Guidelines for Mobile Generators ....................................................21
1.7 Safety Guidelines for Towing the Machine ..................................................22
1.8 Safety Guidelines for Lifting the Machine ....................................................23
1.9 Reporting Safety Defects ............................................................................23
2 Label Locations 24
3 Label Meanings 26
4 Lifting and Transporting 37
4.1 Lifting the Machine ......................................................................................37
4.2 Before Towing Checklist ..............................................................................38
4.3 Towing the Machine ....................................................................................39
4.4 Preparing the Machine for Transport on a Truck or Trailer .........................40
4.5 Hazardous Materials Placards ....................................................................41
4.6 Testing the Breakaway System—Hydraulic Surge Brakes ..........................42
4.7 Testing the Breakaway System—Electric Brakes .......................................43
5 Machine Setup 45
5.1 Preparing the Machine for First Use ............................................................45
5.2 Positioning the Machine ..............................................................................46
5.3 Grounding the Generator ............................................................................47
5.4 Recommended Fuel ....................................................................................48
5.5 Refueling the Machine—Basler Controller ..................................................49
5.6 Refueling the Machine—Deep Sea Controller ............................................50
6 Operation, Control, and Component Locations 51
6.1 Control and Component Locations ..............................................................51
Table of Contents
G150 / G180
wc_bo5000186930_12TOC.fm
10
7 Operation—Basler Controller 53
7.1 Main Circuit Breaker ....................................................................................53
7.2 Engine Start Switch ..................................................................................... 54
7.3 Generator Pre-Alarms and Alarms (Shut-Down Conditions) .......................55
7.4 Overcurrent Condition .................................................................................56
7.5 Idle Switch ................................................................................................... 56
7.6 Diesel Particulate Filter (DPF) ..................................................................... 57
7.7 Using the Lugs and the Convenience Receptacles ..................................... 58
7.8 Selecting the Voltage ..................................................................................60
7.9 Before Starting the Machine ........................................................................63
7.10 Starting and Running the Generator ........................................................... 64
7.11 Stopping the Machine .................................................................................. 66
7.12 Emergency Stop Switch .............................................................................. 66
7.13 LCD Panel: Monitoring Machine Operation ................................................. 67
8 Working with Basler Controller 69
8.1 How to Use the Generator Controller LCD and Keypad .............................. 69
8.2 Menu Diagram of the Generator Controller ................................................. 70
8.3 Menu Diagram Components ....................................................................... 71
8.4 Using the Metering and Settings Menus ..................................................... 72
8.5 Logging in to the Generator Controller by Entering the Password .............. 73
8.6 Adjusting the LCD Screen Contrast ............................................................76
8.7 Changing the Time/Date Settings ............................................................... 77
8.8 Changing the Sender Fail Time Delays .......................................................78
8.9 Changing the Units of Measure ...................................................................80
8.10 Changing the Low Fuel Pre-Alarm Setting ..................................................81
8.11 Changing or Disabling the Low Fuel Alarm Setting ..................................... 82
8.12 Changing the Cooldown Time Setting ......................................................... 84
8.13 Changing the Pre-Crank Time Delay (Glow Plug Timer) ............................ 85
8.14 Changing the Maintenance Interval ............................................................. 87
8.15 Resetting the Maintenance Interval Pre-Alarm ............................................ 89
8.16 Resetting a Loss of Voltage Pre-Alarm ....................................................... 90
8.17 Accessing and Using the Event Log ............................................................91
9 Operation—Deep Sea Controller 93
9.1 Main Circuit Breaker ....................................................................................93
9.2 Generator Controller Power Switch .............................................................94
9.3 Selecting the Voltage ..................................................................................95
9.4 Deep Sea Controller Buttons/Functions ......................................................98
Table of Contents
G150 / G180
wc_bo5000186930_12TOC.fm
11
9.5 Generator Controller Alarms and Shut-Down Conditions ..........................100
9.6 Before Starting the Machine ......................................................................102
9.7 Starting and Running the Generator .........................................................103
9.8 Stopping the Generator .............................................................................106
9.9 Emergency Stop Switch ............................................................................107
9.10 Engine and Generator Monitoring .............................................................108
10 Working with Deep Sea Controller: DSE 7310 MKII 109
10.1 Introduction ................................................................................................109
10.2 Navigating the Menus ................................................................................110
10.3 Adjusting Screen Contrast .........................................................................112
10.4 How to Reset the Maintenance Timer .......................................................113
11 How to Connect Loads 114
11.1 Lug Terminal Connection Diagrams ..........................................................114
11.2 Best Practices for Balancing Loads ...........................................................115
11.3 Connecting 480V, 3-Phase and Single-Phase Loads ...............................117
11.4 Connecting a 240V 3Ø Load and a 240V 1Ø Load ...................................118
11.5 Connecting a 220–240V 3Ø Load and Multiple 127–133V 1Ø Loads .......119
11.6 Connecting a 208V 3Ø Load and Multiple 120V 1Ø Loads .......................120
12 Using Remote Start Capabilities 121
12.1 Remote Run Terminal Block .....................................................................121
12.2 Remote Transfer Switch ............................................................................122
12.3 Preparing for Automatic/Remote Start-Up—Deep Sea .............................123
13 Diagnostic Trouble Codes (DTC) 125
13.1 Accessing DTCs with the Basler Controller ...............................................125
13.2 Accessing Engine DTCs using the Deep Sea Controller ..........................126
13.3 List of Engine Diagnostic Trouble Codes (DTCs) ......................................127
14 Factory-Installed Options 140
14.1 Battery Charger .........................................................................................140
14.2 Lockable Battery Disconnect .....................................................................141
14.3 Camlocks ...................................................................................................142
14.4 Containment System .................................................................................142
14.5 Extended Run Tank (ERT) ........................................................................143
Table of Contents
G150 / G180
wc_bo5000186930_12TOC.fm
12
14.6 Engine Block Heater .................................................................................. 144
14.7 Cold-Weather Thermostat .........................................................................144
14.8 Low Coolant Shutdown ............................................................................. 145
14.9 Temperature-Activated Shutters ............................................................... 146
14.10 Positive Air Shutoff Valve ..........................................................................147
14.11 Connecting an External Fuel Supply ......................................................... 148
14.12 Lube Level Maintainer ...............................................................................149
15 Machines with Aftertreatment Exhaust System 150
15.1 How the Aftertreatment Exhaust System Works ....................................... 150
15.2 Filling the DEF Tank .................................................................................. 151
15.3 Shelf Life of Diesel Exhaust Fluid (DEF) ................................................... 152
15.4 Monitoring and Control of the DEF Level .................................................. 153
15.5 Monitoring DEF Quality ............................................................................. 154
15.6 Conditioning the Aftertreatment Exhaust System (if equipped) ................. 155
16 General Maintenance 156
16.1 Periodic Maintenance Schedule ................................................................ 156
16.2 Maintaining the Emission Control System .................................................157
16.3 Preparing for Maintenance ........................................................................ 157
16.4 Cleaning the Machine ................................................................................ 157
16.5 Inspecting the Machine .............................................................................158
16.6 Maintaining the Trailer ...............................................................................158
16.7 Checking and Draining the Containment System (if equipped) ................. 159
16.8 Checking the Exhaust System ..................................................................160
16.9 Maintaining the Battery .............................................................................. 161
16.10 Cleaning the Diesel Particulate Filter (DPF) (if equipped) ......................... 162
16.11 Filling the Radiator .................................................................................... 163
16.12 Replacing the Aftertreatment DEF Dosing Unit Filter (if equipped) ........... 164
16.13 Storage ...................................................................................................... 165
16.14 Machine Disposal and Decommissioning .................................................. 166
17 Engine Maintenance: John Deere 4045TF285/HF285 6068HF285 168
17.1 Heavy Duty Diesel Engine Coolant ...........................................................173
18 Engine Maintenance: T4i Cummins QSB6.7 174
18.1 Coolant Recommendations and Specifications ......................................... 177
Table of Contents
G150 / G180
wc_bo5000186930_12TOC.fm
13
19 Engine Maintenance: T4F Cummins QSB7-G9 178
20 Troubleshooting 182
21 Technical Data — G 240 183
21.1 Engine .......................................................................................................183
21.2 Generator ..................................................................................................184
21.3 Trailer and Skid .........................................................................................184
21.4 Dimensions ................................................................................................185
22 Technical Data — G 230 186
22.1 Engine: G 230 T4f .....................................................................................186
22.2 Engine: G 230 T4i .....................................................................................187
22.3 Generator ..................................................................................................188
22.4 Trailer and Skid .........................................................................................188
22.5 Dimensions ................................................................................................189
23 Tire Safety Information 190
24 User’s Information for Transport Canada Fuel Tank 202
25 Emission Control Systems Information and Warranty—Diesel 205
25.1 Emission Control System Background Information ...................................205
25.2 Limited Defect Warranty for Exhaust Emission Control System ................206
25.3 Limited Defect Warranty for Wacker Neuson Emission Control
Systems .....................................................................................................206
26 General Machine Schematics 210
26.1 Fuses .........................................................................................................210
26.2 Trailer Wiring .............................................................................................210
26.3 Trailer Wiring Components ........................................................................211
27 Schematics—Machines with Basler Controller 212
27.1 AC Schematic: G 230/G 240 .....................................................................212
27.2 AC Schematic Components: G 230/G 240 ................................................213
27.3 DC Schematic: G 240 John Deere Tier 3 ..................................................214
27.4 DC Schematic Components: G 240 Tier 3 ................................................215
Table of Contents
G150 / G180
wc_bo5000186930_12TOC.fm
14
27.5 DC Schematic: G230 Cummins T4i ..........................................................216
27.6 DC Schematic Components: G 230 T4i .................................................... 217
27.7 DC Schematic: G230 Cummins T4f ..........................................................218
27.8 DC Schematic Components: G 230 Cummins T4f .................................... 219
27.9 DC Electrical Schematic Section A: G 230 Cummins T4f ......................... 220
27.10 Electrical Schematic Components ............................................................. 221
27.11 DC Electrical Schematic Section B: G 230 Cummins T4f ......................... 222
27.12 Electrical Schematic Components ............................................................. 223
27.13 DC Electrical Schematic Section C: G 230 Cummins T4f ......................... 224
27.14 Electrical Schematic Components ............................................................. 225
27.15 Cummins Engine Relays and Fuses ......................................................... 226
27.16 Cummins Engine Relays and Fuses ......................................................... 227
28 Schematics—Machines with Deep Sea Controller 228
28.1 AC Schematic G 230 / G 240 .................................................................... 228
28.2 Electrical Schematic Components: G 230 / G 240 .................................... 229
28.3 DC Schematic: G 240 John Deere Tier 3 .................................................. 230
28.4 DC Schematic Components: G 240 John Deere Tier 3 ............................ 231
28.5 DC Schematic: G 230 Cummins T4i ......................................................... 232
28.6 DC Schematic Components: G 230 Cummins T4i .................................... 233
28.7 DC Schematic: G 230 Cummins T4f ......................................................... 234
28.8 DC Schematic Components: G 230 Cummins T4f .................................... 235
28.9 DC Electrical Schematic Section A: G 230 Cummins T4f ......................... 236
28.10 Electrical Schematic Components ............................................................. 237
28.11 DC Electrical Schematic Section B: G 230 Cummins T4f ......................... 238
28.12 Electrical Schematic Components ............................................................. 239
28.13 DC Electrical Schematic Section C: G 230 Cummins T4f ......................... 240
28.14 Electrical Schematic Components ............................................................. 241
28.15 Cummins Engine Relays and Fuses ......................................................... 242
28.16 Cummins Engine Relays and Fuses ......................................................... 243
wc_tx003567gb_FM10.fm
15
Mobile Generator Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_tx003567gb_FM10.fm
16
Safety Information Mobile Generator
1.2 Machine Description and Intended Use
Machine
description
This machine is a mobile electric power source. The Wacker Neuson Mobile
Generator consists of a trailer-mounted cabinet containing an electric alternator, a
fuel tank, and a diesel engine. A control panel, receptacles, and connection lugs
are provided on the side of the cabinet. As the engine runs, the generator converts
mechanical energy into electric power. The operator connects loads to the electric
power receptacles and connection lugs.
Intended use
This machine is intended for the purpose of supplying electrical power to
connected loads. Refer to the product specifications for the output voltage and
frequency of this generator, and for the maximum output power limit of this
generator.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
Connecting a load that has voltage and frequency requirements that are
incompatible with the generator output
Overloading the generator with a load that draws excessive power during either
continuous running or start-up
Operating the generator in a manner that is inconsistent with all federal, state
and local codes and regulations
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine to tow other machines
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Fire hazards from improper refueling techniques
Fuel and its fumes
Electric shock and arc flash
Personal injury from improper lifting the trailer tongue
Typical hazards related to towing a trailer on roads and highways
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
wc_tx003567gb_FM10.fm
17
Mobile Generator Safety Information
1.3 Safety Guidelines for Operating the Machine
Operator
training
Before operating the machine:
Read and understand the operating instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
Have received instruction on how to properly use the machine
Are familiar with required safety devices
The machine must not be accessed or operated by:
■Children
People impaired by alcohol, drugs, or prescription drugs
Application
area
Be aware of the application area.
Keep unauthorized personnel, children, and pets away from the machine.
Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Identify whether special hazards exist in the application area, such as toxic
gases or unstable ground conditions, and take appropriate action to eliminate
the special hazards before using the machine.
Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Safety
devices,
controls, and
attachments
Only operate the machine when:
All safety devices and guards are in place and in working order.
All controls operate correctly.
The machine is set up correctly according to the instructions in the Operator’s
Manual.
The machine is clean.
The machine’s labels are legible.
To ensure safe operation of the machine:
Do not operate the machine if any safety devices or guards are missing or
inoperative.
Do not modify or defeat the safety devices.
Only use accessories or attachments that are approved by Wacker Neuson.
wc_tx003567gb_FM10.fm
18
Safety Information Mobile Generator
Safe
operating
practices
When operating this machine:
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Do not operate a machine in need of repair.
Do not consume the operating fluids used in this machine. Depending on your
machine model, these operating fluids may include water, wetting agents, fuel
(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic oil,
heat transfer fluid (propylene glycol with additives), battery acid, or grease.
Personal
protective
equipment
(PPE)
Wear the following personal protective equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
After use
Stop the engine when the machine is not being operated.
Close the fuel valve on engines equipped with one when the machine is not
being operated.
Ensure that the machine will not tip over, roll, slide, or fall when not being
operated.
Store the machine properly when it is not being used. The machine should be
stored in a clean location out of the reach of children.
1.4 Service Safety
Service
training
Before servicing or maintaining the machine:
Read and understand the instructions contained in all manuals delivered with
the machine.
Familiarize yourself with the location and proper use of all controls and
protective devices.
Only trained personnel shall troubleshoot or repair problems occurring with the
machine.
Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
Do not allow untrained or improperly trained people to service or maintain the
machine. Personnel servicing or maintaining the machine must be familiar with
the associated potential risks and hazards.
Precautions
When servicing or maintaining the machine:
Read and understand the service procedures before performing any service to
the machine.
All adjustments and repairs must be completed before operating the machine.
Do not operate the machine with a known problem or deficiency.
All repairs and adjustments shall be completed by a qualified technician.
Turn off the machine before performing maintenance or making repairs.
wc_tx003567gb_FM10.fm
19
Mobile Generator Safety Information
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Reinstall the safety devices and guards after repair and maintenance
procedures are complete.
Machine
modifications
When servicing or maintaining the machine:
Use only accessories/attachments that are approved by Wacker Neuson.
Do not defeat safety devices.
Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing
parts and
labels
Replace worn or damaged components.
Replace all missing and hard-to-read labels.
When replacing electrical components, use components that are identical in
rating and performance to the original components.
When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
Cleaning
When cleaning and servicing the machine:
Keep machine clean and free of debris such as leaves, paper, cartons, etc.
Keep labels legible.
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
Personal
protective
equipment
(PPE)
Wear the following personal protective equipment (PPE) while servicing or
maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair.
Remove all jewelry (including rings).
Electrical
service safety
Make sure clothing and shoes are dry, stand on a dry wooden platform or rubber
insulating mat, and use tools with insulated handles when servicing the
machine.
Do not allow water to accumulate around the base of the machine. If water is
present, move the machine and allow the machine to dry before servicing.
Do not pressure wash the control panel, generator end, or any other electrical
components when cleaning the machine.
wc_tx003567gb_FM10.fm
20
Safety Information Mobile Generator
Cooling
system safety
Do not attempt to open the radiator cap while the unit is running or before the
engine has cooled down. Severe burns may result!
Engine coolant is toxic to humans and animals. Clean up spills and dispose of
waste engine coolant in accordance with local environmental regulations.
1.5 Operator Safety while Using Internal Combustion Engines
Operating
safety
When running the engine:
Keep the area around the exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine. Do not run the machine if fuel leaks are present or the fuel lines are
loose.
Do not smoke while operating the machine.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Do not use the machine in areas with risk of explosion or fire.
Refueling
safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Reinstall the fuel tank cap after refueling.
Use tools specifically meant for refueling (for example, a fuel hose or funnel).
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison.
Exposure to carbon monoxide can kill you in minutes.
NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through items such as exhaust fans or hoses.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487
  • Page 488 488
  • Page 489 489
  • Page 490 490
  • Page 491 491
  • Page 492 492
  • Page 493 493
  • Page 494 494
  • Page 495 495
  • Page 496 496
  • Page 497 497
  • Page 498 498
  • Page 499 499
  • Page 500 500
  • Page 501 501
  • Page 502 502
  • Page 503 503
  • Page 504 504
  • Page 505 505
  • Page 506 506
  • Page 507 507
  • Page 508 508
  • Page 509 509
  • Page 510 510
  • Page 511 511
  • Page 512 512
  • Page 513 513
  • Page 514 514
  • Page 515 515
  • Page 516 516
  • Page 517 517
  • Page 518 518
  • Page 519 519
  • Page 520 520
  • Page 521 521
  • Page 522 522
  • Page 523 523
  • Page 524 524
  • Page 525 525
  • Page 526 526
  • Page 527 527
  • Page 528 528
  • Page 529 529
  • Page 530 530
  • Page 531 531
  • Page 532 532
  • Page 533 533
  • Page 534 534

Wacker Neuson G240 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues