Wacker Neuson G240 Manuel utilisateur

Operator’s Manual

Notice d'emploi

Mobile Generator

Groupe électrogène mobile

G25 (T4i)

G25 (T4f)

Type

Document

Date

Version

Language

G25 (T4i), G25 (T4f)

5200015082

0919

11

EN-FR

5200015082

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

wc_tx004643en.fm 3

CALIFORNIA Proposition 65 Warning

WARNING

The engine exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Diesel engine exhaust and some of its constituents are known to the State of

California to cause cancer, birth defects, and other reproductive harm.

WARNING

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

WARNING

Batteries, battery posts, terminals and related accessories contain lead and lead

compounds, and other chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

CALIFORNIA Proposition 65 Warning Proposition 65 Warning

4 wc_tx004643en.fm

This page is intentionally left blank.

Mobile Generator Machine Identification

wc_tx003541gb_FM10.fm 5

Machine Identification

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine Item Number

G 25 5000620640, 5000620641, 5000620642, 5000620709,

5000620931, 5200001316, 5200003991, 5200005557,

5200009370, 5200009371, 5200009372, 5200009373,

5200009374, 5200009375, 5200009376, 5200009377,

5200014460, 5200014461, 5200014462, 5200022587,

5100014166, 5100014167, 5100017591, 5100025836,

5100041580, 5100041581, 5100041582, 5100041583,

5100041584, 5100041592, 5100042507, 5100042508,

5100042509, 5100042510, 5100042512

wc_gr013037

R

Serial Number

159047

hz

215429

For electrical

equipment only.

Pour material

electrique

seulement.

amb.temp.

Rev.

Type/Model

Item Number

rpm

lbs

PRIME RATING

kW/

kVA

kg

MADE

IN USA

V

A

Serial Number:

Foreword Mobile Generator

6 wc_tx003565gb_FM10.fm

Foreword

Machine

documentation

■ From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

■ Keep a copy of the Operator’s Manual with the machine at all times.

■ For spare parts information, please see your Wacker Neuson Dealer, or visit the

Wacker Neuson website at http://www.wackerneuson.com/.

■ When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

■ This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

■ Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

■ The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change any

portion of this information without notice.

■ The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Mobile Generator Foreword

wc_tx003565gb_FM10.fm 7

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

■ Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

■ Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

■ Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

■ Serious injury hazards to the operator and persons in the work area

■ Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Abbreviations

Abbreviation or

Acronym

Definition

Abbreviation

or Acronym

Definition

ATS Automatic transfer switch L3 Level load logic

CARB California Air Resource

Board

LT Light truck

CDL Commercial driver’s license MAF Mass air flow

CKP Crank position NC Normally closed

CMP Camshaft position NHTSA National Highway Traffic Safety

Administration

CO Carbon monoxide NOx Nitrogen oxides

DEF Diesel exhaust fluid P/L Pressure limiter

DM Dosing module PPE Personal protective equipment

DOC Diesel oxidation catalyst S/N Serial number

DTC Diagnostic trouble codes SCR Selective catalytic reduction

EGR Exhaust gas recirculation SPN Suspect parameter number

EPA Environmental Protection

Agency

ST Special trailer

ERT Extended run tank TDG Canadian Transportation of

Dangerous Goods Act

FMI Failure mode identifier TWI Treadwear indicators

GAWR Gross axle weight ratings VCW Vehicle capacity weight

IBC Intermediate bulk container — —

Foreword Mobile Generator

8 wc_tx003565gb_FM10.fm

This page is intentionally left blank.

Table of Contents

Mobile Generator

wc_bo5200015081_11TOC.fm

9

CALIFORNIA Proposition 65 Warning 3

Machine Identification 5

Foreword 6

1 Safety Information 15

1.1 Signal Words Used in this Manual ..............................................................15

1.2 Machine Description and Intended Use ......................................................16

1.3 Safety Guidelines for Operating the Machine ..............................................17

1.4 Service Safety .............................................................................................18

1.5 Operator Safety while Using Internal Combustion Engines ........................20

1.6 Safety Guidelines for Mobile Generators ....................................................21

1.7 Safety Guidelines for Towing the Machine ..................................................22

1.8 Safety Guidelines for Lifting the Machine ....................................................23

1.9 Reporting Safety Defects ............................................................................23

2 Label Locations 24

3 Label Meanings 26

4 Lifting and Transporting 36

4.1 Lifting the Machine ......................................................................................36

4.2 Before Towing Checklist ..............................................................................37

4.3 Towing the Machine ....................................................................................38

4.4 Preparing the Machine for Transport on a Truck or Trailer .........................39

4.5 Hazardous Materials Placards ....................................................................40

4.6 Testing the Breakaway System—Hydraulic Surge Brakes ..........................41

4.7 Testing the Breakaway System—Electric Brakes .......................................42

5 Machine Setup 44

5.1 Preparing the Machine for First Use ............................................................44

5.2 Positioning the Machine ..............................................................................45

5.3 Grounding the Generator ............................................................................46

5.4 Recommended Fuel ....................................................................................47

5.5 Refueling the Machine—Basler Controller ..................................................48

5.6 Refueling the Machine—Deep Sea Controller ............................................49

Table of Contents

Mobile Generator

wc_bo5200015081_11TOC.fm

10

6 Operation, Control, and Component Locations 50

6.1 Control and Component Locations ............................................................. 50

7 Operation—Basler Controller 52

7.1 Main Circuit Breaker ................................................................................... 52

7.2 Engine Start Switch ..................................................................................... 53

7.3 Generator Pre-Alarms and Alarms (Shut-Down Conditions) ...................... 54

7.4 Overcurrent Condition ................................................................................. 55

7.5 Function of the Crankcase Pressure Switch (if equipped) .......................... 56

7.6 Using the Lugs and the Convenience Receptacles .................................... 58

7.7 Selecting the Voltage .................................................................................. 60

7.8 Wet Stacking ............................................................................................... 62

7.9 Before Starting the Machine ....................................................................... 63

7.10 Starting and Running the Machine .............................................................. 64

7.11 Stopping the Machine ................................................................................. 66

7.12 Emergency Stop Switch .............................................................................. 66

7.13 LCD Panel: Monitoring Machine Operation ................................................ 67

8 Working with Basler Controller 69

8.1 How to Use the Generator Controller LCD and Keypad ............................. 69

8.2 Menu Diagram of the Generator Controller ................................................. 70

8.3 Menu Diagram Components ....................................................................... 71

8.4 Using the Metering and Settings Menus ..................................................... 72

8.5 Logging in to the Generator Controller by Entering the Password .............. 73

8.6 Adjusting the LCD Screen Contrast ............................................................ 76

8.7 Changing the Time/Date Settings ............................................................... 77

8.8 Changing the Sender Fail Time Delays ...................................................... 78

8.9 Changing the Units of Measure .................................................................. 80

8.10 Changing the Low Fuel Pre-Alarm Setting .................................................. 81

8.11 Changing or Disabling the Low Fuel Alarm Setting .................................... 82

8.12 Changing the Cooldown Time Setting ........................................................ 84

8.13 Changing the Pre-Crank Time Delay (Glow Plug Timer) ............................ 85

8.14 Changing the Maintenance Interval ............................................................ 87

8.15 Resetting the Maintenance Interval Pre-Alarm ........................................... 89

8.16 Resetting a Loss of Voltage Pre-Alarm ....................................................... 90

8.17 Accessing and Using the Event Log ........................................................... 91

Table of Contents

Mobile Generator

wc_bo5200015081_11TOC.fm

11

9 Operation—Deep Sea Controller 93

9.1 Main Circuit Breaker ....................................................................................93

9.2 Generator Controller Power Switch .............................................................94

9.3 Function of the Crankcase Pressure Switch (if equipped) ..........................95

9.4 Selecting the Voltage ..................................................................................97

9.5 Wet Stacking ...............................................................................................99

9.6 Deep Sea Controller Buttons/Functions ....................................................100

9.7 Generator Controller Alarms and Shut-Down Conditions ..........................102

9.8 Before Starting the Machine ......................................................................104

9.9 Starting and Running the Generator .........................................................105

9.10 Stopping the Generator .............................................................................107

9.11 Emergency Stop Switch ............................................................................108

9.12 Engine and Generator Monitoring .............................................................109

10 Working with Deep Sea Controller: DSE 7310 MKII 110

10.1 Introduction ................................................................................................110

10.2 Navigating the Menus ................................................................................111

10.3 Adjusting Screen Contrast .........................................................................113

10.4 How to Reset the Maintenance Timer .......................................................114

11 How to Connect Loads—480V 115

11.1 Lug Terminal Connection Diagrams ..........................................................115

11.2 Best Practices for Balancing Loads ...........................................................116

11.3 Connecting 480V, 3-Phase and Single-Phase Loads ...............................119

11.4 Connecting a 240V 3Ø Load and a 240V 1Ø Load ...................................120

11.5 Connecting 240V and 120V Single-Phase Loads .....................................121

11.6 Connecting a 208V 3Ø Load and Multiple 120V 1Ø Loads .......................122

11.7 Connecting a 220–240V 3Ø Load and Multiple 127–133V 1Ø Loads .......123

12 How to Connect Loads—600V 124

12.1 Lug Terminal Connection Diagrams ..........................................................124

12.2 Best Practices for Balancing Loads ...........................................................125

12.3 Connecting a 240V 3Ø Load and a 240V 1Ø Load ...................................128

12.4 Connecting 240V and 120V Single-Phase Loads .....................................129

12.5 Connecting a 208V 3Ø Load and Multiple 120V 1Ø Loads .......................130

12.6 Connecting a 220–240V 3Ø Load and Multiple 127–133V 1Ø Loads .......131

12.7 Connecting 480V, 3-Phase Loads .............................................................132

12.8 Connecting 600V, 3-Phase Loads .............................................................133

Table of Contents

Mobile Generator

wc_bo5200015081_11TOC.fm

12

13 Using Remote Start Capabilities 134

13.1 Remote Run Terminal Block ......................................................................134

13.2 Remote Transfer Switch ............................................................................135

13.3 Preparing for Automatic/Remote Start-Up—Deep Sea .............................136

14 Diagnostic Trouble Codes (DTC) 138

14.1 Accessing DTCs with the Basler Controller ...............................................138

14.2 Accessing Engine DTCs using the Deep Sea Controller ...........................139

14.3 List of Engine Diagnostic Trouble Codes (DTCs) ......................................140

15 Factory-Installed Options 153

15.1 Battery Charger .........................................................................................153

15.2 Lockable Battery Disconnect .....................................................................154

15.3 Camlocks ...................................................................................................155

15.4 Containment System .................................................................................156

15.5 Extended Run Tank (ERT) ........................................................................156

15.6 Engine Block Heater ..................................................................................157

15.7 Cold-Weather Thermostat .........................................................................157

15.8 Low Coolant Shutdown ..............................................................................158

15.9 Temperature-Activated Shutters ................................................................159

15.10 Positive Air Shutoff Valve ..........................................................................160

15.11 Connecting an External Fuel Supply .........................................................161

15.12 Lube Level Maintainer ...............................................................................162

16 General Maintenance 163

16.1 Periodic Maintenance Schedule ................................................................163

16.2 Maintaining the Emission Control System .................................................164

16.3 Preparing for Maintenance ........................................................................164

16.4 Cleaning the Machine ................................................................................164

16.5 Inspecting the Machine ..............................................................................165

16.6 Maintaining the Trailer ...............................................................................165

16.7 Checking and Draining the Containment System (if equipped) .................166

16.8 Checking the Exhaust System ...................................................................167

16.9 Maintaining the Battery ..............................................................................168

16.10 Cleaning the Diesel Particulate Filter (DPF) (if equipped) .........................169

16.11 Filling the Radiator .....................................................................................170

Table of Contents

Mobile Generator

wc_bo5200015081_11TOC.fm

13

16.12 Replacing the Aftertreatment DEF Dosing Unit Filter (if equipped) ...........171

16.13 Storage ......................................................................................................172

16.14 Machine Disposal and Decommissioning ..................................................173

17 Maintenance Tier 4i Engines: Isuzu 175

17.1 Coolant ......................................................................................................178

18 Maintenance Tier 4f Engines: Isuzu 179

18.1 Coolant ......................................................................................................183

19 Troubleshooting 184

20 Technical Data 185

20.1 Engine .......................................................................................................185

20.2 Generator ..................................................................................................187

20.3 Trailer and Skid .........................................................................................189

20.4 Dimensions ................................................................................................190

21 Tire Safety Information 191

22 User’s Information for Transport Canada Fuel Tank 203

23 Emission Control Systems Information and Warranty—Diesel 206

23.1 Emission Control System Background Information ...................................206

23.2 Limited Defect Warranty for Exhaust Emission Control System ................207

23.3 Limited Defect Warranty for Wacker Neuson Emission Control

Systems .....................................................................................................207

24 General Machine Schematics 211

24.1 Fuses .........................................................................................................211

24.2 Trailer Wiring .............................................................................................212

24.3 Trailer Wiring Components ........................................................................213

Table of Contents

Mobile Generator

wc_bo5200015081_11TOC.fm

14

25 Schematics—Machines with Basler Controller 214

25.1 AC Schematic ............................................................................................ 214

25.2 AC Schematic Components ......................................................................215

25.3 DC Schematic: G25, T4i Isuzu, Basler ...................................................... 216

25.4 DC Schematic Components: G25, T4i Isuzu, Basler ................................ 217

25.5 DC Schematic: G25, T4f Isuzu, Basler ...................................................... 218

25.6 DC Schematic Components: G25, T4f Isuzu, Basler ................................ 219

25.7 AC Schematic G25, Isuzu, 600V, Basler ...................................................220

25.8 AC Schematic Components G25, Isuzu, 600V, Basler ............................. 221

26 Schematics—Machines with Deep Sea Controller 222

26.1 AC Schematic: T4i, T4f .............................................................................222

26.2 AC Schematic Components: T4i, T4f ........................................................223

26.3 DC Schematic: T4i, Deep Sea .................................................................. 224

26.4 DC Schematic Components: T4i, Deep Sea ............................................. 225

26.5 DC Schematic: T4f ....................................................................................226

26.6 DC Schematic Components: T4f ...............................................................227

wc_tx003567gb_FM10.fm

15

Mobile Generators Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

► Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

► To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

► To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

► To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_tx003567gb_FM10.fm

16

Safety Information Mobile Generators

1.2 Machine Description and Intended Use

Machine

description

This machine is a mobile electric power source. The Wacker Neuson Mobile

Generator consists of a trailer-mounted cabinet containing an electric alternator, a

fuel tank, and a diesel engine. A control panel, receptacles, and connection lugs

are provided on the side of the cabinet. As the engine runs, the generator converts

mechanical energy into electric power. The operator connects loads to the electric

power receptacles and connection lugs.

Intended use

This machine is intended for the purpose of supplying electrical power to

connected loads. Refer to the product specifications for the output voltage and

frequency of this generator, and for the maximum output power limit of this

generator.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

■ Connecting a load that has voltage and frequency requirements that are

incompatible with the generator output

■ Overloading the generator with a load that draws excessive power during either

continuous running or start-up

■ Operating the generator in a manner that is inconsistent with all federal, state

and local codes and regulations

■ Using the machine as a ladder, support, or work surface

■ Using the machine to carry or transport passengers or equipment

■ Using the machine to tow other machines

■ Operating the machine outside of factory specifications

■ Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

■ Heat, noise, exhaust, and carbon monoxide from the engine

■ Fire hazards from improper refueling techniques

■ Fuel and its fumes

■ Electric shock and arc flash

■ Personal injury from improper lifting the trailer tongue

■ Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_tx003567gb_FM10.fm

17

Mobile Generators Safety Information

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

■ Read and understand the operating instructions contained in all manuals

delivered with the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Contact Wacker Neuson for additional training if necessary.

When operating this machine:

■ Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

■ Have received instruction on how to properly use the machine

■ Are familiar with required safety devices

The machine must not be accessed or operated by:

■Children

■ People impaired by alcohol, drugs, or prescription drugs

Application

area

Be aware of the application area.

■ Keep unauthorized personnel, children, and pets away from the machine.

■ Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

■ Identify whether special hazards exist in the application area, such as toxic

gases or unstable ground conditions, and take appropriate action to eliminate

the special hazards before using the machine.

■ Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

■ All safety devices and guards are in place and in working order.

■ All controls operate correctly.

■ The machine is set up correctly according to the instructions in the Operator’s

Manual.

■ The machine is clean.

■ The machine’s labels are legible.

To ensure safe operation of the machine:

■ Do not operate the machine if any safety devices or guards are missing or

inoperative.

■ Do not modify or defeat the safety devices.

■ Only use accessories or attachments that are approved by Wacker Neuson.

wc_tx003567gb_FM10.fm

18

Safety Information Mobile Generators

Safe

operating

practices

When operating this machine:

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Do not operate a machine in need of repair.

■ Do not consume the operating fluids used in this machine. Depending on your

machine model, these operating fluids may include water, wetting agents, fuel

(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic oil,

heat transfer fluid (propylene glycol with additives), battery acid, or grease.

Personal

protective

equipment

(PPE)

Wear the following personal protective equipment (PPE) while operating this

machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

After use

■ Stop the engine when the machine is not being operated.

■ Close the fuel valve on engines equipped with one when the machine is not

being operated.

■ Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

■ Store the machine properly when it is not being used. The machine should be

stored in a clean location out of the reach of children.

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

■ Read and understand the instructions contained in all manuals delivered with

the machine.

■ Familiarize yourself with the location and proper use of all controls and

protective devices.

■ Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

■ Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

■ Do not allow untrained or improperly trained people to service or maintain the

machine. Personnel servicing or maintaining the machine must be familiar with

the associated potential risks and hazards.

Precautions

When servicing or maintaining the machine:

■ Read and understand the service procedures before performing any service to

the machine.

■ All adjustments and repairs must be completed before operating the machine.

Do not operate the machine with a known problem or deficiency.

■ All repairs and adjustments shall be completed by a qualified technician.

■ Turn off the machine before performing maintenance or making repairs.

wc_tx003567gb_FM10.fm

19

Mobile Generators Safety Information

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Reinstall the safety devices and guards after repair and maintenance

procedures are complete.

Machine

modifications

When servicing or maintaining the machine:

■ Use only accessories/attachments that are approved by Wacker Neuson.

■ Do not defeat safety devices.

■ Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

■ Replace worn or damaged components.

■ Replace all missing and hard-to-read labels.

■ When replacing electrical components, use components that are identical in

rating and performance to the original components.

■ When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Cleaning

When cleaning and servicing the machine:

■ Keep machine clean and free of debris such as leaves, paper, cartons, etc.

■ Keep labels legible.

■ Do not clean the machine while it is running.

■ Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

Personal

protective

equipment

(PPE)

Wear the following personal protective equipment (PPE) while servicing or

maintaining this machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

In addition, before servicing or maintaining the machine:

■ Tie back long hair.

■ Remove all jewelry (including rings).

Electrical

service safety

■ Make sure clothing and shoes are dry, stand on a dry wooden platform or rubber

insulating mat, and use tools with insulated handles when servicing the

machine.

■ Do not allow water to accumulate around the base of the machine. If water is

present, move the machine and allow the machine to dry before servicing.

■ Do not pressure wash the control panel, generator end, or any other electrical

components when cleaning the machine.

wc_tx003567gb_FM10.fm

20

Safety Information Mobile Generators

Cooling

system safety

■ Do not attempt to open the radiator cap while the unit is running or before the

engine has cooled down. Severe burns may result!

■ Engine coolant is toxic to humans and animals. Clean up spills and dispose of

waste engine coolant in accordance with local environmental regulations.

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

■ Keep the area around the exhaust pipe free of flammable materials.

■ Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

■ Do not smoke while operating the machine.

■ Do not run the engine near sparks or open flames.

■ Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

■ Do not operate a machine when its fuel cap is loose or missing.

■ Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

■ Do not use the machine in areas with risk of explosion or fire.

Refueling

safety

When refueling the engine:

■ Clean up any spilled fuel immediately.

■ Refill the fuel tank in a well-ventilated area.

■ Reinstall the fuel tank cap after refueling.

■ Use tools specifically meant for refueling (for example, a fuel hose or funnel).

■ Do not smoke.

■ Do not refuel a hot or running engine.

■ Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

► Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

► NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through items such as exhaust fans or hoses.

La page est en cours de chargement...

Wacker Neuson G240 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson G240 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents