Wacker Neuson G70 Manuel utilisateur

Operator’s Manual

Notice d'emploi

Mobile Generator

Groupe électrogène mobile

G50

G70

Type G50, G70

Document 5200018222

Date

0918

Version

06

Language EN-FR

5200018222

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

CALIFORNIA Proposition 65 Warning

wc_tx004643en.fm

3

CALIFORNIA Proposition 65 Warning

WARNING

The engine exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Diesel engine exhaust and some of its constituents are known to the State of

California to cause cancer, birth defects, and other reproductive harm.

WARNING

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

WARNING

Batteries, battery posts, terminals and related accessories contain lead and lead

compounds, and other chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

CALIFORNIA Proposition 65 Warning

wc_tx004643en.fm

4

Notes

Mobile Generator Machine Identification

wc_tx003651gb_FM10.fm 5

Machine Identification

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine Item Number

G50 5200001060, 5200001061, 5200001062, 5200001063,

5200001317, 5200006878, 5200008339, 5200014319,

5200014320, 5200014322, 5200014323, 5200017829,

5200017830, 5100014168, 5100014169

G70 5000620646, 5000620647, 5000620648, 5000620711,

5200008340, 5200008341, 5200001318, 5200003220,

5200003973, 5200003974, 5200003975, 5200004151,

5200006879, 5200008342, 5200008343, 5200008344,

5200014463, 5200014464, 5200014465, 5100014190,

5100014191

wc_gr010874

Serial Number:

Foreword G50 / G70

6 wc_tx003565gb_FM10.fm

Foreword

Machine

documentation

■ From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

■ Keep a copy of the Operator’s Manual with the machine at all times.

■ For spare parts information, please see your Wacker Neuson Dealer, or visit the

Wacker Neuson website at http://www.wackerneuson.com/.

■ When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

■ This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

■ Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

■ The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change any

portion of this information without notice.

■ The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

G50 / G70 Foreword

wc_tx003565gb_FM10.fm 7

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

■ Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

■ Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

■ Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

■ Serious injury hazards to the operator and persons in the work area

■ Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Foreword G50 / G70

8 wc_tx003565gb_FM10.fm

Notes

Table of Contents

Mobile Generator

wc_bo5200018221_06TOC.fm

9

CALIFORNIA Proposition 65 Warning 3

Machine Identification 5

Foreword 6

1 Safety Information 17

1.1 Signal Words Used in this Manual ............................................................. 17

1.2 Machine Description and Intended Use ..................................................... 18

1.3 Safety Guidelines for Operating the Machine ............................................. 19

1.4 Service Safety ............................................................................................ 21

1.5 Operator Safety while Using Internal Combustion Engines ....................... 23

1.6 Safety Guidelines for Mobile Generators ................................................... 24

1.7 Safety Guidelines for Towing the Machine ................................................. 26

1.8 Safety Guidelines for Lifting the Machine ................................................... 27

1.9 Reporting Safety Defects ........................................................................... 27

2 Label Locations 28

3 Label Meanings 30

4 Lifting and Transporting 40

4.1 Lifting the Machine ..................................................................................... 40

4.2 Before Towing Checklist ............................................................................. 41

4.3 Towing the Machine ................................................................................... 42

4.4 Preparing the Machine for Transport on a Truck or Trailer ........................ 43

4.5 Hazardous Materials Placards ................................................................... 44

4.6 Testing the Breakaway System—Hydraulic Surge Brakes ......................... 45

4.7 Testing the Breakaway System—Electric Brakes ...................................... 47

5 Machine Setup 49

5.1 Preparing the Machine for First Use ........................................................... 49

5.2 Positioning the Machine ............................................................................. 50

5.3 Grounding the Generator ........................................................................... 52

5.4 Recommended Fuel ................................................................................... 53

5.5 Refueling the Machine—Basler Controller ................................................. 54

5.6 Refueling the Machine—Deep Sea Controller ........................................... 55

Table of Contents

Mobile Generator

wc_bo5200018221_06TOC.fm

10

6 Operation, Control, and Component Locations 56

6.1 Control and Component Locations ............................................................. 56

6.2 Control Panel Components ........................................................................ 57

7 Operation—Basler Controller 58

7.1 Main Circuit Breaker ................................................................................... 58

7.2 Engine Start Switch .................................................................................... 60

7.3 Generator Pre-Alarms and Alarms (Shut-Down Conditions) ...................... 61

7.4 Overcurrent Condition ................................................................................ 62

7.5 Function of the Crankcase Pressure Switch (if equipped) ......................... 63

7.6 Using the Lugs and the Convenience Receptacles ................................... 65

7.7 Selecting the Voltage ................................................................................. 66

7.8 Before Starting the Machine ....................................................................... 68

7.9 Starting and Running the Machine ............................................................. 69

7.10 Stopping the Machine ................................................................................ 72

7.11 Emergency Stop Switch ............................................................................. 72

7.12 LCD Panel: Monitoring Machine Operation ................................................ 73

8 Working with Basler Controller 75

8.1 How to Use the Generator Controller LCD and Keypad ............................ 75

8.2 Menu Diagram of the Generator Controller ................................................ 76

8.3 Menu Diagram Components ...................................................................... 77

8.4 Using the Metering and Settings Menus .................................................... 78

8.5 Logging in to the Generator Controller by Entering the Password ............. 79

8.6 Adjusting the LCD Screen Contrast ........................................................... 82

8.7 Changing the Time/Date Settings .............................................................. 83

8.8 Changing the Sender Fail Time Delays ..................................................... 84

8.9 Changing the Units of Measure .................................................................. 86

8.10 Changing the Low Fuel Pre-Alarm Setting ................................................. 88

8.11 Changing or Disabling the Low Fuel Alarm Setting .................................... 90

8.12 Changing the Cooldown Time Setting ........................................................ 92

8.13 Changing the Pre-Crank Time Delay (Glow Plug Timer) ........................... 94

8.14 Changing the Maintenance Interval ........................................................... 96

8.15 Resetting the Maintenance Interval Pre-Alarm .......................................... 98

8.16 Resetting a Loss of Voltage Pre-Alarm .................................................... 100

8.17 Accessing and Using the Event Log ........................................................ 101

Table of Contents

Mobile Generator

wc_bo5200018221_06TOC.fm

11

9 Operation—Deep Sea Controller 103

9.1 Main Circuit Breaker ................................................................................. 103

9.2 Generator Controller Power Switch .......................................................... 104

9.3 Function of the Crankcase Pressure Switch (if equipped) ....................... 105

9.4 Selecting the Voltage ............................................................................... 107

9.5 Deep Sea Controller Buttons/Functions ................................................... 109

9.6 Generator Controller Alarms and Shut-Down Conditions ......................... 111

9.7 Before Starting the Machine ..................................................................... 113

9.8 Starting and Running the Generator ........................................................ 114

9.9 Stopping the Generator ............................................................................ 116

9.10 Emergency Stop Switch ........................................................................... 117

9.11 Engine and Generator Monitoring ............................................................ 118

10 Working with Deep Sea Controller: DSE 7310 MKII 119

10.1 Introduction ............................................................................................... 119

10.2 Navigating the Menus ............................................................................... 120

10.3 Adjusting Screen Contrast ........................................................................ 122

10.4 How to Reset the Maintenance Timer ...................................................... 123

11 How to Connect Loads—480V 124

11.1 Lug Terminal Connection Diagrams ......................................................... 124

11.2 Best Practices for Balancing Loads .......................................................... 125

11.3 Connecting 480V, 3-Phase and Single-Phase Loads .............................. 128

11.4 Connecting a 240V 3Ø Load and a 240V 1Ø Load .................................. 129

11.5 Connecting 240V and 120V Single-Phase Loads .................................... 130

11.6 Connecting a 208V 3Ø Load and Multiple 120V 1Ø Loads ...................... 131

11.7 Connecting a 220–240V 3Ø Load and Multiple 127–133V

1Ø Loads .................................................................................................. 132

12 How to Connect Loads—600V 133

12.1 Lug Terminal Connection Diagrams ......................................................... 133

12.2 Best Practices for Balancing Loads .......................................................... 134

12.3 Connecting a 240V 3Ø Load and a 240V 1Ø Load .................................. 137

12.4 Connecting 240V and 120V Single-Phase Loads .................................... 138

12.5 Connecting a 208V 3Ø Load and Multiple 120V 1Ø Loads ...................... 139

12.6 Connecting a 220–240V 3Ø Load and Multiple 127–133V

1Ø Loads .................................................................................................. 140

12.7 Connecting 480V, 3-Phase Loads ............................................................ 141

12.8 Connecting 600V, 3-Phase Loads ............................................................ 142

Table of Contents

Mobile Generator

wc_bo5200018221_06TOC.fm

12

13 Using Remote Start Capabilities 143

13.1 Remote Run Terminal Block .................................................................... 143

13.2 Remote Transfer Switch ........................................................................... 144

13.3 Preparing for Automatic/Remote Start-Up—Basler .................................. 145

13.4 Preparing for Automatic/Remote Start-Up—Deep Sea ............................ 146

14 Diagnostic Trouble Codes (DTC) 148

14.1 Accessing DTCs with the Basler Controller .............................................. 148

14.2 Accessing Engine DTCs using the Deep Sea Controller ......................... 149

14.3 List of Engine Diagnostic Trouble Codes (DTCs) ..................................... 150

15 Factory-Installed Options 164

15.1 Battery Charger ........................................................................................ 164

15.2 Lockable Battery Disconnect .................................................................... 165

15.3 Camlocks .................................................................................................. 166

15.4 Containment System ................................................................................ 167

15.5 Extended Run Tank (ERT) ....................................................................... 167

15.6 Engine Block Heater ................................................................................. 168

15.7 Cold-Weather Thermostat ........................................................................ 169

15.8 Low Coolant Shutdown ............................................................................ 170

15.9 Temperature-Activated Shutters .............................................................. 171

15.10 Positive Air Shutoff Valve ......................................................................... 172

15.11 Connecting an External Fuel Supply ........................................................ 173

15.12 Lube Level Maintainer .............................................................................. 174

16 Machines with Aftertreatment Exhaust System 175

16.1 How the Aftertreatment Exhaust System Works ...................................... 175

16.2 Filling the DEF Tank ................................................................................. 176

16.3 Shelf Life of Diesel Exhaust Fluid (DEF) .................................................. 178

16.4 Monitoring and Control of the DEF Level ................................................. 179

16.5 Monitoring DEF Quality ............................................................................ 180

17 General Maintenance 181

17.1 Periodic Maintenance Schedule ............................................................... 181

17.2 Maintaining the Emission Control System ................................................ 182

17.3 Preparing for Maintenance ....................................................................... 182

17.4 Cleaning the Machine ............................................................................... 182

Table of Contents

Mobile Generator

wc_bo5200018221_06TOC.fm

13

17.5 Inspecting the Machine ............................................................................ 183

17.6 Maintaining the Trailer .............................................................................. 184

17.7 Checking and Draining the Containment System (if equipped) ................ 185

17.8 Checking the Exhaust System ................................................................. 186

17.9 Maintaining the Battery ............................................................................. 187

17.10 Cleaning the Diesel Particulate Filter (DPF) (if equipped) ........................ 188

17.11 Filling the Radiator ................................................................................... 189

17.12 Replacing the Aftertreatment DEF Dosing Unit Filter (if equipped) .......... 191

17.13 Storage ..................................................................................................... 193

17.14 Machine Disposal and Decommissioning ................................................. 194

18 Engine Maintenance: John Deere 4045TF285/HF285 6068HF285 195

18.1 Heavy Duty Diesel Engine Coolant .......................................................... 200

19 Engine Maintenance: John Deere 4045TF/280290 4045HF280 201

19.1 Heavy Duty Diesel Engine Coolant .......................................................... 205

20 Engine Maintenance: T4i Cummins QSB6.7 206

20.1 Coolant Recommendations and Specifications ........................................ 209

21 Maintenance Tier 4f Engines: Isuzu 210

21.1 Coolant ..................................................................................................... 215

22 Troubleshooting 216

23 Technical Data: G50, T4i John Deere 217

23.1 Engine ...................................................................................................... 217

23.2 Generator ................................................................................................. 218

23.3 Machine .................................................................................................... 219

23.4 Trailer and Skid ........................................................................................ 219

23.5 Dimensions ............................................................................................... 220

Table of Contents

Mobile Generator

wc_bo5200018221_06TOC.fm

14

24 Technical Data: G50, T4f Isuzu 221

24.1 Engine ...................................................................................................... 221

24.2 Generator ................................................................................................. 222

24.3 Machine .................................................................................................... 223

24.4 Trailer and Skid ........................................................................................ 223

24.5 Dimensions ............................................................................................... 224

25 Technical Data: G70, T3 John Deere, 600V 225

25.1 Engine ...................................................................................................... 225

25.2 Generator ................................................................................................. 226

25.3 Machine .................................................................................................... 226

25.4 Trailer ....................................................................................................... 227

25.5 Dimensions ............................................................................................... 228

26 Technical Data: G70, T4i Cummins 229

26.1 Engine ...................................................................................................... 229

26.2 Generator ................................................................................................. 230

26.3 Machine .................................................................................................... 230

26.4 Trailer and Skid ........................................................................................ 231

26.5 Dimensions ............................................................................................... 232

27 Tire Safety Information 233

28 User’s Information for Transport Canada Fuel Tank 245

29 Emission Control Systems Information and Warranty—Diesel 248

29.1 Emission Control System Background Information .................................. 248

29.2 Limited Defect Warranty for Exhaust Emission Control System .............. 249

29.3 Limited Defect Warranty for Wacker Neuson Emission Control

Systems .................................................................................................... 249

30 General Machine Schematics 253

30.1 Fuses ........................................................................................................ 253

30.2 Trailer Wiring ............................................................................................ 254

30.3 Trailer Wiring Components ....................................................................... 255

Table of Contents

Mobile Generator

wc_bo5200018221_06TOC.fm

15

31 Schematics—Machines with Deep Sea Controller 256

31.1 AC Schematic: G50 .................................................................................. 256

31.2 AC Schematic Components: G50 ............................................................ 257

31.3 DC Schematic: G50 .................................................................................. 258

31.4 DC Schematic Components: G50 ............................................................ 259

31.5 AC Schematic: G70 .................................................................................. 260

31.6 AC Schematic Components: G70 ............................................................ 261

Table of Contents

Mobile Generator

wc_bo5200018221_06TOC.fm

16

wc_tx003567gb_FM10.fm

17

Mobile Generator Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

► Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

► To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

► To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

► To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_tx003567gb_FM10.fm

18

Safety Information Mobile Generator

1.2 Machine Description and Intended Use

Machine

description

This machine is a mobile electric power source. The Wacker Neuson Mobile

Generator consists of a trailer-mounted cabinet containing an electric alternator, a

fuel tank, and a diesel engine. A control panel, receptacles, and connection lugs

are provided on the side of the cabinet. As the engine runs, the generator converts

mechanical energy into electric power. The operator connects loads to the electric

power receptacles and connection lugs.

Intended use

This machine is intended for the purpose of supplying electrical power to

connected loads. Refer to the product specifications for the output voltage and

frequency of this generator, and for the maximum output power limit of this

generator.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

■ Connecting a load that has voltage and frequency requirements that are

incompatible with the generator output

■ Overloading the generator with a load that draws excessive power during either

continuous running or start-up

■ Operating the generator in a manner that is inconsistent with all federal, state

and local codes and regulations

■ Using the machine as a ladder, support, or work surface

■ Using the machine to carry or transport passengers or equipment

■ Using the machine to tow other machines

■ Operating the machine outside of factory specifications

■ Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

■ Heat, noise, exhaust, and carbon monoxide from the engine

■ Fire hazards from improper refueling techniques

■ Fuel and its fumes

■ Electric shock and arc flash

■ Personal injury from improper lifting the trailer tongue

■ Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_tx003567gb_FM10.fm

19

Mobile Generator Safety Information

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

■ Read and understand the operating instructions contained in all manuals

delivered with the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Contact Wacker Neuson for additional training if necessary.

When operating this machine:

■ Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

■ Have received instruction on how to properly use the machine

■ Are familiar with required safety devices

The machine must not be accessed or operated by:

■ Children

■ People impaired by alcohol, drugs, or prescription drugs

Application

area

Be aware of the application area.

■ Keep unauthorized personnel, children, and pets away from the machine.

■ Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

■ Identify whether special hazards exist in the application area, such as toxic

gases or unstable ground conditions, and take appropriate action to eliminate

the special hazards before using the machine.

■ Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

■ All safety devices and guards are in place and in working order.

■ All controls operate correctly.

■ The machine is set up correctly according to the instructions in the Operator’s

Manual.

■ The machine is clean.

■ The machine’s labels are legible.

To ensure safe operation of the machine:

■ Do not operate the machine if any safety devices or guards are missing or

inoperative.

■ Do not modify or defeat the safety devices.

■ Only use accessories or attachments that are approved by Wacker Neuson.

Safe

operating

practices

When operating this machine:

wc_tx003567gb_FM10.fm

20

Safety Information Mobile Generator

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Do not operate a machine in need of repair.

■ Do not consume the operating fluids used in this machine. Depending on your

machine model, these operating fluids may include water, wetting agents, fuel

(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic oil,

heat transfer fluid (propylene glycol with additives), battery acid, or grease.

Personal

Protective

Equipment

(PPE)

Wear the following personal protective equipment (PPE) while operating this

machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

After use

■ Stop the engine when the machine is not being operated.

■ Close the fuel valve on engines equipped with one when the machine is not

being operated.

■ Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

■ Store the machine properly when it is not being used. The machine should be

stored in a clean location out of the reach of children.

La page charge ...

Wacker Neuson G70 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson G70 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents