Hilti DX 460 GR Mode d'emploi

Catégorie
Outils électroportatifs
Taper
Mode d'emploi
DX 460 GR
282821
Operating instructions en
Mode d’emploi fr
zh
ko
ar
cn
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
1
3
5
4
6
13
15
14
11
12
1
2
9
10
7
8
D
X
46
0
D
X
46
0
X
-
4
6
0
-
F
G
R
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
6.1
7.1
2
7.2
7.3
7.4
7.6
3
2
7.5
3
4
5
7.5
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
2
4
3
1
8.14
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
1
en
ORIGINAL OPERATING INSTRUCTIONS
DX 460 GR powder-actuated tool for grating applications
Description of main parts
@ Exhaust gas piston return unit
; Guide sleeve
= Housing
% Cartridge guideway
& Power regulation wheel release button
( Power regulation wheel
) Trigger
+ Grip
§ Piston return unit release button
/ Ventilation slots
: Piston rings
· Piston *
$ Replaceable fastener guide nosepiece *
£ Fastener guide release button
| Buffer *
* These parts may be replaced by the user/operator.
It is essential that the operating instruc-
tions are read before the tool is operated
for the first time.
Always keep these operating instructions
together with the tool.
Ensure that the operating instructions
are with the tool when it is given to other
persons.
Contents Page
1. Safety precautions 1
2. General information 3
3. Description 3
4. Accessories 4
5. Technical data 6
6. Before use 6
7. Operation 7
8. Care and maintenance 8
9. Troubleshooting 10
10. Disposal 12
11. Manufacturer's warranty – DX Tools 13
12. EC declaration of conformity (original) 13
13. CIP approval mark 13
14. Health and safety of the user 14
1. Safety precautions
1.1 Basic safety instructions
In addition to the safety precautions listed in the indi-
vidual sections of these operating instructions, the
following points must be strictly observed at all times.
1.2 Only use Hilti cartridges or cartridges of equiva-
lent quality
The use of cartridges of inferior quality in Hilti tools may
lead to build-up of unburned powder, which may explo-
de and cause severe injuries to operators and bystan-
ders. At a minimum, cartridges must either:
a) Be confirmed by their supplier to have been suc-
cessfully tested in accordance with EU standard EN
16264
NOTE:
All Hilti cartridges for powder-actuated tools have
been tested successfully in accordance with EN 16264.
The tests defined in the EN 16264 standard are system
tests carried out by the certification authority using
specific combinations of cartridges and tools.
The tool designation, the name of the certification aut-
hority and the system test number are printed on the
cartridge packaging.
or
b) Carry the CE conformity mark (mandatory in the EU
as of July 2013).
See packaging sample at:
www.hilti.com/dx-cartridges
1.3 Use as intended
The tool is designed for professional use in fastening
applications in construction where nails, threaded studs
and composite fasteners are driven into concrete, steel
and sand-lime block masonry.
1.4 Improper use
Manipulation or modification of the tool is not per-
missible.
Do not operate the tool in an explosive or flammable
atmosphere, unless the tool is specially approved for
such use.
To avoid the risk of injury, use only original Hilti fas-
teners, cartridges, accessories and spare parts or those
of equivalent quality.
Observe the information printed in the operating
instructions concerning operation, care and mainte-
nance.
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
2
en
Never point the tool at yourself or any bystander.
Never press the muzzle of the tool against your hand
or other part of your body.
Do not drive nails into excessively hard or brittle mate-
rials such as glass, marble, plastic, bronze, brass, cop-
per, natural rock, insulation material, hollow brick, glazed
tile, thin-gauge sheet metal (< 4 mm), grey cast iron,
spheroidal cast iron and gas concrete.
1.5 Technology
This tool is designed with the latest available tech-
nology.
The tool and its ancillary equipment may present haz-
ards when used incorrectly by untrained personnel or
not as directed.
1.6 Making the workplace safe
Ensure that the workplace is well lit.
Objects which could cause injury should be removed
from the working area.
Operate the tool only in well-ventilated working areas.
The tool is for hand-held use only.
Avoid unfavorable body positions. Work from a secure
stance and stay in balance at all times
Keep other persons, children in particular, outside the
working area.
Before using the tool, make sure that no one
is standing behind or below the point where fasteners
are to be driven.
Keep the grip dry, clean and free from oil and grease.
1.7 General safety precautions
Operate the tool only as directed and only when it is
in faultless condition.
If a cartridge misfires or fails to ignite, proceed as fol-
lows:
1. Keep the tool pressed against the working surface for
30 seconds.
2. If the cartridge still fails to fire, withdraw the tool from
the working surface, taking care that it is not pointed
towards your body or bystanders.
3. Manually advance the cartridge strip one cartridge.
Use up the remaining cartridges on the strip. Remove
the used cartridge strip and dispose of it in such a
way that it can be neither reused nor misused.
If 2–3 cartridge misfires occur in succession (with-
out clearly audible noise of the cartridge firing and the
fastener being driven with significantly less power), pro-
ceed as follows:
1. Stop using the tool immediately.
2. Unload and disassemble the tool (see 8.3).
3. Check that the correct combination of fastener
guide, piston and fastener are used (see 6.2).
4. Check the buffer, piston and fastener guide for wear
and replace the parts if necessary (see 8.4).
5. Clean the tool.
6. Do not continue to use the tool if the problem per-
sists after carrying out the steps described above.
Have the tool checked and repaired if necessary at
a Hilti repair center.
Never attempt to pry a cartridge from the magazine
strip or the tool.
Keep the arms flexed when the tool is fired (do not
straighten the arms).
Never leave the loaded tool unattended.
Always unload the tool before beginning cleaning,
servicing or changing parts and before storage.
Unused cartridges and tools not presently in use
must be stored in a place where they are not exposed
to humidity or excessive heat. The tool should be trans-
ported and stored in a toolbox that can be locked or
secured to prevent use by unauthorized persons.
1.8 Temperature
Do not disassemble the tool while it is hot.
Never exceed the recommended maximum fastener
driving rate (number of fastenings per hour). The tool
may otherwise overheat.
Should the plastic cartridge strip begin to melt, stop
using the tool immediately and allow it to cool down.
1.9 Requirements to be met by users
The tool is intended for professional use.
The tool may be operated, serviced and repaired only
by authorised, trained personnel. This personnel must
be informed of any special hazards that may be encoun-
tered.
Proceed carefully and do not use the tool if your full
attention is not on the job.
Stop working with the tool if you feel unwell.
1.10 Personal protective equipment
The operator and other persons in the immediate vicin-
ity must always wear eye protection, a hard hat and ear
protection.
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
3
en
3. Description
The tool is designed for professional use in fastening
applications where nails, threaded studs and compo site
fasteners are driven into concrete, steel and sand-lime
block masonry.
The tool works on the well-proven piston principle and
is therefore not related to high-velocity tools. The pis-
ton principle provides an optimum of working and fas-
tening safety. The tool works with cartridges of 6.8/11
caliber.
The piston is returned to the starting position and the
cartridges are fed to the firing chamber automatically
by gas pressure from the fired cartridge. This permits
fastenings to be made very quickly and economically
with nails and threaded studs.
As with all powder-actuated tools, the tool, fastener pro-
gram and cartridge program form a “technical unit”.
This means that optimal fastening with this system can
only be assured if the fasteners and cartridges are
specially manufactured for it, or products of equivalent
quality, are used. The fastening and application recom-
mendations given by Hilti are only applicable if these
conditions are observed.
The tool features 5-way safety – for the safety of the
operator and bystanders.
The piston principle
The energy from the propellant charge is transferred to
a piston, the accelerated mass of which drives the fastener
into the base material. As approximately 95 % of the
kinetic energy is absorbed by the piston, the fastener is
driven into the base material at much reduced velocity
(less than 100 m/sec.) in a controlled manner. The dri-
ving process ends when the piston reaches the end of
its travel. This makes dangerous through-shots virtual-
ly impossible when the tool is used correctly.
The drop-firing safety device is the result of coupling
the firing mechanism with the cocking movement. This
prevents the Hilti DX tool from firing when it is dropped
onto a hard surface, no matter at which angle the impact
occurs.
The trigger safety device ensures that the cartridge
cannot be fired simply by pulling the trigger only. The
tool can be fired only when pressed against the work
surface.
The contact pressure safety device requires the tool
to be pressed against the work surface with a signifi-
4
3
2
1
Warning signs
General
warning
Warning:
hot surface
Obligation signs
Wear eye
protection
Wear a
safety helmet
Wear ear
protection
Symbols
Read the opera-
tion instructions
before use
2. General information
2.1 Signal words and their meaning
WARNING
The word WARNING is used to draw attention to a poten-
tially dangerous situation which could lead to severe
personal injury or death.
CAUTION
The word CAUTION is used to draw attention to a poten-
tially dangerous situation which could lead to minor per-
sonal injury or damage to the equipment or other prop-
erty.
2.2 Pictograms
The numbers refer to the illustrations. The illustra-
tions can be found on the fold-out cover pages. Keep
these pages open while you read the operating instruc-
tions.
In these operating instructions, the designation “the
tool” always refers to the DX460GR powder-actuated
tool.
Location of identification data on the tool
The type designation and the serial number are printed
on the type plate on the tool. Make a note of this infor-
mation in your operating instructions and always refer
to it when making an enquiry to your Hilti representa-
tive or service department.
Type: DX460GR
Serial no.:
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
4
en
cant force. The tool can be fired only when pressed ful-
ly against the work surface in this way.
In addition, all Hilti DX tools are equipped with an unin-
tentional firing safety device . This prevents the tool
from firing if the trigger is pulled and the tool then pressed
against the work surface. The tool can be fired only when
it is first pressed (1.) against the work surface correct-
ly and the trigger then pulled (2.).
5
1
2
4
2
5
3
4. Cartridges, accessoires and fasteners
Threaded studs
Ordering designation Application
X-EM Zinc plated stud for indoors, dry and non corrosive environment
X-CRM Stainless steel studs for outdoor or/and corrosive environement (not recommended
in tunnels, swimming pool or similar environment)
X-GR-RU Duplex coated (comparable to Hot Dip Galvanised steel) discs for indoor, midly
corrosive environment, or for limited lifetime use. Not for use in marine atmosphere
or in heavily polluted environement
X-FCM Grating discs
Ordering designation Application
X-FCM Zinc plated discs for indoors, dry and non corrosive environment
X-FCM-M Duplex coated (comparable to Hot Dip Galvanised steel) discs for indoor, midly
corrosive environment, or for limited lifetime use. Not for use in marine atmosphere
or in heavily polluted environement
X-FCM-R Stainless steel discs for outdoor or/and corrosive environement (not recommended
in tunnels, swimming pool or similar environment)
X-FCP Checker plates
Ordering designation Application
X-FCP-M Duplex coated (comparable to Hot Dip Galvanised steel) discs for indoor, midly
corrosive environment, or for limited lifetime use. Not for use in marine atmosphere
or in heavily polluted environment
X-FCP-R Stainless steel plates for outdoor or/and corrosive environement (not recommended
in tunnels, swimming pool or similar environment)
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
5
en
Hilti recommendations for grating application areas
Application areas X-FCM + X-EM X-FCM-M + X-CRM
X-GR-RU + X-CRM
X-FCM-R + X-CRM
Indoors, dry and non
corrosive environment
Indoors, outdoors, midly cor-
rosive environment
Marine atmosphere, heavily
polluted environment
Tunnel,swimming pools or
similar environment
Most relevant product for application
Could be used for application
Not used for the application
Important:
Do not use a zinc plated X-EM stud with X-FCM-M*, X-GR-RU* or X-FCM-R** grating disc.
Always use a stainless steel X-CRM stud.
** (Duplex coated)
** (Stainless steel)
Fastener guide
Ordering designation Application
X-460-F8GR Grating baseplate for 8mm studs
Piston
Ordering designation Application
X-460-PGR Piston for grating applications
Accessories
Ordering designation Application
Centering devices To center perfectly the studs
S-B HEX5Bit To screw/unscrew X-FCM grating discs
S-NSX 2.815bit To screw/unscrew X-FCP checker plates
X-460-TGR Replacement nosepiece for the X-460-F8GR fastener guide
Cartridges
Ordering designation Colour code Power level
6.8/11 M green Green Low
6.8/11 M yellow Yellow Medium
6.8/11 M red Red Heavy
6.8/11 M black Black/purple Extra heavy
Cleaning set
Hilti spray, flat brush, large round brush, small round brush, scraper, cleaning cloth.
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
6
en
6. Before use
쎱쎱
6.1 Tool inspection
Ensure that there is no cartridge strip in the tool. If
there is a cartridge strip in the tool, remove it by hand
from the tool.
Check all external parts of the tool for damage at reg-
ular intervals and check that all controls operate prop-
erly. Do not operate the tool when parts are damaged or
when the controls do not operate properly. If necessary,
have the tool repaired at a Hilti service centre.
Check the buffer and piston for wear (see “8. Care
and maintenance”).
5. Technical data
DX 460 GR tool
Weight 3.85 Kg (8.49 lb)
Tool length 478 mm (18.8")
Recommended maximum fastening rate 700 per hour
Cartridges 6.8/11 M (27 cal. short) green, yellow, red, black
Power regulation 4 cartridge power levels, regulation wheel with locking
function
Right of technical changes reserved
6.2 Choosing the right fastener guide / piston / fas-
tener combination
Use of the wrong combination may present a risk of
injury. Damage to the tool may also result or fastening
quality may be negatively affected.
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
7
en
7. Operation
CAUTION
The nail or stud is driven by a car-
tridge being fired.
Excessive noise may damage the
hearing.
Wear ear protection (users and
bystanders).
WARNING
The tool could be made ready to
fire if pressed against a part of
the body (e.g. hand)..
This could cause a nail to be dri-
ven into a part of the body.
Never press the muzzle of the tool
against parts of the body.
WARNING
Under certain circumstances, the
tool could be made ready to fire
by pulling back the fastener guide
or the fastener by hand.
When in the “ready to fire” state,
a fastener could be driven into a
part of the body.
Never pull back the fastener guide
or fastener by hand.
CAUTION
The base material may splinter
when a fastener is driven or frag-
ments of the cartridge strip may
fly off.
Flying fragments may injure parts
of the body or the eyes.
Wear safety goggles and a hard
hat (users and bystanders).
Guidelines for optimum fastening quality
NOTE
These application recommendations must always be
observed. For more specific information, refer to the
Hilti Fastening Technology Manual, which is available
from your local Hilti organisation.
Steel
A = min. edge distance = 15 mm (
5
/
8
")
B = min. spacing = 20 mm (
3
/
4
")
C = min. base material thickness = 4 mm (
5
/
32
")
Penetration depth in steel: 12 ± 2 mm
BA
d
C
쎱쎱
7.1 Loading the tool
1. Insert the fastener (head first) until the washer is held
in the tool.
2. Load the cartridge strip (narrow end first) by insert-
ing it into the bottom of the tool grip until flush. If
the strip has been partly used, pull it through until
a live cartridge is in the chamber. (The last visible
number on the back of the cartridge strip indicates
which cartridge is next to be fired.)
쎱쎱
7.2 Adjusting the driving power
Select a cartridge power level and power setting to suit
the application. If you cannot estimate this on the basis
of previous experience, always begin with the lowest
power.
1. Press the release button.
2. Turn the power regulation wheel to 1.
3. Drive a fastener.
4. If the fastener doesn't penetrate deeply enough,
increase the power level and repeat steps 1 to 3.
Repeat until the desired depth of penetration is
reached. Use a more powerful cartridge if neces-
sary.
쎱쎱
7.3 Fastening with the tool
1. Press the tool firmly against the work surface at right
angles.
2. Fire the tool by pulling the trigger.
WARNING
Never attempt to drive a fastener in an existing hole
except where recommended by Hilti, e.g. when using
the DX X-BT system.
Never attempt to redrive the same fastener.
Never exceed the maximum fastener driving rate.
쎱쎱
7.4 X-FCM grating disc installation
1. Place the grating section.
2. Fasten the threaded stud into the steel frame. Using
the centering device will allow you to fasten perfect-
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
8
en
ly the stud in the middle. Check the penetration depth
with a gauge by measuring the standoff above the
surface fastened into (NVS)
3. Tighten the disc. Tightening torque = 5 to 8 Nm
쎱쎱
7.5 X-FCP checker plate installation
1. Plates must be pre-drilled or pre-punched.
2. Place and align the plate section.
3. Fasten the X-CRM threaded stud through the pre-
dilled hole. Check the penetration depth with a gauge
by measuring the standoff above the surface fastened
into (NVS)
4. Start the X-FCP on the stud by hand.
5. Tighten the plate. Tightening torque = 5 to 8 Nm
쎱쎱
7.6 Unloading the tool
Ensure that no cartridge strip or fastener is loaded in the
tool. Remove the cartridge strip by pulling it upwards
out of the tool and remove the fastener from the fastener
guide.
CAUTION
The tool can get hot while oper-
ating.
You could burn your hands.
Do not disassemble the tool while
it is hot. Let the tool cool down.
8. Care and maintenance
When this type of tool is used under normal operating
conditions, dirt and residues build up inside the tool
and functionally relevant parts are also subject to wear.
Regular inspections and maintenance are thus essen-
tial in order to ensure reliable operation. We recom-
mend that the tool is cleaned and the piston and piston
brake are checked at least weekly when the tool is sub-
jected to intensive use, and at the latest after driving
10,000 fasteners.
8.1 Care of the tool
The outer casing of the tool is manufactured from impact-
resistant plastic. The grip comprises a synthetic rubber
section.
The ventilation slots must be unobstructed and kept
clean at all times. Do not permit foreign objects to enter
the interior of the tool. Use a slightly damp cloth to clean
the outside of the tool at regular intervals. Do not use a
spray or steam-cleaning system for cleaning.
8.2 Maintenance
Check all external parts of the tool for damage at regu-
lar intervals and check that all controls operate proper-
ly. Do not operate the tool when parts are damaged or
when the controls do not operate properly. If necessary,
have the tool repaired at a Hilti service centre.
Servicing the tool
The tool should be serviced if:
1. Cartridges misfire
2. Fastener driving power is inconsistent
3. If you notice that:
contact pressure increases,
trigger force increases,
power regulation is difficult to adjust (stiff),
the cartridge strip is difficult to remove.
CAUTION while cleaning the tool:
Never use grease for maintenance/lubrication of tool
parts. This may strongly affect the functionality of the
tool. Use only Hilti spray or such of equivalent quality.
Dirt from DX tool contains substances that could be
endangering your health.
– Do not breath in the dust from cleaning
– Keep dust away from food
– Wash your hands after cleaning the tool
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
9
en
쎱쎱
8.3 Disassemble the tool
1. Ensure that no cartridge strip or fastener is loaded in
the tool. Remove the cartridge strip by pulling it
upwards out of the tool and remove the fastener from
the fastener guide.
2. Press the release button located at the side of the fas-
tener guide.
3. Unscrew the fastener guide.
4. Remove the buffer by bending it away from the fas-
tener guide.
5. Remove the piston.
쎱쎱
8.4 Check the buffer and piston for wear
Replace the buffer if:
the metal ring is loose or broken,
the buffer no longer holds on the fastener guide,
excessive, uneven wear beneath the metal ring is
noticed.
Replace the piston if:
it is broken,
the tip is heavily worn (i.e. a 90° segment is chipped
off),
piston rings are broken or missing,
it is bent (check by rolling on an even surface).
NOTE
Do not use worn pistons. Do not modify or grind pis-
tons.
쎱쎱
8.5 Check the fastener guide for wear
The nosepiece of the X-460-F8GR fastener guide should
be replaced if the tubular section is damaged (e.g. bent,
widened or cracked). For instructions on replacing the
nosepiece.
1. Ensure that no cartridge strip or fastener is loaded
in the tool. Remove the cartridge strip by pulling it
upwards out of the tool and remove the fastener
from the fastener guide
2. Press the release button on the side of the fastener
guide.
3. Unscrew the fastener guide from the tool
4. Check the buffer and piston for wear (see care and
maintenance instructions).
5. Pull the moveable ring downwards and unscrew the
fastener guide nosepiece
6. Replace the fastener guide nosepiece
7. Pull the moveable ring downwards and screw on
the fastener guide nosepiece
8. Push the piston into the tool as far as it will go
9. Press the buffer onto the fastener guide until it
engages
10. Push the fastener guide firmly onto the exhaust gas
piston return unit
11. Screw the fastener guide onto the tool until it engages.
쎱쎱
8.6 Clean the piston rings
1. Clean the piston rings with the flat brush until they
move freely.
2. Spray the piston rings lightly with Hilti spray.
쎱쎱
8.7 Clean the threaded section of the fastener guide
1. Clean the thread with the flat brush.
2. Spray the thread lightly with Hilti spray.
쎱쎱
8.8 Disassemble the piston return unit
1. Press the release button at the gripping part.
2. Unscrew the piston return unit.
쎱쎱
8.9 Clean the piston return unit
1. Clean the spring with the flat brush.
2. Clean the front end with the flat brush.
3. Use the small round brush to clean the two holes at
the end face.
4. Spray the piston return unit lightly with Hilti spray.
쎱쎱
8.10 Clean inside the housing
1. Use the large round brush to clean inside the hous-
ing.
2. Spray the inside of the housing lightly with Hilti spray.
쎱쎱
8.11 Clean the cartridge strip guideway
Use the scraper provided to clean the right and left car-
tridge strip guideways. The rubber cover must be lifted
slightly to facilitate cleaning of the guideway.
쎱쎱
8.12 Spray the power regulation wheel lightly with
Hilti spray
쎱쎱
8.13 Fit the piston return unit
1. Bring the arrows on the housing and on the exhaust
gas piston return unit into alignment.
2. Push the piston return unit into the housing as far as
it will go.
3. Screw the piston return unit onto the tool until it
engages.
쎱쎱
8.14 Assemble the tool
1. Push the piston into the tool as far as it will go.
2. Press the buffer onto the fastener guide until it snaps
into place.
3. Press the fastener guide firmly onto the piston return
unit.
4. Screw the fastener guide onto the tool until it engages.
8.15 Checking the tool following care and mainte-
nance
After carrying out care and maintenance on the tool,
check that all protective and safety devices are fitted
and that they function correctly.
NOTE
The use of lubricants other than Hilti spray could
damage rubber parts, especially the buffer.
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
10
en
Cartridge strip cannot be
removed
9. Troubleshooting
Cartridge not transported
Fault
Cause
Damaged cartridge strip
Carbon build up
Tool damaged
Tool overheated because of high
setting rate
Tool damaged
WARNING
Never attempt to pry a cartridge
from the magazine strip or tool.
Bad cartridge
Carbon build-up
WARNING
Never attempt to pry a cartridge
from the magazine strip or the tool.
Possible remedies
Change cartridge strip
Clean the cartridge strip guide-
way (see 8.11)
If the problem persists:
Contact Hilti Repair Centre
Let the tool cool down and then
carefully try to remove the
cartridge strip
If not possible:
Contact Hilti Repair Centre
Manually advance the cartridge
strip one cartridge
If the problem occurs more
often: Clean the tool
(see 8.3–8.14)
If the problem persists:
Contact Hilti Repair Centre
Tool is compressed too long
while fastening.
Fastening frequency is too high
Compress the tool less long
while fastening.
Remove the cartridge strip
Disassemble the tool (see 8.3)
for fast cooling and to avoid
possible damage
If the tool cannot be disassembled:
Contact Hilti Repair Centre
Cartridge strip melts
Cartridge cannot be fired
Cartridge falls out of the
cartridge strip
Fastening frequency is too high
WARNING
Never attempt to pry a cartridge
from the magazine strip or tool.
Immediately discontinue using
the tool and let it cool down
Remove cartridge strip
Let the tool cool down.
Clean the tool and remove loose
cartridge.
If it is impossible to disassemble
the tool:
Contact Hilti Repair Centre
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
11
en
Piston return unit is stuck
Carbon build-up Manually pull the front part of
the piston return unit out of the
tool
Check that the correct cartridges
are used (see 1.2) and that they
are in faultless condition.
Clean the tool (see 8.3–8.14)
If the problem persists:
Contact Hilti Repair Centre
Piston is stuck in the piston return
unit and cannot be removed
The operator notices:
– increased contact pressure
– increased trigger force
– power regulation stiff to adjust
– cartridge strip is difficult to
remove
Carbon build-up Clean the tool
(see 8.3–8.14)
Check that the correct cartridges
are used (see 1.2) and that they
are in faultless condition.
Damaged piston
Buffer debris inside the piston
return unit
Damaged buffer
Carbon build-up
Remove the cartridge strip and
clean the tool (see 8.3-8.14).
Check the piston and buffer and
replace these parts if necessary
(see 8.4).
If the problem persists:
Contact Hilti Repair Centre
Fault
Cause Possible remedies
Studs does not hold in base
material
Stud does not
penetrate
surface
Driving power too low
Application limit exceeded
(very hard surface)
Unsuitable system
Thin steel base material
(4 to 5 mm steel)
Try higher power setting or heav-
ier cartridge
Switch to more powerful system
like DX 76 PTR
Try different power setting or
different cartridge
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
12
en
Stud head penetrates through
material fastened
Stud breaks
Driving power too low
Application limit exceeded
(very hard surface)
Driving power too high
Try higher power setting or
heavier cartridge
Switch to more powerful system
like DX 76 PTR
Where permissible for the
application: predrill or change to
a different system (X-BT)
(please contact your Hilti sales
representative for further infor-
mation)
Reduce power setting
Use lighter cartridge
Fault
Cause Possible remedies
10. Disposal
Most of the materials from which Hilti power actuated tools are manufactured can be recycled. The materials
must be correctly separated before they can be recycled. In many countries, Hilti has already made arrange-
ments for taking back your old powder actuated tools for recycling. Please ask your Hilti customer service
department or Hilti sales representative for further information.
Should you wish to return the power actuated tool yourself to a disposal facility for recycling, proceed as fol-
lows: Dismantle the tools as far as possible without the need for special tools.
Separate the individual parts as follows:
Part / assembly Main material Recycling
Toolbox Plastic Plastics recycling
Outer casing Plastic / synthetic rubber Plastics recycling
Screws, small parts Steel Scrap metal
Used cartridge strip Plastic / steel According to local regulations
O.K.
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
13
en
11. Manufacturer's warranty – DX Tools
Hilti warrants that the tool supplied is free of defects
in material and workmanship. This warranty is valid so
long as the tool is operated and handled correctly,
cleaned and serviced properly and in accordance with
the Hilti Operating Instructions, and the technical sys-
tem is maintained. This means that only original Hilti
consumables, components and spare parts, or other
products of equivalent quality, may be used in the tool.
This warranty provides the free-of-charge repair or
replacement of defective parts only over the entire lifes-
pan of the tool. Parts requiring repair or replacement
as a result of normal wear and tear are not covered by
this warranty.
Additional claims are excluded, unless stringent
national rules prohibit such exclusion. In particular,
Hilti is not obligated for direct, indirect, incidental
or consequential damages, losses or expenses in
connection with, or by reason of, the use of, or inabil-
ity to use the tool for any purpose. Implied warranties
of merchantability or fitness for a particular purpose
are specifically excluded.
For repair or replacement, send tool or related parts
immediately upon discovery of the defect to the address
of the local Hilti marketing organization provided.
This constitutes Hilti's entire obligation with regard to
warranty and supersedes all prior or contemporane-
ous comments and oral or written agreements con-
cerning warranties.
13. CIP approval mark
The following applies to C.I.P. member states outside
the EU and EFTA judicial area:
The Hilti DX 460 has been system and type tested. As a
result, the tool bears the square approval mark showing
approval number S 812. Hilti thus guarantees compli-
ance with the approved type.
Unacceptable defects or deficiencies, etc. determined
during use of the tool must be reported to the person
responsible at the approval authority (PTB, Braun-
schweig)) and to the Office of the Permanent Interna-
tional Commission (C.I.P.) (Permanent Internationial
Commission, Avenue de la Renaissance 30, B-1000
Brussels, Belgium).
12. EC declaration of conformity (original)
Designation: Powder-actuated tool
Type: DX 460-GR
Year of design: 2001
We declare, on our sole responsibility, that this product
complies with the following directives and standards:
2006/42/EC, 2011/65/EU.
Hilti Corporation, Feldkircherstrasse 100,
FL-9494 Schaan
Norbert Wohlwend Tassilo Deinzer
Head of Quality & Processes Management Head BU Measuring Systems
BU Direct Fastening BU Measuring Systems
08/2012 08/2012
Technical documentation filed at:
Hilti Entwicklungsgesellschaft mbH
Zulassung Elektrowerkzeuge
Hiltistrasse 6
86916 Kaufering
Deutschland
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
14
en
14. Health and safety of the user
Noise information
Powder-actuated tool
Type: DX 460
Modell: Serial production
Caliber: 6.8/11 black
Power setting: 2
Application: Fastening 24 mm thick wood to concrete (C40)
with X-U 47P8
Declared measured values of noise characteristics according to 2006/42/EC Machinery Directive in
conjunction with E DIN EN 15895
Noise (power) level: L
WA, 1s
1
105 dB(A)
Emission noise-pressure level in the work station: L
pA, 1s
2
101 dB(A)
Peak sound pressure emission level: L
pC, peak
3
133 dB(C)
Operation and set-up conditions:
Set-up and operation of the pin driver in accordance with E DIN EN 15895-1 in the semi-anechoic test room of
Müller-BBM GmbH. The ambient conditions in the test room conform to DIN EN ISO 3745.
Testing procedure:
Enveloping surface method in anechoic room on reflective surface area in accordance with E DIN EN 15895, DIN
EN ISO 3745 and DIN EN ISO 11201.
NOTE: The noise emissions measured and the associated measurement uncertainty represent the upper limit for
the noise values to be expected during the measurements.
Variations in operating conditions may cause deviations from these emission values.
1
± 2 dB (A)
2
± 2 dB (A)
3
± 2 dB (C)
Vibration
The declared total vibration value according to 2006/42/EC does not exceed 2.5 m/s
2
.
Further information regarding the health and safety of the user can be found at the Hilti web site: www.hilti.com/hse
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
15
fr
NOTICE ORIGINALE
Appareil de scellement DX 460 GR
Pièces de l’appareil
@ Mécanisme de retour automatique du piston
; Douille de guidage
= Boîtier
% Guide d’entrée des cartouches
& Curseur (bouton) de déverrouillage de la molette de
réglage de puissance
( Molette de réglage de puissance
) Détente
+ Poignée
§ Bouton de déverrouillage du mécanisme du retour
automatique du piston
/ Ouïes d’aération
: Segments de piston
· Piston*
$ Canon interchangeable*
£ Bouton de déverrouillage du canon
| Amortisseur*
* Ces pièces peuvent être remplacées par l’utilisateur!
Sommaire Page
1. Consignes de sécurité 15
2. Consignes générales 17
3. Description 17
4. Accessoires 18
5. Caractéristiques techniques 20
6. Mise en marche 20
7. Utilisation 21
8. Nettoyage et entretien 22
9. Guide de dépannage 24
10. Recyclage 26
11. Garantie constructeur des appareils 27
12. Déclaration de conformité CE (original) 27
13. Marquage CIP 27
14. Santé de l'utilisateur et sécurité 28
Avant de mettre en marche l’appareil, lire
absolument son mode d’emploi.
Le présent mode d’emploi doit toujours
accompagner l’appareil.
Ne prêter ou céder l’appareil à quelqu’un
d’autre qu’en lui fournissant aussi le
mode d’emploi.
1. Consignes de sécurité
1.1 Consignes de sécurité fondamentales
Outre les consignes techniques de sécurité indiquées
dans les différents chapitres du présent mode d’em-
ploi, il a y lieu de toujours respecter strictement les
directives suivantes.
1.2 N'utiliser que des cartouches Hilti ou des cartou-
ches de qualité équivalente.
L'utilisation de cartouches de qualité moindre dans les
outils Hilti risque d'entraîner une accumulation de pou-
dre non consumée susceptible d'exploser subitement
et de causer de graves blessures aux opérateurs et aux
personnes alentour. Les cartouches doivent satisfaire
l'une des exigences minimales suivantes :
a) Leur fournisseur doit pouvoir confirmer le résultat
positif des essais conformément à la norme européen-
ne EN 16264
REMARQUE:
Toutes les cartouches pour appareils de scellement
ont été testées avec succès conformément à la nor-
me EN 16264.
Les contrôles définis par la norme EN 16264 sont des
tests des systèmes correspondant à des combinai-
sons spécifiques de cartouches et outils, qui sont
agréés par des organismes de certification.
La désignation de l'outil, le nom de l'organisme de
certification et le numéro du système sont imprimés
sur l'emballage de la cartouche.
ou
b) Elles doivent porter le marquage CE de conformité
(obligatoire dans l'UE à partir de juillet 2013)
Voir exemple d'emballage à l'adresse :
www.hilti.com/dx-cartridges
1.3 Utilisation conforme à l’usage prévu
L’appareil DX 460 est destiné aux utilisateurs profes-
sionnels dans l’industrie et l’artisanat de la construc-
tion (gros-oeuvre et second-oeuvre) qui veulent implan-
ter des clous, goujons ou éléments de fixation combi-
nés dans le béton, l’acier ou la brique silicocalcaire.
1.4 Utilisation abusive
Toutes manipulations ou modifications sur l’appa-
reil sont interdites.
L’appareil ne doit pas être utilisé dans une atmo-
sphère explosive ou inflammable, sauf s’il est agréé
pour cela.
Printed: 12.08.2013 | Doc-Nr: PUB / 5069840 / 000 / 02
1 / 1

dans d''autres langues