Firman P05703 Mode d'emploi

P/N:357745452 Rev:01

OWNER’S MANUAL

Read all safety precautions and instructions carefully

before operating equipment.

Ensure engine is stopped and level before performing

any maintenance or service.

IMPORTANT:

Record product information to reference when ordering parts or

obtaining warranty coverage.

Serial Number:

PORTABLE GENERATOR

MODEL NUMBER

P05703

Rev Level:00

DO NOT RETURN TO

STORE!

CALL US FIRST!

CUSTOMER HOTLINE

1-844-347-6261

FOR QUESTIONS OR SERVICE

INFORMATION

Purchase Date:

Table of Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Safety Precautions . . . . . . . . . . . . . . . . . . . . .2

Unpacking the Generator. . . . . . . . . . . . . . . .6

Parts Included. . . . . . . . . . . . . . . . . . . . . . . .6

Assembly . . . . . . . . . . . . . .. . . . . . . . . . . . . . . 7

Install the Wheel Kit . . . . . . . . . . . . . . . . . . 7

Install the Support Leg. . . . . . . . . . . . . . . . 7

Install the Handle. . . . . .. . . . . . . . . . . . . . . 7

. . . . . . . . . . . . . .8

Controls and Features. . . . . . . . . . . . . . . . . 9

Generator. . . . . . . . . . . . .. . . . . . . . . . . . . .9

Control Panel. . . . . . . . . . . . . . . . . . . . . . . 10

Remote Start. . . . . . . . . . . . . . . . . . . . . . . 11

Remote Control Programming . . . . . . . . 11

Specifications. . . . . . . . . . . . . . . . . . . . . . . . 12

Add Engine Oil . . . . . . . . . . . . . . . . . . . . . .13

Low Oil Shutdown . . . . . . . . . . . . . . . . . . .13

Add Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Operation at High Altitude . . . . . . . . . . .14

Grounding. . . . .. . . . . . . . . . . . . . . .. . . . . .15

System.. . . . . . . . . . . . . . . . . . . . . . .. . . . . .15

Operation . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 16

Generator Location . . . . . . . . . . . . . . . . . . 16

Surge Protection . . . . . . . . . . . . .. . . . . . . .16

Starting the Generator (Recoil Start) . . 17

Starting the Generator (Electric Start) .. 18

Starting the Generator (Remote Start) . 19

Connecting Electrical Loads . . . . . . . .. . . 20

Stopping the Engine . . . . . . . . . . . . . . . . . 20

Low Oil Shutdown . . . . . . . . . . . . . . . . . . 21

Do Not Overload Generator . . . . . . . . . . . 21

Introduction

Battery Cable Connection

Connecting to a Building’s Electrical

Maintenance And Storage. . . . . . . . . . . . . . 22

Maintenance Schedule . . . . . . . . . . . . . 22

Engine Maintenance .. . . . . . . . . . . .. . . . 23

Change Engine Oil . . .. . . . . . . . . . . . . . 23

Air Filter Maintenance. . . . . . . . . . . . . .23

Spark Plug Maintenance. . . . . . . . . . . . 24

Cleaning Fuel Strainer . . . . . . . . . . . . 24

. . . 24

Generator Maintenance . . . . . . . . . . . . . . 25

. . . . . . . . . . . . . . . 25

Service and Storage . . . . . . . . . . . . . . . .. 26

Trouble Shooting . . . . . . . . . . . . . . . . . . . . .27

Parts Diagram and Parts List . . . . . . . . . . 28

Generator Parts Diagram . . . . . . . . . . . . 28

Engine Parts Diagram . . . . . . . . . .. . . . . 29

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . 30

Service Information . . . . . . . . . . . . . .. . . . . 32

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Inspect Muffler and Spark Arrester

Battery Replacement

English Customer Service: 1-844-FIRMAN1

Thank you for purchasing a FIRMAN generator.

This manual covers operation and maintenance of the FIRMAN generators. All information in this

publication is based on the latest production information available at the time of approval for printing.

The manufacturer reserves the right to change, alter or other wise improve the generator and this

documentation at any time without prior change.

Page 01

This manual contains safety information to make you aware of the hazards and risks associated

with generator products and how to avoid them. This generator is designed and intended only

for supplying electrical power for operating compatible electrical lighting, appliances, tools and

motor loads, and is not intended for any other purpose. It is important that you read and

understand these instructions thoroughly before attempting to start or operate this equipment.

Save these original instructions for future reference.

Important Safety Information

The manufacturer cannot possibly anticipate every possible circumstance that might involve a

hazard. The warnings in this manual and the tags and decals affixed to the unit are therefore not

all-inclusive. If you use a procedure, work method or operating technique that the manufacturer

does not specifically recommend you must satisfy yourself that it is safe for you and others. You

must also make sure that the procedure work method or operating technique that you choose

does not render the generator unsafe.

SAFETY INFORMATION

DANGER WARNING CAUTION

DANGER indicates a

potentially hazardous

situation which, if not

avoided. WILL result in

death or serious injury.

WARNING indicates a

potentially hazardous

situation which, if not

avoided, could result in

death or serious injury.

CAUTION indicates a

potentially hazardous

situation which, if not

avoided, may result in minor

or moderate personal injury,

or property damage.

Toxic Fumes

Fire Hazard

Hot Surface.

Do Not Touch the Surface.

Kickback

Risk of Electric Shock

Explosion Hazard

Rotating Parts Entanglement

Hazard

Operator’s Manual

INTRODUCTION

English Customer Service: 1-844-FIRMAN1

SAFETY PRECAUTIONS

Page 02

WARNING

POISONOUS GAS HAZARD.

•

WARNING

•

English Customer Service: 1-844-FIRMAN1

Page 03

CORRECT USAGE

Example location to reduce risk of carbon monoxide poisoning

•

ONLY use outside and downwind, far away from windows, doors and vents.

•

Direct exhaust away from occupied spaces.

INCORRECT USAGE

Do not operate in any of the following locations:

Near any door, window or vent

Garage

Basement

Crawl Space

Living Area

Attic

Entry Way

Porch

Mudroom

English Customer Service: 1-844-FIRMAN1

Page 04

WHEN OPERATING EQUIPMENT

•

DO NOT tip engine or equipment at angle

which causes fuel to spill.

DO NOT stop engine by moving choke

control to “Start” position.

•

WHEN TRANSPORTING, MOVING

OR REPAIRING EQUIPMENT

Transport/move/repair with fuel tank

EMPTY or with fuel shutoff valve OFF.

•

DO NOT tip engine or equipment at angle

which causes fuel to spill.

Disconnect spark plug wire.

•

WHEN STORING FUEL OR EQUIPMENT

WITH FUEL IN TANK

•

WARNING

•

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

WARNING

•

NEVER start or stop engine with electrical

devices plugged in and turned on.

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire,

or explosion resulting in death or serious

injury and/or property damage.

WHEN ADDING OR DRAINING FUEL

Turn generator engine OFF and let it cool at

least 2 minutes before removing fuel cap.

Loosen cap slowly to relieve pressure in tank.

Fill or drain fuel tank outdoors.

•

DO NOT overfill tank. Allow space for fuel

expansion.

If fuel spills, wait until it evaporates before

starting engine.

•

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap, and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke.

•

WHEN STARTING EQUIPMENT

Ensure spark plug, muffler, fuel cap, and air

cleaner are in place.

•

DO NOT crank engine with spark plug

removed.

•

Use approved transfer equipment, suitable

for the intended use, to prevent backfeed by

isolating generator from electric utility

workers.

English Customer Service: 1-844-FIRMAN1

Page 05

WARNING

Unintentional sparking

could cause fire or

electric shock resulting

in death or serious

injury.

WHEN ADJUSTING OR MAKING REPAIRS TO

YOUR GENERATOR

Disconnect the spark plug wire from the

spark plug and place the wire where it cannot

contact spark plug.

•

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.

•

DO NOT check for spark with spark plug

removed.

•

WARNING

NEVER operate generator without protective

housing or covers.

DO NOT wear loose clothing, jewelry or

anything that could be caught in the starter

or other rotating parts.

Tie up long hair and remove jewelry.

•

DO NOT exceed the generator’s wattage

amperage capacity.

Start generator and let engine stabilize

before connecting electrical loads.

NOTE:

•

CAUTION

Exceeding generators wattage/amperage capacity

could damage generator and/or electrical devices

connected to it.

Connect electrical loads in OFF position,

then turn ON for operation.

Turn electrical loads OFF and disconnect

from generator before stopping generator.

•

DO NOT use generator with electrical cords

which are worn, frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or

wet weather.

DO NOT handle generator or electrical

cords while standing in water, while

barefoot, or while hands or feet are wet.

DO NOT allow unqualified persons or

children to operate or service generator.

•

WARNING

Exhaust heat/gases could ignite combustibles,

structures or damage fuel tank causing a fire,

resulting in death or serious injury and/or

property damage.

Contact with muffler area could cause burns

resulting in serious injury.

DO NOT touch hot parts and AVOID hot

exhaust gases.

Allow equipment to cool before touching.

It is a violation of California Public Resource

Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust

system is equipped with a spark arrester, as

defined in Section 4442, maintained in

effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester

designed for the exhaust system installed on

this engine.

Replacement parts must be the same and

installed in the same position as the original

parts.

•

When using generator for backup power,

notify utility company.

Use a ground fault circuit interrupter (GFCI)

in any damp or highly conductive area,

such as metal decking or steel work.

DO NOT touch bare wires or receptacles.

•

English Customer Service: 1-844-FIRMAN1

Page 06

•

Use generator only for intended uses.

If you have questions about intended use,

ask dealer or contact local service center.

Operate generator only on level surfaces.

DO NOT expose generator to excessive

moisture, dust, dirt, or corrosive vapors.

DO NOT insert any objects through cooling

slots.

If connected devices overheat, turn them off

and disconnect them from generator.

Shut off generator if:

-Electrical output is lost.

-Equipment sparks, smokes, or emits flames.

-Unit vibrates excessively.

•

WARNING

Medical and Life Support Uses.

In case of emergency, call 911 immediately.

NEVER use this product to power life support

devices or life support appliances.

NEVER use this product to power medical

devices or medical appliances.

Inform your electricity provider immediately

if you or anyone in your household depends

on electrical equipment to live.

Inform your electrical provider immediately

if a loss of power would cause you or anyone

in your household to experience a medical

emergency.

•

NOTE:

Improper treatment of generator could damage

it and shorten its life.

UNPACKING THE GENERATOR

•

Parts Included

Your gasoline powered generator ships with

the following parts:

1. Axle pin . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

2. 10.0" in. Wheel . . . . . . . . . . . . . . . . . . . . . . . . . 2

3. Flat Washer. . . . . . . . . . . . . . . .. . . . . . . . . . . . . .2

4. Cotter pin. . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . .2

5. Engine Oil(Bottle) . . . .. . . . . . . . . . . . . . . . . . . .1

6. Oil Funnel . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . 1

7. Wrench for Spark plug . . . . . . . . . . . . . . . . . . . .1

8. Double Open wrench (10mm & 12mm). . . . 2

9. Support Leg with Vibration Mounts . . . . . . 1

10. Flange Bolt (M8x16 for Support Leg) . . . . . 2

11. Flange Lock Nut (M8) . . . . . . . . . . . . . . . . . . . 4

12. Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 1

13. Flange Bolt (M8x50 for Handle) . . . . . . . . . 2

14. Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

15. Quick Reference Guide . . . . . . . . . . . . . . . . . 1

16. Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

16

English Customer Service: 1-844-FIRMAN1

12

11

13

Page 07

English Customer Service: 1-844-FIRMAN1

Install the Wheel Kit

The wheel kit is not intended for over-the-road

use.

Install the Support Leg

ASSEMBLY

Install the Handle

1. Place the handle K over the mounting channel

on the frame.

2. Secure the handle to the frame using the two

handle flange bolts H(M8x50).

3. Place a flange nut F (M8) on the end of each

bolt and fasten securely with provided

wrenches.

DO NOT over tighten the flange nuts.

A

B

C

F

The generator requires some assembly prior to

usage. If problems arise when assembling the

generator, call 1-844-347-6261.

F

E

G

H

K

1. Before adding wheels, tip the generator on

its side.

2. Slide the axle pin A through the wheel B.

3. Slide the axle pin A through the mount point

on the frame and flat washer D.

4. Secure the wheel and axle pin with the cotter

pin C.

5. Repeat steps 2-4 to attach another wheel.

1. Attach the support leg G to the generator

frame with flange bolts E (M8x16) and flange

lock nuts F(M8).

2. Tip the generator slowly so that it rests

on the wheels and support leg.

3.Tighten bolt E and nut F with provide

wrenches.

CAUTION

D

Page 08

Battery Cable Connection

NOTE:

The generator comes equiped with the positive red cable(red cable) already attached.

1. Verify the positive (+) battery cable (red boot) is securely tightened to the positive (+) battery

post. Make sure boot is over battery post.

2. Remove bolt M5X12 and M5 nut from black cable ring.

English Customer Service: 1-844-FIRMAN1

3. Remove vinyl cap from the negative(-) battery post. Locate negative (-) black cable and route

to the negative(-) battery post. Tight the cable with bolt M5X12 and M5 nut. Cover the post with

black boot.

M5X12

M5

Black Cable

Ring

Black Boot

Red Cable(+)

Black Cable(-)

-

+

You will need to use 8mm box wrenches to connect the battery cables to battery.

Page 09

CONTROLS AND FEATURES

Generator

1- Fuel Gauge

2- 8.0 Gallon Capacity Fuel Tank

3- Fuel Cap

4- Choke Lever(behind air filter box)

5- Fuel Valve

6- Air Filter

7- 389cc FIRMAN OHV Engine

8- Recoil Starter

9- 10.0" Flat Free Wheel

10- Oil Filler Cap

11- Outlet Cover

12- Control Panel

13- Handle

14- Battery

English Customer Service: 1-844-FIRMAN1

*We are always working to improve our products. Therefore, the enclosed product may differ

slightly from the image on this page.

1

2

①

②

③

⑤

⑥

⑦

⑧

⑨

⑩

⑪

⑫

⑬

⑭

④

1

2

4-1 Data-Minder(Multi-Meter) – Push the

SELECT button to show the Voltage, Hertz and

running hours. If the low oil indicator is lit,

check the oil level.

3

4

5

7

Ground Terminal – Consult an electrician

for local grounding regulations.

Battery Switch – Power the electric starter.

8

9

Outlet Cover - Protect the receptacles from

dust and debris.

10

11

Page 10

NOTE:

Total power drawn from all receptacles must not exceed the name plate rating.

Engine Start Switch – Used to start engine

from the starter motor(Electric start model

only). To start engine, press and hold the

switch in the “START”(ll) position, the

engine will crank and attempt to start. When

the engine starts, release the switch to the

“RUN”(l) position.

Control Panel

A - Digital display

B - AC voltage indicator

C - Frequency indicator

D - Hour indicator

E - Low oil indicator

F - Select button

English Customer Service: 1-844-FIRMAN1

2

3

4

5

6

7

8

9

10

11

1

6

120V, 30A Twist-Lock (NEMA L5-30R)

120/240V, 30A Twist-Lock – (NEMA L14-30R)

120V, 20A Duplex – (NEMA 5-20R)

30 Amp current may be drawn from this 120 Volt

receptacle.

Remote Start Indicator Light - The light

will light or flash depending on the status of

the remote start system.

Remote Start Program Button - Use this

button along with the remote control to program

the generator to be started remotely. Your remote

control is already programmed in factory for your

convenience. You might need programming when

using new remote control.

Maximum full load current may be drawn from this

120/240 Volt, 30 Amp receptacle.

11

20 Amp current may be drawn from this 120 Volt

receptacle.

Page 11

Remote Start

This generator is equipped with a wireless remote

start system for starting and stopping.

The Remote Start functions are enabled when:

1.The Engine Switch is in the “RUN”(l) position, AND

2.The Battery Switch is in the “ON”(l) position.

The Remote Start functions are disabled if either

of the above conditions is not met.

Remote Control Power Consumption

THE BATTERY SWITCH ALWAYS SHOULD BE IN

"OFF"(O) POSITION AT THE END OF USE TO

PREVENT BATTERY DRAIN.

NOTE:

English Customer Service: 1-844-FIRMAN1

While the Engine Switch is in the “RUN”(l)

position and Battery Switch is in the “ON”(l)

position, the remote module is active and

waiting for a remote signal. This function

requires electrical current from the battery.

If the Battery Switch is left in the “ON”(l)

position for extended periods the battery can

be completely drained.

Remote Control Programming

1. Flip the engine switch to the "RUN"(l) position.

NOTE:

YOUR REMOTE CONTROL IS ALREADY PROGRAMMED IN

FACTORY FOR YOUR CONVENIENCE. AND IT IS READY TO

START THE GENERATOR.

Before the generator can be started , an initial

start-up procedure must be performed so the

generator and the remote control recognize

each other.

If the remote control is replaced then you will

need to go through following procedure with

new remote control.

2. Flip the battery switch to the "ON"(l) position.

3. Push and hold the program button on the

control panel for approximately 3 seconds. The

remote start indicator light will light.

Indicator

Light

Program Button

4. Push and release the ''STOP'' button on the

remote control. The indicator light will flash

once to erase the remote program.

STOP

5. Push and release the ''START'' button. The

indicator light will flash once to program the

remote.

START

6. Push and hold the program button approximately

3 seconds until the indicator light turn off. The

generator is now programmed to start remotely.

Page 12

SPECIFICATIONS

AN IMPORTANT MESSAGE ABOUT TEMPERATURE:

When operated above 77°F(25°C) there may be a decrease in power.

Maximum wattage and current are subject to and limited by such factors as fuel BTU content

ambient temperature, altitude, engine condition and etc. Maximum power decreases about

3.5% for each 1,000 feet above sea level; and will also decrease about 1% for each 10°F(-12.2°C)

above 60°F(16°C) ambient temperature.

•

English Customer Service: 1-844-FIRMAN1

Model

Rated AC Voltage

Phase

Power Factor

Voltage Regulator

Alternator Type

Running Watts

Starting Watts

Engine

Engine Type

Displacement

Low Oil Shutdown

Ignition System

Starting System

Fuel

Capacity Fuel Tank

Lubricating Oil Capacity

Carburetor Type

Air Cleaner

P.T.O. Shaft Rotation

120/240V

P05703

5700

AVR

Single

1

Single Cylinder, 4-Stroke OHV Air Cooled

389cc

Breakless Ignition Type, Flywheel Magneto

Unleaded Automotive Gasoline

8.0 Gallon

37.2 oz(1.1L)

Counter Clockwise (Facing P.T.O.)

Float

Brushed

Polyurethane Type

Yes

7125

FIRMAN

Rated Fequency

60Hz

Oil Type

See “Add Engine Oil” Section

Spark Plug

TORCH F6RTC/NGK BPR6ES/CHAMPION RN9YC

Recoil/Electric Start/Remote Start

ADD ENGINE OIL

Page 13

1.Place generator on a flat, level surface.

2.Clean area around oil fill and remove yellow

oil fill cap/dipstick.

3.Wipe dipstick clean.

NOTE:

The engine is equipped with a low oil shut-off and

will stop when the oil level in the crankcase falls

below the threshold level.

NOTE:

We consider the first 5 hours of run time to be

the break-in period for the unit. During the break

in period stay at or below 50% of the running

watt rating and vary the load occasionally to allow

stator windings to heat and cool. Adjusting the

load will also cause engine speed to vary and help

seat piston rings.

CAUTION

The unit is equipped with a low oil shutdown.If

the oil level becomes lower than required,the

sensor will activate a warning device or stop the

engine.

If generator shuts off and the oil level is within

specifications, check to see if generator is sitting

at an angle that forces oil to shift. Place on an

even surface to correct this. If engine fails to

start, the oil level may not be sufficient to

deactivate low oil level switch. Make sure the

sump is completely full of oil.

(H)

DRAIN PLUG

(L)

5.Replace oil fill cap/dipstick and fully tighten.

6.Oil level should be checked prior to each use

or at least every 8 hours of operation. Keep oil

level maintained.

4.Using oil funnel, slowly pour contents of

provided oil bottle into oil fill opening to the

"H" mark on dipstick. Be careful do not

overfill. Overfilling with oil could cause the

engine to not start or hard starting.

Low Oil Shutdown

Degrees Celsiusº(Outside)

Full Synthetic 5W-30

Degrees Fahrenheitº(Outside)

5W-30 10W-40

10W-30

CAUTION

H

L

English Customer Service: 1-844-FIRMAN1

ADD FUEL

Page 14

Fuel must meet these requirements:

•

Clean, fresh, unleaded gasoline.

Use regular UNLEADED gasoline with the

generator engine with a minimum 87 octane

/ 87 AKI (91 RON).

For high altitude use, see "Operation at High

Altitude".

Do not use gasoline with more than 10%

alcohol such as E85 or ethanol.

•

Failure to follow Operator's Manual for fuel

recommendations voids warranty.

Avoid generator damage.

DO NOT use unapproved gasoline such as E85.

DO NOT mix oil in gasoline.

DO NOT modify engine to run on alternate fuels.

•

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire or

explosion resulting in death, serious injury

and/or property damage.

WHEN ADDING FUEL

Fill fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel

expansion. If the tank is overfilled, fuel

can overflow onto a hot engine and cause fire

or explosion. Wipe up any spilled fuel

immediately.

If fuel spills, wait until it evaporates before

starting engine.

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke when

filling the fuel tank.

•

1.Clean area around fuel fill cap, remove cap.

2.Slowly add unleaded fuel to fuel tank. Be

careful not to fill above the red fuel level

indicator . This allows adequate space for

fuel expansion.

3.Install fuel cap and let any spilled fuel

evaporate before starting engine or wipe up

any spilled gasoline.

CAUTION

Slowly add unleaded gasoline to fuel tank.

Do not overfill tank.

Do not fill above top of fuel screen. This

will all expansion in hot weather and

prevent overflow.

•

Operation at High Altitude

At altitudes over 5,000 feet(1524 meters), a

minimum 85 octane / 85 AKI (89 RON) gasoline

is acceptable.

The density of air at high altitude is lower

than at sea level. Engine power is reduced

as the air mass and air-fuel ratio decrease.

Engine power and generator output will be

reduced approximately 3.5% for every 1000 feet

of elevation above sea level. This is a

natural trend and cannot be changed by

adjusting the engine. At high altitudes

increased exhaust emissions can also result

due to the increased enrichment of the air

fuel ratio.

Other high altitude issues can include hard

starting, increased fuel consumption and

spark plug fouling. To alleviate high

altitude issues other than the natural

power loss, FIRMAN can provide a high

altitude carburetor main jet. The alternative

English Customer Service: 1-844-FIRMAN1

Page 15

Altitude main jet 1

Altitude main jet 2

389cc

357717002

357717003

Altitude

3000-6000Feet

6000-8000Feet

OPEN

WARNING

Grounding

The National Electric Code requires your generator

must be properly connected to an appropriate

ground to help prevent electric shock.

Failure to properly ground the

generator can result in electric

shock.

WARNING

THERE IS A PERMANENT CONDUCTOR BETWEEN

THE GENERATOR (STATOR WINDING) AND THE

FRAME.

Use approved transfer equipment to prevent

backfeed by isolating generator from electric

utility workers.

When using generator for backup power, notify

utility company.

Use a ground fault circuit interrupter (GFCI) in

any damp or highly conductive area, such as

metal decking or steel work.

DO NOT touch bare wires or receptacles.

DO NOT use generator with electrical cords

which are worn,frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or wet

weather.

DO NOT handle generator or electrical cords

while standing in water, while barefoot, or

while hands or feet are wet.

DO NOT allow unqualified persons or children

to operate or service generator.

Connecting to a Building's Electrical System

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

The part number and recommended minimum

altitude for the application of the high

altitude carburetor main jet is listed in the

table below.

main jet and installation instructions can be

obtained by contacting Customer Support.

Installation instructions are also available in the

Technical Bulletin area of the FIRMAN internet site.

English Customer Service: 1-844-FIRMAN1

5. OPERATION

Page 16

Generator Location

Make sure you review each warning in order to

prevent fire hazard.

Keep area clear of inflammables or other

hazardous materials.

Select a site that is dry, well ventilated and

protected from the weather.

Keep exhaust pipe clear of foreign objects.

Keep generator away from open flame.

Keep generator on a stable and level surface.

WARNING

Surge Protection

Voltage fluctuation may impair the proper

functioning of sensitive electronic equipment.

WARNING

POISONOUS GAS HAZARD.

•

Do not block generator air vents with paper or

other material.

CAUTION

Tilting can cause fuel spillage.

CAUTION

English Customer Service: 1-844-FIRMAN1

Page 17

Starting the Generator (Recoil Start)

1. Before starting the generator, check for loose

or missing parts and for any damage which

may have occurred during shipment.

2. Check oil level and fuel.

7. Move the choke lever to the “START” position.

5. Flip the engine switch to the “RUN(l)” position.

9. Do not over-choke. As soon as engine starts

and warms up, move the choke lever to the

“RUN” position.

10. Allow generator to run at no load for few

minutes upon each initial start-up to permit

engine and generator to stablize.

WARNING

When starting engine, pull cord slowly until

resistance is felt and then pull rapidly to avoid

kickback.

4. Turn the fuel valve to the “ON” (l)position.

8. Pull the starter cord slowly until resistance is

felt and then pull rapidly.

3. Disconnect all electrical loads from the

generator. Never start or stop the generator

with electrical devices plugged in or turned

on.

English Customer Service: 1-844-FIRMAN1

Keep choke lever in “START” position for only 1

pull of the recoil starter. After first pull, move

choke lever to the “RUN” position for up to the

next 3 pulls of the recoil starter. Too much

choke leads to sparkplug fouling/engine

flooding due to the lack of incoming air. This

will cause the engine not to start.

6. Flip the battery switch to the "ON"(l) position.

Page 18

Starting the Generator (Electric Start)

Electric Start and Remote Start Operations

WARNING

1. Before starting the generator, check for loose

or missing parts and for any damage which

may have occurred during shipment.

2. Check oil level and fuel.

3. Disconnect all electrical loads from the

generator. Never start or stop the generator

with electrical devices plugged in or turned on.

4. Turn the fuel valve to the “ON” (l)position.

5. Flip the engine switch to the "RUN"(l) position.

6. Flip the battery switch to the "ON"(l) position.

7. Move the choke lever to the “START” position.

8. Press and hold the engine switch in the "START"(ll)

position for few seconds and release the switch to the

"RUN"(l) position.

English Customer Service: 1-844-FIRMAN1

La page charge ...

Firman P05703 Mode d'emploi

Firman P05703 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents