Bosch 1617EVSPK Wood 12 Amp Router Tool Combo Kit Manuel utilisateur

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

Operating/Safety Instructions

Consignes de fonctionnement/sécurité

Instrucciones de funcionamiento y seguridad

1617

1617EVS

1617EVSPK

1618EVS

For English Version Version française Versión en español

See page 2 Voir page 25 Ver la página 48

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

Call Toll Free for

Consumer Information

& Service Locations

Pour obtenir des informations

et les adresses de nos centres

de service après-vente,

appelez ce numéro gratuit

Llame gratis para

obtener información

para el consumidor y

ubicaciones de servicio

2

1

0

IN

50

40

30

20

10

0

MM

2610051825.qxp_1617 5/24/18 12:53 PM Page 1

-2-

Work area safety

Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

Electrical safety

Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of

electric shock.

Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk

of electric shock if your body is earthed or

grounded.

Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

If operating a power tool in a damp location

is unavoidable, use a Ground Fault Circuit

Interrupter (GFCI) protected supply. Use of

an GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention

while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the

switch is in the off-position before

connecting to power source and / or battery

pack, picking up or carrying the tool.

Carrying power tools with your finger on the

switch or energizing power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before

turning the power tool on. A wrench or a

key left attached to a rotating part of the

power tool may result in personal injury.

Do not overreach. Keep proper footing and

balance at all times. This enables better

control of the power tool in unexpected

situations.

Dress properly. Do not wear loose clothing

or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose

clothes, jewelry or long hair can be caught in

moving parts.

If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce dust-

related hazards.

Power tool use and care

Do not force the power tool. Use the

correct power tool for your application. The

correct power tool will do the job better and

safer at the rate for which it was designed.

Do not use the power tool if the switch does

not turn it on and off. Any power tool that

cannot be controlled with the switch is

dangerous and must be repaired.

Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

!

WARNING

General Power Tool Safety Warnings

2610051825.qxp_1617 5/24/18 12:53 PM Page 2

Safety Rules for Routers

Hold power tool by insulated gripping

surfaces, because the cutter may contact

hidden wiring or its own cord. Contact with

a ”live” wire will make exposed metal parts of

the tool ”live” and shock the operator.

Use clamps or another practical way to

secure and support the workpiece to a

stable platform. Holding the work by your

hand or against the body leaves it unstable

and may lead to loss of control.

Do not drill, fasten or break into existing

walls or other blind areas where electrical

wiring may exist. If this situation is

unavoidable, disconnect all fuses or circuit

breakers feeding this worksite.

Always make sure the work surface is

free from nails and other foreign objects.

Cutting into a nail can cause the bit and the

tool to jump and damage the bit.

Never hold the workpiece in one hand and

the tool in the other hand when in use.

Never place hands near or below cutting

surface. Clamping the material and guiding

the tool with both hands is safer.

Never lay workpiece on top of hard

surfaces, like concrete, stone, etc...

Protruding cutting bit may cause tool to jump.

Always wear safety goggles and dust

mask. Use only in well ventilated area.

Using personal safety devices and working in

safe environment reduces risk of injury.

After changing the bits or making any

adjustments, make sure the collet nut and

any other adjustment devices are

securely tightened. Loose adjustment

device can unexpectedly shift, causing loss

of control, loose rotating components will be

violently thrown.

Never start the tool when the bit is

engaged in the material. The bit cutting

edge may grab the material causing loss of

control of the cutter.

Always hold the tool with two hands

during start-up. The reaction torque of the

motor can cause the tool to twist.

The direction of feeding the bit into the

material is very important and it relates to

the direction of bit rotation. When viewing

the tool from the top, the bit rotates

clockwise. Feed direction of cutting must

be counter-clockwise. NOTE: inside and

outside cuts will require different feed

direction, refer to section on feeding the

router. Feeding the tool in the wrong

direction, causes the cutting edge of the bit

to climb out of the work and pull the tool in

the direction of this feed.

-3-

Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools. Check for misalignment

or binding of moving parts, breakage of

parts and any other condition that may

affect the power tool’s operation. If damaged,

have the power tool repaired before use.

Many accidents are caused by poorly

maintained power tools.

Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

Use the power tool, accessories and tool

bits etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

Service

Have your power tool serviced by a qualified

repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

2610051825.qxp_1617 5/24/18 12:53 PM Page 3

Never use dull or damaged bits. Sharp

bits must be handled with care. Damaged

bits can snap during use. Dull bits require

more force to push the tool, possibly causing

the bit to break.

Never touch the bit during or immediately

after the use. After use the bit is too hot to

be touched by bare hands.

Never lay the tool down until the motor

has come to a complete standstill. The

spinning bit can grab the surface and pull the

tool out of your control.

Never use bits that have a cutting

diameter greater than the opening in the

base.

The rated speed of the accessory must be

at least equal to the maximum speed

marked on the power tool. Accessories

running faster than their RATED SPEED can

break and fly apart.

-4-

Additional Safety Warnings

GFCI and personal protection devices like

electrician’s rubber gloves and footwear will

further enhance your personal safety.

Do not use AC only rated tools with a DC

power supply. While the tool may appear to

work, the electrical components of the AC

rated tool are likely to fail and create a hazard

to the operator.

Keep handles dry, clean and free from oil

and grease. Slippery hands cannot safely

control the power tool.

Use clamps or other practical way to secure

and support the workpiece to a stable

platform. Holding the work by hand or against

your body leaves it unstable and may lead to

loss of control.

Develop a periodic maintenance schedule

for your tool. When cleaning a tool be

careful not to disassemble any portion of

the tool since internal wires may be

misplaced or pinched or safety guard return

springs may be improperly mounted.

Certain cleaning agents such as gasoline,

carbon tetrachloride, ammonia, etc. may

damage plastic parts.

Risk of injury to user. The power cord must only

be serviced by a Bosch Factory Service Center

or Autho rized Bosch Service Station.

Some dust created by power

sanding, sawing, grinding,

drilling, and other construction activities

contains chemicals known to cause cancer,

birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and

other masonry products, and

• Arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area, and

work with approved safety equipment, such as

those dust masks that are specially designed

to filter out microscopic particles.

!

WARNING

2610051825.qxp_1617 5/24/18 12:53 PM Page 4

-5-

Read and understand the tool manual and

these instructions for the use of this table

with your router. Failure to follow all

instructions listed below may result in serious

personal injury.

Unplug tool before setting up in table,

making adjustments or changing bits.

Accidental start-up of the tool can cause

injury.

Fully assemble and tighten all the

fasteners required for this table and

mounting the router. Also remember to

occasionally check the stand and make sure

it is still tight. A loose stand is unstable and

may shift in use and cause serious injury.

Before operating make sure the entire

unit is placed on a solid, flat, level

surface. Serious injury could occur if tool is

unstable and tips.

Never stand on the table or use as ladder

or scaffolding. Serious injury could occur if

the table is tipped or the cutting tool is

accidentally contacted. Do not store

materials on or near the table such that it is

necessary to stand on the table or its stand

to reach them.

Never use dull or damaged bits. Sharp

bits must be handled with care. Damaged

bits can snap during use. Dull bits require

more force to push the workpiece, possibly

causing the bit to break.

Match the appropriate bit and its speed to

your application. Do not use bits that

have a cutting diameter that exceeds the

capacity of the tool. Overloading the tool

can lead to personal injury or tool failure.

Never start the tool when the bit is

engaged in the material. The bit cutting

edge may grab the material causing loss of

control of the workpiece.

Router bits are intended for wood, wood

products and plastic only. Be sure the

workpiece does not contain nails, etc.

before routing. Cutting a nail or the like will

cause the carbides to be dislodged, fly

toward the operator side, and possibly strike

you or bystanders.

Feed the workpiece against the rotation of

the bit. The bit rotates counter-clockwise

as viewed from the top of table. Feeding

the work in the wrong direction will cause the

workpiece to "climb" up on the bit and may

lead to loss of control during operation.

Never place hands near the spinning bit.

Use push sticks, vertical and horizontally

mounted feather boards (spring sticks)

and other jigs to hold down the workpiece

and keep your hands away from the

spinning bit. Router cuts are blind cuts but

the bit still protrudes through the table and

you must be aware of the position of your

hands relative to the spinning bit.

We do not recommend cutting material

that is warped, wobbly or otherwise

unstable. If this situation is unavoidable

always cut the material with the concave

side against the table. Cutting the material

with the concave side up or away from table

may cause the warped or wobbly material to

roll; causing you to lose control, kickback and

serious personal injury may result.

Use the adjustable fence in straight

cutting applications. When routing along

an entire edge of the work, the fence, fence

faces, and adjustable outfeed fence support

shims will help maintain stability.

When the table is used without the fence,

piloted bits (or "bearing bits") must be

used. Piloted bits are used when routing

internal and external contours on a

workpiece. The bearing of the piloted bit

assists in maintaining control of the

workpiece. Whenever possible, the starter

pin should also be used.

After changing the bits or making any

adjustments, make sure the collet nut and

any other adjustment devices are

securely tightened. Loose adjustment

device can unexpectedly shift, causing loss

of control, loose rotating components will be

violently thrown.

Never touch the bit during or immediately

after the use. Contact with a spinning bit

will cause injury and after use the bit is too

hot to be touched by bare hands.

Use only Bosch replacement parts. Any

others may create a hazard.

Safety Rules for Router Table

2610051825.qxp_1617 5/24/18 12:53 PM Page 5

-6-

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Diameter Size of drill bits, grinding wheels, etc.

n0 No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

.../min Revolutions or reciprocation Revolutions, strokes, surface speed,

per minute orbits etc. per minute

0 Off position Zero speed, zero torque...

1, 2, 3, ... Selector settings Speed, torque or position settings.

I, II, III, Higher number means greater speed

Infinitely variable selector with off Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction Designates Double Insulated

Construction tools.

Earthing terminal Grounding terminal

Warning symbol Alerts user to warning messages

Li-ion RBRC seal Designates Li-ion battery recycling

program

Ni-Cad RBRC seal Designates Ni-Cad battery recycling

program

Read manual symbol Alerts user to read manual

Wear eye protection symbol Alerts user to wear eye protection

Symbols

0

2610051825.qxp_1617 5/24/18 12:53 PM Page 6

-7-

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is listed by the Canadian Standards

Association.

This symbol designates that this tool is listed by the Canadian Standards

Association, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

Symbols (continued)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

This symbol designates that this component is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters Laboratories,

to United States and Canadian Standards.

2610051825.qxp_1617 5/24/18 12:53 PM Page 7

-8-

Functional Description and Specifications

Disconnect the plug from the power source before making any

assembly, adjustments or changing accessories. Such preventive safety

measures reduce the risk of starting the tool accidentally.

!

WARNING

FIG. 1

SPEED CONTROL DIAL

Models 1617EVS

& 1618EVS only

SUB-BASE

TRIGGER

SWITCH

"LOCK-ON"

BUTTON

D-HANDLE

ROUND

HANDLE

BASE CLAMP LEVER

CHIP DEFLECTOR

MOTOR HOUSING

ROCKER ON\OFF

SWITCH

POWER ON/OFF

SWITCH

TEMPLET GUIDE

QUICK CHANGE LEVER

(Not included, available as

accessory)

MOTOR ALIGNMENT

ARROW

FIG. 2

AIR VENTS

REVERSIBLE

HANDLE

BIT ROTATION ARROW

Routers

BASE TYPE S

BASE TYPE D

1617EVS

1618EVS

SPEED CONTROL DIAL

Models 1617EVS

& 1618EVS only

TEMPLET GUIDE

QUICK CHANGE LEVER

(Not included, available as accessory)

2610051825.qxp_1617 5/24/18 12:53 PM Page 8

-9-

2

1

0

IN

50

40

30

20

10

0

MM

FIG. 3

SPEED CONTROL DIAL

Model 1617EVSP only

SUB-BASE

PLUNGE HANDLE

CHIP DEFLECTOR

MOTOR HOUSING

ROCKER ON\OFF SWITCH

MOTOR

ALIGNMENT ARROW

AIR VENTS

BIT ROTATION ARROW

BASE TYPE P

Collet capacities 1/4", 3/8", 1/2", 8mm

NOTE: For tool specifications refer to the nameplate on your tool.

RA1161 fixed-base shop router base marked type "S" is designed for use with these router motors:

1617 router motor (16171)

1617EVS router motor (16176)

1618EVS router motor (16186)

RA1162 D-handle router base marked type "D" is designed only for use with these router motors:

1618EVS router motor (16186)

RA1166 plunge router base marked type "P" is designed for use with these router motors:

1617 router motor (16171)

1617EVS router motor (16176)

1618EVS router motor (16186)

PLUNGE LOCK

LEVER

DEPTH ROD

DEPTH ROD KNOB

DEPTH STOP TURRET

DEPTH INDICATOR

DEPTH ROD FINE

ADJUSMENT KNOB

1617EVSPK

2610051825.qxp_1617 5/24/18 12:53 PM Page 9

-10-

Assembly

A wide assortment of router bits with different

profiles is available separately. Use 1/2"

shank whenever possible, and only use good

quality bits.

To prevent personal injury,

always remove the plug

from power source before removing or

installing bits or accessories.

INSTALLING A ROUTER BIT

Place router upside down or lay router on its

side with the base resting on the bench.

Another option is to remove the motor from

the base before installing the bit.

1. Remove the chip shield (or flip up if plunge

base is attached.

2. Hold the armature shaft in place with the

shaft wrench (Fig. 4)

3. Next, use the collet wrench to loosen the

collet chuck assembly in counter-

clockwise direction (viewed from under the

router).

4. Once you have verified that the bit's shank

is of the proper diameter for the collet to

be used, insert the shank of the router bit

into the collet chuck assembly as far as it

will go, then back the shank out until the

cutters are approximately 1/8" to 1/4" away

from the collet nut face.

5. With the router bit inserted and the shaft

wrench holding the armature shaft, use the

collet wrench to firmly tighten the collet

chuck assembly in a clockwise direction

(viewed from under the router). To ensure

proper gripping of the router bit and

minimize run-out, the shank of the router

bit must be inserted at least 5/8".

To tighten or loosen collet nut, hold both

wrenches in one hand and and squeeze

the wrenches together.

When the templet guide

has been removed from

base, do not use router bits greater than

2" in diameter as they will not fit through

the sub-base.

Cutter diameter must be at

least 1/4” smaller than

opening for the bit and cutter.

To prevent damage to

tool, do not tighten collet

without a bit.

NOTE: The bit shank and chuck should be

clean and free of dust, wood, residue and

grease before assembling.

REMOVING THE ROUTER BIT

1. Use the shaft and collet chuck wrenches

as described earlier, and turn the collet

chuck assembly in a counter-clockwise

direction.

2. Once the collet chuck assembly is

loosened continue to turn the collet chuck

assembly until it pulls the collet free from

its taper, and the router bit can be

removed.

NOTE: The collet chuck is self-extracting; it

is NOT necessary to strike the collet chuck to

free the router bit.

!

WARNING

COLLET CHUCK CARE

With the router bit removed, continue to turn

the collet chuck counter-clockwise until it is

free of the shaft. To assure a firm grip,

occasionally blow out the collet chuck with

compressed air, and clean the taper in the

armature assembly shaft with a tissue or fine

brush. The collet chuck is made up of two

component parts as illustrated (Fig. 5); check

to see that the collet is properly seated in the

collet chuck nut and lightly thread the collet

chuck back onto the armature shaft. Replace

worn or damaged collet chucks immediately.

COLLET

NUT

FIG. 5

COLLET

CHUCK

!

WARNING

!

CAUTION

!

WARNING

SHAFT

WRENCH

COLLET

WRENCH

FIG. 4

2610051825.qxp_1617 5/24/18 12:53 PM Page 10

REMOVING MOTOR FROM BASE (Fig. 6)

To remove motor from non-plunge bases:

1. Hold router in horizontal position, open base

clamp lever, depress coarse adjustment

lever, and pull motor upwards until it stops.

2. Turn motor counter-clockwise, and gently

pull it free of base.

To remove motor from plunge base: (Fig. 7)

1. Hold router in horizontal position, open base

clamp lever, and pull motor upwards until it

stops.

2. Turn motor counter-clockwise, and gently

pull it free of base.

INSTALLING MOTOR IN BASE

The motor can be installed with the switch

positioned on the right or left of the base from

the operator's side (and the cord facing the

opposite side of the router). Install the motor so

that the switch is in the location you find to be

the most easily accessible from the handles.

The switch should be easier to turn "OFF" than

"ON" in case of an emergency.

To install motor in non-plunge base:

1. Release the base clamp lever.

2. Line up the arrow on the base with arrow on

the motor. (Fig. 8)

• To position switch on the right side of the

base, line up the base’s arrow with motor

housing’s arrow that is below the cord.

• To position switch on the left, line up the

base’s arrow with motor housing’s arrow

that is below the switch.

3. While pressing the coarse adjustment lever,

slide motor into base until resistance in felt.

(The base’s guide pin is now engaged into

slot on motor.)

4. Continue to press coarse adjustment lever,

and turn the motor clockwise until it stops.

5. Push the motor into the base until it reaches

the approximate desired depth.

6. Release the coarse adjustment lever and

slide the motor forward or back as needed

until the coarse adjustment system’s “catch”

springs into the coarse adjustment detent

notch.

7. Set final height position as described below

in “Operating Instructions”.

To install motor in plunge base:

1. Release the base clamp lever.

2. Line up the arrow on the base with arrow on

the motor. (Fig. 8)

• To position switch on the right side of the

base, line up the base’s arrow with arrow

on the motor housing that is below the

cord.

• To position switch on the left, line up the

base’s arrow with arrow on the motor

housing that is below the switch.

3. Slide motor into base until resistance in felt.

(The base’s guide pin is now engaged into

slot on motor.)

4. Turn the motor clockwise until it stops.

5. Push the motor into the base as far as it will

go.

6. Fasten the base clamp lever.

-11-

ALIGNMENT

ARROWS

COARSE

ADJUSTMENT

NOTCHES

MOTOR

BASE

FIG. 8

BASE CLAMP LEVER

FIG. 6

COARSE

ADJUSTMENT

LEVER

BASE

CLAMP

LEVER

FIG. 7

2610051825.qxp_1617 5/24/18 12:53 PM Page 11

Bosch routers are designed for speed,

accuracy and con venience in performing

cabinet work, routing, fluting, beading, cove-

cutting, dove tails, etc. They will enable you to

accomplish inlay work, decorative edges and

many types of special carving.

DEPTH ADJUSTMENT

WITH FIXED BASE

Router’s RA1161 fixed base are equipped with

a true micrometer type fine adjustment

mechanism, which can be used in any position

and provides precise adjustment of the router

bit position for unmatched accuracy. When the

tool is lowered to the approximate position

desired, this device may be adjusted to

precisely set the final bit position.

Your router also features three horizontal

notches on both sides of the motor housing for

coarse adjustments. The notches are spaced

1/2" apart which allows you to quickly lower or

raise the tool depth in three 1/2" increments.

(Approximately 12.7 mm), by simply

depressing the coarse adjustment release

lever.

TO ADJUST DEPTH

NOTE: All depth adjustments must be made

with the base clamp lever released.

1. Hold the tool in a horizontal position with the

base clamp lever facing you.

2. Open the base clamp lever to release the

motor.

Operating Instructions

FINE ADJUSTMENT DIAL

BASE CLAMP LEVER

COARSE

ADJUSTMENT

LEVER

INDICATOR RING

FIG. 10

CAST INDICATOR MARKS

CHIP DEFLECTOR

Always wear eye

protection. The chip

deflector is not intended as a safety guard.

The chip deflectors help keep dust and chips

out of your face, it will not stop objects larger

than dust thrown from the bit.

To remove chip shield from bases, press

inward on tabs until it releases from base and

remove. To attach, place deflector into position

as shown in (Fig. 9). Then flex sides of

deflector while pushing until it snaps into place.

The plunge base’s chip shield can also be

flipped out.

-12-

FIG. 9

!

WARNING

A

B

2610051825.qxp_1617 5/24/18 12:53 PM Page 12

-13-

3. COARSE ADJUSTMENT:

To make a large depth adjustment, depress

coarse adjustment release lever and raise or

lower to desired depth. There are three

notches in the motor housing which are

spaced 1/2" to facilitate this adjustment.

4. FINE DEPTH ADJUSTMENT:

To use the fine adjustment feature, turn the

fine adjustment knob clockwise to lower the

router bit or counter-clockwise to raise it.

NOTE: Be sure coarse adjustment lever is

engaged in one of the coarse adjustment

notches before making a fine adjustment.

To allow precise settings, the indicator ring is

graduated in English and Metric increments.

(Note: one full turn of fine adjustment knob =

1/16" or approximately 1.5 mm. The fine

adjustment mechanism has a total adjustment

range of 7/8" (23 mm). Each cast indicator

mark next to coarse adjustment lever is equal

to 1/8"

To prevent damage to tool, avoid wedging the

coarse adjustment lever against the upper A or

lower B portion of the housing as shown in

figure 10.

5. After making depth adjustments, re-clamp

the motor.

The indicator ring may be reset to zero without

moving the fine adjustment knob, to allow the

user to begin the adjustment from any

reference point desired.

When the router is installed in a router table,

it can be adjusted with a 1/8” hex wrench, not

included with all models. (See page 21).

The RA1002 Fine Adjustment Control

Extension, an optional accessory for the non-

plunge bases, allows fine adjustment from

beyond the top of the motor housing. To

install, simply press the RA1002 into the end

of the base’s own fine adjustment knob.

(Fig. 11)

TO CLAMP MOTOR

When final coarse and fine adjustments have

been made, fasten the base clamp lever to

secure adjustments. (If additional clamping

force is desired: using a 10 mm wrench,

rotate clamp nut clockwise SLIGHTLY (1/8

turn or less), then test clamp. Do not over-

tighten.)

DEEP CUTS

For deeper cuts, make several progressively

deeper cuts by starting at one depth and

then make several subsequent passes,

increasing the cutting depth with each pass.

To be certain that your depth settings are as

desired, you may want to make test cuts in

scrap material before beginning work.

FIG. 11

DEPTH ADJUSTMENT WITH PLUNGE

BASE PLUNGING ACTION

The plunge feature simplifies depth

adjustments and will allow the cutting bit to

easily and accurately enter the workpiece. To

lower, push plunge lock lever to the left, apply

downward pressure until you reach desired

depth, and release pressure on lever to lock

(Fig. 12). The plunge lock lever is spring

loaded and returns automatically to the locked

position. To raise the router, push plunge lock

lever to the left, release pressure on router and

the router will automatically retract the bit from

the workpiece. It is advisable to retract the bit

whenever it is not engaged in work piece.

FIG. 12

2610051825.qxp_1617 5/24/18 12:53 PM Page 13

DEEP CUTS

For deeper cuts, make several progressively

deeper cuts by starting with the highest step on

the depth turret, and after each cut, rotate the

depth turret to progressively lower steps as

desired, until the final depth (lowest step or flat)

is reached. Steps progress by 1/8” increments.

To be certain that your depth settings are as

desired, you may want to make test cuts in

scrap material before beginning work.

FINE ADJUSTMENT

The RA1166 plunge base is equipped with a

fine adjustment system that allows you to

micro adjust the plunge depth of the router bit

for superior routing accuracy.

Each complete revolution of the fine

adjustment stop adjusts the plunging depth by

1/32”, and each of the four indicator marks on

the knob represents 1/128”. One of the four

tick marks is larger than the other to indicate a

complete revolution. A reference indicator line

is built in to the depth rod.

To use the fine adjustment knob, once the

depth rod and turret have been set, check the

final depth setting and fine-adjust as follows:

To micro-increase the plunge depth, raise the

fine adjustment stop by turning it counter-

clockwise by the desired amount.

To micro-reduce the plunge depth, lower the

fine adjustment stop by turning it clockwise by

the desired amount.

2

1

0

IN

50

40

30

20

10

0

MM

FIG. 13

DEPTH INDICATOR

KNOB

DEPTH

INDICATOR

DEPTH ROD

DEPTH STOP

TURRET

DEPTH ROD FINE

ADJUSMENT KNOB

-14-

DEPTH ROD AND TURRET

The depth rod and the depth stop turret are

used to control cutting depth as follows;

1. With the bit installed, gently lower the motor

until the tip of the router bit just contacts the

level surface the router is sitting on. This is

the “zero” position, from which further depth

adjustments can be accurately made.

2. To set a desired depth of cut, rotate depth

stop turret until the lowest step is aligned

with the depth rod. Loosen depth indicator

knob and lower the depth rod until it

contacts the lowest step of the turret. Slide

the depth indicator until the red line indicates

zero on the depth scale, indicating the point

at which the bit just contacts the work

(Fig. 13).

3. To set a desired cutting depth, slide the

depth rod up until the red depth indicator line

attains the desired cutting depth, and secure

the rod in position by firmly tightening the

depth indicator knob.

4. The desired depth of cut may now be

achieved by plunging the router until the

depth rod contacts the selected stop on the

turret.

2610051825.qxp_1617 5/24/18 12:53 PM Page 14

-15-

Notes:

• When micro-adjusting the plunge depth, it is

more convenient to move the fine

adjustment stop up than down. Before

setting the depth rod and turret, make sure

the fine adjustment stop has been turned

several revolutions down from its top

position so that it can be adjusted upward.

• The fine adjustment stop cannot be use to

reduce the plunge depth when the depth rod

is already touching the depth stop turret.

The router must be raised before such an

adjustment can be made.

• Also available is an alternative turret that

has an adjustable step which uses an M4

screw for the adjustable step. The

adjustable step makes it possible to make

multiple-pass applications without having to

make a fine depth adjustment even when

the total cutting depth is not a multiple of

1/8".

ROCKER “ON/OFF” SWITCH

Your tool can be turned “ON” or “OFF” by the

rocker switch located on the motor housing.

One side of the switch is marked “I” for “ON“,

and the other side of switch is marked “O” for

“OFF“. Also the edge of switch displays red

when switch is in the “ON“ position.

TO TURN THE TOOL “ON”: Push the side of

the switch marked “I”.

TO TURN THE TOOL “OFF”: Push the side

of the switch marked “O”.

Always hold the router off the work when

turning the switch on or off. Contact the work

with the router after the router has reached full

speed, and remove it from the work before

turning the switch off. Operating in this manner

will prolong switch and motor life and will

greatly increase the quality of your work (Fig. 1).

ROCKER POWER "ON-OFF" WITH

TRIGGER SWITCH AND "LOCK-

ON"BUTTON

(Model 1618EVS only)

The power is switched "ON" by the rocker

switch located on the top of the motor housing

as described above. Now your tool can be

turned "ON" or "OFF" by squeezing or

releasing the trigger. Your tool is also equipped

with “Lock-ON” button located just above the

trigger that allows continuous operation without

holding the trigger (Fig. 2).

TO LOCK SWITCH ON: Squeeze trigger,

depress button and release trigger.

TO UNLOCK THE SWITCH: Squeeze trigger

and release it without depressing the “Lock-

ON” button.

If the “Lock-ON” button is

continuously being

depressed, the trigger cannot be released.

On model 1617 hold the tool with both hands

while starting the tool, since torque from the

motor can cause the tool to twist.

SOFT START FEATURE

(Models 1617EVS & 1618EVS only)

Electronic feedback control minimizes torque

twist customary in larger routers by limiting the

speed at which motor starts.

ELECTRONIC VARIABLE

SPEED CONTROL

(Models 1617EVS & 1618EVS only)

The electronic speed control feature allows

motor speed to be matched to cutter size and

material hardness for improved finish,

extended bit life, and higher performance.

Speed changes are achieved by rotating

Control Dial RIGHT to increase speed, LEFT

to decrease as indicated on housing (Fig. 1).

Speed may be changed while tool is on. The

reference numbers on the dial facilitate re-

setting control to desired speed.

The speed chart indicates the relationship

between settings and application, exact settings

are determined by operator experience and

preference. The bit manufacturer may also

have a speed recommendation.

CONSTANT RESPONSE™ CIRCUITRY

(Models 1617EVS & 1618EVS only)

The router's Constant Response™ Circuitry

monitors and adjusts power to maintain the

desired RPM for consistent performance and

control.

!

WARNING

DIAL

SETTING RPM APPLICATION

1 8,000

2 13,500

3 16,500

4 20,000

5 21,500

6 25,000

}

Nonferrous metals,

larger diameter bits

and cutters

Softwoods, plastics,

counter tops, smaller

diameter bits and

cutters

2610051825.qxp_1617 5/24/18 12:53 PM Page 15

FEEDING THE ROUTER

As seen from the top of the router, the bit turns

clockwise and the cutting edges face

accordingly. Therefore, the most efficient cut is

made by feeding the router so that the bit turns

into the work, not away. Figure 14 shows

proper feed for various cuts. How fast you feed

depends on the hardness of the material and

the size of the cut. For some materials, it is

best to make several cuts of increasing depth.

If the router is hard to control, heats up, runs

very slowly or leaves an imperfect cut,

consider these causes:

1. Wrong direction of feed — hard to control.

2. Feeding too fast — overloads motor.

3. Dull bit — overloads motor.

4. Cut is too large for one pass — overloads

motor.

5. Feeding too slow — leaves friction burns on

work.

Feed smoothly and steadily (do not force). You

will soon learn how the router sounds and feels

when it is working best.

RATE OF FEED

When routing or doing related work in wood

and plastics, the best finishes will result if the

depth of cut and feed rate are regulated to

keep the motor operating at high speed. Feed

the router at a moderate rate. Soft materials

require a faster feed rate than hard materials.

The router may stall if improperly used or

overloaded. Reduce the feed rate to prevent

possible damage to the tool. Always be sure

the collet chuck is tightened securely before

use. Always use router bits with the shortest

cutting length necessary to produce the

desired cut. This will minimize router bit run-out

and chatter.

GUIDING THE ROUTER

The router can be guided through the work in

any of several ways. The method you use

depends, of course, on the demands of the

particular job and on convenience.

For routing operations such as grooving or

dadoing, it is often necessary to guide the tool

in a line parallel to a straight edge. One

method of obtaining a straight cut is to securely

clamp a board or other straightedge to the

work surface, and guide the edge of the router

sub-base along this path (Fig. 15).

FIG. 14

FIG. 15

BIT

WORK

DIRECTION OF

ROUTER FEED

START

HERE

BOARD GUIDE

SECURELY CLAMP

BOARD GUIDE

FEED

DIRECTION

-16-

2610051825.qxp_1617 5/24/18 12:53 PM Page 16

ROUTER DUST COLLECTION

There are three optional dust extraction hood

accessories. Each dust extraction hood is

sized to accept 35mm vacuum hoses. Each

accessory pack includes the VAC002 adapter

that will connect the hood to 1-1/4” and 1-1/2”

vacuum hoses. An adapter to connect the

hood to 2-1/2" hoses is also available

separately.

ROUTER DUST COLLECTION FOR

PLUNGE BASE

This dust extraction hood is designed for use

the plunge base (RA1166) when routing is

done in the middle of the workpiece, such as

when creating slots or routing patterns for

inlays. If you have a shop vacuum system, you

can attach the dust extraction hood for

improved visibility, accuracy and utility,

particularly in freehand routing.

To attach, position as shown and secure

adapter to base with the thumbscrews

provided (Fig. 16).

The dust extraction hood can also be installed

with the hose outlet facing the front of the tool.

If the templet guide adapter is installed, it will

need to be reversed or removed to allow the

release lever to fit under the dust hood.

FIG. 16

DUST EXTRACTION HOOD

(Optional Accessory)

M4 THUMB

SCREWS

-17-

DUST EXTRACTION HOOD FOR

BACKSIDE OF FIXED BASE

Read and understand these

instructions and tool

manual for use of these accessories.

Do not reach in area of the bit while the

router is ON or plugged in.

To avoid entangling hoses,

do not use this dust

extraction hood at the same time as any

other dust extraction hood.

This dust extraction hood is designed for use

with Bosch routers 1617, 1617EVS, 1618EVS

and their fixed bases when the routing is done

in the middle of the workpiece, such as when

creating slots or routing out patterns for inlays.

To attach the hood to the router base, slide

the hood into the backside of the router base

around the router’s depth adjustment rod with

the hood’s rounded corners facing up (Fig. 17

& 18). Securely tighten the two knurled

thumbscrews.

USING THE HOOD FOR BACKSIDE OF

FIXED BASE

For maximum dust collection effectiveness,

make sure the router’s chip shield is in place.

!

WARNING

!

CAUTION

DUST

EXTRACTION

HOOD

ROUTER

BASE

M5 SCREW

FIG. 17

FIG. 18

2610051825.qxp_1617 5/24/18 12:53 PM Page 17

-18-

EDGEFORMING DUST

EXTRACTION HOOD

Do not reach in area of the

bit while the router is ON or

plugged in. To avoid entangling hoses, do

not use this dust extraction hood at the

same time as any other dust extraction

hood.

This dust extraction hood (optional accessory)

is used for dust collection when edge-forming

(Fig. 19).

ATTACHING DUST EXTRACTION HOOD

You can attach the edge-forming hood in

several places according to your needs or

preferences. This hood is attached using two

of the screw holes on the router base that are

used to attach the router’s sub-base. Choose

the desired location for the hood. Loosen and

take out the two screws from the router base

and attach the dust extraction hood — over the

router’s sub-base — using the screws provided

with the hood. Securely tighten the screws.

(Figures 20 & 21).

DUST

EXTRACTION

HOOD

ROUTER

SUB-BASE

WORKPIECE

EDGE

!

WARNING

M4 x 16mm

SCREW

M4 x 16mm

SCREW

M4 x 16mm

SCREW

SUB-BASE

DUST

EXTRACTION

HOOD

M4 x 16mm

SCREW

FIG. 19

DUST

EXTRACTION

HOOD

FIG. 20

PLUNGE BASE

FIG. 21

OTHER BASES

2610051825.qxp_1617 5/24/18 12:53 PM Page 18

-19-

DELUXE ROUTER GUIDE

(Not included, available as accessory)

The Bosch deluxe router guide is an optional

accessory that will guide the router parallel to a

straight edge or allow you to create circles and

arcs.

The deluxe router guide is supplied with two

rods and screws to fasten the guide (Fig. 22).

In addition, it features a fine adjustment knob

and indicator for accurately positioning the

edge guide relative to the bit. With the guide

installed and adjusted, the router should be fed

normally, keeping the guide in contact with the

edge of the workpiece at all times. The deluxe

router guide may also be positioned directly

under the router base for operations where a

cut is needed close to or at the edge of the work.

The deluxe router guide includes a dust

extraction hood and the VAC002 vacuum hose

adapter.

For complete instructions on installation and

operation, please refer to the instructions

which are included with this accessory.

FIG. 22

DESIRED

WIDTH

CUT

BASE

WORKPIECE

ROUTER

GUIDE

RODS

M6 WING

SCREW

M6 WING SCREW

FINE

ADJUSTMENT

KNOB

FINE

ADJUSTMENT

INDICATOR

FEED

DIRECTION

TEMPLET GUIDES

This router can also be used with the optional

Bosch-exclusive quick-change templet guide

system, which firmly grips the guides with a

spring-loaded ring. Unlike conventional

threaded templet guides, there is no threaded

ring that can come loose while routing.

Templet guides are used with a number of

special accessories, such as hinge templets,

which are listed in your BOSCH catalog. In

addition, special templets are easily prepared

for cutting repeated patterns, special

designs, inlays, and other applications. A

templet pattern may be made of plywood,

hardboard, metal or even plastic, and the

design can be cut with a router, jigsaw, or

other suitable cutting tool. Remember that

the pattern will have to be made to

compensate for the distance between the

router bit and the templet guide (the “offset”),

as the final workpiece will differ in size from

the templet pattern by that amount, due to

the bit position (Fig. 24).

TEMPLET GUIDE

(optional accessory)

TEMPLET GUIDE

ADAPTER

TEMPLET GUIDE

RELEASE LEVER

COLLET CHUCK

WORKPIECE

ROUTER BIT

OFFSET

TEMPLET

GUIDE

TEMPLET

PATTERN

FIG. 24

ROUTER

SUB-BASE

FIG. 23

2610051825.qxp_1617 5/24/18 12:53 PM Page 19

-20-

INSTALLING TEMPLET GUIDE ADAPTER

(Not included, available as accessory)

Place templet guide adapter over the holes in

the center of the sub-base, and align the two

threaded holes in the bottom of adapter with

the countersunk holes in sub-base. Fasten

adapter with the screws provided. Note that

the adapter is reversible, so the release lever

may be positioned as desired. (Fig. 25)

TEMPLET GUIDE

ADAPTER

(optional accessory)

MOUNTING SCREWS

CENTERING THE SUB-BASE OR

TEMPLET GUIDES

Your router features the Bosch “Precision

Centering Design”. Its sub-base is precisely

centered at the factory. This positions the bit at

the center of the sub-base and optional

templet guides.

Precision centering allows you to use the edge

of the subbase or templet guides to closely

follow jigs such as straight guides, templets,

and dovetail fixtures without worrying about bit

walk-off from the intended cut line for any

reason, including the orientation of the router’s

handles relative to the jig.

To quickly re-center the sub-base, attach the

sub-base using the set of flathead screws

(included) and the countersunk screw holes in

the sub-base. (Flathead screws have the

tapered heads.) The flathead screws and

countersunk holes will pull the sub-base into a

position that is very close to centered.

To most precisely re-center the sub-base or

templet guides, attach the sub-base using the

optional Bosch RA1151 Centering Device.

Follow steps 1-8 (Fig. 26 & 27).

1. If a templet guide is to be centered, Install

the templet guide adapter and template

guide (optional attachments) as described

elsewhere in this manual.

2. Position the sub-base so that its pan-head

screw holes are over the matching set of

threaded holes in the base.

3. Insert the pan-head screws through the sub-

base and tighten them until they are snug,

but still allow the sub-base to move.

CENTERING SHAFT

(optional accessory)

FIG. 26

PLUNGE BASE

FIG. 27

OTHER BASES

A = M4 COUNTERSUNK SCREW

HOLES

B = M4 PAN-HEAD SCREW HOLES

C = TEMPLET GUIDE ADAPTER

SCREW HOLES

D = HOLES FOR ATTACHING

ROUTER TO ROUTER TABLE

MOUNTING PLATE

(Under sub-base on

non-plunge bases)

D D

BAB

A

BA

C

D

CENTERING SHAFT

(optional accessory)

TEMPLET GUIDE

(optional accessory)

SUB-BASE

FIG. 25

CENTERING CONE

(optional accessory) CENTERING SHAFT

(optional accessory)

2610051825.qxp_1617 5/24/18 12:53 PM Page 20

La page charge ...

Bosch 1617EVSPK Wood 12 Amp Router Tool Combo Kit Manuel utilisateur

Bosch 1617EVSPK Wood 12 Amp Router Tool Combo Kit Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents