Sony RMO-S561 Le manuel du propriétaire

4-650-926-18(1)

User’s Guide

Mode d’emploi

Bedienungsanleitung

Guía del usuario

Istruzioni per l’uso

RMO-S561

MO Disk Unit

2

Owner’s Record

The model and serial numbers are located on the

bottom of the unit. Record the serial number in

the space provided below.

Refer to them whenever you call upon your Sony

dealer regarding this product.

Model No. RMO-S561

Serial No._________________________

Information

For the customer in the U.S.A.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment

and receiver.

–Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

–Consult the dealer or an experienced radio/TV

technician for help.

This device requires shielded interface cables to

comply with FCC emission limits.

Safety Regulations

If you have any questions about this product, you

may call: Sony Customer Information Center 1-

800-352-SONY(7669) or write to: Sony

Customer Information Center 3300 Zanker Road,

San Jose, CA 95134.

Declaration of Conformity

Trade Name: SONY

Model No.: RMO-S561

Responsible Party: Sony Electronics Inc.

Address: 16530 Via Esprillo,

San Diego,

CA 92127 U.S.A.

Telephone No.: 858-942-2230

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) This device must

accept any interference received, including

interference that may cause undesired operation.

3

WARNING

To reduce the risk of fire or electric

shock, do not expose this apparatus to

rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified

personnel only.

CAUTION

As the laser beam used in the RMO-S561 is

harmful to the eyes, do not attempt to

disassemble the unit.

Refer servicing to qualified personnel only.

The use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous

radiation exposure.

This label is affixed inside the unit.

CLASS 3B LASER RADIATION WHEN OPEN.

AVOID DIRECT EXPOSURE TO THE BEAM.

RADIATIONS LASER DE CLASSE 3B EN CAS D'OUVERTURE.

EVITER TOUTE EXPOSITION DIRECTE AU FAISCEAU.

KLASSE 3B LASERSTRAHLUNG WENN GEÖFFNET.

DIREKTEN KONTAKT MIT DEM STRAHL VERMEIDEN.

LASERSTRÅLING AF KLASSE 3B VED ÅBNING.

UNDGÅ DIREKTE UDSÆTTELSE FOR STRÅLING.

LASERSTRÅLING I KLASSE 3B NÅR DEKSEL ÅPNES.

UNNGÅ DIREKTE EKSPONERING FOR STRÅLEN.

KLASS 3B LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD.

UNDVIK ATT DIREKT EXPONERA DIG FÖR STRÅLNINGEN.

AVATTUNA LUOKAN 3B LASERSÄTEILYÄ.

VÄLTÄ SUORAA ALTISTUMISTA SÄTEELLE.

CAUTION

ATTENTION

VORSICHT

ADVARSEL

VARNING

VARO!

This MO disk unit is classified as a CLASS 1

LASER PRODUCT.

The CLASS 1 LASER PRODUCT

label is located on the bottom exterior.

CLASS 1

LASER PRODUCT

LASER KLASSE 1

PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

English

NOTICE

Use the power cord set approved by the

appropriate testing organization for the

specific countries where this unit is to be used.

CAUTION

The mains plug on this equipment must be

used to disconnect mains power.

Please ensure that the socket outlet is installed

near the equipment and shall be easily

accessible.

Disposal of Old Electrical & Electronic

Equipment (Applicable in the European

Union and other European countries with

separate collection systems)

This symbol on the product or on its

packaging indicates that this product

shall not be treated as household

waste. Instead it shall be handed over

to the applicable collection point for

the recycling of electrical and

electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent

potential negative consequences for the

environment and human health, which could

otherwise be caused by inappropriate waste

handling of this product. The recycling of

materials will help to conserve natural resources.

For more detailed information about recycling of

this product, please contact your local Civic

Office, your household waste disposal service or

the shop where you purchased the product.

According to the EU Directives related to

product safety, EMC and R&TTE the

manufacturer of this product is Sony

Corporation, 6-7-35 Kitashinagawa

Shinagawa-ku Tokyo, 141-0001 Japan.

The Authorised Representative is Sony

Deutschland GmbH, Hedelfinger Strasse

61,70327 Stuttgart, Germany.

For any service or guarantee matters please

refer to the addresses given in separate service

or guarantee documents.

4

Table of Contents

Using this Guide........................................ 5

Chapter 1 Introduction

Overview .................................................... 6

Features ....................................................... 6

Compatible Disks ....................................... 7

System Configuration ................................. 8

Location and Function of Parts ............... 9

Chapter 2 Getting Started

Component and Accessory Check List 10

Connecting the Disk Unit ....................... 11

Setting the SCSI ID.................................. 11

Setting the Disk Unit’s Functions .......... 12

Chapter 3 Using the Disk Unit

Inserting a Disk Cartridge ...................... 13

Ejecting a Disk Cartridge........................ 14

Chapter 4 Precautions

On the Disk Unit ...................................... 15

Safety Considerations ............................... 15

Damage Prevention .................................. 15

On the Disk Cartridges ........................... 16

Other Points Requiring Attention ............. 16

Protecting Your Data ................................ 17

Cleaning ................................................... 17

Cleaning a Disk ........................................ 17

Appendix

Specifications .......................................... 18

Disk Unit .................................................. 18

Optional Accessories ................................ 19

5

Using this Guide

This guide covers the use and operation of the

RMO-S561 Magneto-Optical Disk Unit (called

the “disk unit” thereafter). Do not attempt to use

the disk unit without first carefully reading this

guide. When finished, keep it handy for future

reference.

The guide is divided into the following sections.

Chapter 1 Introduction

This chapter contains a general overview of the

RMO-S561 disk unit, touching upon its features,

system configuration, and the location and

function of its parts.

Chapter 2 Getting Started

This chapter explains how to connect the disk

unit to the host computer and other SCSI

peripheral devices. It also explains how to set the

disk unit’s functions and the SCSI ID. Refer to

this chapter when setting up the disk unit.

Chapter 3 Using the Disk Unit

In this chapter, you learn how to turn on the disk

unit, and how to insert and eject a disk cartridge.

Refer to this chapter when you are ready to

actually begin using the disk unit.

Chapter 4 Precautions

This chapter contains precautions regarding the

use and operation of the disk unit and magneto-

optical disk cartridges.

It also discusses cleaning of disks.

Be sure to refer to this chapter before using the

disk unit.

Appendix

The Appendix contains an explanation of the disk

unit’s main specifications.

Notes

• The manufacturer disclaims all responsibility

for any losses incurred through malfunction or

use of this product.

• The manufacturer does not warrant the security

of data stored using this product. To guard

accidental data loss, frequent backup of

important data is highly recommended.

• Reproduction of the contents of this manual, in

whole or in part, is prohibited.

•Macintosh is a registered trademark of Apple

Computer, Inc.

•Microsoft and Windows are registered

trademarks of Microsoft Corporation.

6 Chapter 1 Introduction

Chapter 1 Introduction

Overview

Features

The RMO-S561 Magneto-Optical Disk Unit has

the following features:

•Magneto-optical technology enables repeated

writing and erasing of data on the disk.

• The disk unit automatically senses the type of

disk being inserted, enabling the free use of

both 650 Mbytes (594 Mbytes), 1.3 Gbytes (1.2

Gbytes), 2.6 Gbytes (2.3 Gbytes), 5.2 Gbytes

(4.8 Gbytes, 4.1 Gbytes), and 9.1 Gbytes (8.6

Gbytes) disks indifferently.

•A maximum of 9.1 Gbytes (4,096 bytes/sector),

8.6 Gbytes (2,048 bytes/sector), 9.1 Gbytes

(1,024 bytes/sector), or 9.1 Gbytes (512 bytes/

sector) of data can be written on the two sides

of a 5.25-inch magneto-optical disk. This is

equivalent to about 6100–6500 times the

capacity of a conventional 3.5-inch floppy disk

(2HD).

• Any disk conforming to the internationally

accepted CCS (continuous/composite servo) or

CCW (continuous composite write-once) format

can be used in this disk unit.

• This disk unit employs SCSI-2 (Small

Computer System Interface-2).

• The 3,000 min

-1

(rpm) high-speed

spindle motor enables data transfer rates of

3.07 – 6.14 Mbytes/s (4,096 bytes/sector),

2.87 – 5.84 Mbytes/s (2,048 bytes/sector),

3.07 – 6.14 Mbytes/s (1,024 bytes/sector), or

3.07 – 6.14 Mbytes/s (512 bytes/sector).

•With disk capacities under 5.2 Gbytes (4.8

Gbytes, 4.1 Gbytes), the spindle motor rotates at

3300 min

-1

(rpm).

•With disk capacities under 2.6 Gbytes (2.3

Gbytes), the spindle motor rotates at 3600 min

-1

(rpm).

• The low-profile, light-weight optical pick-up

yields average seek times of 25ms.

• Use of a highly reliable error correction code

(ECC) system keeps the error rate as low as

10

-12

.

• Optimum operation environment is provided

through use of a large, 8MB buffer and

optimized cache control algorithm. (Write cache

can be enabled or disabled. For details, see

“Setting the Disk Unit’s Functions” on page

12.)

Chapter 1 Introduction 7

Compatible Disks

The RMO-S561 can use the following Sony 5.25-inch MO Disks:

Standard Sector format Type* Capacity Sony equivalent

ISO/IEC 15286 2048 bytes/sector R/W About 5.2 G bytes EDM-5200B

ISO/IEC 15286 1024 bytes/sector R/W About 4.8 G bytes EDM-4800B

ISO/IEC 15286 512 bytes/sector R/W About 4.1 G bytes EDM-4100B

ISO/IEC 14517 1024 bytes/sector R/W About 2.6 G bytes EDM-2600B

ISO/IEC 14517 512 bytes/sector R/W About 2.3 G bytes EDM-2300B

ISO/IEC 13549 1024 bytes/sector R About 1.3 G bytes EDM-1300B

ISO/IEC 13549 512 bytes/sector R About 1.2 G bytes EDM-1200B

ISO/IEC 10089 1024 bytes/sector R About 650 M bytes EDM-650B

ISO/IEC 10089 512 bytes/sector R About 600 M bytes EDM-600B

ISO/IEC 15286 2048 bytes/sector WO About 5.2 G bytes CWO-5200B

ISO/IEC 15286 1024 bytes/sector WO About 4.8 G bytes CWO-4800B

ISO/IEC 15286 512 bytes/sector WO About 4.1 G bytes CWO-4100B

ISO/IEC 14517 1024 bytes/sector WO About 2.6 G bytes CWO-2600B

ISO/IEC 14517 512 bytes/sector WO About 2.3 G bytes CWO-2300B

ISO/IEC 13549 1024 bytes/sector R About 1.3 G bytes CWO-1300B

ISO/IEC 13549 512 bytes/sector R About 1.2 G bytes CWO-1200B

ISO/IEC 11560 1024 bytes/sector R About 650 M bytes CWO-650B

ISO/IEC 11560 512 bytes/sector R About 600 M bytes CWO-600B

ISO/IEC 22092 4096 bytes/sector R/W About 9.1 G bytes EDM-9100B

ISO/IEC 22092 2048 bytes/sector R/W About 8.6 G bytes EDM-8600B

ISO/IEC 22092 1024 bytes/sector R/W About 9.1 G bytes EM1-9100B

ISO/IEC 22092 512 bytes/sector R/W About 9.1 G bytes EM5-9100B

ISO/IEC 22092 4096 bytes/sector WO About 9.1 G bytes CWO-9100B

ISO/IEC 22092 2048 bytes/sector WO About 8.6 G bytes CWO-8600B

*R/W:Rewritable, R/W:Rewritable(MO), WO:Write Once, R:Read Only

8 Chapter 1 Introduction

System Configuration

The disk unit should be used with a host

computer equipped with SCSI.

A maximum of seven peripheral devices can be

linked in a daisy chain on the SCSI bus, and

controlled with SCSI-2 commands.

Host computer

SCSI cable

RMO-S561 disk unit SCSI peripheral devices

Chapter 1 Introduction 9

Location and Function of Parts

Front Panel

EJECT

POWER

BUSY

1

23

456

1 POWER switch

Push the button to turn the power on and off.

The power is on when the button is in the

depressed position, and off when fully

protruding.

2 POWER indicator

The green lamp lights up when the power is

turned on.

3 BUSY indicator

As this disk is inserted and the drive becomes

ready for read/write operation, the BUSY

indicator turns green. The orange lamp lights

up when the disk unit is accessing or writing

data. This lamp flashes on and off at about 2-

second intervals when the unit overheats,

regardless of whether or not a disk is being

accessed.

4 Disk insertion slot

Insert the disk cartridge into this slot. Refer

to the section “Inserting a Disk Cartridge” on

page 13 for more information.

5 Emergency eject hole

If the disk cartridge cannot be ejected using

the EJECT button 6, turn off the power and

insert the supplied emergency eject tool into

this hole to trip the emergency eject

mechanism. Refer to the section “What to do

if the disk does not eject” on page 14 for

further details.

6 EJECT button

Press this button to eject the disk cartridge

from the disk unit. The EJECT button is

disabled with the function switch or software

settings prohibit ejection. When the write

cache is enabled, it may take a few moments

(up to 45 seconds) for the disk to eject

because data in the cache must first be

written to the disk.

Rear Panel

A

1

BCDEFGH

0

SCSI CONNECTOR

AC IN

F.GND

SCSI ID

123 4 56

1 Function switches

Use this switches to set the disk unit’s

functions in accordance with the host

computer and software being used. Refer to

the section“Setting the Disk Unit’s

Functions” on page 12 for more information.

2 SCSI ID switch

Use these switches to set the SCSI ID. Push

the “–” button to lower the ID number; push

the “+” button to raise the ID number. Refer

to the section“Setting the SCSI ID”on page

11 for more information.

3 SCSI connectors

Plug SCSI cables (sold separately) linking

the host computer and other SCSI peripherals

into these connectors.

Note

If the disk unit is the last device on the SCSI

chain, set function switch F to “1” to turn on

the internal terminator. When it is not the last

device, make sure that the terminator is off

(switch F is set to “0”).

4 Air duct

The air for cooling the disk unit flows

through this duct, so be careful not to block

its surface or impede the outflow.

5 F.GND (frame ground) terminal

Connect the ground terminals of other

devices to the disk unit’s frame ground.

6 AC IN (AC power) connector

Connect the supplied AC power cord to this

connector.

10 Chapter 2 Getting Started

Chapter 2 Getting Started

Before setting up your RMO-S561 Magneto-

Optical Disk Unit, check to see that you have all

the required components and accessories. Then,

connect the disk unit to the host computer and

any other SCSI peripherals you may be using.

After checking to see that all the connections

have been properly made, set the SCSI ID using

the SCSI ID switch and the disk unit’s functions

using the function switches.

Note

Please refer to the installation manual included in

the device driver’s package for instructions when

using this device with a Macintosh

®

computer or

a computer running under Windows

®

system. For

questions concerning the device drivers, please

contact the device driver manufacturer as

indicated in the device driver package.

Component and Accessory Check List

Upon opening the carton, check to see that you

have all of the components and accessories listed

below. Contact your dealer immediately if you

find any missing or damaged items.

•RMO-S561 Magneto-Optical Disk Unit

• AC power cord

• Emergency eject tool

• User’s Guide

• Guide to Safe Use (Safety Precautions)

•1 Blank MO disk

RMO-S561 Emergency eject tool AC Power cord

Magneto-Optical Disk Unit

Chapter 2 Getting Started 11

You can hook up a maximum of seven SCSI

peripheral devices to a single host computer

through its SCSI bus.

Use the following Sony SCSI cable (sold

separately) to connect the disk unit.

Notes

• Before connecting the disk unit, be sure to turn

off the disk unit and all other devices on the

SCSI chain.

• If the disk unit is the last device on the SCSI

chain, set the function switch F on the rear

panel to “1” to turn on the internal terminator.

When it is not the last device, make sure that the

terminator is off (function switch F is set to

“0”).

• The total length of the SCSI cables connected to

a SCSI chain must not exceed six meters (19

feet 8

1

/4 inches).

Connecting the Disk Unit

A

1

BCDEF GH

0

SCSI CONNECTOR

AC IN

F.GND

SCSI ID

Setting the SCSI ID

to SCSI connector

to AC IN

connector

AC power cord

(supplied)

SCSI-2 cableSCSI-2 cable

to another

SCSI device

to the host computer or

another SCSI device

to an AC outlet

RMO-S561 Magneto-Optical Disk Unit

The factory default setting for the SCSI ID is “0.”

If necessary, this ID number can be changed

using the SCSI ID switch on the rear panel. Be

sure to turn off the power before making any

changes.

Pushing the “+” button raises the ID number;

pushing the “–” button lowers the ID number.

Notes

• The disk unit will not operate properly unless

the SCSI ID has been set correctly.

•Make sure to select a SCSI ID that has not been

assigned to another SCSI device.

0

12 Chapter 2 Getting Started

Setting the Disk Unit’s Functions

Use function switches (A – H) on the rear panel

to select the disk unit’s functions in accordance

with the host computer and software you are

using. Be sure to turn off the power before setting

the switches.

A

1

BCDEFGH

0

■ Write Cache Precautions

This disk unit is equipped with a write cache

function. When the write cache is enabled, never

turn off the disk unit power without making sure

that all data has been written to the disk from the

cache memory.

Data will be lost if you turn off the power before

all data in cache memory has been written to the

disk. Before turning off the disk unit power, be

sure to eject the disk, as this writes data from

cache memory to the disk.

Further, even though the drive will periodically

flush data from cache memory periodically to the

disk, data may be lost in the case of a power

failure.

■ Ultra SCSI Precautions

Using the Ultra SCSI function requires that an

Ultra SCSI cable be used to connect the disk unit

and the host system. It is recommended that the

cumulative cable length be minimized, and that

the cable length be kept under 3 m in length

when connecting up to four SCSI peripheral

devices. In all other cases, the total length of the

cable should not exceed 1.5 m. Further, the SCSI

bus termination should be well maintained.

■ Precautions for Handling the 1024

and 512 bytes/sector

Note that this drive uses a sector size of 4096

bytes/sector. If you insert a disk with a sector size

of 1024 or 512 bytes/sector, the drive internally

converts the sector size of software to emulate a

sector size of 4096 bytes/sector.

Further, data already written to the disk may be

lost if the power is accidentally turned off while

data is being written to the disk.

Be careful when operating the power switch.

Function Switch Settings

Switch Function

10

A Parity check SCSI parity check is disabled. SCSI parity check is

enabled.

B Device type Peripheral device type 00H Peripheral device type 07H

(Direct Access Device) (Optical Memory Device)

C Write cache control Disable write cache. Enable write cache.

D Ultra SCSI control Ultra SCSI compatible Not Ultra SCSI compatible

E Force verify All write operations are verfied. All write operations are

(with a verify pass) normal operations.

(without a verify pass)

F Terminator The internal terminator is on. The internal terminator is off.

G Auto spin up Inserting a disk does not causes Inserting a disk causes

the spindle motor to rotate. the spindle motor to rotate.

H Manual eject Disk catridge cannot be ejected Disk cartridge can be

by pressing the EJECT button. ejected by pressing the

EJECT button

: Factory setting

Chapter 3 Using the Disk Unit 13

Use the following Sony 5.25-inch MO disks in

your RMO-S561 disk unit.

• EDM-9100B (4,096 bytes/sector, 9.1 Gbytes)

• EDM-8600B (2,048 bytes/sector, 8.6 Gbytes)

•EM1-9100B (1,024 bytes/sector, 9.1 Gbytes)

•EM5-9100B (512 bytes/sector, 9.1 Gbytes)

• EDM-5200B (2,048 bytes/sector, 5.2 Gbytes)

• EDM-4800B (1,024 bytes/sector, 4.8 Gbytes)

• EDM-4100B (512 bytes/sector, 4.1 Gbytes)

• EDM-2600B (1,024 bytes/sector, 2.6 Gbytes)

• EDM-2300B (512 bytes/sector, 2.3 Gbytes)

•CWO-9100B (4,096 bytes/sector, 9.1 Gbytes )

•CWO-8600B (2,048 bytes/sector, 8.6 Gbytes)

•CWO-5200B (2,048 bytes/sector, 5.2 Gbytes )

•CWO-4800B (1,024 bytes/sector, 4.8 Gbytes)

•CWO-4100B (512 bytes/sector, 4.1 Gbytes)

•CWO-2600B (1,024 bytes/sector, 2.6 Gbytes )

•CWO-2300B (512 bytes/sector, 2.3 Gbytes)

1 Press the POWER switch located on the left

side of the front panel.

This turns on the disk unit and causes the

POWER indicator to light up.

Chapter 3 Using the Disk Unit

Inserting a Disk Cartridge

2 Start up the host computer. Refer to the

manual supplied with the host computer for

the start up procedure.

3 Insert a disk cartridge with the side you want

to use facing upwards.

4 Access or write data on the disk using

software commands on the host computer.

The BUSY indicator lights up while the unit

is accessing the disk.

■ What to do if the disk unit stops

operating

When the temperature in the disk unit exceeds

the preset level, the BUSY indicator starts

flashing on and off at about 2-seconds intervals,

regardless of whether or not a disk is being

accessed, and the disk unit stops operating.

If this happens, you should improve the

ventilation of a setting area.

If the disk unit still refuses to operate, unplug the

unit and contact your dealer.

To use Side A, insert the

disk with “A” facing

upward.

Press the POWER switch

14 Chapter 3 Using the Disk Unit

Ejecting a Disk Cartridge

Eject the disk cartridge either by using software

commands or by pressing the EJECT button.

Note

Do not attempt to eject a disk cartridge while the

BUSY indicator is lit orange (except when it is

flashing at about 2-second intervals due to

overheating). Ejecting the disk while it is being

accessed may cause data write errors or may

result in loss of data.

Also, it may take a few moments (up to 45

seconds) for the disk to eject when the write

cache is enabled, because data in the cache must

first be written to the disk.

■ What to do if the disk does not

eject

The disk cartridge may not come out, even when

you press the EJECT button or use a software

command, under the following conditions:

• The eject function has been disabled using the

function switch or a software command;

• The host computer is not functioning properly;

• The disk unit has been turned off (due to a

power failure, etc.); or

• Something is wrong with your disk unit itself.

When you cannot eject the disk cartridge using

the EJECT button or software commands,

remove it as follows.

1 Turn off the disk unit if the power is still on.

2 Insert the emergency eject tool (or a paper

clip) straight into the emergency eject hole to

trip the manual ejection mechanism.

This should cause the disk cartridge to eject.

Caution

The tip of the emergency eject tool is sharp.

When handling the tool, please be careful to

avoid injury.

EJECT button

Emergency

eject Tool

Insert into the

emergency eject hole.

Chapter 4 Precautions 15

Chapter 4 Precautions

On the Disk Unit

Safety Considerations

■ Power supply

• Be sure to use 100 - 240V AC.

• Do not share the AC outlet with any other

power-consuming equipment such as copying

machines or shredders.

■ AC power cord

• Be careful not to place or drop heavy object on

the power cord, or subject it to anything that

may damage it.

•When unplugging the cord from an AC outlet,

be sure to grasp the plug itself. Pulling on the

cord may cause damage to the internal wiring.

• Unplug the unit when not using it for long

period of time.

■ Handling the emergency eject tool

The tip of the emergency eject tool is sharp.

When handling the tool, please be careful to

avoid injury. Do not use the tool for any purpose

other than ejecting disks.

Damage Prevention

■ Do not subject the disk unit to

shock or vibration

Dropping the unit or subjecting it to strong

impact may damage the disk unit.

■ Setting position

The disk unit is designed to be used in the

horizontal position. Do not position it at an angle.

■ Location requirements

Careful consideration should be given to the

following in selecting a site to install or store

your disk unit.

Avoid the following conditions:

• High humidity

• High temperatures

• Direct sunlight

• Dust

• Strong vibration

•Wide temperature fluctuations

■ Ventilation

Care should be exercised to prevent the internal

mechanisms of the disk unit from overheating.

Be careful not to clog or block the vent, or place

the unit in an area with poor ventilation. The disk

unit may stop operating altogether if the internal

temperature becomes too high.

■ Condensation

Avoid subjecting the disk unit to extremes in

temperature. If, for example, the disk unit is

moved suddenly from a very cold location to a

warm one, moisture from condensation may form

within the unit due to the quick rise in ambient

temperature. If a sudden change in the

temperature cannot be avoided, wait for an hour

or more before using the disk unit. Inserting a

disk cartridge into the mechanism when moisture

is present may cause damage to both the disk and

the disk unit. Remove the disk cartridge

immediately if you suspect any condensation

problems. The moisture should evaporate quickly

if the disk unit is left on without a disk inserted.

16 Chapter 4 Precautions

■ Moving the disk unit

Be sure to remove the disk cartridge when the

disk unit is not being used. Also never move or

transport the unit with the disk cartridge still

inserted.

While in operation, the disk rotates at a high

speed. Moving the disk unit at such a time may

disturb the spinning disk and cause it to be

damaged. Always remove the disk cartridge

before moving your disk unit.

■ If problems occur

If any problems occur, turn off the power and

unplug the disk unit, contact your dealer.

Other Points Requiring Attention

■ Electrical noise

The high-frequency signal generated by the disk

unit may cause interference or static on other

electrical appliances such as radios, televisions

and audio tuners. If this should occur, move the

disk unit a little farther away from the affected

appliance.

■ Maintenance

Clean the cabinet with a dry soft cloth, or with a

soft cloth lightly moistened with a mild detergent

solution. Do not use any type of solvent, such as

alcohol or benzine, which may damage the finish.

On the Disk Cartridges

• Do not drop the disk cartridge or subject it to

any violent shocks or vibration.

• Do not disassemble the disk cartridge. It is a

precision component and has been carefully

adjusted at the factory prior to shipment.

• Do not open the disk cartridge’s shutter

manually or touch the disk inside. The shutter is

designed to open automatically when the

cartridge is inserted into the disk unit.

• Do not use the cartridge under ambient

conditions of high humidity or wide

temperature fluctuations. Moisture from

condensation may make it impossible to read or

write data.

• Avoid inserting and ejecting the disk cartridge

more than is necessary.

• Always eject and remove the disk cartridge

from the disk unit after using it.

■ Storing disk cartridges

• Store the disk cartridges in their cases.

• Do not leave the cartridges exposed to direct

sunlight or excessive heat, like on the dashboard

or in the glove compartment of an automobile.

Do not store the disk cartridges under the

following conditions.

– Excessive dust and debris

– Exposure to direct sunlight

– Near a heat source

– High humidity

Chapter 4 Precautions 17

Protecting Your Data

The magneto-optical disk cartridges are equipped

with a DATA PROTECT switch (red tab) to

prevent accidental erasure of data on the disk or

inadvertent writing of unwanted data. Slide this

switch in the direction of the arrow as illustrated

below to enable the write protect function.

You can still read the data contained on the disk,

but will not be allowed to write on or erase the

disk. Return the switch to its original position to

disable the write protect.

Cleaning

DATA PROTECT

switch

Make it a practice to leave the write protection

enabled when you do not foresee the need to

write on the disk.

Cleaning a Disk

Dust and stains may accumulate on MO disks

when they are used for a long period of time. To

avoid resultant data read/write errors, use an

optional disk cleaner. To maintain the high

performance and prolong the useful life of your

MO disk, cleaning at least once every three

months is recommended.

■ Disk cleaning accessories

Use the following Sony disk cleaning kit or disk

cleaner (sold separately).

•MOA-D51 Disk Cleaning Kit

Do not use any other type of disk cleaner as it

may cause data read/write errors due to the

differences in disk surface characteristics. For

cleaning instructions, refer to the manual

supplied with each cleaning accessory.

Attention

In the disk unit, preventive measures are taken to

guard against dust. It is unnecessary to clean the

optical lens of your disk unit. Using a lens

cleaning cartridge may damage the disk unit.

18 Appendix

Appendix

Specifications

Disk Unit

■ Performance

Capacity

Per disk

9.1 Gbytes (ZCAV 4,096 bytes/sector)

8.6 Gbytes (ZCAV 2,048 bytes/sector)

9.1 Gbytes (ZCAV 1,024 bytes/sector)

9.1 Gbytes (ZCAV 512 bytes/sector)

5.2 Gbytes (ZCAV 2,048 bytes/sector)

4.8 Gbytes (ZCAV 1,024 bytes/sector)

4.1 Gbytes (ZCAV 512 bytes/sector)

2.6 Gbytes (ZCAV 1,024 bytes/sector)

2.3 Gbytes (ZCAV 512 bytes/sector)

Rotation speed

3,000 min

–1

(3,000 rpm)

3,300 min

–1

(3,300 rpm)

3,600 min

–1

(3,600 rpm)

Seek times (average)

25 ms (typical)

User data transfer rate

Continuous transfer rate

3.07 – 6.14 Mbytes/s

(4,096 bytes/sector)

2.87 – 5.84 Mbytes/s

(2,048 bytes/sector)

3.07 – 6.14 Mbytes/s

(1,024 bytes/sector)

3.07 – 6.14 Mbytes/s

(512 bytes/sector)

Burst transfer rate

20 Mbytes/s (using Ultra SCSI)

Host interface

SCSI-2 (Small Computer System Interface-2)

ANSI X3.131–1994

■ Operating environment

Installation

Horizontal (±5°)

Temperature

Operating

5 °C to 40 °C (41 °F to 104 °F)

(gradient 10° C/h or 18 °F/h)

Non-operating

– 30 °C to 60 °C (– 22 °F to 140 °F)

Relative humidity

Operating

10 % to 85 % (no condensation)

Non-operating

10 % to 90 %

■ Laser

Type

Semiconductor AlGaInP laser

Wavelength

661 nm ± 6 nm

Maximum output

40 mW CW

60 mW Pulse

■ Power supply and others

Power supply

100 – 240 V AC ±10%, 50/60 Hz ±5%

Current drain

0.60 – 0.35 A max

Maximum external dimensions (excluding

protruding parts and air duct)

211 × 70 × 293 mm (W/H/D)

(8

3

/8 × 2

7

/8 × 11

5

/8 inches)

Weight

4.9 kg (10.9 lb.)

Accessories

AC power cord (1)

Emergency eject tool (1)

User’s Guide (1)

MO Disk (1)

Formatting Utility (1)

Design and specifications are subject to change

without notice.

Appendix 19

Optional Accessories

MO disks

EDM-9100B (4,096 bytes/sector, 9.1 Gbytes)

EDM-8600B (2,048 bytes/sector, 8.6 Gbytes)

EM1-9100B (1,024 bytes/sector, 9.1 Gbytes)

EM5-9100B (512 bytes/sector, 9.1 Gbytes)

EDM-5200B (2,048 bytes/sector, 5.2 Gbytes)

EDM-4800B (1,024 bytes/sector, 4.8 Gbytes)

EDM-4100B (512 bytes/sector, 4.1 Gbytes)

EDM-2600B (1,024 bytes/sector, 2.6 Gbytes)

EDM-2300B (512 bytes/sector, 2.3 Gbytes)

Continuous composite write-once disks

CWO-9100B (4,096 bytes/sector, 9.1 Gbytes)

CWO-8600B (2,048 bytes/sector, 8.6 Gbytes)

CWO-5200B (2,048 bytes/sector, 5.2 Gbytes)

CWO-4800B (1,024 bytes/sector, 4.8 Gbytes)

CWO-4100B (512 bytes/sector, 4.1 Gbytes)

CWO-2600B (1,024 bytes/sector, 2.6 Gbytes)

CWO-2300B (512 bytes/sector, 2.3 Gbytes)

Disk Cleaning Kit

MOA-D51

20

AVERTISSEMENT

Afin de réduire les risques d’incendie ou

de choc électrique, n’exposez pas cet

appareil à la pluie ni à l’humidité.

Pour éviter toute électrocution, ne pas

ouvrir le boîtier. Confier l’entretien à un

technicien qualifié uniquement.

NOTICE

Utiliser le cordon d’alimentation approuvé par

l’organisation de contrôle appropriée pour les

pays auxquels le produit est destiné.

Règles de sécurité Sommaure

Comment utiliser ce Guide..................... 21

Chapitre 1 Introduction

Aperçu ...................................................... 22

Caractéristiques ........................................ 22

Disques compatibles ................................. 23

Configuration de système ......................... 24

Localisation et fonction des pièces ...... 25

Chapitre 2 Démarrage

Liste de contrôle des composants et

accessoires ...................................... 26

Connexion du lecteur ............................. 27

Réglage de l’adresse SCSI ..................... 27

Réglage des fonctions du lecteur.......... 28

Chapitre 3 Fonctionnement du lecteur

Insertion d’une cartouche disque.......... 29

Ejection d’une cartouche disque ........... 30

Chapitre 4 Précautions

A propos du lecteur ................................ 31

Sécurité ..................................................... 31

Prévention des dommages ........................ 31

Autres points à prendre en compte ........... 32

A propos des cartouches disques ........ 32

Protection des données ............................. 33

Entretien................................................... 33

Nettoyage des disques .............................. 33

Appendice

Spécifications .......................................... 34

Lecteur ...................................................... 34

Accessoires en option ............................... 35

Traitement des appareils électriques et

électroniques en fin de vie (Applicable

dans les pays de l’Union Européenne et

aux autres pays européens disposant de

systèmes de collecte sélective)

Ce symbole, apposé sur le produit ou

sur son emballage, indique que ce

produit ne doit pas être traité avec les

déchets ménagers. Il doit être remis à

un point de collecte approprié pour le

recyclage des équipements électriques

et électroniques. En s’assurant que ce produit est

bien mis au rebut de manière appropriée, vous

aiderez à prévenir les conséquences négatives

potentielles pour l’environnement et la santé

humaine. Le recyclage des matériaux aidera à

préserver les ressources naturelles. Pour toute

information supplémentaire au sujet du recyclage

de ce produit, vous pouvez contacter votre

municipalité, votre déchetterie ou le magasin où

vous avez acheté le produit.

La page charge ...

Sony RMO-S561 Le manuel du propriétaire

Sony RMO-S561 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents