Legrand LMSH-MCA140 Guide d'installation

Marque: Legrand

Modèle: LMSH-MCA140

Taper: Guide d'installation

Ce manuel convient également à

LMSH-MCA1XX DLM Shade Motor Control

Wattstopper

DLM Shade Motor Control Assembly

Installation Instructions

No: D000073 – 04/21 rev. 3

Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo: LMSH-MCA140, LMSH-MCA173

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

SPECIFICATIONS

Input Voltage ..............................................................24/36VDC

Connect to LMSH-PS602 or LMSH-PS610 Power Supply

UL/C-UL Ratings ......................36 VDC, 0.12 A, Class 2 Supply

Speed/Torque

LMSH-MCA140 ....................................... 38 RPM/10 N-cm

LMSH-MCA173 ....................................... 29 RPM/15 N-cm

Current Consumption ...............................................250mA, 6W

Connection to Shade Bus: ............. 4-Conductor wire whip with

.................. female terminal (power and data over four wires)

Cable Whip Length ...................................................... 36 inches

Minimum Shade Size ..........................................16 inches wide

Maximum Shade Size .......................15 foot wide by 20 foot tall

Motors Status LED .............................................Tri Color (RGB)

Environment:

Operating Temperature .......................32° to 120°F (0° to 50°C)

Storage Temperature ...................... -20° to 180°F (-28° to 82°C)

Relative Humidity .............................5 to 95% (non condensing)

IP Rating .............................................................................. IP44

UL/C-UL Listed under UL325, E514301. Indoor Use Only

DESCRIPTION AND OPERATION

The DLM shade motors (MCA or Motor Control Assembly) are part of a complete shade control system designed to make installation

and programming of motorized roller shades simple and easy. DLM motors have a unique counter-balance design that allows the

shades to be pulled into position or raised by using the hembar. Pulling on the shade hembar will not damage the motor.

The DLM shades motors have two different gear ratios to support shades of different sizes. The 40:1 gear ratio motors (LMSH-MCA140)

are used on smaller shades while the 73:1 gear ratio motors (LMSH-MCA173) are used on larger and coupled shades. For each shade

there is a counter-balance spring that is designed specifically for the weight of the shade and motor. The motor and spring assembly is

specified and tested by the factory. In the rare instance they have to be replaced in the field, be sure to use the same motor and spring

combination. Contact factory for assistance in getting replacement motors and spring assemblies

Using the patented Plug n’ Go (PnG) operation when the MCA is connected to the shade network (can be connected to the powered

system) the MCA will automatically join the network, set a default upper and lower shade limit, and be assigned to any shade switches

on the project. These settings can be customized later by using the Push n’ Learn (PnL) and Pull n’ Save (PnS) procedures found in

shade controller power supply or shade switch installation instructions.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be

followed including the following:

a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

b. Do not use outdoors.

c. Do not mount near gas or electric heaters.

d. Equipment should be mounted in locations and at heights where it will

not readily be subjected to tampering by unauthorized personnel.

e. The use of accessory equipment not recommended by the

manufacturer may cause an unsafe condition.

f. Do not use this equipment for other than intended use.

g. Installation should be performed by qualified service personnel.

SAVE THESE INSTRUCTIONS

No User Serviceable Parts”

“Installation shall be in accordance with all applicable regulations, local and all

NEC Codes.”

Coupler

Shade Bus

Whip

Crown

LED

Bracket Shaft

Antenna

Step 1 Remove the old MCA from the shade.

Step 2 Insert new MCA into shade in the same

end as it was removed.

Step 3 Before inserting the crown, be sure

to orientate the Antenna and Shade Bus

Whip relative to the Hembar as shown.

Step 4 Insert Crown completely into the shade

tube. Note that the LED should be below the

Bracket Shaft when installed into the brackets.

REPLACING AND INSTALLING THE MOTOR

Step 5 Connect the Shade Bus Whip to an

LMSH-SBE4, LMSH-PS602, or LMSH-PS610.

SETTING UP THE REPLACEMENT MCA IN THE DLM SHADE NETWORK

Once the MCA is connected and the system is powered up, the new MCA will be recognized by the shade controller and will be

controlled by all connected switches, based on the default Plug n’ Go operation for each switch model.

You may need to set the lower or upper shade limits, by using the Pull n’ Save procedure.

Finally, you can use Push n’ Learn™ technology to change the binding relationship between switch buttons and the new shade motor.

For detailed instructions on Plug n’ Go, Pull n’ Save, and Push n’ Learn, see the installation instructions for the LMSH-PS602 or

LMSH-PS610 shade controller power supplies, or the LMSH-SW10x Shade Switches. These guides can be downloaded from the

Legrand Shading Website.

LED Status Indicators

Off Shade is operating correctly and is not in any configuration mode.

Solid Red There is an error with shade. See Troubleshooting section.

Blinking Red 4 times per/second The system is in PnL mode.

Blinking Red 2 times per/second The system is in PnS mode.

TROUBLESHOOTING

LEDs on a shade switch

or motorized shade don’t

light

1. Check to see that the device is connected to the DLM Local Network.

2. Check for 36VDC input to the device: Plug in a different DLM device at the device location. If the

device does not power up, 36VDC is not present.

• Check the high voltage connections to the shade controller.

• If high voltage connections are good and high voltage is present, recheck DLM Local Network

connections between the device and the room controller(s).

LEDs turn ON and OFF

but shade doesn’t move

1. Make sure the DLM local network is not in PnS.

2. Check shade bus connections between shade controller and DLM motorized shades.

833.456.4291

www.legrand.us/shading-shading

No. D000073 – 04/21 rev. 3

Limited Lifetime Warranty

Legrand offers a Limited Lifetime Warranty

for window shade product, and/or specific

components of the window shade product to be

free from defects in materials and workmanship

under normal use. There are no obligations or

liabilities on the part of Legrand for consequential

damages arising out of, or in connection with,

the use or performance of this product or other

indirect damages with respect to loss of property,

revenue or profit, or cost of removal, installation

or reinstallation. For full warranty details visit

www.legrand.us/commercial-shading

Garantie à vie limitée

Legrand offre une garantie à vie limitée pour

le produit de store et / ou des composants

spécifiques du produit de store pour être exempts

de défauts de matériaux et de fabrication dans

des conditions normales d’utilisation. Il n’y a

aucune obligation ou responsabilité de la part

de Legrand pour les dommages consécutifs

résultant de, ou en relation avec l’utilisation

ou la performance de ce produit ou d’autres

dommages indirects en ce qui concerne la perte

de biens, de revenus ou de bénéfices, ou le coût

de l’enlèvement, installation ou réinstallation.

Pour plus de détails sur la garantie, visitez

www.legrand.us/commercial-shading

Garantia limitada de por vida

Legrand ofrece una garantía limitada de por

vida para el producto de sombra de ventana,

y / o componentes específicos del producto de

sombra de ventana para estar libres de defectos

en materiales y mano de obra bajo uso normal.

No hay obligaciones ni responsabilidades por

parte de Legrand por daños consecuentes

que surjan de, o en conexión con, el uso o

desempeño de este producto u otros daños

indirectos con respecto a la pérdida de

propiedad, ingresos o ganancias, o costo de

remoción, instalación o reinstalación Para

obtener detalles completos de la garantía, visite

www.legrand.us/commercial-shading

WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA

The design of this device complies with FCC and IC safety levels of radio frequency (RF) exposure for Mobile devices.

CAUTION: Changes or modifications to this device not expressly approved by Legrand could void the user’s authority to operate the equipment.

Mobile Device RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter.

FCC Notices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in an installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning this device off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer for help.

The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful

interference, and 2) this device must accept any interference received, including interference that may cause undesired operation

Cet appareil est conforme aux limites d’exposition aux Frequences Radio définies par les normes IC et FCC pour les appareils mobiles

ATTENTION: Tous changements ou modifications qui ne sont pas expressément approuvés par Legrand sont susceptibles de révoquer les droits

d’utilisation de cet équipement.

Déclaration d’exposition aux fréquences radio d’appareil mobile: Exposition fréquences radio - Cet appareil est seulement conçu pour usage

mobile. Au moins 20 cm de séparation doit être maintenue à tout instant entre l’appareil IPPAN3 et l’utilisateur.

Avis IC

Le présent appareil a été testé et entre dans la catégorie des appareils numériques de Classe B, selon la Section 15 de la réglementation de la IC. Ces

limites ont été conçues pour protéger les installations domestiques contre les interférences néfastes. Cet équipement génère, utilise et émet de l’énergie

sous forme de fréquences radio et, en cas de non-respect des instructions d’installation et d’utilisation, risque de provoquer des interférences radio. Il

n’existe cependant aucune garantie contre ces interférences.

En cas d’interférences radio ou télévisuelles, pouvant être vérifiées en allumant, puis en éteignant l’équipement, l’utilisateur est invité à essayer de

résoudre le problème de l’une des façons suivantes :

• Eloigner l’équipement du poste de réception ;

• Brancher l’équipement sur une prise appartenant à un circuit différent de celui du récepteur ;

• Demander de l’aide auprès du revendeur ou d’un technicien radio/TV

INDUSTRY CANADA

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.