Hitachi DH 24PB Manuel utilisateur

DH 24PB

MODEL ROTARY HAMMER

MODÈLE MARTEAU ROTATIF

MODELO MARTILLO GIRATORIO

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant

qu’ils utilisent l’outil motorisé.

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual before operating the power tool. Please keep this

manual available for others before they use the power tool.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar

en lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de que utilicen la

herramienta eléctrica.

2

English

CONTENTS

English

Page

IMPORTANT INFORMATION ............. 3

MEANINGS OF SIGNAL WORDS ...... 3

SAFETY ................................................... 4

GENERAL SAFETY RULES ................. 4

SPECIFIC SAFETY RULES AND SYMBOLS

..... 7

DOUBLE INSULATION FOR SAFER

OPERATION ..................................... 8

FUNCTIONAL DESCRIPTION ................ 9

MANE OF PARTS ................................ 9

SPECIFICATIONS ................................ 9

Page

ASSEMBLY AND OPERATION ............ 10

APPLICATIONS ................................. 10

PRIOR TO OPERATION ..................... 10

HOW TO USE .................................... 12

HOW TO USE THE CORE BIT (FOR LIGHT LOAD)

... 15

MAINTENANCE AND INSPECTION .... 17

ACCESSORIES ...................................... 18

STANDARD ACCESSORIES ............. 18

OPTIONAL ACCESSORIES ............... 18

PARTS LIST .......................................... 68

TABLE DES MATIERES

Français

Page

INFORMATIONS IMPORTANTES ....... 24

SIGNIFICATION DES MOTS

D’AVERTISSEMENT ......................... 24

SECURITE ............................................. 25

REGLES GENERALES DE SECURITE

..... 25

REGLES DE SECURITE SPECIFIQUES ET SYMBOLES

... 28

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR

........ 29

DESCRIPTION FONCTIONNELLE ........ 30

NOM DES PARTIES .......................... 30

SPECIFICATIONS .............................. 30

Page

ASSEMBLAGE ET FONCTIONNEMENT ....

31

APPLICATIONS ................................. 31

AVANT L’UTILISATION .................... 31

UTILISATION ..................................... 33

COMMENT UTILISER LA COURONNE (POUR

UNE CHARGE LEGERE)

.........................

37

ENTRETIEN ET INSPECTION ............... 39

ACCESOIRES ........................................ 40

ACCESSOIRES STANDARD ............. 40

ACCESSOIRES SUR OPTION ........... 40

LISTA DES PIÈCES ............................... 68

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE ............ 46

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ................................. 46

SEGURIDAD ......................................... 47

NORMAS GENERALES DE SEGURIDAD

... 47

NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD

..... 50

AISLAMIENTO DOBLE PARA OFRECER UNA

OPERACIÓN MÁS SEGURA

................... 51

DESCRIPCIÓN FUNCIONAL ................ 52

NOMENCLATURA ............................. 52

ESPECIFICACIONES .......................... 52

Página

MONTAJE Y OPERACIÓN ................... 53

APLICACIONES ................................. 53

ANTES DE LA OPERACIÓN .............. 53

COMO SE USA .................................. 55

MODO DE USAR LA BARRENA TUBULAR

(PARACARGAS LIGERAS)

................. 59

MANTENIMIENTO E INSPECCIÓN ..... 61

ACCESORIOS ....................................... 62

ACCESORIOS ESTÁNDAR ............... 62

ACCESORIOS OPCIONALES ............ 62

LISTA DE PIEZAS ................................. 68

3

English

IMPORTANT INFORMATION

Read and understand all of the operating instructions, safety precautions and warn-

ings in the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused

by the failure to observe basic safety rules or precautions. An accident can often be

avoided by recognizing a potentially hazardous situation before it occurs, and by

observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction

Manual and in the sections which contain the operation and maintenance instruc-

tions.

Hazards that must be avoided to prevent bodily injury or machine damage are iden-

tified by WARNINGS on the power tool and in this Instruction Manual.

Never use this power tool in a manner that has not been specifically recommended

by HITACHI, unless you first confirm that the planned use will be safe for you and

others.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could re-

sult in serious personal injury.

CAUTION indicates a hazardous situations which, if ignored, could result in moder-

ate personal injury, or could cause machine damage.

NOTE emphasizes essential information.

4

English

SAFETY

GENERAL SAFETY RULES

WARNING

: Read and understand all instructions.

Failure to follow all instructions listed below, may result in elec-

tric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the pres-

ence of flammable liquids, gases, or dust. Power tools create sparks which

may ignite the dust or fumes.

(3) Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) Double Insulated tools are equipped with a polarized plug (one blade is wider

than the other.) This plug will fit in a polarized outlet only one way. If the

plug does not fit fully in the outlet, reverse the plug. If it still does not fit,

contact a qualified electrician to install a polarized outlet. Do not change the

plug in any way. Double Insulation

eliminates the need for the three wire

grounded power cord and grounded power supply system.

(2) Avoid body contact with grounded surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is

grounded.

(3) Don’t expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

(4) Do not abuse the cord. Never use the cord to carry the tools or pull the plug

from a receptacle. Keep cord away from heat, oil, sharp edges or moving

parts. Replace damaged cords immediately. Damaged cords increase the

risk of electric shock.

(5) When operating a power tool outside, use an outdoor extension cord marked

“W-A” or “W”. These cords are rated for outdoor use and reduce the risk of

electric shock.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operat-

ing a power tool. Do not use tool while tired or under the influence of drugs,

alcohol, or medication. A moment of inattention while operating power tools

may result in serious personal injury.

5

English

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying

tools with your finger on the switch or plugging in tools that have the switch

on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or

a key that is left attached to a rotating part of the tool may result in personal

injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper foot-

ing and balance enables better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear protective grasses. Dust mask, non-

skid safety shoes, hard hat, or ear plugs must be used for appropriate condi-

tions.

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a

stable platform. Holding the work by hand or against your body is unstable

and may lead to lose of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool

will do the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be

controlled with the switch is dangerous and must be repaired.

(4) Disconnect the plug form the power source before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures

reduce the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hand of untrained users.

(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly main-

tained tools, with sharp cutting edges are less likely to bind and are easier to

control.

(7) Check for misalignment or binding of moving parts, breakage of parts, and

any other condition that may affect the tools operation. If damaged, have

the tool serviced before using. Many accidents are caused by poorly main-

tained tools.

(8) Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool, may become hazard-

ous when used on another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service

or maintenance performed by unqualified personnel could result in a risk of

injury.

6

English

(2) When servicing a tool, use only identical replacement parts. Follow instruc-

tions in the Maintenance section of this manual. Use of unauthorized parts

or failure to follow Maintenance Instruction may create a risk of electric shock

or injury.

6. Never touch moving parts.

Never place your hands, fingers or other body parts near the tool’s moving parts.

7. Never operate without all guards in place.

Never operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or

safety feature, be sure to replace the guard or safety feature before resuming

operation of the tool.

8. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended — for example — don’t use circular saw

for cutting tree limbs or logs.

9. Never use a power tool for applications other than those specified.

Never use a power tool for applications other than those specified in the Instruc-

tion Manual.

10. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or

throw the tool. Never allow the tool to be operated by children, individuals unfa-

miliar with its operation or unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition peri-

odically.

12. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools

should not be used until repaired.

13. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to yourself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

14. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all

times. Check for dust build-up frequently.

15. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and the motor may

burn out.

16. Never use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or other-

wise appears defective, stop using it immediately and arrange for repairs by a

Hitachi authorized service center.

7

English

17. Never leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

18. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently,

it may be deformed, cracked, or damaged.

19. Do not wipe plastic parts with solvent.

Solvents such as gasolie, thinner, benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where

the cutting tool may contact hidden wiring or its own cord. Contact with a “live”

wire will make exposed metal parts of the tool “live” and shock the operator.

2. Wear ear plugs when using the tool for extended periods. Prolonged exposure

to high intensity noise can cause hearing loss.

3. NEVER touch the tool bit with bare hands after operation.

4. NEVER wear gloves made of stuff liable to roll up such as cotton, wool, cloth or

string, etc.

5. ALWAYS attach the side handle and securely grip the Rotary Hammer.

6. ALWAYS be careful with buried object such as an underground wiring.

Touching these active wiring or electric cable with this tool, you may receive an

electric shock.

Comfirm if there are any buried object such as electric cable within the wall,

floor or ceiling where you are going to operate here after.

7. Definitions for symbols used on this tool

V ... volts

Hz ... hertz

A ... amperes

n

o ... no load speed

W ... watt

... Class II Consruction

- - -/min ... revolutions per minute

8

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insula-

tion design. “Double insulation” means that two physically separated insulation

systems have been used to insulate the electrically conductive materials connected

to the power supply from the outer frame handled by the operator. Therefore, either

the symbol “

” or the words and “Double insulation” appear on the power tool or

on the nameplate.

Although this system has no external grounding, you must still follow the normal

electrical safety precautions given in this Instruction Manual, including not using

the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble

this power tool, and only genuine HITACHI replacement parts should be in-

stalled.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy

water, and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the

plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS OF THIS TOOL!

9

English

Fig. 1

SPECIFICATIONS

Motor Single-Phase, Series Commutator Motor

Power Source Single-Phase, 115V 60Hz

Current 5.7A

Capacity Concrete: 1/8" ~ 15/16" (3.4mm ~ 24mm)

Steel: 1/2" (13mm)

Wood: 1-1/4" (32mm)

No-Load Speed 0 – 1050/min.

Full-load Impact Rate 4400/min.

Weight 5.1 lbs (2.3 kg)

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in

the safe operation and maintenance of the power tool.

Some illustrations in this Instruction Manual may show details or attachments

that differ from those on your own power tool.

NAME OF PARTS

Housing

Nameplate

Drill Bit

Front Cap

Grip

Depth Gauge

Side Handle

Lever

Switch

Change Lever

10

English

ASSEMBLY AND OPERATION

APPLICATIONS

Rotation and striking function

䡬 Drilling anchor holes

䡬 Drilling holes in concrete

䡬 Drilling holes in tile

Rotation only function

䡬 Drilling in steel or wood (with optional accessories).

䡬 Tightening machine screws, wood screws (with optional accessories).

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source re-

quirements specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a recep-

tacle while the switch is in the ON position, the power tool will start operating

immediately and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity. The extension cord should be kept as

short as practicable.

WARNING: Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired.

Contact a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a seri-

ous hazard.

5. Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

11

English

Fig. 3

Dust Cup

Dust Collector (B)

Drill bit

Part of SDS-plus shank

Grip

Front cap

Fig. 2

6. Mounting the drill bit (Fig. 2)

(1) To attach a drill bit (SDS-plus shank),

fully pull the grip in the direction of the

arrow as shown in Fig. 2 and insert the

drill bit as far as it will go while manu-

ally turning.

(2) By releasing the grip, the drill bit will

be secured.

(3) To remove the drill bit, fully pull the grip

in the direction of the arrow and pull

out the drill bit.

7. Installation of dust cup or dust col-

lector (B) (Optional accessories)

(Fig. 3, Fig. 4)

When using a rotary hammer for up-

ward drilling operations attach a dust

cup or dust collector (B) to collect dust

or particles for easy operation.

䡬 Installing the dust cup

Use the dust cup by attaching to the

drill bit a shown in Fig. 3.

When using a bit which has big diam-

eter, enlarge the center hole of the dust

cup with this rotary hammer.

䡬 Installing dust collector (B)

When using dust collector (B), insert

dust collector (B) from the tip of the bit

by aligning it to the groove on the grip

(Fig. 4)

CAUTION:

䡬 The dust cup and dust collector (B) are for exclusive use of concrete drilling

work. Do not use them for wood or metal drilling work.

䡬 Insert dust collector (B) completely into the chuck part of the main unit.

䡬 When turning the rotary hammer on while dust collector (B) is detached from a

concrete surface, dust collector (B) will rotate together with the drill bit. Make

sure to turn on the switch after pressing dust cup on the concrete surface.

(When using dust collector (B) attached to a drill bit that has more than 7-15/

32" (190 mm) of overall length, dust collector (B) cannot touch the concrete

surface and will rotate. Therefore please use dust collector (B) by attaching to

Fig. 4

12

English

drill bits which have 6-17/32" (166 mm), 6-19/64" (160 mm) and 4-21/64" (110

mm) overall length.

䡬 Dump particles after every two or three holes when drilling.

䡬 Please replace the drill bit after removing dust collector (B).

8. Selecting the driver bit

Screw heads or bits will be damaged unless a bit appropriate for the screw di-

ameter is employed to drive in the screws.

9. Confirm the direction of bit ro-

tation (Fig. 5)

The bit rotates clockwise (viewed from

the rear side) by pushing the R-side of

the reversing switch lever. The L-side

of the lever is pushed to turn the bit

counterclockwise.

HOW TO USE

CAUTION:

䡬 To prevent accidents, make sure to turn the switch off and disconnect the plug

from the receptacle when the drill pits and other various parts are installed or

removed. The power switch should also be turned off during a work break and

after work.

1. Switch operation

The rotation speed of the drill bit can be controlled steplessly by varying the

amount that the trigger switch is pulled. Speed is low when the trigger switch is

pulled slightly and increases as the switch is pulled more. To turn the switch

OFF, release the trigger switch to its original position.

2. Rotation + Striking

This rotary hammer can be set to rota-

tion and striking mode by turning the

change lever fully counterclockwise to

mark. (Fig. 6)

(1) Mount the drill bit.

(2) Pull the trigger switch after applying the

drill bit tip to the drilling position (Fig. 7)

(3) Pushing the rotary hammer forcibly is

not necessary at all. Pushing slightly so

that drill dust comes out gradually is

just sufficient.

Lever

Fig. 5

Fig. 6

Change Lever

Fig. 7

13

English

CAUTION:

䡬 When the drill bit touches an iron reinforcing rod, the bit will stop immediately

and the rotary hammer will react to revolve. Therefore please grip the side

handle and handle tightly as shown in Fig. 7.

3. Rotation only

The rotary hammer can be set to rota-

tion only mode by rotating the change

lever fully clockwise to

mark. (Fig. 8)

To drill a wood or metal material using

the separately sold drill chuck and chuck

adaptor, proceed as follows. Installing

drill chuck and chuck adaptor (Fig. 9):

(1) Attach the drill chuck to the chuck

adaptor.

(2) The part of the SDS-plus shank is the

same as the drill bit. Therefore, refer to

the item of “Mounting the drill bit” for

attaching it.

CAUTION:

䡬 Application of force more than necessary will not only reducing drilling effi-

ciency at all, but will deteriorate the tip edge of the drill bit and reduce the

service life of the rotary hammer in addition.

䡬 Drill bit may snap off while withdrawing the rotary hammer from the drilled

hole. For withdrawing, it is important to use a pushing motion.

䡬 Do not attempt to drill anchor holes or holes in concrete with the main unit in

the rotation only function.

䡬 Do not attempt to use the rotary hammer in the rotation and striking function

with the drill chuck and chuck adaptor attached. This would seriously shorten

the service life of every components of the machine.

4. When driving machine screws

(Fig. 10)

First, insert the bit into the socket in the

end of chuck adaptor (D).

Next, mount chuck adaptor (D) on the

main unit using procedures described

in 5 (1), (2), (3), put the tip of the bit in

the slots in the head of the screw, grasp

the main unit and tighten the screw.

Bit

Socket

Chuck Adaptor (D)

Front Cap

Grip

Fig. 10

Change lever

Fig. 8

Chuck Adaptor

Drill Chuck

Part of SDS-plus

shank

Front Cap

Grip

Fig. 9

14

English

CAUTION:

䡬 Exercise care not to excessively prolong driving time, otherwise, the screws

may be damaged by excessive force.

䡬 Apply the rotary hammer perpendicularly to the screw head when driving a

screw; otherwise, the screw head or bit will be damaged, or driving force will

not be fully transferred to the screw.

䡬 Do not attempt to use the rotary hammer in the rotation and striking function

with chuck adaptor (D) and bit attached.

5. When driving wood screws (Fig. 10)

(1) Selecting a suitable driver bit

Employ phillips screws, if possible, since the driver bit easily slips off the heads

of slotted-head screws.

(2) Driving in wood screws

䡬 Prior to driving in wood screws, make pilot holes suitable for them in the wooden

board. Apply the bit to the screw head grooves and gently drive the screws into

the holes.

䡬 After rotating the rotary hammer at low speed for a while until a wood screw in

partly driven into the wood, squeeze the trigger more strongly to obtain the

optimum driving force.

CAUTION:

䡬 Exercise care in preparing a pilot hole suitable for the wood screw taking the

hardness of the wood into consideration. Should the hole be excessively small

or shallow, requiring much power to drive the screw into it, the thread of the

wood screw may sometimes be damaged.

6. Using depth gauge (Fig. 11)

(1) Loosen the knob on the side handle,

and insert the depth gauge into the

mounting hole on the side handle.

(2) Adjust the depth gauge position ac-

cording to the depth of the hole and

tighten the knob bolt securely.

Mounting Hole

Depth Gauge

Knob on Side

Handle

Fig. 11

15

English

7. How to use the drill bit (taper shank)

and the taper shank adaptor.

(1) Mount the taper shank adaptor to the

rotary hammer. (Fig. 12)

(2) Mount the drill bit (taper shank) to the

taper shank adaptor. (Fig. 12)

(3) Turn the switch ON, and drill a hole in

prescribed depth.

(4) To remove the drill bit (taper shank),

insert the cotter into the slot of the taper

shank adaptor and strike the head of

the cotter with a hammer supporting

on the rests. (Fig. 13)

HOW TO USE THE CORE BIT (FOR LIGHT LOAD)

When boring penetrating large hole use the core bit (for light load). At that time use

with the center pin and the core bit shank provided as optional accessories.

1. Mounting

CAUTION:

䡬 Be sure to turn power OFF and discon-

nect the plug from the receptacle.

(1) Mount the core bit to the core bit shank.

(Fig. 14)

Lubricate the thread of the core bit

shank to facilitate disassembly.

(2) Mount the core bit shank to the rotary

hammer. (Fig. 15)

Fig. 12

Drill Bit

Taper shank

Adaptor

Front Cap

Grip

Cotter

Rests

Taper Snank Adaptor

Fig. 13

Fig. 14

Core Bit

Thread

Core Bit Shank

16

English

(3) Insert the center pin into the guide plate

until it stops.

(4) Engage the guide plate with the core

bit, and turn the guide plate to left or

right so that it does not fall even if it

faces downward. (Fig. 16)

2. How to bore (Fig. 17)

(1) Connect the plug to the power source.

(2) A spring is installed in the center pin.

Push it lightly to the wall or the floor

straight. Connect all over the surface

of the core bit tip and start operating.

(3) When boring about 3/16" (5 mm) in

depth the position of the hole will es-

tablish. Bore after that removing the

center pin and the guide plate from core

bit.

(4) Application of excessive force will not

only expedite the work, but will dete-

riorate the tip edge of the drill bit, re-

sulting in reduced service life of the ro-

tary hammer.

CAUTION:

䡬 When removing the center pin and the

guide plate, turn OFF the switch and

disconnect the plug form the recep-

tacle.

3. Dismounting. (Fig. 18)

Remove the core bit shank from the ro-

tary hammer and strike the head of the

core bit shank strongly two or three

times with the hammer holding the

core bit, then the thread becomes loose

and the core bit can be removed.

Fig. 15

Fig. 17

Fig. 16

Core Bit

Core Bit Tip

Guide Plate

Center Pin

Fig. 18

Core Bit shank

17

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning and degraded efficiency,

replace the drill bit with a new one or resharpening without delay when abra-

sion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that they are properly tight-

ened. Should any of the screws be loosened, retighten them immediately.

WARNING: Using this rotary hammer with loosen screws is extremely dan-

gerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power tool. Exercise due care

to ensure the winding does not become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection, carbon brush inspec-

tion and replacement on this tool should ONLY be performed by a HITACHI AU-

THORIZED SERVICE CENTER.

5. How to replace grease

Low viscosity grease is applied to this rotary hammer so that it can be used for

a long period without replacing the grease. Please contact the nearest service

center for grease replacement when any grease is leaking from loosened screw.

Further use of the rotary hammer despite the grease shortage causes seizure to

reduce the service life.

CAUTION: A specific grease is used with this machine, therefore, the normal

performance of the machine may be badly affected by use of other

grease. Please be sure to let one of our service agents undertake

replacement of the grease.

6. Service and repairs

All quality power tools will eventually require servicing or replacement of parts

because of wear from normal use. To assure that only authorized replacement

parts will be used, all service and repairs must be performed by a HITACHI AU-

THORIZED SERVICE CENTER, ONLY.

18

English

ACCESSORIES

WARNING: Accessories for this power tool are mentioned in this Instruction

Manual.

The use of any other attachment or accessory can be dangerous

and could cause injury or mechanical damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1)Case (Molded plastic) (Code No. 307786) ...............................................................1

(2)Side Handle (Code No. 303659) ...............................................................................1

(3)Depth Gauge (Code No. 303709) .............................................................................1

1. Drilling anchor holes (Rotation + Striking)

䡬 Drill Bit (Slender shaft)

(1) Drill Bit (Slender

Shaft)

(2) Adaptor for slender shaft

(SDS-plus shank)

(1) Drill Bit (Slender Shaft)

(2) Adaptor for

Slender Shaft

Outer diameter Effective Length Overall Length Code No. Code No.

1/8" 1-25/32" 3-35/64"

306369

(3.4mm) (45mm) (90mm)

306370

9/64" 1-25/32" 3-35/64"

306368

(3.5mm) (45mm) (90mm)

䡬 Drill Bit (Taper shank) and taper shank adaptor

(1) Drill Bit (Taper Shank)

(2) Taper Shank Adaptor

(SDS-plus shank)

Cotter (Code No. 944477)

OPTIONAL ACCESSORIES...........sold separately

19

English

Taper mode Code No. Applicable drill bit

7/16" (11 mm)

31/64" (12.3 mm)

303617

1/2" (12.7 mm)

9/16" (14.3 mm)

73/128" (14.5 mm)

11/16" (17.5 mm)

303618 27/32" (21.5 mm)

A-taper 303619

B-taper 303620

External dia. Code No.

7/16"

944460

(11 mm)

31/64"

944461

(12.3 mm)

1/2"

993038

(12.7 mm)

9/16"

944462

(14.3 mm)

73/128"

944500

(14.5 mm)

11/16"

944463

(17.5 mm)

27/32"

944464

(21.5 mm)

Morse taper

(No. 1)

Drill bit

(Taper

shank)

䡬 1/2" (13 mm) Hammer Drill chuck and Chuck wrench

For drilling operations when using a straight shank bit for impact driling with a

rotary hammer

1/2" (13 mm) Hammer Drill

Chuck (SDS-plus shank)

(includes Chuck wrench)

Chuck wrench

Name Code No.

1/2" (13 mm) Hammer Drill Chuck 303332

Chuck wrench 303334

Rubber Cap 303335

2. Knock-in anchor (Rotation + Striking)

Anchor Setter (for anchor setting)

(SDS-plus shank)

Impact Drill

Application

Straight shank Bit













Taper shank adaptor formed A-

taper or B-taper is provided as an

optional accessory, but drill bit for

it is not provided.

Morse taper

(No. 2)

Drill bit

(Taper

shank)

20

English

Anchor size

W 1/4" W 5/16" W 3/8"

(6.3 mm) (8 mm) (9.5 mm)

Overall Length

10-15/64" 10-15/64" 6-19/64" 10-15/64"

(260 mm) (260 mm) (160 mm) (260 mm)

Code No. 302976 302975 303621 302974

Anchor size

W 1/4" W 5/16" W 3/8"

(6.3 mm) (8 mm) (9.5 mm)

Overall Length

10-15/64" 10-15/64" 6-19/64" 10-15/64"

(260 mm) (260 mm) (160 mm) (260 mm)

Code No. 302979 302978 303622 302977

Anchor setting adaptor

(for manual hammer)

<Outer wedge type with

the female screw>

Anchor size Code No.

W1/4"

971794

(6.3 mm)

W5/16"

971795

(8 mm)

W3/8"

971796

(9.5 mm)

W1/2"

971797

(12.7 mm)

W5/8"

971798

(15.9 mm)

<Inner wedge type with

the headless screw>

Anchor size Code No.

W1/4"

971799

(6.3 mm)

W5/16"

971800

(8 mm)

W3/8"

971801

(9.5 mm)

W1/2"

971802

(12.7 mm)

W5/8"

971803

(15.9 mm)

3. Large hole boring (Rotation + Striking)

Guide

Plate

Center pin Core Bit

Core bit Shank

(SDS-plus shank)

La page charge ...

Hitachi DH 24PB Manuel utilisateur

Ce manuel convient également à

Hitachi DH 24PB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents