Stratus ftServer V 2302 Site Planning Manual

Stratus Technologies

R624-04

Stratus

®

ftServer

®

V 2302, V 4304, and V 6308

Systems: Site

Planning Guide

Notice

The information contained in this document is subject to change without notice.

UNLESS EXPRESSLY SET FORTH IN A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED

REPRESENTATIVE OF STRATUS TECHNOLOGIES, STRATUS MAKES NO WARRANTY OR REPRESENTATION

OF ANY KIND WITH RESPECT TO THE INFORMATION CONTAINED HEREIN, INCLUDING WARRANTY OF

MERCHANTABILITY AND FITNESS FOR A PURPOSE. Stratus Technologies assumes no responsibility or obligation

of any kind for any errors contained herein or in connection with the furnishing, performance, or use of this document.

Software described in Stratus documents (a) is the property of Stratus Technologies Bermuda, Ltd. or the third party,

(b) is furnished only under license, and (c) may be copied or used only as expressly permitted under the terms of the

license.

Stratus documentation describes all supported features of the user interfaces and the application programming

interfaces (API) developed by Stratus. Any undocumented features of these interfaces are intended solely for use by

Stratus personnel and are subject to change without warning.

This document is protected by copyright. All rights are reserved. Stratus Technologies grants you limited permission to

download and print a reasonable number of copies of this document (or any portions thereof), without change, for your

internal use only, provided you retain all copyright notices and other restrictive legends and/or notices appearing in the

copied document.



Stratus, the Stratus logo, ftServer, the ftServer logo, Continuum, StrataLINK, and StrataNET are registered trademarks

of Stratus Technologies Bermuda, Ltd.



The Stratus Technologies logo, the Continuum logo, the Stratus 24 x 7 logo, ActiveService, ftScalable, and ftMessaging

are trademarks of Stratus Technologies Bermuda, Ltd.



RSN is a trademark of Lucent Technologies, Inc.

All other trademarks are the property of their respective owners.



Manual Name: Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning Guide

Part Number: R624

Revision Number: 04 

OpenVOS Release Number: 18.0.0 

Publication Date: December 2018

Stratus Technologies, Inc.

5 Mill and Main Place, Suite 500

Maynard, Massachusetts 01754-2660

Contents iii

Contents

Preface vii

1. Site Planning for ftServer V 2302, V 4304, and V 6308 Systems 1-1

Site Planning Overview 1-1

Site Planning for Fault-Tolerant Systems 1-2

Planning for Cables 1-3

Site Planning Checklist 1-5

Preparing to Install a System 1-7

Preparing to Take Delivery of a System 1-8

Moving the System to the Installation Site 1-8

System Documentation 1-9

Safety Notices 1-10

Consignes de sécurité 1-13

2. AC Power Planning 2-1

AC Power Overview 2-1

Redundant Power Sources 2-1

AC Power and HVAC Worksheets 2-2

Selecting a UPS Unit for ftServer Systems 2-4

AC Power Connections to Qualified UPS Models 2-4

Power Cord Summary 2-6

Main Cabinet Ground Cables 2-6

3. Space and Component Location Planning 3-1

RSN Connections 3-1

Fibre Channel Connections 3-2

UPS Connections 3-3

Component Location and Cabling Summary 3-3

Room Requirements 3-5

Cabinet Mounting and Leveling Considerations 3-8

Creating a Floor Plan 3-9

Contents

iv Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning Guide (R624)

4. Other Infrastructure Requirements 4-1

Telephone Lines 4-1

Network Connections 4-2

Site Ethernet Networks 4-2

Ethernet Subnet Requirements 4-3

Maintenance Network 4-3

System PC Console 4-4

5. Supported Configurations 5-1

Cabinet Configurations 5-1

Appendix A. System Specifications A-1

System Specifications A-1

AAP87600V PDU Specifications A-6

Appendix B. Electrical Circuit and Wiring Information B-1

Fault Protection Requirements B-1

Grounding Considerations B-1

Circuit Wiring Diagrams B-2

Electrical Power Connectors B-8

Appendix C. Standards Compliance C-1

Electronic Interference, Immunity, Safety, and Noise Level 

Standards Compliance C-1

Toxic and Hazardous Substances and Elements Disclosure C-5

Index Index-1

Figures v

Figures

Figure 1-1. AA-E97900 RSN Console Server Connections (Internet) 1-4

Figure 1-2. AA-E97900 Console Server Connections (Modem) 1-5

Figure 3-1. Space-Planning Considerations 3-8

Figure 3-2. System Equipment Templates 3-10

Figure 3-3. Site-Layout Grid 3-11

Figure 5-1. Base ftServer V 4304 or V 6308 System 5-2

Figure 5-2. Fully Configured ftServer V 4304 or V 6308 System 5-3

Figure 5-3. ftServer V 2302 System Without Network I/O Enclosure 5-4

Figure A-1. CPU-I O Enclosures: Front View A-2

Figure A-2. ftServer CPU-I O Enclosures: Rear View A-2

Figure A-3. AAP87600V PDU A-6

Figure B-1. Star Ground Example B-2

Figure B-2. Power Input Labeling B-3

Figure B-3. Single-Phase 120V AC Circuit Connection B-3

Figure B-4. Single-Phase 240V AC Circuit Connection B-4

Figure B-5. Split-Phase 120/240 Volts AC Circuit Connection B-5

Figure B-6. Three-Phase 208V AC, Y-, or D-Source Circuit 

Connection, Phase-to-Phase B-6

Figure B-7. Three-Phase 380V AC, Y-, or D-Source Circuit 

Connection, Phase-to-Neutral B-7

vi Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning Guide (R624)

Tables

Table 1-1. Ethernet PCI Adapters 1-6

Table 1-2. ftServer V 2302, V 4304, and V 6308 System 

Documentation 1-9

Table 2-1. Worksheet for Planning Site AC Outlets and Cord Lengths 2-3

Table 2-2. Work Sheet for Site AC Power and HVAC Requirements 2-4

Table 2-3. UPS to PDU AC Power Cords for Qualified UPS Models 2-5

Table 2-4. Power Cords 2-6

Table 2-5. Main Cabinet Ground Cable 2-6

Table 3-1. Cord and Cable Summary 3-3

Table 3-2. Location of V Series System Components 3-4

Table 4-1. Ethernet Subnet Requirements 4-3

Table A-1. Cabinet Dimensions A-3

Table A-2. V 2302, V 4304, and V 6308 System CPU-I O Enclosure: 

Specifications A-4

Table A-3. AAP87600V PDU: Specifications A-7

Table B-1. Connectors for AC Power Outlets B-8

Table C-1. Compliance Standards for ftServer V 2302, V 4303, 

and V 6308 Systems (Class A) C-2

Preface vii

Preface

The Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning

Guide

(R624) documents the site requirements and customer responsibilities related

to preparing a site for the installation of ftServer V

2302, V 4304, and V 6308 systems.

This document is intended for those responsible for preparing a site for the installation

of an ftServer V

2302, V 4304, or V 6308 system.

Revision Information

This document is a revision. This revision incorporates support for

ftScalable

Storage G2 systems on ftServer V 2302, V 4304, and V 6308 systems on a

qualified release of OpenVOS Release 18.0.x.

NOTE

Contact your account representative for information about

which specific release of OpenVOS Release 18.0.x

supports ftScalable Storage G2 systems.

Notation Conventions

This document uses the notation conventions described in this section.

Warnings, Cautions, and Notes

Warnings, cautions, and notes provide special information and have the following

meanings:

WARNING

!

A warning indicates a hazardous situation that, if not

avoided, could result in death or serious injury.

AVERTISSEMENT

!

Un avertissement indique une situation dangereuse qui, si

pas évitée, pourrait entraîner la mort ou des blessures

graves.

Preface

viii Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning Guide (R624)

CAUTION

!

A caution indicates a hazardous situation that, if not

avoided, could result in minor or moderate injury.

MISE EN GARDE

!

Une mise en garde indique une situation dangereuse qui,

si pas évitée, pourrait entraîner des blessures mineures

ou modérées.

NOTICE

A notice indicates information that, if not acted on, could

result in damage to a system, hardware device, program,

or data, but does not present a health or safety hazard.

NOTE

A note provides important information about the operation

of an ftServer system or related equipment or software.

Getting Help

If you have a technical question about ftServer system hardware or software, try these

online resources first:

 Online documentation at the StrataDOC Web site. Stratus provides

complimentary access to StrataDOC, an online-documentation service that

enables you to view, search, download, and print customer documentation. You

can access StrataDOC at the following Web site:

http://stratadoc.stratus.com

 Online support from Stratus Customer Service. You can find the latest technical

information about an ftServer system in the Stratus Customer Service Portal at the

following Web site:

http://www.stratus.com/go/support

The Service Portal provides access to Knowledge Base articles for all Stratus

product lines. You can locate articles by performing a simple or advanced keyword

search, viewing recent articles or top FAQs, or browsing a product and category.

To log in to the Service Portal, enter your employee user name and password or, if

you have not been provided with a login account, click Register Account. When

Preface

Preface ix

registering a new account, ensure that you specify an email address from a

company that has a service agreement with Stratus.

If you cannot resolve your questions with these online self-help resources, and the

ftServer system is covered by a service agreement, contact the Stratus Customer

Assistance Center

(CAC) or your authorized Stratus service representative.To contact

the CAC, use the Service Portal to log a support request. Click Customer Support and

Add Issue, and then complete the Create Issue form. A member of our Customer

Service team will be glad to assist you.

Commenting on This Manual

You can comment on this manual using one of the following methods. When you

submit a comment, be sure to provide the manual’s name and part number, a

description of the problem, and the location in the manual where the affected text

appears.

 From StrataDOC, click the site feedback link at the bottom of any page. In the

pop-up window, answer the questions and click Submit.

 From any email client, send email to [email protected].

 From the Stratus Customer Service Portal, log on to your account and create a new

issue.

Stratus welcomes any corrections and suggestions for improving this manual.

Regulatory Notice

Appendix C, “Standards Compliance” provides all regulatory notices.

Preface

x Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning Guide (R624)

Site Planning for ftServer V 2302, V 4304, and V 6308 Systems 1-1

Chapter 1

Site Planning for ftServer V 2302,

V

4304, and V 6308 Systems1-

For an overview of required information and tasks you need to perform to prepare a site

for ftServer V

2302, V 4304, and V 6308 systems, see:

 “Site Planning Overview” on page 1-1

 “Site Planning for Fault-Tolerant Systems” on page 1-2

 “Planning for Cables” on page 1-3

 “Site Planning Checklist” on page 1-5

 “Preparing to Install a System” on page 1-7

 “System Documentation” on page 1-9

 “Safety Notices” on page 1-10

Site Planning Overview

Site planning for fault-tolerant systems includes:

 Electrical power planning

Provide electrical power sources that meet the requirements of the system and

optional components, including the purchase of a qualified

uninterruptible power

supply (UPS).

 Space planning

Plan the location of the system and external components to accommodate the

lengths of the connecting cables.

Provide adequate space for the system or cabinet and for a desk or table to

accommodate components outside a cabinet. Also provide enough space for

servicing the systems and components.

Provide an environment that meets the system's requirements for ambient

temperature and air quality.

Site Planning for Fault-Tolerant Systems

1-2 Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning Guide (R624)

 Other Infrastructure requirements

Understand Ethernet requirements. Provide sufficient network and telephone

connection points.

Provide a PC to act as a system PC console. Stratus provides a serial cable for

connecting the PC to the server. You must provide an Ethernet cable to connect

the system PC console to the ftServer system.

Use the “Site Planning Checklist” on page 1-5 to track your site preparation progress.

For information about obtaining documents related to your ftServer system, see

“System Documentation” on page 1-9.

During the site planning and preparation processes, work closely with your facilities

group or contractor to determine space, power, and environmental requirements. Enlist

their help to provide a suitable location with sufficient alternating current (AC) power,

heating, ventilation and air conditioning (HVAC) capabilities, and network and

telephone connections.

If your system is covered by a service agreement and you need help with site planning,

contact the Stratus Customer Assistance Center

(CAC) or your authorized Stratus

service representative. If you have a contract with the CAC or your authorized Stratus

service representative to install the system, contact them after you have prepared the

installation site and moved the system to the site. For more information about the CAC,

see the

http://www.stratus.com/support/cac/ Web site.

See Chapter 5, “Supported Configurations” for illustrations of the rack configurations of

your ftServer system and other rack-mounted components, and Appendix A, “System

Specifications” for the specifications of the base ftServer systems and of PDUs. See

the Stratus ftServer Systems: Peripherals Site Planning Guide (R582) for

specifications of other components, both rack-mounted and external to the rack.

Site Planning for Fault-Tolerant Systems

Consider the following specific fault-tolerant features of ftServer systems as you plan

the site:

 Lockstep technology means that the systems contain redundant hardware. The

systems contain two enclosures, each containing a full computing environment that

consists of a CPU element and an I/O element.

If a component in a CPU element malfunctions, the corresponding CPU element in

the other enclosure, which is processing the same information in lockstep,

continues processing without interruption. If a component in the I/O element

malfunctions, the system fails operation over to the corresponding element in the

other enclosure and continues to operate normally. The only consequences are

Planning for Cables

Site Planning for ftServer V 2302, V 4304, and V 6308 Systems 1-3

that the system is less fault tolerant, and any I/O throughput distributed between

the enclosures may be reduced. To restore full fault tolerance, an enclosure can be

replaced without taking the system offline.

 ftServer systems can connect to the Remote Service Network (RSN).

Connecting a system to the RSN allows the CAC to remotely diagnose,

troubleshoot, and resolve problems online.

Your system connects to the RSN by an AA-E97900 RSN console server connected

either to the Internet or to an AA-C72100 modem. See

“RSN Connections” on page 3-1

for more information.

Planning for Cables

At sites with solid (non-raised) floors, the cables exit from the top of the cabinet and are

routed along the ceiling.

At sites with raised floors, the cables exit from the bottom rear of the cabinet and are

routed under the floor.

To accommodate cables from your system, make sure to provide:

 One or two telephone lines as described in “Telephone Lines” on page 4-1:

 Ethernet ports, switches, or hubs, as needed

 Two UPS units, within reach of the power cords from the system or PDUs

 For external components, AC wall outlets within reach of the power cords from the

components

Make sure that cables you plan to connect to the system are long enough to reach

between the system and external components or connections. For information about

specific cables and power cords, see the following:

 “Power Cord Summary” on page 2-6

 Chapter 3, “Space and Component Location Planning”

 Stratus ftServer Systems: Peripherals Site Planning Guide (R582) for information

about cable lengths for peripheral components

Planning for Cables

1-4 Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning Guide (R624)

Figure 1-1 shows cabling considerations for systems using the AA-E97900 RSN

console server to connect to the Internet.

Figure 1-1. AA-E97900 RSN Console Server Connections (Internet)

Overhead

cable

tray

Cable

ladder

Ethernet

Future

expansion

System PC

console

vos237a

RSN

console server

Ethernet

Serial

UPS

units

Site Planning Checklist

Site Planning for ftServer V 2302, V 4304, and V 6308 Systems 1-5

Figure 1-2 shows cabling considerations for systems using the AA-E97900 RSN

console server to connect to a modem.

Figure 1-2. AA-E97900 Console Server Connections (Modem)

Site Planning Checklist

Referring to the information in this document, answer the following questions:

❏ Do you have a telephone and telephone line near the operator’s station for voice

communications when calling for support?

Planning for RSN Connectivity

❏ If using the AA-E97900 console server to connect to the Internet, do you have an

Ethernet connection to the Internet and do you have OpenVOS Release 17.1.0 or

later installed?

❏ If using the AA-E97900 console server to connect to a modem, do you have an

external telephone line available for the RSN modem?

Overhead

cable

tray

Cable

ladder

Phone line

Future

expansion

System PC

console

RSN modem

vos123d

RSN

console server

Ethernet

Serial

UPS

units

Site Planning Checklist

1-6 Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning Guide (R624)

NOTE

A dedicated phone line for the RSN modem provides the

most reliable service. RSN calls routed through a PBX

may be slow due to load on the PBX, or may not complete

successfully due to disconnections. If you must use a

PBX, do not route the telephone extension through a

switchboard; instead, provide a direct-dial analog number.

Planning for Optional Components

❏ The system contains four embedded 10/100/1000 megabits-per-second (Mbps)

Ethernet ports. Will your system additionally include any of the following PCI

adapters for network communications? If so, in

Table 1-1, indicate the total number

of ports, and plan network connections for all Ethernet ports you will use.

❏ Do you have a system PC console located at the installation site? Plan to keep the

console located with the system.

❏ To plan for storage enclosures in your system, see the Stratus ftServer Systems:

Peripherals Site Planning Guide

(R582) for descriptions of the enclosures and the

names of the required PCI adapters.

Planning AC Power

❏ Have you selected and purchased two UPS units for each ftServer system?

❏ What optional components will you use?

❏ What are the HVAC and AC power requirements of all optional components?

❏ What are the lengths and types of the power cords that are provided for the optional

components?

❏ What type of AC receptacles do you need to provide?

❏ Is the AC power service wired properly?

Planning Space for Your System

❏ Will your system and its external components fit where you plan to place them?

❏ What are the lengths and types of the interface and communications cables that

will connect to your system?

Table 1-1. Ethernet PCI Adapters

Adapter Total Number of Ports

U776V Quad-Port Fiber Gigabit Ethernet Adapter

U578V Quad-Port Copper Gigabit Ethernet Adapter

Preparing to Install a System

Site Planning for ftServer V 2302, V 4304, and V 6308 Systems 1-7

❏ Have you created a sketch of how you plan to arrange the system at the installation

site? Consider the available cable lengths, the placement of external devices, and

the location of network and voice communication connections.

On the sketch, show the following:

 Location of the system and its external components

 Power cords, and telephone and interface cables

 Locations of AC power receptacles, phone jacks, Ethernet jacks, switches, and

hubs

NOTE

Make sure that all cords and cables are long enough to

reach between their respective components and

connectors. Route all cables out of the way of foot traffic.

Working with Other Groups

❏ Have you provided your facilities group and contractors with the sketch of how you

plan to arrange the system and copies of the following?

 “Redundant Power Sources” on page 3-1

 Appendix B, “Electrical Circuit and Wiring Information”

 Any notes you have about site planning

❏ Have you reviewed and discussed the requirements with the facilities personnel

and contractors to ensure that all site modifications are understood and

implemented?

If you have any questions about the number and types of components, contact your

Stratus account executive or distributor.

Preparing to Install a System

To prepare for the installation of a system by a field engineer, perform the following

tasks:

1. Complete all site preparation work, as described in “Preparing to Take Delivery of

a System” on page 1-8.

2. Take delivery of the system.

3. Move the system to its installation site, as described in “Moving the System to the

Installation Site” on page 1-8.

Preparing to Install a System

1-8 Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning Guide (R624)

Preparing to Take Delivery of a System

Before you take delivery of your system, perform the following tasks:

1. Secure traffic permits for the delivery vehicle and security clearances for moving

the shipping container within your facility if necessary.

2. Determine a suitable delivery site with enough space for unloading the system.

3. Make sure that the delivery site will accommodate the delivery vehicle.

NOTE

Depending on the system configuration and the

components you have ordered, a separate carton

containing components may be shipped with your system.

When your system arrives, perform the following tasks:

 Contact the CAC.

 Check the Tip-N-Tell and Shockwatch motion sensors to determine if they have

been activated. If a sensor has been activated, or if there is any damage, report it

immediately to the carrier and to the CAC.

 Check the packing list. If you received the wrong shipment, or if the shipment is

incomplete, report it immediately to the carrier and to the CAC.

Moving the System to the Installation Site

Before moving your system to the installation site, perform the following tasks:

NOTE

Moving a system requires two able-bodied persons.

1. Obtain a forklift or pallet jack to move your system from the delivery area to the

installation site.

2. Check the dimensions of doorways and the load capacities of floors and elevators.

You should walk the path over which you will move the system to ensure that it can

be easily moved to the installation site. If your system will not fit through the

doorways, you may need to arrange for rigging.

System Documentation

Site Planning for ftServer V 2302, V 4304, and V 6308 Systems 1-9

NOTE

Each cabinet is shipped on a pallet that is slightly larger

than a standard door opening. A standard door opening is

35 in. (89 cm) wide, and all pallets are 41.0 in. (104.2 cm)

wide by 53.0 in. (134.6 cm) deep.

3. If you are moving the system across a raised floor, lay plywood on the raised floor

to prevent floor tiles from popping up when you move the system.

4. Move the system as close to the installation site as possible.

System Documentation

Tabl e 1-2 lists the hardware documents for ftServer V 2302, V 4304, and V 6308

systems, and the tasks described in each document.

Table 1-2. ftServer V 2302, V 4304, and V 6308 System Documentation

Document Task

Stratus ftServer Systems: PCI Adapter

Guide

(R461)

Install, configure, replace, or troubleshoot PCI

adapters

Stratus ftServer Systems: Peripherals Site

Planning Guide

(R582)

Find information about optional equipment that you

have ordered with your system that is needed to

complete site preparation

Stratus ftServer V 2302, V 4304, and V 6308

Systems: Site Planning Guide

(R624)

Prepare a site for installation of your ftServer

system

Stratus ftServer V 2302, V 4304, and V 6308

Systems: Operation and Maintenance

Guide

(R625)

Start up, shut down, and operate your system 



Troubleshoot system hardware



Remove and replace CRUs, including PCI

adapters

Read Me First: Moving V 2302, V 4304, and

V

6308 Systems to the Installation Site (R623)

Inspect and unpack ftServer system hardware

Safety Notices

1-10 Stratus ftServer V 2302, V 4304, and V 6308 Systems: Site Planning Guide (R624)

Safety Notices

WARNING

!

Risk of explosion if battery is replaced by an incorrect

type. Dispose of used batteries according to the

instructions provided with the battery.

WARNING

!

If you receive locking power cords with your system, do

not substitute other power cords. Use of the locking power

cords ensures proper grounding of the system.

WARNING

!

The system uses two power cords to provide redundant

sources of power. To fully remove power from a system,

disconnect both power cords. To reduce the risk that

electrical shock could injure a person or damage the

system, exercise caution when working in the unit even

when only one power cord is connected.

WARNING

!

To prevent a cabinet from tipping over and injuring a

person or damaging the system, start installing systems

from the bottom of the cabinet upward.

WARNING

!

If you replace the modem cable supplied by Stratus, use

a cable with a gauge of at least 26 AWG to prevent fire.

WARNING

!

To avoid fire, electric shock, and equipment breakdown,

prevent water or foreign objects from getting into the

equipment. Do not let water or foreign objects, such as

pins or paper clips, enter the equipment.

WARNING

!

To prevent fire or current leakage, do not plug the power

cord into a nonconforming outlet. Use a power outlet with

La page charge ...

Stratus ftServer V 2302 Site Planning Manual

Ce manuel convient également à

Stratus ftServer V 2302 Site Planning Manual

dans d''autres langues

Autres documents