Classic Flame 73238 Manuel utilisateur

Classic Flame
Marque
Classic Flame
Modèle
73238
Taper
Manuel utilisateur

Ce manuel convient également à

1
ATTENTION
IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL
OR CALL CUSTOMER SERVICE BEFORE YOU RETURN
THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.
For Customer Service: XXXtwinstarhome.com
Call: (0808) 101 - 6215
ATENCIÓN
SI TIENE ALGÚN PROBLEMA O PREGUNTAS,
ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO
DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER
ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.
Servicio de atención al cliente: XXXtwinstarhome.com
Línea para llamadas: (0808) 101 - 6215
STOP
STOP
PARE
PARE
ATTENTION
SI VOUS AVEZ DES PROBLÈMES OU DES QUESTIONS,
ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE
SERVICE À LA CLIENTÈLE AVANT DE RETOURNER
CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.
Pour le service à la clientèle : XXXtwinstarhome.com
Composez le: (0808) 101 - 6215
ARRÊT
ARRÊT
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
1
ELECTRIC FIREPLACE MANTEL
28WM4311
ASSEMBLY INSTRUCTION
Requires-Electric Fireplace Requires-Electric Fireplace
Insert with HeaterInsert with Heater
ZZZtwinstarhome.com
Call: (0808) 101 - 6215
ATTENTION
For Customer Service:
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China
Printed in China
Españo p. 6
Français p. 11
2
Part Description Quantity
A Hearth/Base 1
B Left Front Panel 1
C Right Front Panel 1
D Center Front Panel 1
E Left Side Panel 1
F Right Side Panel 1
G Mantel/Top 1
PACKAGE CONTENTS
G
D
B
A
E
C
F
3
HARDWARE CONTENTS
Part
Description
Bolt
Washer
Wood Dowel
19
19
18
Quantity
Picture
(Shown to size)
BB
CC
AA
SAFETY INFORMATION
WARNING
• Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.
Make sure you do not discard the hardware.
CAUTION
• Use care in assembling your new fireplace. Take your time and use the hardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.
• Do not sit on any part of the mantel.
• All panels are labeled left and right as viewed from the front of unit.
Touch-up Pen
Model No. W3348
1
ZZ
W3348
4
ASSEMBLY INSTRUCTIONS
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 Minutes
Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife
Fig. 1
Fig. 2
C
F
E
B
Hardware Used
Hardware Used
BB
BB
AA
AA
CC
CC
Bolt
Bolt
x 2
x 8
Washer
Washer
x 2
x 8
Wood Dowel
Wood Dowel
x 4
x 4
AA
BB
A
CC
CC
CC
BB
AA
1. Locate Hearth/Base (A) and set out fi nished side
up on the fl oor.
Locate Left Front Panel (B) and Right Front Panel
(C), insert one Wood Dowel (CC) into each of the
pre-drilled holes. Attach to Hearth/Base (A) using
Bolts (AA) and Washers (BB) through the
pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.
2. Locate Left Side Panel (E) and Right Side Panel (F),
insert one Wood Dowel (CC) into each of the
pre-drilled holes. Attach to the completed front panel
assembly and Hearth/Base use Bolts (AA) and
Washers (BB) through the pre-drilled holes in the
mounting blocks.
HAND TIGHTEN ONLY.
5
Hardware Used
BB
AA
CC
Bolt x 2
Washer
x 2
Wood Dowel
x 4
3. Locate the Center Front Panel (D), insert one Wood
Dowel (CC) into each of the pre-drilled holes.
Push the Center Panel snug to the Right Front
Panel and Left Front Panel. Make sure the Wood
Dowels are seated in the pre-drilled holes.
Insert Bolts (AA) and Washers (BB) into the holes in
the mounting blocks.
HAND TIGHTEN ONLY.
Fig. 4
Fig. 3
Fig. 5
Hardware Used
BB
AA
CC
Bolt x 7
Washer x 7
Wood Dowel
x 6
4. Insert one Wood Dowel (CC) into each of the
pre-drilled holes on the top edges of the Assembly
from step 3. Then locate Mantel/Top (G) and lay
fi nished side up on top of completed assembly.
From the inside, attach Mantel/Top (G) using Bolts
(AA) and Washers (BB) through the pre-drilled
holes in the mounting blocks.
HAND TIGHTEN ONLY.
Using Phillips head screwdriver tighten all Bolts
alternating top and bottom, left and right.
CC
AA
BB
D
BB
AA
CC
G
Completed
Unit
Electric
Fireplace Insert
Install
Insert
From
Back
5. Remove the two mounting brackets attached to the
back of the Left and Right Front panels. Set aside
with the wood screws.
PLEASE READ ALL “ELECTRIC FIREPLACE
INSERT” INSTRUCTIONS PRIOR TO INSTALLING
ELECTRIC INSERT IN YOUR COMPLETED
FIREPLACE MANTEL. INSTALL THE INSERT IN
YOUR FIREPLACE
Lift insert carefully into the back of the unit and
center in the insert opening. Do not drag insert
across Hearth/Base (A) as it may scratch your unit.
Install the mounting brackets to hold insert fl ush
against the inside of the mantel front panel.
MOVE YOUR COMPLETED UNIT ONLY SHORT
DISTANCES. MOVE COMPLETED UNIT WITH
GREAT CARE. IT TAKES TWO PEOPLE TO
MOVE COMPLETED UNIT INTO ITS FINAL
POSITION.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Classic Flame 73238 Manuel utilisateur

Classic Flame
Marque
Classic Flame
Modèle
73238
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents