Allen-Bradley 140G-H Guide d'installation

Taper
Guide d'installation
Communication module for 140G-H, 140G-J
Modulo di comunicazione
Bul. 140G/140MG
DIR 1000721R0609 Version 01
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).
Installation - Installazione - Instalación
Instalação - -
DIR 1000721R0609 Version 01 - 140G-H-CIM
140G-H
140G-J
CLACK
140G-H
140G-J
x1
x1
x1
x1
x1
x1
x1
x1
警告:感事故止のため取付または修の際は電からり外して
ださい。切なース内に付けくださいまた、汚物質ないこと
確認してください。(NFPA70Eの要件に従ってください)
警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。符合NFPA70E要求)
1
Cable retainer
Com
module
Cables
2 3
1
1
2
(2)
1
2
2
3
3
140G-H, 140G-J
5
5
6
CLICK
4
DIR 1000721R0609 Version 01
1
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
140G-H
140G-H
140G-J
140G-H
5
6
8
4
7
9
140G-H
140G-H 140G-J
(3)
DIR 1000721R0609 Version 01
12
13
140G-J
140G-J 140G-J
(4)
10 11
Remove the plugs
DIR 1000721R0609 Version 01
(5)
14
2
2
1
15
16 17
DIR 1000721R0609 Version 01
(*) Supplied with the MCCB
3
Optional (*)
18 140G-H, 140G-J
6
6
5
5
1.1 Nm
9.7 lb-in
3
3
2
CLICK
4
(6)
DIR 1000721R0609 Version 01
1
Shielded
twisted pair wires
19
DIR 1000721R0609 Version 01 (L9011) - B0613
Copyright © 2016 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN104B-MU-P - February 2016
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/
sustainability-ethics/product-environmental-compliance.page
TO XH1 CONNECTION
ON ELECTRONIC
TRIP UNIT
CUSTOMER
CONNECTION
COMMUNICATION
MODULE
H & J FRAME
140G - H - CIM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Allen-Bradley 140G-H Guide d'installation

Taper
Guide d'installation