Maytag MES5552BA - 30 in. Electric Slide-In Range Mode d'emploi

Marque: Maytag

Modèle: MES5552BA - 30 in. Electric Slide-In Range

Taper: Mode d'emploi

YrAG

Electric Siide-|n Coil -

Precision Touch Control 500

Suaa_ecooking

Surface Controls

Coil Elements

Oven Cooking ......................... 6-13

Baking

Cook & Hold

Delay Cook & Hold

Keep Warm

Broiling

Sabbath Mode

Oven Racks

Maintenance ......................... 18-19

Oven Window

Oven Light

Troubleshooting ................... 20-21

Warranty & Service .................... 23

Guide d'utilisation et

d'entretien ................................... 24

Guia de Uso y Cuidado ............. 48

Form No. A/01/08 Part No. 8113P767-60 @2006 Maytag Appliances Sales Co. Litho U.S.A.

technician. Do not attempt to adjust, repair, service, or

replace any part of your appliance unless it is specifically

recommended in this guide. All other servicing should be

referred to a qualified servicer.

Always disconnect power to appliance before servicing.

portantSafety

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution,

and care must be exercised when installing, maintaining,

or operating the appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qualified

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear

leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor

when properly engaged. You should check this anytime

the range has been moved.

To Prevent Fire or

Smoke Damage

Be sure all packing materials are removed from the

appliance before operating it.

Keep area around appliance clear and free from

combustible materials. Flammable materials should not

be stored in an oven.

Many plastics are vulnerable to heat. Keep plastics away

from parts of the appliance that may become warm or

hot.

To prevent grease fires, do not let cooking grease or other

flammable materials accumulate in or near the appliance.

In Case of Fire

Use dry chemical or foam-type extinguisher or baking

soda to smother fire or flame. Never use water on a

grease fire.

1. Turn off appliance to avoid spreading the flame.

2. NEVER pick up or move a flaming pan.

3. Smother fire or flame by closing the oven door.

Turn off ventilating hood to avoid spreading the flame.

Extinguish flame then turn onhood to remove smoke

and odor.

Child Safety

NEVER leave children alone or unsupervised near the

appliance when it is in use or isstill hot. Children should

never be allowed to sit or stand on any part of the

appliance as they could be injured or burned.

Children must be taught that the appliance and utensils in

it can be hot. Let hot utensils cool in a safe place, out of

reach of small children. Children should be taught that an

appliance is not a toy. Children should not be allowed to

play with controls or other parts of the appliance.

About Your Appliance

To prevent potential hazard to the user and damage to the

appliance, do not use appliance as a space heater to heat

or warm a room. Also, do not use the oven as a storage

area for food or cooking utensils.

Do not obstruct the flow of air by blocking the oven vent.

The oven vent is located at the rear of the cooking

surface.

DO NOT TOUCH HEATING ELEMENTS OR INTERIOR

SURFACES OF OVEN. Heating elements may be hot even

though they are dark in color. Interior surfaces of any oven

become hot enough to cause burns. During and after use,

do not touch, or let clothing or other flammable materials

contact heating elements or interior surfaces of oven until

they have had sufficient time to cool. Other surfaces of the

appliance may become hot enough to cause burns -

among these surfaces are: oven vent opening and surface

near this opening, oven door, window of oven door.

Do not touch a hot oven light bulb with a damp cloth as

the bulb could break. Should the bulb break, disconnect

power to the appliance before removing bulb to avoid

electrical shock.

NEVER use aluminum foil to cover an oven rack or oven

bottom. Misuse could result in risk of electric shock, fire, or

damage to the appliance. Use foil only as directed in this

guide.

Do not use the cooktop or ovens as a storage area for food

or cooking utensils.

Cooking Safety

Never heat an unopened food container in the oven.

Pressure build-up may cause container to burst resulting in

serious personal injury or damage to the appliance.

Use dry, sturdy potholders. Damp potholders may cause

burns from steam. Dish towels or other substitutes should

never be used as potholders because they can trail across

hot elements and ignite or get caught on appliance parts.

Wear proper apparel. Loose fitting or long hanging-sleeved

apparel should not be worn while cooking. Clothing may

ignite and cause burns if garment comes in contact with

heating elements.

Always place oven racks in the desired positions while oven

is cool. Slide oven rack out to add or remove food, using

dry, sturdy potholders. Always avoid reaching into the oven

to add or remove food. If a rack must be moved while hot,

use a dry potholder. Do not let potholder contact hot

element in oven.

Use racks only in the oven in which they were shipped/

purchased.

Use care when opening the oven door. Let hot air or steam

escape before removing or replacing food.

PREPARED FOOD WARNING: Follow food manufacturer's

instructions. If a plastic frozen food container and/or its

cover distorts, warps, or is otherwise damaged during

cooking, immediately discard the food and its container.

The food could be contaminated.

Do not allow aluminum foil or meat probe to contact

heating element.

Always turn off all controls when cooking is completed.

Utensil Safety

Follow the manufacturer's directions when using oven

cooking bags.

This appliance has been tested for safe performance using

conventional cookware. Do not use any devices or accesso-

ries that are not specifically recommended in this guide. Do

not use element covers, stove top grills or add-on oven

convection systems. The use of devices or accessories that

are not expressly recommended in this guide can create

importantSurety

serious safety hazards, result in performance problems,

and reduce the life of the components of the appliance.

If pan is smaller than element, a portion of the element will

be exposed to direct contact and could ignite clothing or

potholder.

Only certain types of glass, glass/ceramic, ceramic, earth-

enware, or other glazed utensils are suitable for cooktop or

oven service without breaking due to the sudden change in

temperature. Follow utensil manufacturer's instructions

when using glass.

Turn pan handle toward center of cooktop, not out into the

room or over another surface element. This reduces the

risk of burns, ignition of flammable materials, or spillage if

pan is accidently bumped or reached by small children.

Cleaning Safety

Clean cooktop with caution. Turn off all controls and wait

for appliance parts to cool before touching or cleaning.

Clean with caution. Use care to avoid steam burns if a wet

sponge or cloth is used to wipe spills on a hot surface.

Some cleaners can produce noxious fumes if applied to a

hot surface.

Clean only parts listed in this guide.

Self-Clean Oven

Cooktop

NEVER leave surface units unattended especially when

using high heat. An unattended boilover could cause

smoking and a greasy spillover can cause a fire.

This appliance is equipped with different size surface

elements. Select pans with flat bottoms large enough to

cover element. Fitting pan size to element will improve

cooking efficiency.

Coil Elements

To prevent damage to removable heating elements, do

not immerse, soak or clean in a dishwasher or self-clean

oven. A damaged element could short resulting in a fire

or shock hazard.

Make sure drip bowls are in place as absence of these

bowls during cooking could damage wiring.

Protective Liners: Do not use aluminum foil to line

surface unit drip bowls or oven bottoms, except as

suggested in the manual. Improper installation of these

liners may result in a risk of electric shock or fire.

Deep Fat Fryers

Do not clean door gasket. The door gasket isessential for a

good seal. Care should be taken not to rub, damage, or

move the gasket.

Do not use oven cleaners or oven liners of any kind in or

around any part of the self-clean oven.

important Safety Notice

and Warning

The California Safe Drinking Water and Toxic Enforcement

Act of 1986 (Proposition 65) requires the Governor of

California to publish a list of substances known to the State

of California to cause cancer or reproductive harm, and

requires businesses to warn customers of potential expo-

sures to such substances.

Users of this appliance are hereby warned that when the

oven is engaged in the self-clean cycle, there may be some

low-level exposure to some of the listed substances, includ-

ing carbon monoxide. Exposure to these substances can be

minimized by properly venting the oven to the outdoors by

opening the windows and/or door in the room where the

appliance is located during the self-clean cycle.

Use extreme caution when moving the grease pan or

disposing of hot grease. Allow grease to cool before

attempting to move pan.

Ventilating Hoods

Clean range hood and filters frequently to prevent grease

or other flammable materials from accumulating on hood

or filter and to avoid grease fires.

IMPORTANT NOTICE REGARDING PET BIRDS: Never

keep pet birds in the kitchen or in rooms where the fumes

from the kitchen could reach. Birds have a very sensitive

respiratory system. Fumes released during an oven self-

cleaning cycle may be harmful or fatal to birds. Fumes

released due to overheated cooking oil, fat, margarine and

overheated non-stick cookware may be equally harmful.

When flaming foods under the hood, turn the fan on.

Save These Instructions for Future Reference

:Surfece. g

Surface Controls

Use to turn on the surface elements. An infinitechoice of

heat settings isavailable from Low to High. The knobs can

be set on or between any of the settings.

Setting the Controls

1. Place pan on surface element.

2. Push in and turn the knob in either direction to the desired

heat setting.

. The control panel is marked to identify O O

which element the knob controls. For Front • O

example, the graphic at right

indicates left front element.

There isan element indicator light on the control panel.

When any surface control knob isturned on, the light will

turn on.The light will turn offwhen all the surface ele-

ments are turned off.

4. Aftercooking, turn knob to OFF. Remove pan.

Suggested Heat Settings

The size and type of cookware, type and amount of food

being heated, and wattage of individual elements will

determine where to set the knob for cooking

operations. Some elements have a predetermined simmer and

melt setting that will require only minor adjustment up or

down depending on the food being prepared. The other

elements have settings printed around the knobs that are also

unique to those elements. Adjust the heat settings to the

numbers that give the desired cooking results. The following

descriptions will aid in choosing the settings that will give

optimum results.

Hold or Warm: Food maintains atemperature above 140°F

without continuing to cook. Food is initially hot and then heat

is reduced. Never use a hold or warm setting to reheat cold

food.

Simmer: Foodforms bubbles that barely break the

surface. Foods are between 185°Fand 200°F.A simmer

setting can also be used to steam or poach foods or continue

cooking covered foods.

Slow Boil: Food forms bubbles at a moderate pace. A slow

boil setting can also be used for most frying and for maintain-

ing the cooking of large amounts of liquids.

Boil: Liquid forms bubbles at a rapid pace. A fast boil setting

can also be used to brown meat, stir fry, saute, and heat oil

for frying before turning to a lower setting. The highest 3 or 4

settings on the knob are used for these cooking

operations. The highest setting is always used to bring water

to a boil. Some elements offer an even higher speed for

boiling liquids.

Surfece¢ookin9

Coil Element Surface

Notes:

, Clean cooktop after each use.

Wipe acidic or sugary spills as soon as the cooktop

has cooled as these spills may discolor or etch the

porcelain.

To protect drip bowl finish:

* To lessen discoloration and crazing, avoid using high

heat for long periods.

Do not use oversized cookware. Pans should not

extend more than 1-2 inches beyond the element.

When home canning or cooking with big pots, use

the Canning Element (Model CE1).Contact your

Maytag dealer for details or call 1-877-232-6771 USA

or 1-800-688-8408 Canada to order.

Clean frequently. (:Seepage 160

Coil Elements

, When an element is on, it will cycle on and off to maintain

the heat setting.

Coil elements are self-cleaning. Do not immerse in water.

To remove: When cool, raise

element. Carefully pull out and

away from receptacle.

To replace: Insert element

terminals into receptacle. Guide

the element into place. Press

down on the outer edge of

element until it sits level on drip

bowl.

TERMINALS

Drip Bowls

The drip bowls under each surface element catch boilovers

and must always be used. Absence of drip bowls during

cooking may damage wiring.

To prevent the risk of electric shock or fire, never line drip

bowls with aluminum foil.

Drip bowls will discolor (blue/gold stains) or craze over time if

overheated. This discoloration or crazing is permanent. This

will not affect cooking performance.

Control Panel

A B C D

E F G H | J

The control panel isdesigned for easeinprogramming. The displaywindow on the control shows time of day,timer and ovenfunctions.

Control panel shown includesmodel specific features. (Styling mayvary depending on model._)

!!!Cli:ii:!;!i_i_ii;!;

iiD!i_il;!ii!i_ii!i!i

;iilJii_ii_ii_ii_ii_ii_iiii,i!i!_!i

Broil

Bake

More+ or

Less-

Timer

Cook & Hold

Clean

Delay

Clock

Keep Warm

CANCEL

Usefor broiling and top browning.

Use for baking and roasting.

Enters or changes time, oven

temperature. Sets HI or LO broil.

Sets Timer.

Bakes for a preset time, then holds food

warm for 1 hour.

Use to set self-clean cycle.

Programs the oven to start baking at

a later time.

Use to set time-of-day clock.

Useto keep cooked food warm inoven.

Cancels all operations except Timer

and Clock.

Using the Touchpads

* Press the desired pad.

Pressthe More+ or Less= padto enter time or temperature.

A beep will sound when any pad istouched.

A double beep will sound if a programming error occurs.

Note: Four seconds after pressing the More+ or Less=

pad, the time or temperature will automatically be entered.

If more than 30 seconds elapse between touching a

function pad and the More+ or Less= pad, the function

will be canceled and the display will return to the previous

display.

Clock

The clock can be set to display time in a 12-hour or 24-hour

format. The clock isset at the factory for the 12-hour format.

To change the clock to 24-hour format:

1. Press and hold the CANCEL and

Delay pads for three seconds.

Press the More+ or Less= pad to

select 12 or 24 hour.

Set the time of day following the

directions below.

To set the Clock:

1. Press the Clock pad.

, The colon flashes in the display.

2. Press the More+ or Less= pad to set the

time of day.

Colon continues flashing.

3. Press the Clock pad again or wait four

seconds. The colon stops flashing.

When electrical power issupplied or after a power

interruption,the last clock time before power was

interruptedwill flash.

To recall the time of day when another time function is

showing, press the Clock pad.

Clock time cannot be changed when the oven has been

programmed for Delay Cook or Clean, or Cook & Hold.

To cancel the Clock display:

If you do not want the time of day to display:

Press and hold the CANCEL and Clock

pads for three seconds. The time of day will

disappear from the display

When the clock display is canceled, press

the Clock pad to briefly display the time of

day.

To restore the Clock display:

Press and hold the CANCEL and Clock pads for three

seconds. The time of day will reappear in the display.

Timer

The timer can be set from one minute (0:01) up to 99 hours

and 59 minutes (99:59).

The timer can be used independently of any other oven

activity. It can also be set while another oven function is

operating.

The timer does not control the oven. It only controls a beeper.

To set the Timer:

1. Press the Timer pad.

0:00 lights in the display.

The colon flashes in the display.

2. Press the More+ or Less= pad until the

correct time appears in the display.

The colon will continue to flash.

3. PressTimer pad again or wait four seconds.

The colon continues flashing and the time begins

counting down.

The last minute of the timer countdown will be displayed

as seconds.

4. At the end of the set time, one long beep will sound.

To cancel the Timer:

1. Press and hold the Timer pad for three seconds.

2. Press the Timer pad and set the time to 0:00.

Locking the Control

The touchpad controls can be lockedfor safety, cleaning, or

to prevent unwanted use. They will not function when locked.

If the oven iscurrently in use, the controls cannot be locked.

The current time of day will remain in the display when the

controls are locked.

To lock:

Press and hold the CANCEL and Cook &

Hold pads for three seconds. (Pressthe

CANCEL pad first.)

To unlock:

Press and hold the CANCEL and Cook & Hold pads for three

seconds. (Press the CANCEL pad first.)

Fault Codes

BAKE or LOCK may flash rapidly in the display to alert you if

there is an error or a problem. If BAKE or LOCK flash in the

display, press CANCEL pad. If BAKE or LOCK continue to

flash, disconnect power to the appliance. Wait a few minutes,

and then reconnect power. If the flashing still continues,

disconnect power to the appliance and call an authorized

servicer.

Baking

To set Bake:

1. Press the Bake pad.

* BAKE will flash.

000 will light in the display.

2. Select the oven temperature. The oven

temperature can be set from 170° to 550°. Press

or press and hold the More+ or Less- pad.

350°will light when either pad isfirst pressed.

Press the More+ pad to increasethe temperature.

Press the Less- pad to decrease the temperature.

3. Press Bake pad again or wait four seconds.

BAKEwill stop flashing and light in the display.

7. When cooking is finished, press CANCEL.

8. Remove food from the oven.

100° or the actual oven temperature will display. The

temperature will rise in 5 degree increments until the

preset temperature is reached.

4. Allow the oven to preheat for 8-15 minutes.

When the set oven temperature is reached, one long

beep will sound.

To recall the set temperature during preheat, press the

Bake pad.

Place food in the oven.

Check cooking progress. Cook longer if needed.

Baking Notes:

* To change the oven temperature during cooking,

press the Bake pad, then the More+ or Less- pad until

the desired temperature is displayed.

* To change the oven temperature during preheat, press

the Bake pad twice, then pressthe More+ or Less= pad

until the desired temperature isdisplayed.

* ifyou forget to turn off the oven, it will automatically turn

off at the end of 12 hours, ifyou wish to deactivate this

feature, see page 12.

Baking Differences Between Your Old

and New Oven

It isnormal to notice some baking time differences between a

new ovenand an old one. See"Adjusting the OvenTemperature"

on page 12.

Cook & Hold

Cook & Hold allows you to bake for a preset amount of time,

followed by a one-hour Keep Warm cycle.

To set Cook & Hold:

1. Press the Cook & Hold pad.

BAKE and HOLD flash.

* 000 lights in the display.

2. Select the oven temperature. The oven

temperature can be set from 170° to 550°. Press /

or press and hold the More+ or Less= pad. "_._ jjj/

Pressthe More+ pad to increase the temperature.

Pressthe Less- pad to decrease the temperature.

3. Press Cook & Hold again ORwait four seconds.

HOLD flashes.

00:00 flashes in the display.

4. Enter the amount of time you want to bake by pressing the

More+ or Less- pad. Bake time can be set from ten

minutes (00:10} to 11 hours, 59 minutes (11:59}.

BAKE and HOLD light in the display.

The baking time will light in the display.

The baking time will start counting down.

When the cooking time has elapsed:

* Four beeps will sound.

* BAKEwill turn off.

* HOLD and WARM will light.

* 170°will display.

After one hour in HOLD WARM:

. "End" will display.

* The time of day reappears in the display.

To cancel Cook & Hold at any time:

Press the CANCEL pad. Remove food

from oven.

Delay Cook & Hold

When using Delay, the oven begins to cook later inthe day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time, then keeps food warm for up to one hour.

Delay time can be set from 10 minutes (00:10) to 11 hours, 59

minutes (11:59).

To set a Delayed Cook & Hold cycle:

1. Pressthe Delay pad.

* DELAY flashes.

* 00:00flashes in the display.

2. Pressthe More+ or Less= pad to set the

delay time.

While DELAY isstill flashing:

3. Pressthe Cook & Hold pad.

* 000 lights in the display.

* BAKE and HOLD flash.

4. Press More+ pad to set the baking temperature.

* 00:00and HOLD flash.

* BAKE stays lit.

5. Press More+ pad to set the baking time.

* The Delay time, DELAY, BAKE and HOLD light in

the display.

When the Delay time has expired:

* DELAY will turn off.

* Baking time is displayed.

* BAKE and HOLD are displayed.

To set a Delay when Cook & Hold has already

been programmed:

1. Pressthe Delay pad.

* DELAY flashes.

* 00:00 appears in the display.

2. Pressthe More+ or Less- pad to set the

delay time.

* After four seconds, DELAY will

stay lit to remind you that adelayed

cooking cycle has been set.

When the Delay time has expired and the

oven starts:

* The baking time will bedisplayed.

* DELAY will turn off.

* BAKE and HOLD will remain lit.

To cancel:

Press the CANCEL pad.

* All timed and untimed cooking functions will be

canceled.

* The time of day will reappear in the display.

Notes:

* Do not use delayed baking for itemsthat require a

preheated oven, such as cakes, cookies, and breads.

* Do not use delayed baking ifoven isalready hot.

Keep Warm

For safely keeping foods warm or for warming breads

and plates.

To set Keep Warm:

1. Pressthe Keep Warm pad.

. WARM flashes.

. OOOappears in the display.

2. Select the Keep Warm temperature. The

Keep Warm temperature can be set from 145°

to 190°. Press or press and hold the More+

or Less- pad.

.170 ° will light when either pad is first pressed.

Press the More+ pad to increase the temperature.

Press the Less= pad to decrease the temperature.

WARM and the temperature will be displayed while Keep

Warm isactive.

Keep Warm Notes:

Foroptimal food quality, ovencooked foods should be kept

warm for no longer than 1 to 2 hours.

. To keep foods from drying, cover loosely with foil or a lid.

, To warm dinner rolls:

- cover rolls loosely with foil and place in oven.

- press Keep Warm and More+ pads to set 170° F.

- warm for 12-15 minutes.

To warm plates:

- place 2 stacks of up to four plates each inthe oven.

- press Keep Warm and More+ pads to set 170° F.

- warm for five minutes, turn off the oven and leave plates

in the oven for 15 minutes more.

- use only oven-safe plates, check with the manufacturer.

- do not set warm dishes on a cold surface as rapid

temperature changes could cause crazing or breakage.

To cancel Keep Warm:

1. Press the CANCEL pad.

2. Remove food from the oven.

Changing Temp °F/°C

1. The factory default setting for temperature is Fahrenheit.

2. To change the setting, press and hold the Cancel and Bake

pads at the same time for three seconds.

3. A single beep will sound and the current setting will be

displayed (°F or °C). (if no change is made, the range will

return to the existing setting after 30 seconds.)

4. To change the setting, press the More+ or Less= pad. Press

again to return to existing setting. Wait five seconds and the

setting will be complete.

Broiling

To set Broil:

1. Press the Broil pad.

* BROIL flashes.

* SEtisdisplayed.

2. Press the More+ pad to set Hi Broil or press the Less=

pad to set LO Broil.

* Hi or LO will be displayed.

* Select HI broil (550° F) for normal broiling. Select

LO broil (450° F)for low-temperature broiling of longer

cooking foods such as poultry.

3. After four seconds, the oven will start.

* BROIL will remain lit.

For optimum browning, preheat broil element for 3-4

minutes before adding food.

Place food in the oven. Leave oven door open about four

inches (the first stop).

Turn meat once about halfway through cooking.

When food is cooked, press the CANCEL

pad. Remove food and broiler pan from

the oven.

* The time of day will reappear in the display.

Broil Notes:

For best results when broiling, use a pan designed for

broiling.

Expect broil times to increase and browning to be

slightly lighter if appliance is installed on a 208-volt

circuit.

HI isused for most broiling. Use LO broil when broiling

longer cooking foods. The lower temperature allows

food to cook to the well done stage without excessive

browning.

To change the oven temperature during broiling,

press the Broil pad and then press the More+ or Less=

pad to switch between LO and HI broil.

Broil times may be longer when the lower broiling

temperature is selected.

Most foods should be turned halfway through broiling

time.

Broiling Chart

Beef

Steak, 1" thick

Hamburgers, 3/4" thick

Pork

Bacon

Chops, 1"

Ham - precooked slice, 1/2" thick

Poultry

Chicken Pieces

Seafood

Fish Steaks, buttered, 1" thick

Fillet_

The top rack position is#5.

Medium

Well Done

Warm

15- 18 minutes

19 - 23 minutes

15- 18 minutes

6- 10 minutes

22 - 26 minutes

8- 12 minutes

LO Broil

3 or 4 Well Done 28 - 38 minutes

Flaky

Flak_

Note: This chart isa suggested guide. The times may vary with the food being cooked.

10 - 15 minutes

8- 12 minutes

Automatic Shut=Off/

Sabbath Mode

The oven will automatically turn off after 12 hours if you

accidentally leave it on. This safety feature can be turned off.

To cancel the 12-hour shut=off and run the

oven continuously for 72 hours:

1. Set the oven to bake (see page 8:).

2. Press and hold the Clock pad for five seconds.

SAb will be displayed and flash for five seconds.

SAb will then be displayed continuously until turned

off or until the 72-hour time limit is reached.

BAKEwill also be displayed if a bake cycle is in use

while the oven is in Sabbath Mode.

BAKE b the only function that operates during the

Sabbath Mode. A# other functions (Timer, Keep Warm,

Clean, etc.) are locked out during the Sabbath Mode.

To cancel Bake when in Sabbath Mode:

Press CANCEL.

BAKEwill turn off inthe display.

No beeps will sound,

To cancel the Sabbath Mode:

1. Press the Clock pad for five seconds.

2. After 72 hours, the Sabbath Mode will end.

SAb will flash for five seconds.

The time of day will return to the display.

Adjusting the Oven Temperature

Oven temperatures are carefully tested for accuracy at the

factory. It is normal to notice some baking or browning

differences between a new oven and an old one. As ranges

get older, the oven temperature can shift.

You may adjust the oven temperature if you think the oven is

not baking or browning correctly. To decide how much to

change the temperature, set the temperature 25° higher or

lower than your recipe recommends, then bake. The results

of the "test" should give you an idea of how much to adjust

the temperature.

To adjust the oven temperature:

1. Press Bake.

Enter 550° by pressing the More+ pad.

Press and hold the Bake pad for several

seconds or until 0° appears in the display.

If the oven temperature was previously adjusted, the

change will be displayed. For example, if the oven

temperature was reduced by 15 degrees the display will

show -15°.

4. Press the More+ or Less- pad to adjust the temperature.

Eachtime a pad is pressed, the temperature changes by 5

degrees. The oven temperature can be increased or

decreased by 5 to 35 degrees.

5. The time of day will automatically reappear in the display.

You do not need to readjust the oven temperature if there

is a power failure or interruption. Broiling, Keep Warm and

Cleaning temperatures cannot be adjusted.

Sabbath Mode Notes:

Sabbath Mode can beturned on at any time with or

without the oven on.

Sabbath Mode cannot be turned on if the touchpads are

locked out or when the door is locked.

If the oven is baking when Sabbath Mode is set, BAKE

will go out at the end of the baking cycle. There will be

no audible beeps.

If the oven light is desired while in Sabbath Mode, it

must be turned on before the Sabbath Mode is started.

When the Sabbath Mode is started, no preheat beep will

sound.

All prompts, messages and beeps are deactivated when

Sabbath Mode is active.

The automatic door lock does not operate during the

Sabbath Mode.

Pressing CANCEL will cancel a Bake cycle, however the

control will stay in the Sabbath Mode.

If power fails, the oven will power up in Sabbath Mode with

72 hours remaining and no cycle active.

Oven Fan

A cooling fan will automatically turn on during all broiling and

some baking operations. It is used to keep internal parts on

the control panel cool. The fan will automatically turn off

when parts have cooled. The fan may continue to operate

after the oven has been turned off. This is normal.

Oven Vent

When the oven is in usethe area near the vent may become

hot enough to cause burns. Never block the vent opening.

The oven vent is located at the rear of the cooking

surface.

OVEN VENT LOCATION

Do not place

plastics near the \

vent opening as

heat from the vent

could distort or

melt the plastic.

Oven Light

Press the Oven Light switch on the control panel to

turn the oven light on and off. The oven light is only

activated by this switch.

Oven

Light

Oven Bottom

Protect oven bottom against spillovers, especially acidic or

sugary spills, as they may discolor the porcelain enamel. Use

the correct pan size to avoid spillovers and boilovers. Be not

place utensils or aluminum foil directly on the oven

bottom.

Oven Racks

To remove:

1. Pull rack straight out until it

stops at the lock-stop position.

2. Lift up on the front of the rack

and pull out.

To replace:

1. Place rack on the rack supports in the oven

2. Tilt the front end up slightly. Slide rack back until it clears

the lock-stop position.

3. Lower front and slide back into the oven.

Never cover an entire rack with aluminum foil or place

foil on the oven bottom. Baking results will be affected

and damage may occur to the oven bottom.

Rack Positions

RACK 5: Used for toasting

bread or broiling thin, non-

fatty foods.

RACK 4: Used for most

broiling.

RACK 3: Used for most

baked goods on a cookie

sheet or jelly roll pan, layer

cakes, or frozen convenience foods and general single-rack

baking. Used to broil chicken and fish on Low.

RACK 2: Used for pound cakes, Bundt cakes, pies, casseroles

and roasting small cuts of meat.

RACK 1: Used for pound cakes, 9 x 13 cakes, pies and

roasting large cuts of meat and poultry.

MULTIPLE RACK COOKING:

Two rack: Use rack positions 2 and 5,or 1 and 4.

Note: Never place pans directly on the oven bottom.

Baking Layer Cakes on Two Racks

The oven has two racks. All racks are designed with a lock-

stop edge.

Cleanin

Self-Clean Oven

To set Self=Clean:

i ote: Oven temperature must be below 400° Fto program

a clean cycle.

1. Close the oven door.

2. Move door lock lever right to the locked position.

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior.

The oven should be cleaned regularly bywiping up spillovers

to prevent excessive smoke and flare-ups. Do not allow a

heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self=Cleaning

1. Turn off the oven light before cleaning. The light may burn

out during the clean cycle.

Remove all pans and oven racks from the oven. The oven

racks will discolor and may not slide easily after a self-

clean cycle ifthey are not removed.

Clean oven frame, door frame, area

outside of gasket, and around the

opening in the door gasket with a

nonabrasive cleaner such as Bon

Ami* or detergent and water. The

self-cleaning process does not

clean these areas. They should be

cleaned to prevent soil from baking on during the clean

cycle. (The gasket isthe seal around the oven door and

window).

4. To prevent damage, do not clean or rub the gasket around

the oven door. The gasket isdesigned to seal in heat

during the clean cycle.

5. Wipe up excess grease or spillovers from the oven bottom.

This prevents excessive smoking, flare-ups or flaming

during the clean cycle.

Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

isacid-resistant, not acid-proof. The porcelain finish may

discolor if acidic spills are not wiped up before a self-clean

cycle.

3. Pressthe Clean pad.

, CLEAN flashes in the display.

4. Pressthe More+ or Less= pad.

, CL-M (Medium Soil, 3 hours) isdisplayed.

If the door isnot closed, beeps will sound and "door" will

display. If the door isnot closed within 45 seconds, the

self-cleaning operation will be canceled and the display

will return to the time of day.

S j,,,,, ..................

5. Pressthe More+ or Less= pad to scroll through ( More+ )

the self-cleaning settings. '"........................J

CL-H (HeavySoil, 4 hours)

CL-M (Medium soil, 3 hours)

CL-L (Light Soil, 2 hours)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, the oven will start cleaning.

, The cleaning time will start counting down in the display.

, LOCK will appear in the display.

, CLEAN will appear in the display.

To Delay a Self=Clean Cycle:

1. Pressthe Delay pad.

, DELAY flashes.

, OO:OOwill appear in the display.

2. Pressthe More+ or Less= pad to set the

amount of time you want to delay the cycle.

Delay time can be set from ten minutes

(00:10) to 11 hours, 59 minutes (11:59).

3. While DELAY isflashing, press the

Clean pad.

, CLEAN will flash.

4. Pressthe More+ or Less= pad.

, CL-M (Medium Soil, 3 hours) isdisplayed.

cont.

*Brand names for cleaning products are registered trademarks ofthe respective manufacturers.

5. Press the More+ or Less= pad to scroll through the

self-cleaning settings.

CUH (HeavySoil, 4 hours)

CL-M (Medium soil, 3 hours)

CL-L (Light Soil, 2 hours)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, CLEAN, DELAY and LOCKwill appear

in the display to show that the oven isset for a delayed

clean operation. The delay time isdisplayed.

During the Self=Clean Cycle

When LOCK shows in the display, the door cannot be opened.

To prevent damage to the door, do not force the door open

when LOCK is displayed.

Smoke and Smells

You may see some smoke and smell an odor the first few

times the oven is cleaned. This is normal and will lessen in

time.

Smoke may also occur if the oven is heavily soiled or if a

broiler pan was left in the oven.

Sounds

As the oven heats, you may hear sounds of metal parts

expanding and contracting. This is normal and will not

damage the oven.

|fthe oven has already been setfor a clean

cycle and you wishto seta delay:

1. Press the Belay pad.

DELAYflashes.

00:00 will appear in the display.

2. Press the More+ or Less= pad to set the

amount of time you want to delay the cycle.

After four seconds, CLEAN, DELAY and LOCK ....................................

will appear in the display to show that the t Less- )

oven is set for a delayed clean operation. The

delay time is displayed.

When the Self=Clean cycle starts:

DELAYwill turn off.

The clean time will appear in the display.

To cancel the Self=Clean cycle:

Press the CANCEL pad.

All words disappear from the display.

All functions are canceled.

The time of day appears in the display.

After Self=Cleaning

About one hour after the end of the self-clean cycle, LOCK

will turn off. The door can then be opened. Move door lock

lever to the left to unlock.

Some soil may leave a light gray, powdery ash. Remove

itwith a damp cloth. If soil remains after wiping, that means

the clean cycle was not long enough. The soil will be

removed during the next clean cycle.

If oven racks were left in the oven and do not slide

smoothly after a clean cycle, wipe racks and rack supports

with a small amount of vegetable oil to make them easier to

move.

Fine lines may appear in the porcelain because it went

through heating and cooling. This isnormal and will not

affect performance.

A white discoloration may appear after cleaning if acidic

or sugary foods were not wiped up before the self=clean

cycle. This discoloration is normal and will not affect

performance.

Notes:

If the oven door is left open, "door" will flash in the

display and a signal will beep until the door is closed

and the Clean pad is pressed again.

If more than five seconds elapse between pressing the

Clean pad and the More+ or Less- pad, the program

will automatically return to the previous display.

The oven door will be damaged if the oven door is

forced to open when LOCK is still displayed.

Cleaning Procedures

* Brand names are registered trademarks of the

respective manufacturers.

** To order call 1-877-232-6771 USA or

1-800-688-8408 Canada.

Cooktop -

Porcelain Enamel

Clock and

Control Pad

Area

Control Knobs

Drip Bowls =

Porcelain

Oven Window

and Door = Glass

Oven Interior

Porcelain enamel is glass fused on metal and may crack or chip with misuse. It isacid resistant, not acid

proof. All spillovers, especially acidic or sugary spillovers, should bewiped up immediately with a dry cloth.

. When cool, wash with soapy water, rinse and dry.

. Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping.

. Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.

. To activate control lock for cleaning, see "Locking the Controls" page 7.

. Wipe with a damp cloth and dry. Do not use abrasive cleaning agents as they may scratch the finish.

', Glass cleaners may be used if sprayed on a cloth first. DO NOT spray directly on controlpadand

display area.

. Remove knobs in the OFF position by pulling forward.

. Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.

. Turn on each element to be sure the knobs have been correctly replaced.

Porcelain may discolor or craze if overheated. This is normal and will not affect cooking performance.

. When cool, wash after each use, rinse and dryto prevent staining or discoloration. May bewashed in the

dishwasher.

. To clean heavy soil, soak in hot sudsy water, then use amild abrasive cleaner such as Soft Scrub* and a

plastic scouring pad.

. For burned on soil, remove from range, place on newspapers and carefully spraywith commercial oven

cleaner. (Do not spray surrounding surfaces.) Placein plastic bag and allowto soakseveralhours.Wearing

rubber gloves, remove from bag, wash, rinse and dry.

. Avoid using excessive amounts of water which may seep under or behind glass causing staining.

. Wash with soap and water. Rinsewith clearwater anddry. Glasscleaner can be usedif sprayed on a cloth

first.

. Do not useabrasive materials such as scouring pads, steelwool or powdered cleaners asthey will scratch

glass.

', Follow instructionson page 14-15 to set a self-clean cycle.

Cleanln l

Oven Racks

Stainless Steel

(select models)

Storage Drawer,

Door Handle =

Painted Enamel

Clean with soapy water.

Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.

Rackswill permanently discolor and may not slidesmoothly ifleft inthe ovenduring a self-clean operation.

If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to restore ease

of movement, then wipe off excess oil.

* DO NOT USEANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.

* DO NOT USEABRASIVE OR ORANGE CLEANERS.

* ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.

', Daily Cleaning/Light Soil ==Wipe with one ofthe following -soapywater, white vinegar/water solution,

Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse

and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray* (Part No.

20000008)**.

* Moderate/Heavy Soil == Wipe with one of the following -Bon AmP, Smart Cleanser*, or Soft Scrub* -

using a damp sponge or soft cloth. Rinseand dry.Stubborn soils may be removed with a damp multi-

purpose Scotch-Brite* pad; rub evenly with the grain. Rinse and dry.To restore luster and remove streaks,

follow with Stainless Steel Magic Spray*.

* Discoloration == Using a damp sponge or soft cloth, wipe with CameoStainless Steel Cleaner*. Rinse

immediatelyand dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.

When cool, wash with warm soapy water, rinse and dry.Never wipe a warm or hot surface with a damp

cloth as this may damage the surface and may cause a steam burn.

Forstubborn soil, use mildly abrasive cleaning agents such as baking soda paste or Bon Ami.* Do not use

abrasive, caustic or harsh cleaning agents such assteel wool pads or oven cleaners. These products will

scratch or permanently damage the surface.

Note: Use a dry towel or cloth to wipe up spills, especially acidic or sugary spills. Surface may

discolor or dull ifsoil isnot immediately removed. Thisis especially important forwhite surfaces.

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

** To order direct, call 1-877-232-6771 USA or 1-800-688-8408 Canada.

eintenence

Oven Door

Note: The oven door on a new range may feel "spongy" ]

when it is closed. This is normal and will decrease with use.

To remove:

1. When cool, open the oven door to the first stop

(opened about four inches).

2. Grasp door at each side. Do not use the

door handle to lift door.

3. Lift up evenly until door clears hinge

arms.

To replace:

1. Grasp door at each side.

position

Align slots in the door with the hinge arms on the range.

Slide the door down onto the hinge arms until the door is

completely seated on the hinges. Push down on the top

corners of the door to completely seat door on hinges. Door

should not appear crooked.

Oven Window

To protect the oven door window:

1. Do not use abrasive cleaning agents such as steel wool

scouring pads or powdered cleansers as they may scratch

the glass.

2. Do not hit the glass with pots, pans, furniture, toys, or other

objects.

3. Do not close the oven door until the oven racks are in

place.

Scratching, hitting, jarring or stressing the glass may weaken

its structure causing an increased risk of breakage at a later

date.

Leveling Legs

Be sure the range is leveled when installed. If

the range is not level, turn the leveling legs,

located at each corner of the range, until

range is level.

ANTI-TIP BRACKET

LEVELING LEG

Oven Light (style varies by model:)

Storage Drawer

To replace oven light bulb:

1. When oven iscool, hold bulb cover

in place, then slidewire retainer

off cover. Note: Bulb cover

will fall if not held in place

while removing wire retainer.

2. Remove bulb cover and light

bulb.

BULB COVER

RETAINER

3. Replace with a 40-watt appliance bulb.

4. Replace bulb cover and secure with wire retainer.

5. Reconnect power to range. Reset clock.

1. Use a dry potholder and very carefully unscrew bulb cover

and bulb.

2. Replace with a 40 watt, oven-rated appliance bulb. Bulb

with a brass base is recommended to prevent fusing of

bulb into socket.

3. Replace bulb cover and reconnect power to oven.

4. Resetclock.

The storage drawer can be removed to allow you to clean under

the range.

To remove:

1. Empty drawer and pull out to the first stop position.

2. Lift up the front of the drawer.

3. Pull out to the second stop position.

4. Grasp sides and lift drawer top up and out.

To replace:

1. Fit the ends of the drawer glides into the rails in the range.

2. Lift up the front of the drawer and gently push in to the first

stop position.

3. Lift drawer up again and push until drawer is closed.

La page charge ...

Maytag MES5552BA - 30 in. Electric Slide-In Range Mode d'emploi

Marque: Maytag

Modèle: MES5552BA - 30 in. Electric Slide-In Range

Taper: Mode d'emploi

Télécharger le PDF

rapport

Maytag MES5552BA - 30 in. Electric Slide-In Range Mode d'emploi

Maytag MES5552BA - 30 in. Electric Slide-In Range Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents