Simplicity 2691481-00 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
Not for
Reproduction
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
80078390
Revision A
Not for
Reproduction
2
1
2
3
4
5
6
7
Not for
Reproduction
3
8
9
10
11
12
13
14
15
Not for
Reproduction
4
Table of Contents:
Products Covered by This Manual......................................5
General Information..............................................................5
European Office Contact Information.................................5
European Union (EU) Stage V (5): Carbon Dioxide (CO2)
Values.....................................................................................5
Operator Safety..................................................................... 5
Slope Identification Guide................................................ 5
Safety Symbols and Meanings.........................................5
Safety Alert Symbol and Signal Words............................ 6
Safety Decals................................................................... 6
Safety Messages.............................................................7
Features and Controls..........................................................7
Control Symbols and Meaning.........................................7
Operation............................................................................... 9
Operating Area................................................................. 9
Safety Interlock System Tests..........................................9
Electronic Dash Panel....................................................10
Engine.............................................................................10
Tractor Operation........................................................... 12
Mowing............................................................................13
Adjust Mower Cutting Height..........................................13
Reverse Mowing Option (RMO)..................................... 13
Maintenance.........................................................................14
Maintenance Schedule................................................... 14
Tire Pressure Check...................................................... 14
Battery Maintenance.......................................................14
Mower Blade Stop Time.................................................15
Change the Engine Oil...................................................15
Air Filter Assembly (Cartridge with pre-cleaner).............15
Check the Spark Plugs.................................................. 15
Pushing the Tractor by Hand......................................... 15
Towed Equipment...........................................................16
Clean the Mower Deck (if equipped)..............................16
Storage.................................................................................16
Troubleshooting..................................................................17
Troubleshooting the Rider..............................................17
Troubleshooting the Mower............................................17
Specifications......................................................................18
Specifications Chart........................................................18
Not for
Reproduction
5
Products Covered by This
Manual
The following products are covered by this manual:
2691481-00, 2691481-01,2691481-02,2691482-00,
2691483-00, 2691487-00, 2691487-01,2691487-02,
2691488-00, 2691489-00, 2691576-00.
General Information
For additional information, refer to the Customer Contact
Guide included with the unit.
The illustrations in this document are representative. Your
unit might look different from the images shown. LEFT and
RIGHT are referenced from the operating position.
The use of Important and Note in the text shows clarifications,
exceptions, or alternatives to the procedures.
All language translations of this document derive from the
initial English source file.
Recycle all packaging, used oil, and batteries according to
applicable government regulations.
European Office Contact
Information
For questions regarding European emissions, please contact
our European office at:
Max-Born-Straße 2, 68519 Viernheim, Germany.
European Union (EU) Stage
V (5): Carbon Dioxide (CO
2
)
Values
Carbon dioxide values of Briggs & Stratton EU Type-Approval
Certificate engines can be found by entering CO2 into the
search window on BriggsandStratton.com.
Operator Safety
Save these instructions for future reference.This manual
contains safety information to make you aware of the hazards
and risks associated with the product and how to avoid them.
It also contains important instructions that must be followed
during the initial set-up, operation, and maintenance of the
product.
This product is designed and intended for cutting well
maintained grass and is not intended for other purposes.
It is important that you read and understand these instructions
before you attempt to start or operate this equipment.
Make sure that you are fully familiar with the controls and the
correct use of the product.
Know how to stop the unit and disengage controls quickly.
Slope Identification Guide
How to measure the slope of a lawn surface with a
smartphone or an angle finder tool:
WARNING
Do not operate on slopes greater than10degrees.
1. Use a straight edge at least two (2) feet long (A,
Figure1). A 2x4 or a straight piece of metal works well.
2. Angle finder tools.
a. Use your smartphone:Many smartphones (B,
Figure1) have an inclinometer (angle finder) located
under the compass application (app). Or, search an
app store for an Inclinometer app.
b. Use angle finder tools:Angle finder tools (C and
D, Figure1) are available at local hardware stores
or online (also called inclinometer, protractor, angle
meter, or angle gauge). Dial type (C) or digital type
(D) work, others may not. Follow user instructions
with the angle finder tool.
3. Put the two (2) feet long straight edge along the steepest
part of the lawn slope. Put the board up and down the
slope.
4. Lay the smartphone or angle finder tool on the straight
edge and read the angle in degrees. This is the slope of
your lawn.
Note:A paper gauge slope identification guide is included
in your product literature packet and is also available to
download from the manufacturer's website.
Safety Symbols and Meanings
Symbol Meaning
Safety information about hazards that can result in personal
injury.
Read and understand the Operator's Manual before you
operate or service the unit.
Remove the key and read the Operator's Manual before
you service the unit.
Not for
Reproduction
6
Symbol Meaning
Stop
Fire hazard
Explosion hazard
Shock hazard
Toxic fume hazard
Moving parts
Wear eye protection.
Hazardous chemical
Hot surface hazard
Amputation hazard
Thrown objects hazard
Symbol Meaning
Keep a safe distance
Keep children away
Roll-over hazard
Amputation hazard
Safety Alert Symbol and Signal Words
The safety alert symbol identifies safety information
about hazards that can result in personal injury. A signal word
(DANGER, WARNING, or CAUTION) is used with the alert
symbol to indicate the likelihood and the potential severity of
injury. In addition, a hazard symbol may be used to represent
the type of hazard.
DANGER indicates a hazard which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE indicates an action that could result in damage to
the product.
Safety Decals
Before you operate the machine, read the safety decals.
Compare Figure2to the decals shown in the table below.
The cautions and warnings are for your safety. To avoid
personal injury or damage to the machine, understand and
follow all the safety decals.
 
Important:If any safety decals become worn or damaged,
and cannot be read, order replacement decals from your local
dealer.
Not for
Reproduction
7
A
B
Safety Decal Icon Definitions
Compare the letters (A - J) in the safety decal icons to
thesafety definitions listed in the table that follows.
A WARNING:Read and understand the Operator's Manual before
you use this machine. Know the location and function of all controls.
Do not operate this machine unless you are trained.
B DANGER - LOSS OF TRACTION, SLIDING, STEERING
AND CONTROL ON SLOPES HAZARD:If the machine stops
forward motion or starts to move on a slope, stop the blades,
andslowlydriveoff the slope.
C DANGER - FIRE HAZARD:Make sure the unit is free of grass,
leaves, and excess oil. Do not add fuel while the engine is hot or on.
Stop the engine. Let the engine cool for at least 3 minutes before
you add fuel. Do not add fuel indoors, in an enclosed trailer, garage
or other enclosed areas. Remove spilled fuel. Do not smoke while
you operate this machine.
D DANGER - TIPPING AND SLIPPING HAZARD:Mow up and down
slopes not across. Do not operate on slopes more than 10 degrees.
Avoid sudden and sharp (fast) turns while on slopes.
E DANGER - AMPUTATION AND DISMEMBERMENT HAZARD:To
avoid injury from rotating blades and moving parts, keep safety
devices (guards, shields and switches) in place and working.
F Do not mow when children or others are around. DO NOT carry
riders especially children even with the blades off. Do not mow
in reverse unless absolutely necessary. Look down and behind –
before and while you drive the unit in reverse.
G Consult technical literature before technical repairs or maintenance.
When you leave the machine, stop the engine, set the parking
brake to the lock position, and remove the ignition key.
H Keep by-standers and children a safe distance away. Remove
objects that can be thrown by the blade. Do not mow without the
discharge chute in place.
I Do not mow without discharge chute or entire grass catcher in
place.
J To avoid injury from rotating blades, stay clear of deck edge and
keep others away.
Safety Messages
WARNING
Read, understand, and follow all the instructions and
warnings in the Operator's Manual and on the machine,
engine, and attachments before you operate this machine.
Failure to observe the safety instructions in this manual and
on the equipment could result in death or serious injury.
Only let operators who are responsible, trained and
familiar with the instructions and physically capable to
operate the machine.
Do not operate the machine while under the influence of
alcohol or drugs.
Wear safety glasses and closed toe footwear.
Do not put hands or feet near rotating parts or under
the machine. Keep clear of the discharge opening at all
times.
Keep the machine in good working order. Replace worn
or damaged parts.
Be careful when youservice the blades. Wrap the
blades or wear gloves. Replace damaged blades. Do
not repair or alterthe blades.
Use full width ramps when you load and unload a
machine for transport.
See attachment or accessory for proper wheel weights
or counterweights.
To help prevent fires, keep machine free of grass,
leaves, or other unwanted material. Clean remaining oil
or fuel spillage. Remove fuel soaked debris and let the
machine to cool before storage.
WARNING
Running engine gives off carbon monoxide, an odorless,
colorless, poison gas. Breathing carbon monoxide can
cause headaches, fatigue, dizziness, vomiting, confusion,
seizures, nausea, fainting or death.
Operate equipment ONLY outdoors.
Keep exhaust gas from entering a confined area
through windows, doors, ventilation intakes, or other
openings.
Features and Controls
Compare Figure3with the table that follows.
Features and controls may differ from those shown.
Control Symbols and Meaning
A Reverse Mowing Option
Not for
Reproduction
8
B Hourmeter (if equipped)
Ignition Switch
OFF
RUN
Start
C
Headlight Switch
D Power Take-Off(PTO) Switch Up,
Engage Blades
E Power Take-Off
F Power Take-Off (PTO) Switch Down,
Disengage Blades
G Cruise Control
H Parking Brake Control
I Throttle Control
J Throttle Control SLOW Position
K Throttle Control FAST Position
L Choke
M Ground Speed Pedals
N Mower Lift Lever
O Transmission Release Lever
P Fuel Tank
Q Fuel Level Gauge
R Brake Pedal
S Seat Adjustment Lever
Not for
Reproduction
9
T Height-of-Cut Switch (if equipped)
Operation
Read theOperator Safetysection before you operate this
machine. Make sure that you know the controls and how to
stop the unit.
Operating Area
1. Know the area where you plan to operate the mower.
2. Make sure that the area is free of unwanted material that
could be picked up by the blades and thrown.
DANGER
This machine is capable of throwing objects that could
injure bystanders or cause damage to buildings.
Do not operate the machine without the entire grass
catcher, discharge chute, or other safety devices in
place and functioning properly. Check frequently for
signs of wear or detoriation and replace as needed.
Clear the operating area of any objects which could
be thrown by or interfere with the operation of the
machine.
3. Move the rider mower outside, before you start the
engine.
WARNING
Engines give off carbon monoxide, an odorless, colorless,
poison gas. Breathing carbon monoxide can cause nausea,
fainting, or death.
4. Note all slopes and drop-offs.
DANGER
Operating on slopes, or near water, or drop-offs can result
in loss of control and roll-over.
Mow up and down slopes not across.
Reduce speed and be careful on slopes.
Do not operate on slopes over 10 degrees, which is a
3.5 foot rise over a 20 foot length.
Give yourself a minimum of two mower widths of
clearance around water, retaining walls, or drop-offs.
Avoid mowing wet grass.
Do not operate machine under any condition where
traction, steering, or stability is in question. Tires could
slide even if the wheels are stopped.
Avoid starting and stopping on slopes.
Avoid making sudden changes in speed or direction.
Make turns slowly and gradually.
Be careful while operating machine with a grass catcher
or other attachment(s). They can affect the stability of
the machine.
Follow the manufacturer's recommendation for weight
limits for towed equipment and towing on slopes.
SeeTowed Equipment.
5. Make sure that the operating area is clear of bystanders,
especially children.
DANGER
This rider mower is capable of amputating hands and feet.
Stop the mower when children or others are near.
Keep children out of the operating area and under the
watchful care of a responsible adult.
Do not carry passengers, especially children, even
with the blade(s) shut off. Children can fall off and be
seriously injured or interfere with the safe machine
operation. Children who have been given rides in
the past can suddenly appear in the mowing area for
another ride and be run over or backed over by the
machine.
Use care when approaching blind corners, shrubs,
trees, or other objects that obscure vision.
Safety Interlock System Tests
This machine is equipped with a Safety Interlock System.
Do not attempt to bypass or tamper with the switches and
devices.
WARNING
If the machine does not pass a safety test, do not
operate the machine. See an authorized dealer.
Test 1 — Engine should NOT crank if
The Power-Take-Off (PTO) switch is ON, OR
Not for
Reproduction
10
The brake pedal is NOT fullydepressed(parking brake
OFF).
Test 2 — Engine SHOULD crank and start if
The PTO switch is OFF, AND
The Brake pedal is fullydepressed(parking brake ON).
Test 3 — Engine should SHUT OFF if
The operator rises off the seat with the PTO engaged.
The operator rises off the seat with the brake pedal NOT
fully depressed (parking brake OFF).
Test 4 — Mower Blade Stopping TimeCheck
The mower blades and mower drive belt should come to
a complete stop within five seconds after the PTO switch
is turned OFF.
If the drive belt does not stop within five seconds, see an
authorized dealer.
Test 5 — Reverse Mowing Option (RMO) Check
The engine should shut off if reverse travel is attempted
if the PTO has been switched ON and the RMO has not
been activated.
The RMO light should come on when the RMO has been
activated.
DANGER
Mowing in reverse can be hazardous to bystanders. Tragic
accidents can occur if the operator is not alert to the
presence of children. Never activate the Reverse Mowing
Option (RMO) if children are present. Children are often
attracted to the machine and the mowing activity.
Electronic Dash Panel
Display Total Hours, Trip Hours, and Clock
Note:When you start the unit, the Total Hours show on the
maintenance display. The total hours will set to 0 after 999.9.
1. Push MODE for less than 1 second to show the Trip
Hours.
2. Push RESET for more than 3 seconds to set the Trip
Hours to 0.
3. Push MODE for less than 1 second to show the Clock.
SeeSet the Clocksection.
4. Push MODE for less than 1 second to show the Total
Hours.
Set the Clock
1. Push MODE for more than 3 seconds. The hours will
flash on the display.
2. Push RESET to adjust the hours.
3. Push MODE for less than 1 second to save the setting.
The minutes will flash on the display.
4. Push RESET to adjust the minutes.
5. Push MODE for less than 1 second to save the setting.
Maintenance Display
OIL CHANGE- This message shows after 50 hours of
operation. After you change the oil and filter, push MODE two
times to show OIL HRS. Then, push and hold MODE for 3
seconds to set the timer to zero and clear the display.
AIR FILTER CHECK- This message shows after 25 hours of
operation. After you clean or change the air filter, push MODE
three times to show AIR FILTER HRS. Then, push and hold
MODE for 3 seconds to set the timer to zero and clear the
display.
CHANGE BLADES- This message shows after 100 hours
of operation. After you change the blade, hold the RESET
button for more than 3 seconds to set the timer to zero and
clear the display.
LOW BATTERY- This message shows when a battery
voltage problem occurs. The display will automatically clear
after the battery has been serviced.
Note:When the LOW BATTERY message shows on the
display, it has priority over all other messages. Service
the battery first, and then, check for other maintenance
messages.
Engine
Check and Add Engine Oil
Use Briggs & Stratton
®
Warranty Certified oils for best
performance. Other high-quality detergent oils are acceptable
if classified for service SF, SG, SH, SJ or higher. Do not use
special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
Not for
Reproduction
11
A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard
starting.
B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 can cause increased
oil consumption. Check oil level more frequently.
C 5W-30
D Synthetic 5W-30
E
Vanguard
®
Synthetic 15W-50
*Below 40°F (4°C) the use of SAE 30 will result in hard starting.
**Above 80°F (27°C) the use of 10W-30 can cause increased oil consumption.
Check oil level more frequently.
1. Put the unit on a level surface as shown in Figure4.
2. Stop the engine and remove the key.
3. Make sure that the oil fill area is clean.
4. Remove the dipstick(A, Figure5).Remove the remaining
oil from the dipstick.
5. Install and tighten the dipstick.
6. Remove the dipstick again,and check the oil level.Make
sure that the oil level is at the top of theFULL mark
(B)on the dipstick.
7. If the oil level is FULL, install and tighten the dipstick.
8. Ifthe oil level is LOW, add oil into the engine oil fill tube
(C). Do not overfill.
Note:Do not add oil at the quick oil drain (if equipped).
9. Wait one minute, and check the oil level again.
10. Replace and tighten the dipstick.
Oil Pressure
If the oil pressure is too low, a pressure switch (if equipped)
will either stop the engine or activate a warning device on the
equipment. If this occurs, stop the engine and check the oil
level with the dipstick.
If the oil level is below the ADD mark, add oil until it reaches
the FULL mark. Start the engine and check for the correct oil
pressure before you continue to operate the machine.
If the oil level is between the ADD and FULL marks,do not
start the engine. Contact an authorized dealer to have the oil
pressure problem corrected.
Add Fuel
Fuel must meet these requirements:
Clean, unleaded gasoline.
A minimum of 87 octane / 87 AKI (91 RON). SeeHigh
Altitude Requirements.
Gasoline with up to 10% ethanol (gasohol).
NOTICE Do not use unapproved gasolines, such as E15
and E85. Do not mix oil in gasoline or modify the engine to
run on alternate fuels. Use of unapproved fuels will cause
damage to engine components, which will not be covered
under warranty.
To protect the fuel system from gum formation, mix a fuel
stabilizer into the fuel.If start or performance problems occur,
change fuel providers or brands. This engine is certified to
operate on gasoline. The emissions control system for this
engine is EM (Engine Modifications).
High Altitude Requirements
At altitudes over 5,000 feet (1,524 meters), a minimum 85
octane / 85 AKI (89 RON) gasoline is acceptable.
For carbureted engines, high altitude adjustment is
required to remain emissions compliant. Operation
without this adjustment will cause decreased
performance, increased fuel consumption, and increased
emissions. Contact a Briggs & Stratton Authorized
Service Dealer for high altitude adjustment information.
Operation of the engine at altitudes below 2,500 feet
(762 meters) with the high altitude adjustment is not
recommended.
For Electronic Fuel Injection (EFI) engines, high altitude
adjustment is not necessary.
WARNING
Fuel and its vapors are extremely flammable and explosive.
Always handle fuel with extreme care. Failure to Observe
these safety instructions can cause fire or explosion which
could result in severe burns or death.
Turn the engine off and let the engine cool at least 3
minutes before you remove the fuel cap.
Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
Fill fuel tank outdoors or in well-ventilated area.
Do not overfill fuel tank. To allow for expansion of the
fuel, do not fill above the bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
Check fuel lines, tank, cap, and fittings frequently for
cracks or leaks. Replace if necessary.
If fuel spills, wait until it evaporates before starting
engine and avoid creating any source of ignition.
Use only an approved fuel container.
1. Remove unwanted material from the fuel cap area.
2. Remove the fuel cap (A,Figure6).
3. Fill the fuel tank (B)with fuel. DO NOT fill above the
bottom of the fuel tank neck (C).
4. Install the fuel cap.
Start the Engine
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Starting the Engine
Ensure that spark plug, muffler, fuel cap, and air
cleaner (if equipped) are in place and secured.
Do not crank engine with spark plug removed.
If engine floods, set choke (if equipped) to OPEN/RUN
position, move throttle (if equipped) to FAST position
and crank until engine starts.
Not for
Reproduction
12
WARNING
Engines give off carbon monoxide, an odorless, colorless,
poison gas.
Breathing carbon monoxide can cause nausea, fainting, or
death.
Fire or explosion can cause severe burns or death.
Start and run engine outdoors.
Do not start or run engine in enclosed area, even if
doors or windows are open.
1. Check the oil level. SeeCheck and Add Engine Oil.
2. Make sure that the equipment drive controls are
disengaged.
3. Sit in the seat and lift UP the seat adjustment lever to lock
the seat in position.
4. Engage the parking brake. Push the brake pedal, pull
UP on the parking brake control, and release the brake
pedal.
5. Disengage PTO switch by pushing IN.
6. Set the throttle/choke control to the CHOKE position (if
equipped).
7. Put the key into the ignition switch and turn it to the ON/
START position. For push-button start models, push the
button two times and hold until the engine starts.
8. After the engine starts, move the throttle/choke control to
half speed. Turn the engine ON for at least 30 seconds.
This will warm the engine. 
9. Set throttle/choke control to the FAST position.
In the event of an emergency, to stop the engine, turn the
ignition switch to the STOP position. For normal engine shut
down seeStop Tractor and Engine.
Note:If the engine does not start after repeated attempts,
contact an authorized dealer.
Stop Tractor and Engine
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Do not choke the carburetor to stop the engine.
1. Release the ground speed pedals (M,Figure3) to return
to the NEUTRAL position.
2. Disengage the PTO switch (D), then wait for all moving
parts to stop.
3. Move the throttle control (J)(or throttle/choke control) to
the SLOW position and turn the ignition key (C)to the
OFF position.
4. Remove the key.
5. Engage the parking brake control (H). Push the brake
pedal (R), pull UP on the parking brake control, and
release the brake pedal.
In the event of an emergency, turn the ignition switch to the
STOP position. This will stop the engine.
Tractor Operation
1. Sit in the seat and adjust the seat so that you can
comfortably reach all the controls. SeeFeatures and
Controls.
2. Engage the parking brake control (H, Figure1):
a. Fully push down on the brake pedal (P).
b. Pull UP on the parking brake.
c. Release the brake pedal.
3. Make sure the PTO switch (O) is disengaged.
4. Start the engine. SeeStart Engine.
5. Disengage the parking brake:
a. Fully push DOWN on the brake pedal.
b. Push DOWN on the parking brake control.
c. Release the brake pedal.
6. Push down on the forward speed control pedal (Q) to
travel forward. Release the pedal to stop.
Note:The further down the pedal is pushed down the faster
the tractor will travel.
7. To stop the tractor, release the speed control pedals, set
the parking brake, and stop the engine. SeeStop Tractor
 and Engine.
Cruise Control
To engage:
1. Push down on the forward ground speed pedal (Q,
Figure1). SeeFeatures and Controls.
2. Pull up the cruise control (S) when the desired speed
is reached. The cruise will lock in one of its five locking
positions.
To disengage:
1. Push down on the brake pedal (P). SeeFeatures and
Controls,OR
2. Push down on the forward ground speed pedal (Q).
Not for
Reproduction
13
Mowing
DANGER
This machine is capable of amputating hands and feet, and
throwing objects. Failure to observe the following safety
instructions could result in serious injury or death.
Only operate the machine in daylight hours or good
artificial light.
Avoid holes, ruts, bumps, rocks, or other hidden
hazards.
Uneven terrain can overturn the machine or cause
operator to lose their balance or footing.
Do not direct discharge material toward anyone. Avoid
discharging material against a wall or obstruction as
material may ricochet back toward the operator.
Stop the blade(s) when crossing gravel surface.
Do not leave a running machine unattended. Always
park on level ground, disengage the attachment, set
parking brake, stop engine and remove starter insert or
key.
1. Engage the parking brake control (B,Figure3).
2. Make sure the PTO switch (D)is disengaged.
3. Start the engine. SeeStart Engine.
4. Set the throttle control (I)to the FAST position.
5. Engage the PTO to activate the mower blades.
6. Use the Height-of-Cut Electric Switch (T)to set the cutting
height to the desired level. SeeAdjusting the Mower
Cutting Height.
7. Disengage the parking brake, then begin to mow.
8. Turn off the PTO.
9. STOP the engine. SeeStop Tractor and Engine.
WARNING
The engine will shut off if the reverse ground speed pedal
is depressed while the PTO is on and the RMO has not
been activated. The operator must always turn the PTO off
prior to driving across on roads, paths, or areas that can be
used by other vehicles. Sudden loss of drive could create a
hazard.
Adjust Mower Cutting Height
The mower lift lever (N, Figure3)lowers the deck to cutting
position or raises the deck to transport position.
To lower the deck:
1. Pull back slightly on the mower lift lever.
2. Push the mower lift lever to the left.
3. Move the mower lift lever down.
To raise the deck:
1. Pull up on the mower lift lever.
2. Lock in notch to the right.
Note:Do not cut when raised in transport position.
The cutting height electric switch (T, Figure3)controls
the mower cutting height. The electric switch adjusts the
cutting height between 1.5 inches and 3.5 inches (2.5 cm
and 8.89 cm). SeeSpecificationssection for height-of-cut
specification.
Reverse Mowing Option (RMO)
DANGER
Mowing in reverse can be hazardous to bystanders.
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
Keep children out of the operating area and under the
watchful care of a responsible adult.
Do not carry passengers, especially children, even
with the blade(s) shut off. Children can fall off and be
seriously injured or interfere with the safe machine
operation. Children who have been given rides in
the past can suddenly appear in the mowing area for
another ride and be run over or backed over by the
machine.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while
backing.
If the machine mows in reverse without Reverse
Mowing Option activated, see an authorized dealer
immediately.
The Reverse Mowing Option (RMO) lets the operator mow in
reverse.
To activate:
1. Engage the Power Take-Off (PTO) (D, Figure3).
2. Turn the Reverse Mowing Option (RMO) key (A)to the
ON position.
3. The L.E.D. light comes on.
4. The operator mows in reverse.
Not for
Reproduction
14
Note:The key must be removed to restrict access to the
RMO.
Maintenance
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic
amputation, or laceration.
Before performing adjustments or repairs:
Disconnect the spark plug wire and keep it away from
the spark plug.
Disconnect battery at negative terminal (only engines
with electric start).
Use only correct tools.
Do not tamper with governor spring, links, or other parts
to increase engine speed.
Replacement parts must be of the same design and
installed in the same position as the original parts.
Other parts may not perform as well, may damage the
unit, and may result in injury.
Do not strike the flywheel with a hammer or hard object
because the flywheel may shatter during operation.
Maintenance Schedule
RIDER AND MOWER
Every 8 Hours or Daily
Safety interlock system check
Remove unwanted material from the rider, mower deck, and engine
compartment
Every 25 Hours or Annually*
Tire pressure check
Mower blade stopping time check
Do a checkfor loose hardware on the rider and mower
Every 50 Hours or Annually*
Clean battery and cables
Rider brakes check
See a Briggs & Stratton Authorized Service Dealer Annually
Lubricate the rider and mower
Mower blades check**
* Whichever come first.
** Do a mower blades check more often in regions with sandy soils or
high dust conditions.
ENGINE
First 5 Hours
Change engine oil
Every 8 Hours or Daily
Engine oil level check
Every 25 Hours or Annually*
Clean the air filter and pre-cleaner**
Every 50 Hours or Annually*
Change the engine oil
ENGINE
Replace the oil filter
Annually
Replace the air filter
Replace the pre-cleaner
See Dealer Annually to
Inspect the muffler and spark arrester
Replace the spark plugs
Replace the fuel filter
Clean the air cooling system
* Whichever comes first.
** Clean more often in dusty conditions or when airborne material is
present.
Tire Pressure Check
For correct traction and best mowing performance, make sure
that the tire inflation pressure is 12-14 psi (0,82-0,96 bar).
Refer to Tire Pressure Check in theMaintenance Schedule.
Also, see Tire Inflation Pressure in theSpecificationssection.
Note:The Tire Inflation Pressure can be slightly different from
the "Maximum Inflation" shown on the side of the tires.
Battery Maintenance
WARNING
When removing or installing battery cables, disconnect the
negative cable FIRST and reconnect it LAST. If not done in
this order, the positive terminal can be shorted to the frame
by a tool.
Cleaning the Battery and Cables
1. Disconnect the NEGATIVE (black) cables first.
2. Disconnect the POSITIVE (red) cables last.
3. Remove the battery as shown in Figure7.
4. Clean the battery surface with baking soda and water.
5. Clean the battery terminals and cable ends with a wire
brush and battery terminal cleaner until shiny.
6. Lubricate the battery terminals with petroleum jelly or
non-conducting grease.
7. Install the battery.
8. Connect the POSITIVE (red) cables first.
9. Connect the NEGATIVE (black) cables last.
Charge the Battery
WARNING
Keep open flames and sparks away from the battery; the
gasses coming from it are highly explosive. Ventilate the
battery well during charging.
A dead battery or one too weak to start the engine can be the
result of a defect in the charging system or other electrical
Not for
Reproduction
15
component. If there is any doubt about the cause of the
problem, see your dealer. If you need to replace the battery,
follow the steps underClean the Battery and Cables.
To charge the battery, follow the instructions provided by the
battery charger manufacturer as well as all warnings included
in the safety rules sections of this book. Charge the battery
until fully charged. Do not charge at a rate higher than 10
amps.
Mower Blade Stop Time
WARNING
If the mower blade does not come to a complete stop within
5 seconds, the clutch must be adjusted. Do not operate the
machine until the correct adjustment has been performed by
anBriggs & Stratton Authorized Service Dealer.
The mower blades and mower drive belt must stop within
five seconds after the electric Power Take-Off (PTO) switch
turns OFF. If the mower drive belt does not stop within five
seconds, see a Briggs & Stratton Authorized Service Dealer
for repairs.
Change the Engine Oil
1. Run engine until warm.
2. Put the rider on a level surface. Refer to Figure8.
3. Stop the engine. Turn the key (A, Figure8) to the OFF
position, and then remove it.
4. Clean the oil fill and oil filter areas of debris.
5. Remove the dipstick (B).
6. Disconnect the oil drain hose (A,Figure9).
7. Carefully remove the cap (B)and lower the hose into an
approved container (C).
8. After the oil has drained, install cap tightly, then attach the
hose to the side of the engine.
9. Remove the oil filter (B,Figure10) and discard.
10. Lightly lubricate the oil filter gasket (A)with clean oil.
11. Install the oil filter by hand until the gasket touches the oil
filter adapter (C). Tighten the oil filter 1/2 to 3/4 turns.
12. Add oil. SeeCheck and Add Engine Oilsection.
Air Filter Assembly (Cartridge with pre-
cleaner)
WARNING
Never start or run the engine with the air cleaner assembly
or air filter removed as it is a fire hazard.
NOTICE
Do not use pressurized air or solvents to clean the filter.
Pressurized air can damage the filter and solvents will
dissolve the filter.
1. Loosen the fasteners (A, Figure11) and remove the
cover (B).
2. Remove the air cleaner assembly (C) and disassemble.
3. Clean up any possible debris that might get into the
carburetor throat (D).
4. Remove the pre-cleaner from the air filter.
5. To loosen debris, gently tap the air filter on a hard
surface. If the air filter is excessively dirty, replace with a
new air filter.
6. Wash the pre-cleaner in liquid detergent and water. Then
allow it to thoroughly air dry. Do not oil the pre-cleaner.
7. Assemble the dry pre-cleaner to the air filter.
8. Install the air filter assembly.
9. Install the cover and secure the fasteners.
Check the Spark Plugs
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic
amputation, or laceration.
When testing for spark:
Use approved spark plug tester.
Do not check for spark with spark plug removed.
NOTICE
Spark plugs have different heat ranges. It is important that
the correct spark plug is used, otherwise, engine damage
can occur. Replace the spark plug with the same type or
equivalent one.
Clean Spark Plug
Clean with wire brush and sturdy knife. Do NOT use
abrasives.
Check Spark Plug Gap
Use a spark plug feeler gauge (A, Figure12) to check the
gap between the two electrodes. When the gap is correct, the
gauge will drag slightly as you pull it through the gap.
If necessary, use the spark plug gauge to adjust the gap by
gently bending the curved electrode without touching the
center electrode or the porcelain.
Install Spark Plug
Tighten with your fingers, then tighten with a wrench as
shown in Figure13.
180 in-lbs (20 Nm), OR
1/2 turn when you install the original spark plug. 1/4 turn
when you install a new spark plug.
Pushing the Tractor by Hand
1. Disengage the Power-Take-Off switch (D, Figure3).
2. Turn the engine OFF.
Not for
Reproduction
16
3. Pull the levertoward the rear of the unit. Push down to
lock in position. Refer to Figure14.The tractor can now
be pushed by hand.
WARNING
Towing the unit will cause transmission damage. Do not use
another vehicle to push or pull this unit. Do not actuate the
transmission release lever while the engine is running.
Towed Equipment
1. Before you tow the unit, make sure that the hitch is
designed for towing.
2. Attach towed equipment ONLY at the hitch point.
3. For towed equipment and towing on slopes, follow the
weight limit recommendationslisted below.
Gross weight (trailer and load) of 400 lb (181.4 kg).
Maximum of 20 lb (9.1 kg) foot up or down on the
tongue.
Go from a 10° limit to a 5°limit on any slope.
4. DO NOT let children or others in or on towed equipment.
5. The weight of the towed equipment on slopes can cause
loss of traction and loss of control.
6. DO NOT shift to neutral and coast down hill.
Clean the Mower Deck (if equipped)
Note:
Use the washout port (C,Figure15) to clean the underside of
the mower deck.
1. Put the rider on a smooth level surface.
2. Attach the quick disconnect (A,Figure15) to the garden
hose (B)and then connect to the washout port (C)on the
mower deck.
3. Turn the water ON.
4. Start the engine.
5. Set the Height-of-Cut in the highest position.
6. Engage the Power Take-Off (PTO) switch to activate the
mower blades. The rotation of the blades and the running
water will clean the underside of the mower deck.
7. Disconnect the Power Take-Off and stop the engine.
8. Turn the water OFF.
9. Remove the garden hose and quick disconnect from the
washout port (C).
Storage
WARNING
Never store the unit (with fuel) in an enclosed, non-
ventilated structure. Fuel vapors can travel to an ignition
source (such as a furnace, water heater, etc.) and cause an
explosion.
Store away from furnaces, stoves, water heaters, or
other appliances that have pilot lights or other ignition
sources because they can ignite fuel vapors.
Equipment
Turn OFF the Power Take-Off (PTO), and set the parking
brake. Remove the starter insert.Let the machine cool.
If you remove the battery, the battery life will increase. Make
sure that thebattery is in a cool, and dry location, and keep
it fully charged. If the battery is left in the unit, disconnect the
negative cable.
Fuel System
Fuel can become stale when stored over 30 days. Stale fuel
causes acid and gum deposits to form in the fuel system or
on essential carburetor parts. To keep fuel fresh, useBriggs
& Stratton® Advanced Formula Fuel Treatment &
Stabilizer, available wherever Briggs & Stratton genuine
service parts are sold.
Before starting the machine after it has been stored:
Check all fluid levels. Check all maintenance items.
Do all recommended checks and procedures found in this
manual.
Make sure the engine is warm before you use it.
Not for
Reproduction
17
Troubleshooting
WARNING
To avoid serious injury, perform maintenance on the tractor or mower only when the engine is stopped and the parking brake
engaged.
To prevent accidental starting of the engine, before maintenance, always remove the ignition key, disconnect the spark plug
wire, and fasten it away from the plug.
Troubleshooting the Rider
PROBLEM LOOK FOR REMEDY
The brake pedal is not pushed down. Fully push down on the brake pedal.
Empty the fuel tank. If engine is hot, let the engine cool, then fill the fuel
tank.
The PTO switch is set to the ON position. Set the PTO switch to the OFF position.
The cruise control is engaged. Move the cruise control knob to the NEUTRAL/OFF
position.
The engine is flooded. Disconnect the choke.
The battery terminals require cleaning. Refer toClean the Battery and Cables.
The battery discharged oris dead. Charge or replace thebattery.
The engine will not turnover or start.
Loose or broken wiring. Visually inspect the wiring. If wires are frayed or
broken, see an Authorized Service Dealer.
Engine starts hard or operates poorly. The fuel mixture is too rich. Clean the air filter.
Low oil level. Inspect and add oil as required.Engine knocks.
Incorrect grade of oil. Refer to theStart and Stop Enginesection.
Incorrect grade of oil. Refer to theStart and Stop Enginesection.Too much oil.
There is too muchoil in crankcase. Drain remaining oil.
The air filter is dirty. Refer to theService the Air Filtersection.Engine exhaust is black.
The choke is closed. Open the choke.
The speed control pedals are not pushed down. Push down on the speed control pedals.
The transmission release lever is in PUSH
position.
Move the transmission release lever into DRIVE
position.
Engine runs, but rider will not drive.
The parking brake is engaged. Release the parking brake.
Rider steers hard or handles poorly. Incorrect tire inflation. Refer to theCheck Tire Pressuresection.
Note:For all other problems, contact an Authorized Service Dealer.
Troubleshooting the Mower
PROBLEM LOOK FOR REMEDY
The mower cut is uneven. The rider tires are incorrectly inflated. Refer to theCheck Tire Pressuresection.
The engine speed is set to slow. Set to FAST throttle.The mowercut looks rough.
The ground speed is set to fast. Slow down.
The engine speed is set to slow. Set to FAST throttle.
The ground speed is set to fast. Slow down.
The air cleaner is clogged or dirty. Refer to theService Air Filtersection.
The Height-of-Cut set too low. Cut tall grass at maximum Height-of-Cut during first
pass.
The engine is not up to operating temperature. Operate the engine for several minutes to warm
up.
The engine stalls easily with the mower engaged.
The grass is too tall. Start the mower in a cleared area.
The engine turns ON, and the rider drives, but the
mower will not cut.
PTO not engaged. Engage PTO.
Note:For all other problems, contact an Authorized Service Dealer.
Not for
Reproduction
18
Specifications
Specifications Chart
The spark ignition system on this rider complies with Canadian standard ICE-002.
Item 2691481, 2691487 2691482, 2691488, 2691576 2691483, 2691489
Engine Intek™Briggs & Stratton Intek™Briggs & Stratton Professional Series™Briggs &
Stratton
Displacement 656 cc 656 cc 725 cc
Electrical System 9-Amp 9-Amp 9-Amp
Battery 12V - 195CCA 12V - 195CCA 12V - 230CCA
Oil Capacity 64 oz (1,9 L) 64 oz (1,9 L) 64 oz (1,9L)
Spark Plug Gap .030 in (,76 mm) .030 in (,76 mm) .030 in (,76 mm)
Spark Plug Torque 180 lb-in (20 Nm) 180 lb-in (20 Nm) 180 lb-in (20 Nm)
Fuel Tank Capacity 13.2 L 13.2 L 13.2 L
Transmission
Make and Type
Tuff Torq
®
K46 Tuff Torq
®
K46 Tuff Torq
®
K46
Mower Deck
Cutting Width 42 in (107 cm) 46 in (117 cm) 48 in (122 cm)
Number of Blades 2 standard lift 3 standard lift 3 standard lift
Height-Of-Cut 1.5 - 4.0 in (3,8 - 10,2 cm) 1.5 - 4.0 in (3,8 - 10,2 cm) 1.5 - 4.0 in (3,8 - 10,2 cm)
Chassis
Front Wheel Size 15 x 6-6 15 x 6-6 15 x 6-6
Front Wheel Inflation Pressure 12 - 14 psi (0,82 - 0,92 Bar) 12 - 14 psi (0,82 - 0,92 Bar) 12 - 14 psi (0,82 - 0,92 Bar)
Rear Wheel Size 20 x 8-8 22 x 10-8 22 x 9.5-12
Rear Wheel Inflation Pressure 10 psi (0,68 Bar) 10 psi (0,68 Bar) 10 psi (0,68 Bar)
Power Ratings:The gross power rating for individual
gasoline engine models is labeled in accordance with
SAE (Society of Automotive Engineers) code J1940 Small
Engine Power & Torque Rating Procedure, and is rated in
accordance with SAE J1995. Torque values are derived at
2600 RPM for those engines with “rpm” called out on the
label and 3060 RPM for all others; horsepower values are
derived at 3600 RPM. The gross power curves can be viewed
at www.BRIGGSandSTRATTON.COM. Net power values are
taken with exhaust and air cleaner installed whereas gross
power values are collected without these attachments. Actual
gross engine power will be higher than net engine power
and is affected by, among other things, ambient operating
conditions and engine-to-engine variability. Given the wide
array of products on which engines are placed, the gasoline
engine may not develop the rated gross power when used in
a given piece of power equipment. This difference is due to
a variety of factors including, but not limited to, the variety of
engine components (air cleaner, exhaust, charging, cooling,
carburetor, fuel pump, etc.), application limitations, ambient
operating conditions (temperature, humidity, altitude), and
engine-to-engine variability. Due to manufacturing and
capacity limitations, Briggs & Stratton may substitute an
engine of higher rated power for this engine.
Not for
Reproduction
19
Indholdsfortegnelse:
Produkter omfattet af denne manual................................ 20
Generel information............................................................20
Kontaktoplysninger for europæisk kontor.......................20
Europæiske Union (EU) Trin V (5): Kuldioxid-værdier
(CO2).....................................................................................20
Førersikkerhed ................................................................... 20
Guide til identifikation af skråninger............................... 20
Sikkerhedssymboler og deres betydninger.................... 20
Sikkerhedssymboler og signalord ................................. 21
Sikkerhedsmærkater.......................................................21
Sikkerhedsmeddelelser................................................. 22
Funktioner og betjeningsanordninger..............................22
Faresymboler og deres betydninger...............................23
Betjening..............................................................................24
Betjeningsområde...........................................................24
Afprøvning af sikkerhedslåsesystem..............................24
Elektronisk instrumentpanel .......................................... 25
Motor...............................................................................25
Betjening af traktor......................................................... 27
Græsslåning................................................................... 28
Justering af plæneklipperens klippehøjde......................28
Vælg baglæns plæneklipning (RMO) ............................ 28
Vedligeholdelse...................................................................29
Vedligeholdelsesskema.................................................. 29
Kontroller dæktrykket......................................................30
Vedligeholdelse af batteri...............................................30
Afprøv klipperknivenes standsningstid........................... 30
Skift motorolien...............................................................30
Luftfiltersamling (patron med forfilter).............................30
Kontrollér tændrørene.................................................... 31
Manuel betjening af traktoren.........................................31
Bugsering af udstyr........................................................ 31
Rengør klippeaggregatet (hvis monteret).......................31
Opbevaring.......................................................................... 32
Fejlfinding............................................................................ 33
Fejlfinding for plæneklipperen ....................................... 33
Fejlfinding af plæneklipperen ........................................ 33
Specifikationer.....................................................................34
Specifikationsoversigt..................................................... 34
Not for
Reproduction
20
Produkter omfattet af denne
manual
De følgende produkter er omfattede af denne manual:
2691481-00, 2691481-01,2691481-02,2691482-00,
2691483-00, 2691487-00, 2691487-01,2691487-02,
2691488-00, 2691489-00, 2691576-00.
Generel information
For yderligere information henviser vi til
Kundekontaktvejledning inkluderet med enheden.
Illustrationerne i dette dokument er repræsentative. Din
enhed kan se anderledes ud end de viste billeder. VENSTRE
og HØJRE er refereret til, fra betjeningspositionen.
Brugen af Vigtigt og Bemærk i teksten indikerer afklaringer,
undtagelser eller alternativer til de givne procedurer.
Alle sprogoversættelse af dette dokument er udført med
udgangspunkt i den oprindelige engelske kildefil.
Al emballage, brugt olie og batterier skal bortskaffes
med henblik på genbrug i henhold til de gældende
regeringsbestemmelser.
Kontaktoplysninger for
europæisk kontor
For spørgsmål vedrørende europæiske emissioner bedes du
kontakte vores europæiske kontor på:
Max-Born-Straße 2, 68519 Viernheim, Tyskland.
Europæiske Union (EU) Trin V
(5): Kuldioxid-værdier (CO
2
)
Briggs & Strattons EU-typegodkendelsescertifikat-
motorers kuldioxid-værdier kan findes ved at indtaste CO2 i
søgevinduet på BriggsandStratton.com.
Førersikkerhed
Opbevar denne vejledning til senere brug.Denne
vejledning indeholder sikkerhedsoplysninger for at gøre
dig opmærksom på de farer og risici, der er forbundet med
produktet, og hvordan man undgår dem. Den indeholder også
vigtige instruktioner, der skal følges ifm. den første indstilling,
betjening og vedligeholdelse af produktet.
Dette produkt er udelukkende konstrueret og beregnet til
slåning af velholdt græs. Det er ikke beregnet til noget andet
formål.
Det er vigtigt, at du læser og forstår disse instruktioner, før du
forsøger at starte eller betjene dette udstyr.
Sørg for, at du er helt fortrolig med betjeningsanordningerne
og korrekt brug af produktet.
Lær, hvordan du hurtigt stopper enheden og afbryder
kontrolanordningerne.
Guide til identifikation af skråninger
Sådan måles hældningen af en græsplæne med en
smartphone eller et vinkelmåleværktøj:
ADVARSEL
Må ikke bruges på skråninger, der overgår10graderne.
1. Brug en genstand med en lige kant på mindst 60 cm (A,
figur1). Et stykke tømmer på 2 x 4 eller et lige stykke
metal er velegnede til dette.
2. Vinkelmåleværktøj.
a. Brug din smartphone:Mange smartphones
(B, figur1) har et inklinometer (til vinkelmåling) i
deres kompasapp. Ellers søg i App Store efter en
inklinometer-app. 
b. Brug vinkelmåleværktøj:Vinkelmåleværktøj (C
og D, figur1) fås i de fleste byggemarkeder eller
online (kaldes også inklinometer, krængningsmåler,
hældningsmåler eller vinkelmåler). Typer med skive
(C) eller digitale typer (D) fungerer, hvorimod andre
evt. ikke fungerer. Følg brugervejledningen for
vinkelmåleværktøjet.
3. Placér den 60 cm lange lige kant langs den stejleste del
af græsplænen. Læg pladen, så den ligger lige op og ned
ad skråningen.
4. Læg smartphonen eller vinkelmåleværktøjet på den lige
kant og aflæs vinklen igrader. Det er din græsplænes
hældning. 
Bemærk:Der medfølger en trykt guide til identifikation af
hældning i de tryksager, der er vedlagt produktet, og den
findes ligeledes som download på producentens webside.
Sikkerhedssymboler og deres
betydninger
Symbol  Betydning
Sikkerhedsinformation om farer, som kan resultere i
personskade. 
Læs og forstå brugervejledningen, før brug af eller
servicering af enheden.
Fjern nøglen og læs brugervejledningen før du servicerer
enheden.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192

Simplicity 2691481-00 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur