MARTIN LOGAN Statement 40XW Manuel utilisateur

®

In-Wall Backbox Install Manual

2

WARNING!

• Refer servicing to a qualified technician.

• To prevent fire or shock hazard, do not

expose this module to moisture.

• Turn the amplifier off should any abnormal

conditions occur.

• Do not drive speaker beyond its rated power.

Content Check List.........................3

Connection ..............................4

Protect Your Investment .....................4

Break-In ................................4

Speaker Placement ........................4

Achieving Superior Imaging . . . . . . . . . . . . . . . . . . . .4

Balancing Hard vs. Soft Surfaces Improves

High- and Mid-Frequency Performance ............4

Painting the Speaker Grille ..................5

Pre-Installation Checklist....................6

Part Identification .........................7

Installation ..........................8 - 22

Attaching Bottom Bracket......................8

Back Box Preparation.........................9

Back Box Installation ........................10

Connect Speaker Wire.......................11

Positioning the Install Board ...................12

Securing the Install Board.....................13

Adjusting the Install Board ....................14

Attach Sheet Rock Clips ......................15

Hang the Sheet Rock ........................16

Mating Sheet Rock to the Install Board ...........17

Break Off Sheet Rock Clip Fingers ..............18

Sheet Rock Finishing Preparation ...............19

Sheet Rock Finishing Part 1....................20

Sheet Rock Finishing Part 2....................21

Painting Tips ..............................22

Dimensional Drawing .....................23

Per the European Union WEEE (Waste Electrical and

Electronic Equipment) directive effective August 13,

2005, we would like to notify you that this product

may contain regulated materials which upon disposal,

according to the WEEE directive, requires special reuse

and recycling processing. For this reason, Martin Logan

has arranged with our distributors in European Union

member nations to collect and recycle this product at

no cost to you.

To find your local distributor, please contact the dealer

from whom you purchased this product, email

[email protected] or visit the distributor locator at

www.martinlogan.com.

Please note, only this product itself falls under the

WEEE directive. When disposing of the packaging and

other related shipping materials, we encourage you to

recycle these items through the usual channels.

The lightning bolt flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to

constitute a risk of electric shock.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

The fire within an equilateral triangle is intended

to alert the user to the potential of creating a fire

hazard if they do not follow the instructions.

The dollar sign within an equilateral triangle is

intended to alert the user that they run the risk

of causing damage that could be potentially

expensive to repair if they don’t follow the

instructions.

3

Content Check List

The Statement 40XW In-Wall Kit ships in 2 boxes and includes the following items. Should you require assistance,

please call our service department at (785) 749-0133.

Box 1: “Backbox Installation Pack”

In Wall Back Box •2x Mounting Brackets •1x Bracket Spacer •10x Wood Screws (Packaged with Mounting Brackets)

Box 2: “Install Board Hardware Kit”

Install Board •Hardware Pack (12x Wood Screws •14x Sheet Rock Clips •14x Sheet Rock Screws)

Box 1

Box 2

4

These speakers are designed with easy-to-use push-style

binding posts that accept bare wire (fig. 1).

Assign the same color to the (+) and (–) terminals on both the

speaker and the amplifier. Make sure that all connections are

tight.

For convenience during the installation process, Statement

40XW has binding posts on both the top and bottom of the

enclosure. CONNECT TO ONLY 1 SET OF BINDING POSTS.

ConneCtion

• Use an amp that approximately matches the speaker’s

specified power handling.

• To avoid damage, turn down the volume of the

speaker is distorting, sounds harsh, or the bass begins

to break up.

• Tone controls and equalizers may increase the

likelihood of distortion, especially at high volumes. Use

these setting sparingly.

When you first begin to play your speakers, they may sound

a bit bass shy, due to the high quality, long-life components

used in the drivers. Allow approximately 72 hours of break-in at

90 dB (moderate listening levels) before any critical listening.

Break-in

ProteCt Your investment

Achieving Superior Imaging

For best performance and imaging, place the speakers

equidistant to the primary listening position. It is

recommended that the primary listening position be 1x -2x

the distance between the speakers for optimal imaging. For

example, if your speakers are 10 feet apart, then the optimal

listening distance is between 10 and 20 feet away. Guidance

for speaker height can be found on page 6 in the “Pre-

Installation Checklist” section.

Balancing Hard vs. Soft Surfaces Improves High- and

Mid-Frequency Performance

Rooms that are “overdamped” with carpeting, drapes, and

other sound absorbers can cause your system to be dull

and lifeless. On the other hand, rooms can have so many

hard surfaces that the system sounds like a gymnasium.

Experiment by adding or removing soft surfaces until you find

a mix that is right for you.

sPeaker PlaCement

Fig. 1

WARNING! Turn your amplifier off before

making or breaking any signal connections!

5

Painting the sPeaker grille

IMPORTANT!

The Statement 40XW grille is packaged with the

driver assembly (STATE40XW) and not in the same packaging

as the install kit. The speaker includes an extra scrim.

1. Remove the grille from the speaker. A protective cloth

scrim is attached to the back of the grille with a low-tack

adhesive. Remove this scrim by gently pulling it away

from the grille and discard it.

2. Paint the grille, being careful not to plug the holes.

Allow the paint to dry completely before proceeding.

IMPORTANT! For best results use a spray rather than a

brush or roller.

3. Gently press the new scrim into place before reinstalling

the speaker grille.

6

Pre-installation CheCklist

NOTE: These instructions assume the mounting surface is of

standard wood frame and conventional sheetrock construc-

tion. If you wish to mount the speakers to another type of

material, you should contact a bonded contractor.

NOTE:

See your local dealer for new construction pre-

install brackets (sold separately).

WARNING! Before installing check local

building codes to verify compliance with local

regulations. WARNING!

Before installing

check for obstructions behind drywall. To do

this make a small cut-out, cutting at a 45°

angle (this makes the hole easier to patch if

you find obstacles. Only cut out the mounting

hole after you have verified there are no

obstructions behind the drywall. WARNING!

Use speaker cable rated for in-wall use.

The UL standard is CL2, CL3, and CM. The

CSA standard is FT4. WARNING! Turn your

amplifier off before making or breaking any

signal connections.

1. Be sure the wall framing is plumb and the stud spacing

is correct. (16” Minimum - 18” Maximum on center

stud spacing)

2. Speaker wire should be ran to each of the designated

stud bays before beginning the install. The in wall

back box has binding posts on the top and bot-

tom for ease of connection only. Statement

40XW requires that only 1 connection be made.

3. Please ensure the chosen stud bays are clear of all

obstructions. If plumbing, electrical, or another obstruc-

tion is present that cannot be safely relocated, please

consult the back box dimensional drawing to verify

potential fitment interference

A simple and effective way to test for potential fitment

issues is to use one of the included back box mounting

brackets as a check gauge- placing it in the stud bay and

moving it over possible interferences. If anything makes

contact with the bracket, it will interfere with the back box

and must be relocated in order to use that stud bay.

4. The overall height of the Statement 40XW drivers is

around 53” tall. We recommend that the seated ear

level at the primary listening position(s) fall within the

middle 40” of the driver assembly. Essentially making

sure that ear level is around 6.5” or more above the

bottom of the lowest speaker driver. Please note, that

the height of the in-wall enclosure will be the ultimate

limiting factor on how high the speaker can be mounted

within the stud bay. The large height of the driver

assembly means that most typical seating heights will be

well within the “sweet spot” of the speaker.

Tools you’ll need before sheet rock work:

-Tape Measure

-Laser Level (recommended)

-Ladder

-Power drill/driver

-#2 Phillips driver bit

-#2 Phillips Hand Screwdriver

-Wire Strippers

Sheet rock installation/finishing:

-Mesh sheetrock tape

-45 minute sheetrock joint compound

-Lightweight sheetrock mud

-Medium Grit Sanding Sponge

-½” or 5/8” sheet rock (depends on installation

requirements)

-General sheetrock finishing equipment

PLEASE NOTE: INSTALLATION IS A 2 PERSON JOB.

7

Part identifiCation

1

2

3

7

8

3

66

5

4

1 Install Board

2 Positioning Brackets

3 Mounting Brackets

4 Alignment Pins

5 Back Box

6 Positioning Bracket Pockets

7 Positioning Board

8 Bracket Spacer

8

installation

STEP 1: CRUCIAL STEP! ATTACHING THE BOTTOM

BRACKET

1a Mark the desired bracket height from the floor on

the studs.

1b Ensure the bracket is level using the attached bubble

level. Once level, attach the bracket to the studs with

(4) included wood screws. Metal studs will require

different screws that are not included.

1c Apply (1) spacer to the top of the bracket as shown, by

peeling the backer off of the attached adhesive tape.

A simple and effective way to test for potential fitment

issues is to use one of the included back box mounting

brackets as a check gauge- placing it in the stud bay

and moving it over possible interferences. If anything

makes contact with the bracket, it will interfere with the

back box and must be relocated in order to use that

stud bay.

1d Repeat the steps above for any additional 40XW bottom

brackets, if installing multiples. Use a laser level to

ensure the speakers will be on the same plane once

installation is complete.

9

STEP 2: BACK BOX PREPARATION

2a Carefully remove the back box from its packaging.

Confirm the proper orientation of the back box using the

diagram on the positioning board:

LC UP = LEFT CHANNEL UP

RC UP = RIGHT CHANNEL UP

2b With the correct orientation pointing upwards, seat the

remaining bracket on the top of the back box by guid-

ing the locating pins on the back box into the holes in

the top bracket. Top bracket should be oriented as

depicted in the figure

10

STEP 3: BACK BOX INSTALLATION

3a With the correct orientation pointing upwards, lift the

back box and seat it into the holes in the bottom bracket

spacer using the locating pins for alignment.

3b Carefully push the back box into the stud bay. Please

ensure the top bracket can sit flush against the studs just

like the bottom bracket. A helper should now hold the

back box in place to complete the next step.

3c While the back box is being held in place, ensure the top

bracket is seated down firmly on the top of the back box.

Then secure the bracket to the studs with (4) supplied

wood screws. Metal studs will require different

screws that are not included.

11

STEP 4: CONNECT SPEAKER WIRE TO TOP OR BOT-

TOM BINDING POSTS

4a Connect the speaker wire to either the top binding

posts OR bottom binding posts. The in wall back box

has binding posts on the top and bottom for ease of

connection only. Statement 40XW requires that only

1 connection be made. DO NOT CONNECT AN

AMPLIFIER CHANNEL TO BOTH THE TOP AND

BOTTOM, USE ONLY 1.

12

STEP 5: POSITIONING THE INSTALL BOARD

5a Carefully remove the install board from its packaging.

Ensure the install board thickness matches that of the

intended wall surface. Both 1/2” and 5/8” kits are

available.

5b Position the install board on the back box by seating the

positioning brackets into the pockets on the positioning

board. Ensure all brackets are fully seated and touching

the bottom of their respective pockets.

13

STEP 6: SECURING THE INSTALL BOARD

6a Secure the install board to the studs through the 12

slots indicated above using the (12) included wood

screws. Metal studs will require different screws

that are not included.

x 12

14

STEP 7: CRUCIAL STEP! ADJUSTING THE

INSTALL BOARD

7a The adjustment blocks on the install board allow for

fine tuning of the speaker opening, ensuring perfect

alignment of the finished installation. To lock in the

desired install board adjustments, tighten the 12

adjustment blocks hand-tight with a Phillips screw driver.

7b You may need to push in and hold down an adjustment

bracket so it sits flush in it’s pocket while tightening the

adjustment blocks. The goal is to make sure the install

board sits as tight as possible to the positioning board

first- and then locking in that position by tightening the

adjustment block. Repeat for each of the 12 adjustment

blocks as necessary.

7c After tightening all the adjustment blocks, push on the

install board. If it can flex in any area, tighten the nearest

adjustment block further.

15

STEP 8: ATTACH SHEET ROCK CLIPS

8a Attach the included sheetrock clips to the install board in

the 14 recessed locations around the perimeter. Ensure

the “fingers” are facing forward.

8b Drive (1) included sheet rock screw through the face of

the install board and into the sheet rock clip for each

location as shown.

16

STEP 9: HANG THE SHEET ROCK

9a Hang the sheet rock on the stud wall. The opening

around the Fiberock® install board can be measured

and cut before application. Alternatively, sheet rock

can be loosely hung over the install board and then an

opening cut with a drywall saw using the perimeter of

the install board as a guide. If using this method, avoid

cutting into the sheet rock clips.

NOTE:The surfaces of the sheet rock and install

board will not be on the same plane. The clips

force the sheet rock to be proud of the install board

surface. This is done intentionally.

17

STEP 10: MATING SHEET ROCK TO THE

INSTALL BOARD

10a After securing the sheet rock to the studs as per normal

construction, mate the install board to the surrounding

sheet rock by driving a screw through the sheet rock

into the other end of the sheet rock clip behind it. For

easy reference, the clips will be directly across from the

locations used in step 8.

10b When bridging the joint in two pieces of sheet rock, be

sure to secure both to the clip. Example shown in the

magnified insert above.

18

STEP 11: BREAK OFF DRYWALL CLIP FINGERS

11a Snap off the drywall clip fingers using a back and forth

motion as shown in the figure below.

19

STEP 12: SHEET ROCK FINISHING PREPARATION

12a Apply mesh sheet rock tape to joints and slots as indi-

cated in the diagram.

WARNING: Mesh sheet rock tape

is required. Do not use traditional

paper sheetrock tape.

20

STEP 13: SHEET ROCK FINISHING PART 1 - JOINT

COMPOUND APPLICATION

13a Apply quick 45 minute joint compound to the install

board. As noted in Step 9, the sheet rock will be

sitting proud of the install board surface. Apply joint

compound to the face of the install board, bringing

it up level with the sheet rock. Be sure to fill in the

connecting sheet rock sheet joints

13b After the compound has cured, sand in preparation for

the lightweight coat.

NOTE: The sheet metal face of the install board must

be exposed. Sand the area free of sheet rock mud

buildup before proceeding to the next step.

La page charge ...

MARTIN LOGAN Statement 40XW Manuel utilisateur

Ce manuel convient également à

MARTIN LOGAN Statement 40XW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents