Admiral YNED5800TQ0 Installation Instructions Manual

Marque: Admiral

Modèle: YNED5800TQ0

Catégorie: Sèche-linge électriques

Taper: Installation Instructions Manual

29" (73.7 CM) ELECTRICDRYER

INSTALLATIONINSTRUCTIONS

INSTRUCCIONES DE INSTALACION PAPA LA

SECADORA ELIT:CTRICADE 29" (73,7 CM)

INSTRUCTIONS POUR L'INSTALLATIONDE LA SECHEUSE

IT:LECTRIQUEDE 29" (73,7 CM)

Table of Contents / [ndice / Table des mati@res

DRYER SAFETY ............................................... 1

INSTALLATION INSTRUCTIONS ................... 2

Tools and Parts ............................................. 2

Location Requirements ................................ 2

Electrical Requirements - U.S.A ................... 3

Electrical Requirements - Canada ................ 4

Electrical Connection - U.S.A. Only .............. 5

Venting Requirements ................................. 10

Plan Vent System ........................................ 11

Install Vent System ...................................... 12

Install Leveling Legs .................................... 12

Level Dryer .................................................. 12

Connect Vent .............................................. 12

Reverse Door Swing (Optional) ................... 12

Complete Installation .................................. 13

SEGURIDAD DE LA SECADORA ................. 14

INSTRUCCIONES DE INSTALACION .......... 14

Herramientas y piezas ................................. 14

Requisitos de Iocalizacion ......................... 14

Requisitos el_ctricos - U.S.A ...................... 15

Conexi6n el_ctrica - U.S.A. Only ................ 17

Requisitos de ventilaci6n ............................ 22

Planificaci6n del sistema de ventilaci6n ..... 23

Instalacion del sistema de ventilacion ........ 24

Instalacion de las patas niveladoras ........... 24

Nivelaci6n de la secadora ........................... 24

Conexi6n del ducto de escape ................... 25

Como invertir el cierre de la puerta

(opcional) ..................................................... 25

Complete la instalaci6n ............................... 26

SECURITE DE LA SECHEUSE ..................... 27

INSTRUCTIONS D'INSTALLATION .............. 28

Outillage et pi_ces ....................................... 28

Exigences d'emplacement ......................... 28

Specifications _lectriques - Canada ........... 30

Exigences concernant 1'6vacuation ............ 30

Planification du systeme d'_vacuation ....... 32

Installation du systeme d'_vacuation ......... 33

Installation des pieds de nivellement .......... 33

Mise & niveau de la s_cheuse ..................... 33

Raccordement du conduit d'6vacuation .... 34

Inversion de I'ouverture de la porte

(facultatif) ..................................................... 34

Achever I'installation ................................... 35

DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

W10088970

INSTALLATIONINSTRUCTIONS

• If you are using a power supply cord, a grounded electrical

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Flat-blade screwdriver

#2 Phillips screwdriver

Adjustable wrench that

opens to 1" (2.54 cm) or

hex-head socket wrench

(for adjusting dryer feet)

Wire stripper (for U.S.

only, direct wire

installations)

• Tin snips(new vent

installations)

• Level

• Vent clamps

• Caulking gun and

compound (for installing

new exhaust vent)

• Tape measure

Parts supplied:

Remove parts package from dryer drum. Check that all parts were

included.

4 leveling legs

Parts needed:

Check local codes, check existing electrical supply and venting

and see "Electrical Requirements" and "Venting Requirements"

before purchasing parts.

Mobile home installations require metal exhaust system hardware

available for purchase from the dealer from whom you purchased

your dryer. For further information, please reference the

"Assistance or Service" section of the Dryer User Instructions.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 era) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See

"Venting Requirements."

• Aseparate 30-amp circuit.

outlet located within 2ft (61 cm) of either side of the dryer. See

"Electrical Requirements."

• A sturdy floor to support the total weight (dryer and load) of

200 Ibs (90.7 kg). The combined weight of a companion

appliance should also be considered.

• A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer. (If slope is greater than 1" [2.5 cm], install Extended

Dryer Feet Kit, Part Number 279810.) Clothes may not tumble

properly and models with automatic sensor cycles may not

operate correctly if dryer is not level.

Do not operate your dryer at temperatures below 45°F (7°C). At

lower temperatures, the dryer might not shut off at the end of an

automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be

exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes or

sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open

fully.

Dryer Dimensions

...... _ L

15_/4'' h.................... 223/4"

43% _.(38.74cm) 43s/8 _ .'_(57.8cm)

(73.66cm) _ (73.66crn)

c D

A. Small opening side-swing door

B. Large opening side-swing door

C. Wide opening side-swing door

D. Wide opening hamper door

*Most installations require a minimum 5" (12.7 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting

Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this

dryer. This dryer has been tested for spacing of 0" (0 cm)

clearance on the sides and rear. Recommended spacing should

be considered for the following reasons:

• Additional spacing should be considered for ease of

installation and servicing.

• Additionalclearancesmightberequiredforwall,doorand

floormoldings.

• Additionalspacingshouldbeconsideredonallsidesofthe

dryertoreducenoisetransfer.

• Forclosetinstallation,withadoor,minimumventilation

openingsinthetopandbottomofthedoorarerequired.

Louvereddoorswithequivalentventilationopeningsare

acceptable.

• Companionappliancespacingshouldalsobeconsidered.

I I_, I (3b.t_cm)

(310cm2)

(4_.87''

24in.2.

-- __ ._ (155cm2',

1"-_ _ 2e"_ _1" ÷b"*_ 2#/,"_15"*F-

(2.5cm) (73.66cm) (2.5cm)(2.5cm) (70.5cm)(12.7crn)

A B

__ 3"*

(7.6cm)

3,J*

(7.6 cm)

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

*Required spacing

Mobile Home - Additional Installation Requirements

This dryer is suitable for mobile home installations.

The installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD Part 280) or the Canadian Manufactured

Home Standard, CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for

purchase from your dealer.

• Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a

nearby window) should be at least twice as large as the dryer

exhaust opening.

E®CI CO I{;®q ®m®n's-. ,c

It is your responsibility

• To contact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

The National Electric Code requires a 4-wire supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if specified on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A

time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

Do not use an extension cord.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

• If local codes do not permit the connection of a neutral ground

wire to the neutral wire, see "Optional 3-wire connection"

section.

• This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground wire is

permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical

supply connection, the neutral ground wire must be removed

from the external ground conductor screw (green screw), and

secured under the neutral terminal (center or white wire) of the

terminal block. When the neutral ground wire is secured under

the neutral terminal (center or white wire) of the terminal block,

the dryer cabinet is isolated from the neutral conductor.

• A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas

where local codes prohibit grounding through the neutral

conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes

dryers. The kit should contain:

• A UL listed 30-amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be at

least 4 ft (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned

ends.

• A UL listed strain relief.

If your outlet looks like this:

4-wire receptacle (!4-30R)

Then choose a 4-wire power supply cord with ring or spade

terminals and UL listed strain relief. The 4-wire power supply cord,

at least 4 ft (1.22 m) long, must have 4 10-gauge solid copper

wires and match a 4-wire receptacle of NEMA Type

14-30R. The ground wire (ground conductor) may be either green

or bare. The neutral conductor must be identified by a white cover.

If your outlet looks like this:

3-wire receptacle (10-30R)

Then choose a 3-wire power supply cord with ring or spade

terminals and UL listed strain relief. The 3-wire power supply cord,

at least 4 ft (1.22 m) long, must have three 10-gauge solid copper

wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

[] Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), protected with flexible metallic conduit. All

current-carrying wires must be insulated.

[] 10-gauge solid copper wire (do not use aluminum).

[] At least 5 ft (1.52 m) long.

GROUNDING iNSTRUCTiONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

[] For a permanently connected dryer:

This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dryer.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Electrical Shock Hazard

Plug into a grounded 4 prong outlet,

Failure to do so can result in death or electrical shock.

It is your responsibility

[] To contact a qualified electrical installer.

[] To be sure that the electrical connection is adequate and in

conformance with the Canadian Electrical Code, C22.1-latest

edition and all local codes. A copy of the above codes

standard may be obtained from: Canadian Standards

Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3

CANADA.

To supply the required 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply on a separate 30-amp circuit,

fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch

circuit.

This dryer is equipped with a CSA International Certified

Power Cord intended to be plugged into a standard 14-30R

wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure wall

receptacle is within reach of dryer's final location.

4-wire receptacle 14-30R

[] Do not use an extension cord.

If you are using a replacement power supply cord, it is

recommended that you use Power Supply Cord Replacement

Part Number 3394208. For further information, please reference

the service numbers located in the Dryer User Instructions.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE INSTRUCTIONS

Power Supply Cord

Fire Hazard

Use a new UL listed 30 amp power supply cord.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

Direct Wire

Fire Hazard

Use 10 gauge solid copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

B C D

A.Terminalblock cover

B.Externalground conductor screw

C.Center,silver-colored terminal block screw

D.Hold-down screw location

E.Neutral ground wire

E Hole below terminal block opening

3. Install strain relief.

Style 1: Power supply cord strain relief

• Remove the screws from a %" (1.9 cm) UL listed strain

relief (UL marking on strain relief). Put the tabs of the two

clamp sections into the hole below the terminal block

opening so that one tab is pointing up and the other is

pointing down, and hold in place. Tighten strain relief

screws just enough to hold the two clamp sections

together.

A. Strain relief tab pointing up

B. Hole below terminal block opening

C. Clamp section

D. Strain relief tab pointing down

Put power supply cord through the strain relief. Be sure

that the wire insulation on the power supply cord is inside

the strain relief. The strain relief should have a tight fit with

the dryer cabinet and be in a horizontal position. Do not

further tighten strain relief screws at this point.

Style 2: Direct wire strain relief

• Unscrew the removable conduit connector and any

screws from a 3/4"(1.9 cm) UL listed strain relief (UL

marking on strain relief). Put the threaded section of the

strain relief through the hole below the terminal block

opening. Reaching inside the terminal block opening,

screw the removable conduit connector onto the strain

relief threads.

.......................................................g

A. Removable conduit connector

B. Hole below terminal block opening

C. Strain relief threads

Put direct wire cable through the strain relief. The strain

relief should have a tight fit with the dryer cabinet and be

in a horizontal position. Tighten strain relief screw against

the direct wire cable.

Now complete installation following instructions for your type

of electrical connection:

4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be Go to Section

connecting to:

4-wire receptacle A UL listed, 4-wire connection:

(NEMA Type 14-30R) 120/240-volt Power supply cord

_.._ minimum,

30-amp, dryer

power supply

cord*

4-wire direct A fused 4-wire connection:

disconnect or Direct Wire

circuit breaker

box*

(12.7 ore)

3-wire receptacle A UL listed,

(NEMA type 10-30R) 120/240-volt

minimum,

30-amp, dryer

power supply

cord*

3-wire connection:

Power supply cord

3-wire direct A fused 3-wire connection:

disconnect or Direct Wire

circuit breaker

box*

*If local codes do not permit the connection of a cabinet-ground

conductor to the neutral wire, go to "Optional 3-wire connection"

section.

4-wire connection: Power Supply Cord

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire

connections.

B F

C D E G

A. 4-wire receptacle (NEMA type 14-30R)

B. 4-prong plug

C. Ground prong

D. Neutral prong

E.Spade terminals with upturned ends

F. 3_,,(!.9 cm) UL listed strain relief

G. Ring terminals

1. Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor

screw. Connect neutral ground wire and the neutral wire (white

or center wire) of power supply cord under center, silver-

colored terminal block screw. Tighten screw.

A C

A. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to

center silver-colored terminal block screw.

B. Center silver-colored terminal block screw

C. Neutral wire (white or center wire)

D. 3/4,,(1.9 cm) UL listed strain relief

E.Neutral ground wire

Connect ground wire (green or bare) of power supply cord to

external ground conductor screw. Tighten screw.

A. External ground conductor screw

B. Center silver-colored terminal block screw

C. Neutral wire (white or center wire)

D. 3/4"(1.9 cm) UL listed strain relief

E. Ground wire (green or bare) of power supply cord

F Neutral ground wire

4. Connect the other wires to outer terminal block screws.

Tighten screws.

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

7. You have completed your electrical connections. Now go to

"Venting Requirements."

4-wire connection: Direct Wire

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire

connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed.

Strip 5" (12.7 cm) of outer covering from end of cable, leaving

bare ground wire at 5" (12.7 cm). Cut 11/2'' (3.8 cm) from

3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends of

wires into a hook shape.

(12, 7 err

When connecting to the terminal block, place the hooked end of

the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw, as shown.

Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor

screw. Connect neutral ground wire and place the hooked end

(hook facing right) of the neutral wire (white or center wire) of

direct wire cable under the center screw of the terminal block.

Squeeze hooked ends together. Tighten screw.

A B

/'!

.......C

b /

A. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to

center silver-colored terminal block screw.

B. Center silver-colored terminal block screw

C. Neutral wire (white or center wire)

D. 3/4.(1.9 cm) UL listed strain relief

E.Neutral ground wire

3. Connect ground wire (green or bare) of power supply cable to

external ground conductor screw. Tighten screw.

A B

io Ei[] •

F............J.........................

D .....

A. External ground conductor screw

B. Center silver-colored terminal block screw

C. Neutral wire (white or center wire)

D. s_,, (1.9 cm) UL listed strain relief

E.Ground wire (green or bare) of power supply cable

R Neutral ground wire

4. Place the hooked ends of the other power supply cable wires

under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!! !!

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

7. You have completed your electrical connections. Now go to

"Venting Requirements."

3-wire connection: Power Supply Cord

Use where local codes permit connecting cabinet-ground

conductor to neutral wire:

B D E

, i

C G F

A. 3-wire receptacle (NEMA type 10-30R)

B. 3-wire plug

C. Neutral prong

D. Spade terminals with up turned ends

E. _" (1.9 cm) UL listed strain relief

F. Ring terminals

G. Neutral (white or center wire)

1. Loosen or remove center silver-colored terminal block screw.

Connect neutral wire (white or center wire) of power supply

cord to the center, silver-colored terminal screw of the terminal

block. Tighten screw.

B C

A. Neutralground wire

B. Externalground conductor screw

C. Center silver-colored terminal block screw

D. Neutral wire (whiteor center wire)

E. _" (1.9 cm)UL Iisted strain relief

3. Connect the other wires to outer terminal block screws.

Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

6. You have completed your electrical connections. Now go to

"Venting Requirements."

3-wire connection: Direct Wire

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed.

Strip 31/2'' (8.9 cm) of outer covering from end of cable. Strip

insulation back 1" (2.5 cm). Ifusing 3-wire cable with ground wire,

cut bare wire even with outer covering. Bend ends of wires into a

hook shape.

When connecting to the terminal block, place the hooked end of

the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw, as shown.

1. Loosen or remove center silver-colored terminal block screw.

Place the hooked end of the neutral wire (white or center wire)

of power supply cable under the center screw of terminal

block (hook facing right). Squeeze hooked end together.

Tighten screw.

B C

Optional 3-wire connection

Use for direct wire or power supply cord where local codes do

not permit connecting cabinet-ground conductor to neutral

wire.

1. Remove center silver-colored terminal block screw.

2. Remove neutral ground wire from external ground conductor

screw. Connect neutral ground wire and the neutral wire (white

or center wire) of power supply cord/cable under center,

silver-colored terminal block screw. Tighten screw.

A B C

A. Neutral ground wire

B. External ground conductor screw

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. _" (1.9 cm) UL listed strain relief

Place the hooked ends of the other power supply cable wires

under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!! !!

4. Tighten strain relief screw.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

6. You have completed your electrical connections. Now go to

"Venting Requirements."

A. External ground conductor screw

B. Neutral ground wire

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. %" (1.9 cm) UL listed strain relief

E Grounding path determined by a qualified electrician

Connect the other wires to outer terminal block screws.

Tighten screws.

!! !!

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

6. Connect a separate copper ground wire from the external

ground conductor screw to an adequate ground.

• Removeexcessflexiblemetalventtoavoidsaggingand

kinkingthatmayresultinreducedairflowandpoor

performance,

• Donotinstallflexiblemetalventinenclosedwalls,ceilingsor

floors.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

Elbows

45° elbows provide better airflow than 90° elbows.

Good Better

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure

exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible

heavy metal vent.

• Review Vent system chart. Modify existing vent system if

necessary to achieve the best drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be

used. DURASAFF Mventing products are recommended.

4" (10.2cm) heavymetal exhaust vent

DURASAFE TM vent products can be purchased from your

dealer or by calling the toll-free number listed on the cover of

the Dryer User Instructions. For more information, see the

"Assistance or Service" section of the Dryer User Instructions.

Rigid metal vent

• For best drying performance, rigid metal vents are

recommended.

• Rigid metal vent is recommended to avoid crushing and

kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for

cleaning.

• Flexible metal vent must be fully extended and supported

when the dryer is in its final location.

Clamps

• Use clamps to seal all joints.

• Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

(10.2 cm)

A. Louvered hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

4-"

(10.2 cm)_C _

I_ 21/2.

(6.4cm)

An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground

or any object that may be in the path of the exhaust (such as

flowers, rocks or bushes, snow line, etc.).

Do not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

NOTE: The following kits for close clearance alternate installations

Choose your exhaust installation type are available for purchase. Please see the "Assistance or Service"

section of the Dryer User Instructions.

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer, Other

installations are possible,

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

E. Clamps

F. Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

Standard exhaust installation with rigid metal or flexible

metal vent

• Over-the-Top Installation:

Part Number 4396028

Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for

your installation, Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

A. Over-the-top installation (also available

with one offset elbow)

B. Periscope installation

Determine vent path

• Select the route that will provide the straightest and most

direct path outdoors.

• Plan the installation to use the fewest number of elbows and

turns,

• When using elbows or making turns, allow as much room as

possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 °turns possible,

Determine vent length and elbows needed for best

drying performance

• Use the Vent system chart below to determine type of vent

material and hood combinations acceptable to use,

NOTE: Do not use vent runs longer than those specified in the

Vent system chart. Exhaust systems longer than those

specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will help

to achieve the best drying performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add one

90° turn to the chart.

Number of Type of Box or Angled

90° turns vent Iouvered hoods

or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft (8.5 m)

Check the levelness of the dryer. Check levelness first

side to side, then front to back.

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ft (7 m) 15 ft (4.6 m)

Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

Connect vent to exhaust hood, Vent must fit inside exhaust

hood, Secure vent to exhaust hood with 4" (10.2 cm) clamp,

Run vent to dryer location. Use the straightest path possible.

See "Determine vent path" in "Plan Vent System." Avoid 90°

turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior

of the vent to secure vent.

If the dryer is not level, prop up the dryer using a wood block. Use

a wrench to adjust the legs up or down and check again for

levelness.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Check that the vent is secured

to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible

gas line.

4. Once the exhaust vent connection is made, remove the corner

posts and cardboard.

You can change your door swing from a right-side opening to a

left-side opening, if desired.

Reversible Large Side-Swing Door

ss(/s Leve L®gs"

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. To protect the floor, use a large, flat piece of cardboard from

the dryer carton. Place cardboard under the entire back side

of the dryer.

2. Firmly grasp the body of the dryer (not the top or console

panel). Gently lay the dryer on the cardboard. See illustration.

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent.

1. Place towel (A) on top of dryer to protect surface.

2. Open dryer door. Remove bottom screws from cabinet side of

hinges (C). Loosen (do not remove) top screws from cabinet

side of hinges.

3. Lift door until top screws in cabinet are in large part of hinge

slot. Pull door forward off screws. Set door on top of dryer.

Remove top screws from cabinet.

4. Use a small, flat-blade screwdriver to gently remove

4 hinge hole plugs (D) on left side of cabinet. Insert plugs into

hinge holes on right-hand side of cabinet,

5. Insert screws into bottom holes on left side of cabinet. Tighten

screws halfway. Position door so large end of door hinge slot

is over screws. Slide door up so screws are in bottom of slots.

Tighten screws. Insert and tighten top screws in hinges.

6. Close door and check that door strike aligns with door catch

(B). If needed, slide door catch left or right within slot to adjust

alignment.

Reversible Super Wide Side-Swing Door

1. Place towel (A) on top of dryer to protect surface.

2. Open dryer door. Remove bottom screws from cabinet side of

hinges (D). Loosen (do not remove) top screws from cabinet

side of hinges.

3. Lift door until top screws in cabinet are in large part of hinge

slot. Pull door forward off screws. Set door (handle side up) on

top of dryer. Remove top screws from cabinet.

4. Remove screws attaching hinges to door.

5. Remove screws at top, bottom and side of door (4 screws).

Holding door over towel on dryer, grasp sides of outer door

and gently lift to separate it from inner door. Do not pry apart

with putty knife. Do not pull on door seal or plastic door

catches.

6. Be certain to keep cardboard spacer centered between doors.

Reattach outer door panel to inner door panel so handle is on

the side where hinges were just removed.

7. Attach door hinges to dryer door so that the larger hole is at

the bottom of the hinge.

8. Remove door strike (E)from cabinet. Use a small, flat-blade

screwdriver to gently remove 4 hinge hole plugs (F) on left side

of cabinet. Insert plugs into hinge holes on right side of

cabinet.

Insert screws into bottom holes on left side of cabinet. Tighten

screws halfway. Position door so large end of door hinge slot

is over screws. Slide door up so screws are in bottom of slots.

Tighten screws. Insert and tighten top screws in hinges.

10. Remove door strike plug (B). Insert the door strike you

removed in Step 8 into hole and secure with screw. Insert door

strike plug into original door strike hole and secure with screw.

11. Close door and check that door strike aligns with door catch

(C). Ifit is needed, slide door catch left or right within slot to

adjust alignment.

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer's final location. Be sure the vent is not

crushed or kinked.

5. Check that the dryer is level. See "Level Dryer."

6. In the U.S.A.

• For power supply cord installation, plug into an outlet. For

direct wire installation, turn on power.

In Canada

10.

• Plug into a grounded 4 prong outlet. Turn on power.

Remove the blue protective film on the console and any tape

remaining on the dryer.

Read "Dryer Use" in the Dryer User Instructions.

Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

Set the dryer on a full heat cycle (not an air cycle) for

20 minutes and start the dryer.

If the dryer will not start, check the following:

• Controls are set in a running or "On" position.

• Start button has been pushed firmly.

• Dryer is plugged into an outlet and/or electrical supply

is on.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the

dryer door and feel for heat. If you feel heat, cancel cycle and

close the door.

If you do not feel heat, turn off the dryer and check the

following:

• There may be 2 household fuses or circuit breakers for the

dryer. Check that both fuses are intact and tight, or that

both circuit breakers have not tripped. If there is still no

heat, contact a qualified technician.

NOTE: You may notice a burning odor when the dryer is first

heated. This odor is common when the heating element is first

used. The odor will go away.

INSTRUCCIONES DEINSTALACION PARA LA SECADORA

ELI CTRICA DE29" (73,7 CM)

SEGURIDAD DELASECADORA

Su seguridad y la seguridad de los demos es muy importante.

Hemos incluido muchos mensajes importantes de seguridad en este manual yen su electrodomestico. Lea y obedezca siempre

todos los mensajes de seguridad.

Este es el sfmbolo de advertencia de seguridad.

Este sfmbolo le llama la atenci6n sobre peligros potenciales que pueden ocasionar la muerte o una lesi6n a

usted y a los demos.

Todos los mensajes de seguridad iran a continuacidn del simbolo de advertencia de seguridad y de la palabra

"PELIGRO" o "ADVERTENClA". Estas palabras significan:

Si no eigue las instrucciones de inmediato, usted puede

morir o sufrir una lesion grave.

Si no eigue las instrucciones, usted puede morir o eufrir

una lesion grave.

Todos los mensajes de seguridad le diran el peligro potencial, le dir_.n c6mo reducir las posibilidades de sufrir una lesi6n y Io que

puede suceder si no se siguen las instrucciones.

INSTRUCCIONESDE INSTALACION

Re_na las herramientas y piezas necesarias antes de comenzar la

instalaci6n. Lea y siga las instrucciones provistas con cualquiera

de las herramientas enlistadas aqui.

Las instalaciones en casas rodantes requieren herramientas del

sistema de escape de metal, que se encuentran disponibles para

ser compradas en el distribuidor donde compr6 la secadora. Para

obtener mas informaci6n, tome como referencia la secci6n

"Ayuda o servicio tecnico" de sus Instrucciones para el usuario de

la secadora.

• Destornillador de cuchilla •

plana

• Destornillador Phillips # 2

• Llavedetuercasajustable •

que se abra a 1" (2,5 cm) •

o una Ilave de cube de

cabeza hexagonal (para •

regular las patas de la

secadora)

• Desforrador de alambre •

(instalaciones de

cableado directo)

Tijeras de lata

(instalaciones del nuevo

ducto de escape)

Nivel

Abrazaderas para ducto

Pistola y masilla para

calafateo (para instalar el

nuevo ducto de escape)

Cinta para medir

Piezas suministradas:

Retire el paquete de piezas del tambor de la secadora. Verifique

que esten todas las piezas.

4patas niveladoras

Piezas necesarias:

Verifique los c6digos locales. Verifique el suministro electrico

existente y la ventilaci6n y yea "Requisites electricos" y

"Requisitos de ventilaci6n" antes de comprar las piezas.

Peligro de Explosion

Mantenga los materiales y vapores inflamables, como

la gasolina, lejos de la secadora.

Coloque la secadora a un rninimo de 46 cm sobre

el piso para la instalaci6n en un garaje.

No seguir estas instrucciones puede ocasionar

la muerte, explosi6n o incendio.

Usted necesitar&

• Una ubicaci6n que permita una instalaci6n adecuada del

ducto de escape. Consulte "Requisites de ventilaci6n".

• Un circuito separado de 30 amperios.

Siesta usando un cable de suministro de energ[a, un contacto

con conexi6n a tierra ubicado a unos 2 pies (61 cm) de

cualquiera de los lades de la secadora. Vea "Requisitos

electricos".

Un piso resistente para soportar la secadora con un peso total

(secadora y carga) de 200 Ibs (90,7 kg). Tambien se debe

considerar espacio adicional para otroelectrodomestico que

le acompaSe.

Un piso nivelado con un declive maximo de 1" (2,5 cm) debajo

de la secadora completa. (Si el declive es mayor que 1" [2,5

cm], instale el Juego de extensi6n de patas de la secadora,

Pieza No. 279810.) La ropa quizas no rote adecuadamente y

los modelos con ciclos del sensor automatico posiblemente

no funcionen debidamente si la secadora no esta nivelada.

No ponga afuncionar su secadora a temperaturas inferiores a

45°F (7°C). A temperaturas inferiores, es posible que la secadora

no se apague al final de un ciclo automatico. Los tiempos de

secado pueden prolongarse.

No debe instalarse ni guardarse la secadora en un Area en donde

pueda estar expuesta al agua y/o a la intemperie.

Verifique los requisites de los c6digos. Algunos c6digos limitan, o

no permiten, la instalaci6n de la secadora en garajes, cl6sets,

casas rodantes o en dormitorios. P6ngase en contacto con el

inspector de construcciones de su Iocalidad.

Espacios para la instalaci6n

La ubicaci6n debe ser Io suficientemente grande para poder abrir

completamente la puerta de la secadora.

Dimensiones de la secadora

223A ''

_(57,8cm)

13¾"

4,9cm)

A. Puerta chica de apertura lateral

B. Puerta grande de apertura lateral

C. Puerta ancha de apertura lateral

D. Puerta ancha de apertura vertical

*La mayor[a de las instalaciones requieren un espacio mfnimo de

5" (12.7 cm) detras de la secadora para acomodar el ducto de

escape con code. Vea "Requisites de ventilaci6n".

Espacio para la instalacibn en un lugar empotrado o en un

clbset

Se recomiendan las siguientes medidas de espacio para esta

secadora. Esta secadora ha sido puesta a prueba para espacios

de 0" (0 cm) en los costados yen la parte posterior. El espacio

recomendado debe ser considerado pot los siguientes motives:

• Debe considerarse el espacio adicional para facilitar la

instalaci6n y el servicio tecnico.

• Se podrian necesitar espacios libres adicionales para las

molduras de la pared, puerta y piso.

• Se debe considerar agregar espacio adicional en todos los

lados de la secadora para reducir la transferencia de ruido.

• Para la instalaci6n en cl6set, con una puerta, se requieren

aberturas de ventilaci6n mfnimas en la parte superior e inferior

de la puerta. Se aceptan puertas tipo persianas con aberturas

de ventilaci6n equivalentes.

• Tambi_n se debe considerar espacio adicional para otro

electrodomestico que le acompaSe.

j o- -oH

[-] I_ I;_b,0cm) 48pulg.2*_

L_l

{310cm2)

18"*

(45,7c1 ___ [_ 24pulg.2.-

.__ ._ (155cm2)

_"-_ _29" _t _-_" _1"*1_2_J,"_15"*

(2,5cm) (73,66crn) (2,5cm) (2,5cm) (70,5cm) {12,7crn)

A B

_3"*

{7,6cm)

NNI-

(7,6ora)

A. Lugar empotrado

B. Vista lateral - cldset o lugar confinado

C. Puerta del cldset con oriflcios de ventilacidn

*Espacio necesario

Requisitos de instalacibn adicionales para las casas

rodantes

Esta secadora es apropiada para instalaciones en casas

rodantes. La instalaci6n debe ajustarse al Estandar de seguridad

y construcci6n de casas fabricadas, Titulo 24 CFR, Parte 3280

(anteriormente conocido como Estandar federal para la seguridad

y construcci6n de casas rodantes, Tftulo 24, HUD Parte 280).

Las instalaciones en casas rodantes necesitan:

• Herramientas del sistema de escape de metal, que se

encuentran disponibles para ser compradas en su

distribuidor.

Se deben tomar medidas especiales en el caso de casas

rodantes para introducir el aire del exterior en la secadora. La

abertura (como la de una ventana adyacente) debera ser per

Io menos el doble de tamaSo que la abertura de ventilaci6n de

la secadora.

Usted es responsable de

• Ponerseen contacto con un instalador electrico calificado.

Asegurarse de que la conexi6n electrica sea adecuada y de

conformidad con el C6digo Nacional Electrico, ANSl/NFPA

70 - 01tima edici6n y con todos los c6digos y ordenanzas

locales.

El C6digo Nacional Electrico requiere una conexi6n de

suministro electrico de 4 hilos para aquellos hogares

construidos despues de 1996, para los circuitos de secadora

que se hayan reformado despues de 1996 y todas las

instalaciones de casas rodantes.

Usted puede obtener una copia de todas las normas arriba

indicadas en:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

Proveer el suministro electrico requerido de 3 6 4 alambres,

monofasico, de 120/240 voltios, 60 Hz, CA solamente (o un

suministro electrico de 3 6 4 alambres, de 120/208 voltios, si

se especifica en la placa indicadora de corriente/de la serie)

en un circuito separado de 30 amperios, protegido con

fusibles en ambos lados de la Ifnea. Se recomienda un fusible

retardador o un cortacircuitos. Conectela a un circuito

derivado individual. No tenga un fusible en el circuito neutro o

de conexi6n a tierra.

[] No use un cable electrico de extensi6n.

Si los c6digos Io permiten y se emplea un alambre de

conexi6n a tierra separado, es recomendable que un

electricista calificado determine si la trayectoria de conexi6n a

tierra es adecuada.

Conexibn el_ctrica

Para instalar su secadora adecuadamente, usted debe determinar

el tipo de conexi6n electrica que va a usar y seguir las

instrucciones que aquf se proveen para el caso.

[] Si los c6digos locales no permiten la conexi6n de un

conductor para conexi6n atierra del equipo al alambre neutro,

vea la secci6n "Conexi6n opcional de 3 hilos".

[] Esta secadora ha side manufacturada lista para set instalada

en una conexi6n de suministro de energ[a electrica de 3 hilos.

El hilo neutro de puesta a tierra esta permanentemente

conectado al conductor neutral (cable blanco) dentro de la

secadora. Si la secadora esta instalada con una conexi6n de

suministro electrico de 4 hilos, el hilo neutro de puesta a tierra

se debe quitar del tornillo de puesta a tierra exterior (tornillo

verde) y ajustar debajo del terminal neutral (cable central o

blanco) del bloque de terminal. Cuando el hilo neutro de

puesta a tierra este ajustado debajo del terminal neutral (cable

central o blanco) del bloque de terminal, el gabinete de la

secadora queda aislado del conductor neutral.

[] Debera usarse una conexi6n con suministro de energ[a de

4 hilos cuando el aparato este instalado en una ubicaci6n en

la cual este prohibida la conexi6n a tierra a traves del

conductor neutro. Esta prohibido hacer la puesta a tierra a

traves del conductor neutro para (1) las nuevas instalaciones

de circuito derivado, (2) casas rodantes, (3) vehiculos de

recreaci6n y (4) Areas donde los c6digos locales prohiben la

conexi6n a tierra atraves de conductores neutros.

Si emplea un cable de suministro el_ctrico:

Use un juego aprobado de UL para cable de suministro electrico

que este marcado para ser usado en secadoras de ropa. El juego

debera contener:

[] Un cable de suministro electrico de 30 amperios aprobado de

UL, con 120/240 voltios minimo. El cable debera ser del tipo

SRD o SRDT y debera tener un largo de por Io menos 4 pies

(1,22 m). Los hilos que conectan con la secadora deberan

terminar en terminales de anillo o de horquilla con los

extremes hacia arriba.

[] Un protector de cables aprobado de UL.

Si el contacto de pared luce como _ste:

Contacto de 4 alambres (!4-30R)

Entonces elija un cable de suministro electrico de 4 alambres con

terminales de anillo o de horquilla y con protector de cables

aprobado de UL. El cable de suministro electrico de 4 hilos, de

per Io menos 4 pies (1,22 m) de largo, debera tener 4 hilos de

cobre de calibre 10 y coincidir con un receptaculo de 4 hilos tipo

NEMA 14-30R. El hilo de conexi6n a tierra (conductor a tierra)

puede set verde o desnudo. El conductor neutro debe ser

identificado con una cubierta blanca.

Si el contacto de pared luce como _ste:

Contacto de 3 alambres (10-30R)

Entonces elija un cable de suministro electrico de 3 alambres con

terminales de anillo o de horquilla y con protector de cables

aprobado de UL El cable de suministro electrico de 3 hilos, de

por Io menos 4 pies (1,22 m) de largo, debera tener 3 hilos de

cobre de calibre 10 y coincidir con un receptaculo de 3 hilos tipo

NEMA 10-30R.

Si hace la conexi6n con cableado directo:

El cable de suministro electrico debe set igual al suministro

electrico (de 4 alambres o de 3 alambres) y debe ser:

[] Cable blindado flexible o cable de cobre forrado no metalico

(con alambre de puesto a tierra), protegido con un conducto

metalico flexible. Todos los alambres conductores de

corriente deben estar aislados.

[] Alambre de cobre s61ido de calibre 10 (no utilice aluminio).

[] Pot Io menos 5 pies (1,52 m) de largo.

INSTRUCCIONES PARA LA CONEXION A TIERRA

[] Para la conexi6n de una secadora mediante cable

electrico conectado a tierra:

Esta secadora debe estar conectada a tierra. En el caso de

funcionamiento defectuoso o averia, la conexion a tierra

reducira el riesgo de choque electrico al proporcionar una

vfa de menor resistencia para la corriente electrica. Esta

secadora usa un cable que cuenta con un conductor para la

conexi6n a tierra del equipo y un enchufe de conexi6n a

tierra. El enchufe debe conectarse en un contacto

apropiado, que este debidamente instalado y conectado a

tierra de acuerdo con todos los codigos y ordenanzas

locales.

[] Para la conexi6n permanente de una secadora:

Esta secadora debe estar conectada a un sistema de

cableado de metal permanente, conectado a tierra, o se

debe tender un conducto para la conexion a tierra del

equipo con los conductores de circuito y conectado al

terminal de tierra del equipo o al conductor de suministro de

la secadora.

ADVERTENCIA: La conexi6n indebida del

conductor para la conexi6n a tierra del equipo puede

ecasionar un riesgo de choque electrico. Verifique con un

electricista, representante e personal de servicio tecnico

calificado para asegurarse de que la conexion a tierra de la

secadora sea aprepiada. No modifique el enchufe que viene

con el cable electrico. Si no encaja en el contacto, contrate

un electricista calificado para que instale un contacto

adecuado.

GUARDE ESTAS INSTRUCCIONES

Cable de suministro el_ctrico

Peligro de Incendio

Use un cable de suministro electrico nuevo de

30 amperes que este en la lista de UL

Use un protector de cables que este en la lista de UL.

Desconecte el suministro electrico antes de hacer las

cone×Jones electricas.

Conecte el alambre neutro (el blanco o el del centro)

ai terminal central (plateada).

El alambre de tierra (el verde o el no aislado) se debe

conectar con el conector verde de tierra.

Conecte los 2 alambres de suministro restantes con

las 2 terminales restantes (las doradas).

Apriete firmemente todas ias conexiones ei_ctricas.

No seguir estas instrucciones puede ocasionar ia

muerte, incendio, o choque eiectrico.

Cable directo

Peiigro de Incendio

Utiiice aiambres de cobre sbiido de ancho 10.

Use un protector de cables que este en ia iista de UL.

Desconecte ei suministro eiectrico antes de hacer las

conexiones electricas.

Conecte el alambre neutro (el bianco o ei dei centro)

al terminal central (piateada).

Ei aiambre de tierra (el verde o el no aisiado) se debe

conectar con ei conector verde de tierra.

Conecte los 2 alambres de suministro restantes con

las 2 terminales restantes (las doradas).

Apriete firmemente todas ias conexiones eiectricas.

No seguir estas instrucciones puede causar ia muerte,

incendio o choque electrico.

1. Desconecte el suministro de energfa.

2. Quite el tornillo de sujeci6n y la cubierta del bloque de

terminal.

A B C D

A. Cubierta del bloque de terminal

B. Tomillo conductor a tierra externo

C. Tomillo del bloque de terminal de color plateado, del centre

D. Ubicacidn del tomillo de sujecidn

E. Alambre de conexidn a tierra neutro

3. Instale el protector de cables.

Estilo 1: Protector de cables del cable de suministro de

energia

• Quite los tornillos de un protector de cables de

3/4"(1,9 cm) que este en la lista de UL (con la marca UL en

el protector de cables). Coloque las lengQetas de las dos

secciones de la abrazadera en el orificio que esta debajo

de la abertura del bloque de terminal de manera que una

lengQeta este apuntando hacia arriba y la otra este

apuntando hacia abajo, y sujetelas en su lugar. Apriete los

tornillos del protector de cables Io suficiente para

mantener las dos secciones de la abrazadera juntas.

A. LengQeta del protector de cables

apuntando hacia arriba

B. Ofiflcio debajo de la abertura del

bloque de terminal

C. Seccidn de la abrazadera

D. LengQeta del protector de cables

apuntando hacia abajo

F. Ofificio debajo de la abertura del bloque de terminal

Haga pasar el cable de suministro de energ[a a traves del

protector de cables. AsegQrese de que el aislamiento de

cables del cable de suministro de energia este dentro del

protector de cables. El protector de cables debera encajar

bien con el gabinete de la secadora y estar en posici6n

horizontal. No ajuste mas los tornillos del protector de

cables en este momento.

Estilo 2: Protector de cables para cable directo

• Desatornille el conector de conducto removible y

cualquier tornillo del protector de cables de %" (1,9 cm)

que este en la lista de UL (con la marca UL en el protector

de cables). Haga pasar la secci6n roscada del protector

de cables a traves del orificio que esta debajo de la

abertura del bloque de terminal. Busque dentro de la

abertura del bloque de terminal y atornille el conector de

conducto removible sobre las roscas del protector de

cables.

A. Conector del conducto removible

B. Orificio debajo de la abertura del

bloque de terminal

C. Roscas del protector de cables

Haga pasar el cable directo a traves del protector de

cables. El protector de cables debera encajar bien con el

gabinete de la secadora y estar en posici6n horizontal.

Apriete el tornillo del protector de cables contra el cable

directo.

Ahora termine la instalaci6n siguiendo las instrucciones para

el tipo de su conexidn electrica:

Alambre de 4 hilos (se recomienda)

Alambre de 3 hilos (si no dispone de alambre de 4 hilos)

Opciones para la conexi6n el_ctrica

Si su casa tiene: Y usted va a Vaya a la secci6n

conectar con:

Un contacto de 4 Un cable de Conexi6n de

hilos (Tipo NEMA suministro 4 hilos:

14-30R) electrico para Cable de

secadora, suministro

aprobado de electrico

UL, de 120/240

voltios minimo y

30 amperios*

Cable directo de Un Conexi6n de

4 hilos desconectador 4 hilos:

con fusible o Cable directo

una caja

(12,7 Cm) disyuntor*

Contacto de 3 hilos Un cable de Conexi6n de

(Tipo NEMA 10-30R) suministro 3 hilos:

(_ electrico para Cable de

secadora, suministro

aprobado de electrico

UL, de 120/240

voltios minimo y

30 amperios*

Cable directo de Un Conexi6n de

3 hilos desconectador 3 hilos:

con fusible o Cable directo

una caja de

disyuntor*

*Si los c6digos locales no permiten la conexi6n de un conductor

de conexi6n a tierra del gabinete al cable neutro, prosiga a la

secci6n "Conexi6n opcional de 3 hilos'.

Conexibn de 4 hilos: Cable de suministro el_ctrico

IMPORTANTE: Se necesita una conexi6n de alambre de 4 hilos

para las casas rodantes y para los casos en que los c6digos

locales no permitan el use de conexiones de 3 hilos.

B F

C D E G

A. Contacto de 4 hilos (ripe NEMA 14-30R)

B. Enchufe de 4 terminales

C. Terminal de conexidn a tierra

D. Terminal de conexidn a neutro

E. Terminales de horquilla con los extremos hacia arriba

F. Protector de cables aprobado de UL, de 3/4"(!,9 cm)

G. Terminales anulares

1. Saque el tornillo central del bloque de terminal.

Saque el hilo de tierra neutro del aparato del tornillo

conductor de tierra extemo, Conecte el hilo neutro de puesta

a tierra y el hilo neutro (hilo blanco o central) del cable de

suministro de energ[a debajo del tornillo central de color

plateado del bloque de terminal. Apriete el tornillo.

A. Tornillo conductor de tierra externo - La Ifnea punteada ilustra

la posicidn del hilo de tierra NEUTRO antes de moverlo al

tornillo central de color plateado del bloque de terminal.

B. Tornillo central de color plateado del bloque de terminal

C. Hilo neutro (hilo blanco 0 central)

D. Protector de cables de 3/4"(1,9 cm), que est_ en la lista de UL

E.Hilo neutro de puesta a tierra

Conecte el hilo de tierra (verde o desnudo) del cable de

suministro el@ctrico al tornillo conductor de tierra externo.

Apriete el tornillo.

A B C

A. Tomillo conductor de tierra externo

B. Tomillo central de color plateado del bloque de terminal

C. Hilo neutro (hilo blanco 0 central)

D. Protector de cables de 3/4"(1,9 cm), que est_ en la lista de UL

E.Hilo de tierra (verde 0 desnudo) del cable de suministro de energfa

F Hilo neutro de puesta a tierra

Conecte los otros hilos a los tornillos exteriores del bloque de

terminal. Apriete los tornillos,

5. Apriete los tornillos del protector de cables.

6. Introduzca la lengOeta de la cubierta del bloque de terminal en

la ranura del panel posterior de la secadora. Asegure la

cubierta con el tornillo de sujeci6n.

7. Usted ha completado la conexi6n el@ctrica, Ahora vaya a

"Requisitos de ventilaci6n".

Conexi6n de 4 hilos: Cable directo

IMPORTANTE: Se necesita una conexi6n de alambre de 4 hilos

para las casas rodantes y para los casos en que los c6digos

locales no permitan el uso de conexiones de 3 hilos.

El cable de conexi6n directa debe tenet 5 pies (1,52 m) extra de

largo para poder mover la secadora si fuese necesario.

Pele 5" (12,7 cm) de la cubierta exterior desde el extremo del

cable, dejando el hilo de tierra desnudo a 5" (12,7 cm). Corte

11/2'' (3,8 cm) de los 3 hilos restantes. Pele el aislamiento

1" (2,5 cm) hacia atras. Doble los extremos de los hilos para

formar un gancho.

AI conectar el hilo al bloque de terminal, coloque el extremo del

hilo en forma de gancho debajo del tornillo del bloque de terminal

(con el gancho mirando hacia la derecha). Apriete y junte el

extremo en forma de gancho y apriete el tornillo. Vea el ejemplo a

continuaci6n.

Saque el tornillo central de color plateado del bloque de

terminal.

Saque el hilo de tierra neutro del tornillo conductor de tierra

externo. Conecte el hilo neutro de puesta a tierra y coloque el

extremo en forma de gancho (gancho mirando hacia la

derecha) del hilo neutro (blanco o central) del cable de

conexi6n directa debajo del tornillo central del bloque de

terminal. Apriete y junte los extremos en forma de gancho.

Apriete el tornillo.

A B

........C

/,/'

A. Ternillo conductor de tierra externo - La Ifnea punteada

ilustra la posicidn del hilo de tierra NEUTRO antes de

moverlo al tomillo central del bloque de terminaL

B. Tomillo central de color plateado del bloque de terminal

C. Hilo neutro (hilo blanco o central)

D. Protecter de cables de 3_,,(1,9 cm), que est_ en la Iista de UL

E. Hilo neutro de puesta a tierra

Conecte el hilo de tierra (verde o desnudo) del cable de

suministro electrico al tornillo del conductor de tierra externo.

Apriete el tornillo.

A B

[ []

F E .............

Conecte el hilo neutro (hilo blanco o central) del cable de

suministro electrico al tornillo central de color plateado del

bloque de terminal. Apriete el tornillo.

B C

A. Tornillo conductor de tierra externo

B. Tornillo central de color plateado del bloque de terminal

C. Hilo neutro (hilo blanco 0 central)

D. Protector de cables de 3/4,,(1,9 cm), que est_ en la lista de UL

E.Hilo de tierra (verde o desnudo) del cable de suministro de energfa

FHilo neutro de puesta a tierra

Coloque los extremos en forma de gancho de los otros hilos

del cable de suministro electrico debajo de los tornillos

exteriores del bloque de terminal (con los ganchos mirando

hacia la derecha). Apriete y junte los extremes enganchados.

Apriete los tornillos.

!! !!

5. Apriete los tornillos del protector de cables.

6. Introduzca la lengOeta de la cubierta del bloque de terminal en

la ranura del panel posterior de la secadora. Asegure la

cubierta con el tornillo de sujeci6n.

7. Usted ha completado la conexi6n electrica. Ahora vaya a

"Requisites de ventilaci6n".

Conexibn de 3 hilos: Cable de suministro el_ctrico

Use cuando los cbdigos locales permitan la conexi6n del

conductor de tierra del gabinete al hilo neutro:

B D E

C G F

A. Contacto de 3 hilos (NEMA tipo 10-30R)

B. Enchufe de 3 hflos

C. Terminal neutro

D. Terminales de horquilla con extremos hacia arriba

E. Protector de cables que est_ en la lista de UL de 3/4.(1,9 cm)

F. Terminales anulares

G. Neutro (hilo blanco o central)

1. Afloje o saque el tornillo central de color plateado del bloque

de terminal.

A. Hilo neutro de puesta a tierra

B. Tomillo conductor de tierra extemo

C. Tornillo central de color plateado del bloque de terminal

D. Hflo neutro (hilo blanco o central)

E. Protector de cables que est_ en la Iista de UL de 3/4"(!,9 cm)

3. Conecte los otros hilos a los tornillos exteriores del bloque de

terminal. Apriete los tornillos.

!! !!

4. Apriete los tornillos del protector de cables.

5. Introduzca la lengQeta de la cubierta del bloque de terminal en

la ranura del panel posterior de la secadora. Asegure la

cubierta con el tornillo de sujeci6n.

6. Usted ha completado la conexi6n electrica. Ahora vaya a

"Requisitos de ventilaci6n".

Conexibn de 3 hilos: Cable directo

Use cuando los c6digos locales permitan la conexibn del

conductor de tierra del gabinete al hilo neutro.

El cable de conexi6n directa debe tenet 5 pies (1,52 m) extra de

largo para poder mover la secadora si fuese necesario.

Pele 31/2'' (8,9 cm) de la cubierta exterior desde el extremo del

cable. Pele el aislamiento 1" (2,5 cm) hacia atras. Si usa un cable

trifilar con hilo de tierra, corte el hilo desnudo para que quede

nivelado con la cubierta exterior. Doble los extremos de los hilos

para formar un gancho.

La page est en cours de chargement...

Admiral YNED5800TQ0 Installation Instructions Manual

Marque: Admiral

Modèle: YNED5800TQ0

Catégorie: Sèche-linge électriques

Taper: Installation Instructions Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Admiral YNED5800TQ0
español: Admiral YNED5800TQ0

Documents connexes

Roper NED4500TQ0 Guide d'installation

Admiral YNED5800TQ0 Installation Instructions Manual

Admiral YNED5800TQ0 Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents