Makita Chainsaw DCS 400 Manuel utilisateur

Marque: Makita

Modèle: Chainsaw DCS 400

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Ce manuel convient également à

WARNING!

Read and understand this Manual. Always follow safety precautions in the Owner’s and Safety

Manual. Improper use can cause serious injury! Preserve this Manual carefully!

ATTENTION!

Suivez toujours les conseils de sécurité du présent manuel d’emploi et de sécurité. Une utilisation

incorrecte de la tronçonneuse peut entraîner des blessures graves! Conservez avec soin ce manuel.

Lisez et comprenez ce manuel.

Owner’s and

Safety Manual

for Gasoline Chain Saws (pages 2 - 30)

Manuel d’emploi

et de sécurité

de tronçonneuses thermiques (pages 31 - 59)

DCS 340

DCS 341

DCS 400

DCS 401

WARNING !

Careless or improper use of this product can cause serious or even fatal injury.

Before operating a chain saw or other MAKITA products it is important that you read, fully understand and

carefully follow the instructions outlined in this owners manual. Kickback may cause severe or fatal injury and

is one of many potential dangers in operating a chain saw. Kickback and other safety related precautions are

described in detail within this owners manual. Additional owners manuals are available from MAKITA USA,

INC.,14930-C Northam Street, La Mirada, CA 90638-5753, Telephone: (714) 522 80 88 and MAKITA CANADA

INC., 1950 Forbes Street, Whitby, Ontario, Canada, L1N 7B7, Telephone: (905) 571 22 00.

Contents Page

Delivery inventory 3

Symbols 3

Safety precautions 4-15

Denomination of components 16

Technical data 17

Approved bar and chain combinations 17

Mounting the guide bar, saw chain 18-19

Checking the chain tension 19

Safety chain brake 20

Fuel / Refuelling 20-21

Starting the engine 22

Stopping the engine 22

Checking the safety chain brake 23

Checking the chain lubrication 23

MAKITA DCS 340, DCS 341, DCS 400, DCS 401

Contents Page

Adjusting the carburetor 23

Working in winter 24

Sharpening the saw chain 24-25

Cleaning the guide bar 25

Cleaning the brake band and sprocket 26

Replacing the suction head 26

Replacing the saw chain 26

Replacing / cleaning the spark arrester screen 26

Cleaning the air filter 27

Replacing the spark plug 27

Instructions for periodic maintenance 28

Service, spare parts and guarantee 28-29

Troubleshooting 29

Extract from the spare parts list 30

The MAKITA DCS 340/341/400/401 will be delivered in a protective cardboard box to prevent transport damage.

Cardboard is a basic raw material and is consequently reuseable or suitable for recycling (waste paper recycling).

This product complies with: American National Standard Institute B 175.1-1991 chain saw safety standard.

Canadian Standards Association Z62.1-95 chain saw safety standard.

Z62.3-96 chain saw kickback standard.

With the purchase of this chain saw you have chosen a German quality product. Important instructions for the

assembly and operation of this saw are given in this manual. For your own safety, we ask you to read the accident

prevention instructions very carefully before putting your chain saw into operation, as incorrect handling can,

despite all precautions, lead to accidents. With a little care and attention you will have good service and lasting

satisfaction from this first-rate product. The following industrial property rights apply: GSM MR 11414, GBM

9212059, GBM 29616652.

RE Y

Delivery inventory

In case one of the parts listed should not be included in the

delivery inventory, please consult your sales agent.

On/Off (I/O) switch

Stop engine!

Press starting valve

Engine -manual start

Choke lever

Carburetor adjustment

Working in winter

Working in summer

STOP

speed

Kickback!

Chaine brake

Fuel and oil mixture

Chain oil fill/oil pump

First aid

Recycling

Read instruction manual

and follow the warning-

and safety precautions!

Particular care

and caution!

Forbidden!

Wear protective helmet,

eye and ear protection!

Wear protective

gloves!

No smoking!

No open fire!

RE Y

Symbols

You will notice the following symbols on the chain saw and in the instruction manual:

1. Chain saw

2. Guide bar

3. Saw chain

4. Chain protection cover

5. Assembly tool

6. Owner’s manual (not shown)

Further

symbols

see page 5.

Safety precautions for chain saw operators

While operating the chain saw please observe the

following rules:

a) Contact of the guide bar nose with any object

should be avoided.

b) Tip contact may cause the guide bar to move

suddenly upward and backward, which may

cause serious or fatal injury.

c) Always operate the chain saw with both hands.

WARNING!

Read and follow all safety precautions in the owner’s

manual. Failure to follow instructions could result

in serious injury.

WARNING!

This chain saw is capable of severe kickback that

could result in serious injury to the operator. Do not

operate this chain saw unless you have

extraordinary cutting needs and experience in and

special training for dealing with kickback. Chain

saws with significantly reduced kickback potential

are available.

WARNING!

Kickback may occur when the nose or tip of the

guide bar touches an object, or when the wood

closes in and pinches the saw chain in the cut. This

contact may abruptly stop the saw chain and in

some cases may cause a lightning fast reverse

reaction, kicking the guide bar up and back towards

the user, or push the guide bar back towards the

operator. Kickback may cause you to lose control

of the saw.

As a chain saw user, you can take several steps to

reduce the risk of a kickback and potential injury.

A. With a basic understanding of kickback, you

can reduce or eliminate the element of surprise.

It is a sudden surprise that contributes to

accidents.

B. Keep a good firm grip on the saw with both

hands, your right hand on the rear grip and

your left hand on the tubular handle, when the

engine is running. Use a firm grip with thumbs

and fingers encircling the chain saw handles.

A firm grip can neutralize kickback and help

you maintain control of the saw. Don’t let go!

C. Make sure that the area in which you are

cutting is free from obstructions. Do not let the

nose of the guide bar contact the log, branch,

or any other obstructions which could be hit

while you are operating the saw.

D. Do not overreach or cut above shoulder height.

E. Follow manufacturer’s sharpening and main-

tenance instructions for the saw chain.

F. Only use replacement bars and chains speci-

fied by the manufacturer or the equivalent.

Additional safety precautions

The following additional safety precautions should be

observed by all users of chain saws:

1. Do not operate a chain saw when you are fatigued.

2. Use safety footwear; snug-fitting clothing;

protective gloves; and eye, hearing, and head

protection devices.

3. Use caution when handling fuel. Move the chain

saw at least 10 feet (3 m) from the fueling point

before starting the engine.

4. Do not allow other persons to be near the chain

saw when starting or cutting with the chain saw.

Keep bystanders and animals out of the work

area.

5. Do not start cutting until you have a clear work

area, secure footing, and a planned retreat path

from the falling tree.

6. Keep all parts of your body away from the saw

chain when the engine is running.

7. Before you start the engine, make sure that the

saw chain is not contacting anything.

8. Carry the chain saw with the engine stopped, the

guide bar and saw chain to the rear, and the

muffler away from your body.

9. Do not operate a chain saw that is damaged, is

improperly adjusted, or is not completely and

securely assembled. Be sure that the saw chain

stops moving when the throttle control trigger is

released.

10. Shut off the engine before setting it down.

11. Use extreme caution when cutting small size

brush and saplings because slender material may

catch the saw chain and be whipped towardyou

or pull you off balance.

12. When cutting a limb that is under tension be alert

for springback so that you will not be struck when

the tension on the wood fibers is released.

13. Keep the handles dry, clean, and free of oil or fuel

mixture.

14. Operate the chain saw only in well-ventilated

areas.

15. Do not operate a chain saw in a tree unless you

have been specifically trained to do so.

16. All chain saw service, other than the items listed

in the owner’s manual maintenance instructions,

should be performed by MAKITA . (For example,

if improper tools are used to remove the flywheel

or if an improper tool is used to hold the flywheel

in order to remove the clutch structural damage to

the flywheel could occur and could subsequently

cause the flywheel to burst.)

17. When transporting your chain saw, use the chain

protection cover.

18. Low kickback bars and low kickback chains are

designed to reduce the risk of kickback injury.

Ask your MAKITA dealer about these devices.

General Safety Precautions

The use of any chain saw may be hazardous. At full

throttle chain speed can reach 45 mph (20 m/s). It is

important that you read; fully understand and observe

the following safety precautions and warnings. Read

the owner’s manual and the safety instructions

periodically.

WARNING !

Reactive forces, including kickback, can be dan-

gerous. Careless or improper use of any chain saw

may cause serious or fatal injury.

Have your DOLMAR dealer show you how to

operate your chain saw. Observe all applicable

local safety regulations, standards and ordinances.

WARNING!

Minors should never be allowed to use a chain saw.

Bystanders, especially children and animals should

not be allowed in the area where a chain saw is in

use (fig. 1).

Never let the saw run unattended.

Store it in a locked place away from children. Fill

the fuel tank to 7/8 th full (see storing the saw).

Do not lend your chain saw without this owner’s

manual. Be sure that anyone using your saw un-

derstands the information given.

Proper use of a chain saw involves

1. the operator

2. the saw

3. the use of the saw.

Discription of symbols used on chain

saws:

Z 62.1-95 and

Z 62.3-96

Class 1A

ANSI B175.1-1991

45M6

Compliance with

ANSI -Standards

Compliance with

CSA -Standards

Chain Saw listed in accordance with

American National Standard Safety

Specifications for Gasoline Powered

Chain Saws (ANSI B 175.1-1991).

WARNING !

Prolonged use of chain saws exposing the operator

to vibrations may produce Whitefinger disease

(Raynaud’s phenomenon). This phenomenon

reduces the hand’s ability to feel and regulate

temperature, produces numbness and burning

sensations and may cause nerve and circulation

damage and tissue necrosis.

All MAKITA saws are therefore provided with an

antivibration system which is essential for those

using chain saws on a regular or sustained basis.

Antivibration systems do not guarantee that you will

not sustain Whitefinger disesase, however, they

reduce this danger considerably. Nevertheless,

continual and regular users should observe their

hands and fingers and in case of any abnormal

symptoms, seek medical advice immediately.

The operator

Physical Condition

You must be in good physical condition and mental

health and not under the influence of any substance

(drugs, alcohol), which might impair vision, dexterity

or judgment.

Always use two hands when

operating the chain saw!

* The Computed Kickback Angle is a calculated value

from energies measured on a test bench.It is not the

angle of the guide bar moved upward in case of a

KICKBACK.

Reduced Kickback Bar and

Chain combination that has been

evaluated with the power head

to achieve kickback protection

(according to ANSI and CSA

standards).

XXX.YYY.ZZZ

Contact of the guide bar tip with

any object should be avoided!

Tip contact may cause the guide

bar to move suddenly upward

and backward, which may cause

serious injury!

max. CKA 45

MaximumComputed Kickback Angle

(CKA)* with using the chain brake when

using the recommended bar and chain

combinations

(In this example the CKA is 40°).

Maximum Computed Kickback Angle

(CKA)* without using the chain brake when

using the recommended bar and chain

combinations (In this example the CKA is 45°).

max. CKA 40

Good footing is most important in chain saw work.

Wear sturdy boots with nonslip soles. Steel-toed safety

boots are recommended.

Proper eye protection is a must. Non-fogging, vented

goggles and a face screen is recommended. Their use

reduces the risk of eye and facial injury.

Wear an approved safety hard hat to protect your

head. Chain saw noise may damage your hearing.

Always wear noise protection equipment (ear plugs or

ear muffs) to protect your hearing.

Continual and regular users should have their hearing

checked regularly.

The saw

Parts of the chain saw: illustrations and description of

parts see page 16.

WARNING !

Never modify a chain saw in any way. Only

attachments supplied by MAKITA or expressly

approved by MAKITA for use with the specific saw

are authorized.

WARNING !

Bow guide bars substantially increase the potential

for kickback and severe or fatal injury due to the

greater kickback zone of the bow design. Bow

guide bars are not recommended for use on

MAKITA chain saws nor are they approved by the

ANSI B 175.1-1991 chain saw safety standard.

The use of the saw

Transporting the chain saw

WARNING!

Always stop the engine before putting a chain saw

down or carrying it. Carrying a chain saw with the

engine running is extremely dangerous. Accidental

acceleration of the engine can cause the chain to

rotate.

Avoid touching the hot muffler.

By hand: When carrying your saw by hand, the

engine must be stopped and the saw must be in the

proper position.

The chain protection cover should be over the

chain and the guide bar must point backwards.

When carrying your saw the bar should be behind

you (fig. 4).

By vehicle: When transporting in a vehicle, keep

chain and bar covered with the chain guard.

Properly secure your saw to prevent turnover, fuel

spillage and damage to the saw. Make sure the

saw is not exposed to heat or sparks.

Proper clothing

Clothing must be sturdy and snug-fitting, but allow

complete freedom of movement. Avoid loose-fitting

jackets, scarfs, neckties, jewelry, flared or cuffed pants,

or anything that could become entangled with the saw

or brush. Wear overalls or jeans with a reinforced

cutting resistant insert (fig. 3).

Protect your hands with gloves when handling saw

and saw chain. Heavy-duty, nonslip gloves improve

your grip and protect your hands.

Wear protective helmet,

eye and ear protection

Chain saw operating instructions

For assembly follow the procedure in the appropriate

section "Mounting Guide Bar and Chain" of this manual.

MAKITA chain, guide bar and sprocket must match

each other (see the appropriate section in this manual).

WARNING!

Proper tension of the chain is extremely important.

In order to avoid false setting the tensioning

procedure must be followed as described in this

manual. Always make sure the hexagonal nut(s)

for the sprocket guard is (are) tightened securely

after tensioning the chain. Check chain tension

once more after having tightened the nuts and

thereafter at regular intervals (always before starting

to work). If the chain becomes loose while cutting,

shut off the engine and then tighten. Never try to

tighten the chain while the engine is running!

Fueling

Your MAKITA saw uses on oil-gasoline mixture for fuel

(see chapter "Fuel" of this manual).

Wipe off any spilled fuel before starting your saw and

check for leakage.

Check for fuel leakage while refueling and during

operation. If fuel or oil leakage is found, do not start or

run the engine until leak is fixed and spilled fuel has

been wiped away. Clothing with fuel on it has to be

changed immediately (this is a danger to your life!).

Avoid skin contact with fuel. Never loosen or remove

the cap of the fuel tank while the engine is running.

Starting

Do not drop start. This method is very dangerous be-

cause you may lose control of the saw (fig. 6).

WARNING!

Gasoline is an extremely flammable fuel. Use

extreme caution when handling gasoline or fuel

mix. Do not smoke or bring any sparks or flame

near the fuel (fig. 5).

Fueling instructions

Fuel your chain saw in well ventilated areas or out-

doors. Always shut off the engine and allow it to cool

before refueling. Select bare ground for fueling and

move the chain saw at least 10 feet (3 m) from fueling

spot before starting the engine (fig. 5a).

Place the chain saw on firm ground or other solid

surface in an open area. Maintain a good balance and

secure footing. Place your right foot through the rear

handle opening and firmly grasp the front handle with

your left hand (fig. 6a).

Be absolutely sure that guide bar and chain are clear

of you or all other obstructions and objects, including

the ground, because when the engine starts in semi-

throttle position, engine speed will be fast enough for

the clutch to engage the sprocket and turn the chain

which may cause a kickback.

Never attempt to start the saw when the guide bar is in

a cut or kerf.

When you pull the starter grip, don’t wrap the starter

rope around your hands. Do not allow the grip to snap

back, but guide the starter rope slowly back to permit

the rope to rewind properly. Failure to follow this

procedure may result in injury to hand or fingers and

may damage the starter mechanism.

10 feet

Important adjustments

WARNING!

At correct idle speed, chain should not turn. For di-

rections to adjust idle speed, see the appropriate

section of this instruction manual.

Do not use a saw with incorrect idle speed adjust-

ment. Adjust the idle speed yourself according to

the appropriate section of this manual.

Have your MAKITA dealer check your saw and

make proper adjustments or repairs.

Check the saw chain tension frequently, especially

just after installing a new chain. New chains may

stretch more during their initial use. A properly

adjusted saw chain can be pulled freely around the

guide bar by hand without sagging. Always stop

the engine and wear gloves when checking or

adjusting the chain tension.

Working conditions

Operate your chain saw only outdoors. Operate the

saw under good visibility and daylight conditions only.

WARNING!

Take extreme care in wet and freezing weather

(rain, snow, ice). Put off the work when the weather

is windy, stormy or rainfall is heavy. Clear the area

where you are working.

WARNING!

Avoid stumbling on obstacles such as stumps,

roots or rocks and watch out for holes or ditches.

Be extremely cautious when working on slopes

or uneven ground. There is increased danger of

slipping on freshly debarked logs.

Cutting instructions

Always hold the saw firmly with both hands when the

engine is running. Place your left hand on the tubular

handle and your right hand on grip and throttle lever.

Left-handers should follow these instructions too.

WARNING!

Do not operate your chain saw in semi-throttle

position. Cutting in this position does not permit the

operator proper control of the saw or chain speed.

WARNING!

Never come too close to a rotating chain with your

hands or body.

WARNING!

Do not cut any material other than wood or

wooden objects.

Use your chain saw for cutting only. It is not

designed for prying or shoveling away limbs, roots

or other objects.

When sawing, make sure that the saw chain

does not touch any foreign materials such as

rocks, nails and the like (fig. 8). Such objects may

be flung off, damage the saw chain or cause the

saw to kick back.

Wrap your fingers tightly around the handles, keeping

the handles cradled between your thumb and forefinger

(fig. 7). With your hands in this position, you can best

oppose and absorb the push, pull and kickback forces of

your saw without having it slip out of your grip (see

section of reactive forces). Make sure your chain saw

handle and grip are in good condition and free of

moisture, pitch, oil or grease.

Always start a cut with the chain running at full speed and

the spike bar in contact with the wood.

WARNING!

Never use the saw with one hand. You cannot

control reactive forces (see pages 9 to 11) and may

lose control of the saw.

Position the chain saw in such a way that your body is

clear of the cutting attachment whenever the engine is

running (fig. 10).

Don’t put pressure on the saw when reaching the end

of a cut. The pressure may cause the bar and rotating

chain to pop out of the cut or kerf, go out of control and

strike the operator or some other object. If the rotating

chain strikes some other object a reactive force (see

pages 10 to 12 ) may cause the chain to strike the

operator.

Reactive forces during the cut, including kickback

WARNING!

Reactive forces, that may occur during any cut are

kickback, pushback and pull-in. Reactive forces

can be dangerous! In any chain saw, the powerful

force used to cut wood can be reversed (and work

against the operator).

If the rotating chain is suddenly stopped by contact

with any solid object like a log or branch or is

pinched, the reactive forces instantly occur. These

reactive forces may result in loss of control which

may, in turn, cause serious or fatal injury. An

understanding of the causes of these reactive

forces may help you avoid loss of control.

The most common reactive forces are

- kickback,

- pushback,

- pull-in.

In order to keep control of your saw, always maintain

a firm foothold. Never work on a ladder, in a tree or on

any other insecure support. Never use the saw above

shoulder height (fig. 9).

This reaction can occur in a fraction of a second and

under some circumstances, cause the guide bar and

chain to strike the operator with enough force to cause

severe or fatal injury. It may also occur during limbing.

It also occurs when the nose of the guide bar is pinched

unexpectedly, unintentionally contacts solid material

in the wood (fig.12) or is incorrectly used to begin a

plunge or boring cut.

The greater the force of the kickback reaction, the

more difficult it becomes for the operator to control the

saw.

Kickback:

Kickback occurs when the upper quadrant of the bar

nose contacts a solid object in the wood or is pinched

(fig. 11). The reaction of the cutting force of the chain

causes a rotational force of the chain saw in the direc

tion opposite to the chain movement, mainly in the

plane of the bar. This may fling the bar in an uncon-

trolled arc towards the operator.

Many factors influence the occurence and force of the

kickback reaction. The type of bar and saw chain you

use is a factor in the force of the kickback reaction.

The speed of contact at which the cutter contacts

the object.

Kickback force increase with the rate of impact.

The contact angle between the nose of the bar and

the foreign object (fig. 11).

Kickback is most pronounced in the upper quadrant of

the bar nose.

MAKITA chain types are designed to reduce kickback

forces.

The depth gauges:

Improper lowering of the depth gauges also increases

the risk of a kickback.

Saw chain cutter sharpness:

WARNING!

A dull improperly sharpened chain may increase

the risk of kickback. Always cut with a properly

sharpened chain.

Devices for reducing the risk of kickback injury

MAKITA have developed a special chain brake to

reduce the risk of kickbacks.

This chain brake increases the safety factor on the job,

e.g. when the saw suddenly bucks upwards the chain

stops rotating within a fraction of a second. A deflec-

tion guard on the disengaging lever of the chain brake

and a scoop rear handle ensure that the operator’s

hands are fully protected at all times.

Kickback tendency increases as the radius or size of

the guide bar nose increases. MAKITA have devel-

oped guide bars with small nose radius, to reduce the

kickback tendency.

WARNING!

No chain brake prevents kickback.

These brakes are designed only to stop the chain,

if activated.

To ensure a proper operation of the chain brake, it

must be properly maintained. Furthermore, there

must be a sufficient distance between the operator

and the bar to ensure that the chain brake has

sufficient time to activate and stop the chain before

potential contact with the operator.

To avoid kickback

The best protection from personal-injury that may

result from kickback is to avoid kickback situations:

1. Hold the chain saw firmly with both hands and

maintain a secure grip.

2. Be aware of the location of the guide bar nose at

all times.

3. Never bring the nose of the guide bar in contact

with any object. Do not cut limbs with the nose of

the guide bar. Be especially careful with small,

tough limbs, small size brush and saplings which

may easily catch the chain.

4. Don’t overreach.

5. Don’t cut above shoulder height.

6. Begin cutting and continue at full throttle.

7. Cut only one log at a time.

8. Use extreme caution when re-entering a previous

cut.

9. Do not attempt plunge cuts (see page 13) if you

are not experienced with these cutting techniques.

10. Be alert for shifting of the log or other forces that

may cause the cut to close and pinch the chain.

11. Maintain saw chain properly. Cut with a correctly

sharpened, properly tensioned chain at all times.

12. Stand to the side of the cutting path of the chain

saw.

To avoid pushback

1. Be alert to forces or situations that may cause

material to pinch the top of the chain.

2. Do not cut more than one log at a time.

3. Do not twist the saw when withdrawing the bar

from a plunge cut or under buck cut (figures 25 to

27 and 33, pages 13 and 14), because the chain

can pinch.

Pull-in:

Pull-in occurs when the chain on the bottom of the bar

is suddenly stopped. The chain on the bottom of the

bar stops when it is pinched, caught or encounters a

foreign object in the wood (see fig. 15). The reaction of

the chain pulls the saw forward, causing the operator

to lose control.

Pull-in frequently occurs when the spike bar of the

saw is not held securely against the tree or limb and

when the chain is not rotating at full speed before it

contacts the wood.

WARNING!

Use extreme caution when cutting small size brush

and saplings which may easily catch the chain and

pull you off balance.

To avoid pull-in

1. Always start a cut with the chain rotating at full

speed and the spike bar in contact with the wood.

2. Pull-in may also be prevented by using plastic

wedges to open the kerf or cut.

Cutting techniques

Felling

Felling is cutting down a tree.

Before felling a tree, consider carefully all conditions

which may affect the direction of fall, including:

The intended direction of the fall.

The neutral lean of the tree.

Any unusually heavy limb structure.

Surrounding trees and obstacles.

The wind direction and speed.

WARNING!

Always observe the general condition of the tree.

Look for decay and rot in the trunk. If it is rotted

inside, it could snap and fall toward the operator

while being cut.

Also look for broken or dead branches which could

vibrate loose and fall on the operator. When felling

on a slope, the operator should stand on the up-hill

side.

Pushback:

Pushback occurs when the chain on the top of the bar

is suddenly stopped when it is pinched, caught or

encounters a foreign object in the wood. The reaction

of the chain drives the saw straight back toward the

operator causing loss of saw control. Pushback fre-

quently occurs when the top of the bar is used for

cutting (fig. 14).

When felling in the vicinity of roads, railways and

power lines, etc., take extra precautions (see fig.

16). Inform the police, utility company or railway

authority before beginning to cut.

45°

= cutting down area

First clear the tree base and work area from interfering

limbs and brush and clean its lower portion with an axe

(see fig. 18).

When felling, maintain a distance of at least 2 1/2 tree

lengths from the nearest person (see fig. 17)

Note:

The noise of your engine may drown any warning call.

Felling instructions:

45°

Then, establish a path of escape and remove all

obstacles. This path should be opposite to the planned

direction of the fall of the tree and at a 45° angle (fig.

19). An alternate path must also be selected. Place all

tools and equipment a safe distance away from the

tree, but not on the escape path.

Then, determine the placement of the felling notch

(fig. 21). The felling notch when properly placed de-

termines the direction in which the tree will fall. It is

made perpendicular to the line of fall and should be as

close to the ground as possible. Cut the felling notch to

a depth of about one-fifth to one-fourth of the trunk

diameter (fig. 22). It should be in no case higher than

it is deep. Make the felling notch very carefully.

1/10∅

1/5∅

(4cm)

Felling notch

Hinge

Felling cut

Direction of fall

Hinge

Felling notch

First cut

Second cut

If the tree has large buttress roots, cut into the largest

buttresses vertically first (horizontally next) and remove

(fig. 20).

Begin the felling cut slighty higher than the felling

notch and on the opposite side of the tree (fig. 22).

Then cut horizontally through towards the felling notch.

Apply the chain saw with its spikes directly behind the

uncut portion of wood and cut toward the notch (fig.

23). Leave approximately 1/10 of the tree diameter

uncut! This is the hinge (fig. 23). Do not cut through the

hinge because you could lose control of the direction

of the fall. Drive wedges into the felling cut where

necessary to control the direction of the fall. Wedges

should be of wood, light alloy or plastic - never of steel,

which can cause kickback and damage to the chain.

Always keep to the side of the falling tree. When the

tree starts to fall, shut off the engine, withdraw the bar

and walk away on the pre-planned escape path. Watch

out for falling limbs.

WARNING!

Be extremely careful with partially fallen trees which

are poorly supported.

When the tree hangs or for some other reason does

not fall completely, set the saw aside and pull the

tree down with a cable winch, block and tackle or

tractor. If you try to cut it down with your saw, you

may be injured.

Sectioning Method

WARNING!

Felling a tree that has a diameter greater than the

length of the guide bar requires use of either the

sectioning or plunge-cut method. These methods

are extremely dangerous because they involve the

use of the nose of the guide bar and can result in

kickback. Only properly trained professionals should

attempt these techniques.

For the sectioning method (fig. 24) make the first cut

with the guide bar fanning in toward the hinge. Then,

using the bumper spike as a pivot, reposition the saw

for the next cut. Avoid repositioning the saw more than

necessary. When repositioning for the next cut, keep

the guide bar fully engaged in the kerf to keep the

felling cut straight. If the saw begins to pinch, insert a

wedge to open the cut. On the last cut, do not cut the

hinge.

Plunge-Cut Method

Timber having a diameter more than twice the length

of the guide bar requires the use of the plunge-cut

method before making the felling cut.

First, cut a large, wide notch. Make a plunge cut in the

center of the notch.

The plunge cut is made with the guide bar nose. Begin

the plunge cut by applying the lower portion of the

guide bar nose to the tree at an angle (fig. 25). Cut until

depth of the kerf is about the same as the width of the

guide bar (fig. 26). Next, align the saw in the direction

in which the recess is to be cut. With the saw at full

throttle, insert the guide bar in the trunk (fig. 27).

Enlarge the plunge cut as shown in illustration (fig. 28)

WARNING!

There is an extreme danger of kickback at this

point. Extra caution must be taken to maintain

control of the saw. To make the felling cut, follow

the sectioning method described previously (fig.

29). If you are inexperienced with a chain saw

plunge-cutting should not be attempted. Seek the

help of a professional.

Limbing

Limbing is removing the branches from a fallen tree.

WARNING!

There is an extreme danger of kickback during the

limbing operation. Do not work with the nose of the

bar. Be extremely cautious and avoid contacting

the log or other limbs with the nose of the guide bar.

Do not stand on a log while limbing it - you may slip

or the log may roll.

Start limbing by leaving the lower limbs to support

the log off the ground (fig. 30). Always cut from the

top of the limb. Do not underbuck freely hanging

limbs. A pinch may result or the limb may fall,

causing loss of control. If a pinch occurs, stop the

engine and remove the saw, by lifting the limb.

WARNING!

Be extremely cautious when cutting limbs under

tension. The limbs could spring back toward the

operator and cause loss of control of the saw or

injury to the operator.

Bucking

Bucking is cutting a log into sections.

WARNING!

1. When bucking, do not stand on the log. Make

sure the log will not roll down-hill. If on a slope,

stand on the up-hill side of the log (see fig. 31).

Watch out for rolling logs.

WARNING!

2. Cut only one log at a time.

WARNING!

3. Shattered wood should be cut very carefully.

Sharp slivers of wood may be caught and flung

in the direction of the operator of the saw.

WARNING!

4. When cutting small logs, use a sawhorse (fig.

32). Never permit another person to hold the

log. Never hold the log with your leg or foot.

1. Relieving cut

2. Cross cut

Tension side

Pressure side

1. Relieving cut

2. Cross cut

Tension side

Pressure side

Maintenance and Repair

Never operate a chain saw that is damaged, improp-

erly adjusted or not completely or securely assembled.

Follow the maintenance and repair instructions in the

appropriate section of this manual.

WARNING !

Always stop the engine and make sure that the

chain is stopped before commencing any mainte-

nance or repair work or cleaning the saw. Do not

attempt any maintenance or repair work not de-

scribed in this manual. Have such work performed

by your MAKITA service shop only.

Maintaining and storing the saw

Keep the chain, bar and sprocket clean and lubricated;

replace worn sprockets or chains.

Keep the chain sharp. You can spot a dull chain when

easy-to-cut wood becomes hard to cut and burn marks

appear on the wood.

Keep the chain at proper tension. Tighten all nuts,

bolts and screws except the carburetor adjustment

screws after each use.

Keep spark plug and wire connection tight and clean.

Store saws in a high or locked place, away from

children.

WARNING!

5. Logs under strain require special attention to

prevent the saw from pinching. The first cut is

made on the compression side to relieve the

stress on the log (see fig. 33, 34). The bucking

cut is then made as shown. If the saw pinches,

stop the engine and remove it from the log.

WARNING!

6. Only properly trained professionals should work

in an area where the logs, limbs and roots are

tangled (i. e. a blowdown area, fig. 35). Work-

ing in blowdown areas is extremely hazard-

ous.

WARNING!

7. Drag the logs into a clear area before cutting.

Pull out exposed and cleared logs first.

1 Tubular handle

2 Choke

3 Filter cover

4 Insert for normal / winter operation

5 Tubular handle

6 Muffler

7 Retaining nut

8 Spike bar

(toothed stop for holding saw steady against wood)

9 Chain catch

10 Automatic oil pump (bottom side)

11 Sprocket guard

12 Identification plate

13 Hand guard

14 Guide bar

15 Chain

16 Hand guard (release for chain brake)

17 Starter grip

18 Adjusting screws "speed-H-L" for carburetor

19 I/STOP-switch

20 Stop knob for halfway throttle

21 Safety locking button

22 Throttle lever

23 Fuel tank plug

24 Fan housing with starting assembly

25 Oil tank plug

26 Starting valve (only DCS-341 and DCS-401)

Denomination of components

1113

14 16

2219

Model

Serial no.

Identification plate

(example for type DCS 401)

DCS 401

16" (400mm)

9709 123456

442.040.661

028.100. 651

528.092.656

Hamburg,Germany

Indicate when ordering spare parts!

Approved bar and chain combinations

"Low-kickback saw chain is a chain which has met the

kickback performance requirements of ANSI B 175.1-

1991 (American National Standard for Power Tools-

Gasoline-Powered Chain Saws-Safety Requirements)

when tested on the representative sample of chain

saws below 3.8. C.l.D. specifed in ANSI B 175.1-

1991". The approved bar and chain combinations are

low kickback chains according to ANSI B 175.1-1991

and also meet the kickback requirements of CSA

Z62.3-96 for chain saws below 80 cm

The chain saw DCS 340, DCS 341, DCS 400, DCS

401 has been approved with following guide bar

and chain combinations:

Guide bar 3/8" Saw chain 3/8"

length Part no. Part no.

12" (30 cm) 442 030 661 528 092 646

14" (35 cm) 442 035 661 528 092 652

16" (40 cm) 442 040 661 528 092 656

"There may be other replacement bar and chain

combinations available that also reduces the risk of

injury from kickback".

WARNING

Do not use other replacement bars and chains

unless they have been designated as meeting the

ANSI B 175.1-1991 (for USA) and CSA Z62.3-96

(for Canada) kickback performance requirements

on that specific powerhead, or has been desig-

nated as "low kickback" saw chain in accordance

with the ANSI B 175.1-1991 (for USA) and CSA

Z62.3-96 (for Canada) standard.

Technical data DCS 340 DCS 341 DCS 400 DCS 401

Single-cylinder two-stroke

Piston displacement 2.0 cu. in (33 cm

) 2.0 cu. in (33 cm

) 2.4 cu. in (39 cm

)

Cylinder bore 1.45" (37 mm) 1.45" (37 mm) 1.57" (40 mm) 1.57" (40 mm)

Piston stroke 1.22" (31 mm) 1.22" (31 mm) 1.22" (31 mm) 1.22" (31 mm)

Max. power at speed 1.4/9,000 kW/rpm 1.4/9,000 kW/rpm 1.7/9,000 kW/rpm 1.7/9,000 kW/rpm

Max. torque at speed 1.7/6,500 Nm/rpm 1.7/6,500 Nm/rpm 2.0/6,500 Nm/rpm 2.0/6,500 Nm/rpm

Idling speed 2,600 rpm 2,600 rpm 2,600 rpm 2,600 rpm

Ignition system

Electronic, without breaker

Spark plug NGK BPMR 6F NGK BPMR 6F NGK BPMR 6F NGK BPMR 6F

or Spark plug

CHAMPION RDJ-7Y CHAMPION RDJ-7Y CHAMPION RDJ-7Y CHAMPION RDJ-7Y

Electrode gap .020" (0.5 mm) .020" (0.5 mm) .020" (0.5 mm) .020" (0.5 mm)

Fuel system

Carburetor (for Canada) WALBRO WT 174 WALBRO WT 174 WALBRO WT 174 WALBRO WT 174

Carburetor (for USA) WALBRO WT 466 WALBRO WT 466 WALBRO WT 466 WALBRO WT 466

(all position diaphragm carburetor

with integral fuel pump)

Air filter Robkoflok Robkoflok Robkoflok Robkoflok

Fuel tank capacity 13.3 oz. (0.4 l) 13.3 oz. (0.4 l) 13.3 oz. (0.4 l) 13.3 oz. (0.4 l)

Fuel mixture see chapter "Fuel" see chapter "Fuel" see chapter "Fuel" see chapter "Fuel"

Weight

without cutting attachment 8 lbs. 9 oz. (3.9 kg) 8 lbs. 9 oz. (3.9 kg) 8 lbs. 13 oz. (4.0 kg) 8 lbs. 13 oz. (4.0 kg)

Cutting attachment

Guide bar sprocket nose bar sprocket nose bar sprocket nose bar sprocket nose bar

Cutting length 12" (30 cm) 12" (30 cm) 12" (30 cm) 12" (30 cm)

14" (35 cm) 14" (35 cm) 14" (35 cm) 14" (35 cm)

16" (40 cm) 16" (40 cm) 16" (40 cm) 16" (40 cm)

Safety saw chain (pitch) 3/8" (528 092 ...) (528 092 ...) (528 092 ...) (528 092 ...)

Drive link gauge .050" X X X X

Chain sprocket 6 teeth (028 223 310) (028 223 310) (028 223 310) (028 223 310)

Chain lubrication fully automatic oil fully automatic oil fully automatic oil fully automatic oil

pump pump pump pump

Oil tank capacity 7.1 oz. (0.21 l) 7.1 oz. (0.21 l) 7.1 oz. (0.21 l) 7.1 oz. (0.21 l)

- Release the chain brake by pulling the hand guard (A/1)

towards the tubular handle (A/2) until you feel it catch.

- Unscrew retaining nut (B/3).

- Pull off the sprocket guard (B/4).

- Lift the chain (E/10) over the clutch drum and onto the

sprocket (E/11). Using your right hand, guide the chain

into the top guide groove on the guide bar (E/8).

NOTE: The cutting edges along the top of the chain must

point in the direction of the arrow!

- Lead the chain (F/10) around the sprocket nose (F/12) of

the guide bar.

NOTE: The chain should be easy to pull in the direction of the

arrow. The clutch drum (E/11) should turn with the chain (the

sprocket engages the chain).

CAUTION: Before doing any work on the guide bar or

chain,

always switch off the engine and pull

the plug cap off the spark plug (see "Replacing

the spark plug"). Always wear protective

gloves!

CAUTION: Start the chain saw only after having assem-

bled it completely and inspected!

PUTTING INTO OPERATION

Mounting the guide bar and saw chain

Use the universal wrench delivered with the chain saw for the

following work.

Put the chain saw on a stable surface and carry out the

following steps for mounting the guide bar and chain:

STOP

C D

- Turn the chain adjusting screw (C/6) to the left (counter-

clockwise) until the pin (C/7) is at the left stop.

- Position the guide bar (D/8). Make sure that the pin (D/9)

of the chain tightener is in the hole (circled) on the guide

bar.

G H

- Turn the chain tightener (C/6) to the right (clockwise)

until the chain engages the guide groove of the bottom side

of the bar (see circle). Press the guide bar against the

housing with your left hand.

NOTE:

If the chain brake on the dismounted sprocket guard is actu-

ated by accident, it must be released again prior to reassembly:

- Hold the sprocket guard (H/4) as shown (note direction of

arrow) firmly with both hands and press the stop lever

(H/13) against a hard surface (such as a board) until you

hear it catch.

- Replace the sprocket guard (I/4), making sure that the pin

on the stop lever fits into the space on the hand guard

(circled).

- Manually tighten the retaining nut (I/3).

NOTE:

The arrow (I/14) on the sprocket guard shows the direction of

chain travel.

Tightening the saw chain

- Slightly lift the end of the guide bar and turn the chain

adjusting screw (C/6) to the right (clockwise) until the chain

rests against the bottom side of the guide bar.

- While still holding up the guide bar, tighten the retaining nut

(J/3) with the universal wrench.

Checking the chain tension

- The tension of the chain is correct if the chain rests

against the bottom side of the guide bar and can still be

easily turned by hand. While doing so the chain brake

must be released.

- Every new chain must be broken in for about 2 to 3 minutes.

Ample chain lubrication is essential during this period.

After breaking in, check chain tension and adjust, if neces-

sary.

- When checking the chain tension the engine must be

switched off.

NOTE:

Check the chain tension frequently - chains tend to get longer

during use! If this is not done, there is a risk of the chain jumping

off the bar. It is recommended to use 2-3 chains alternatively.

In order to guarantee uniform wear of the guide bar the bar

should be turned over whenever replacing the chain.

STOP

The correct mixture ratio:

50:1 when using MAKITA high-performance two-stroke en-

gine oil, i. e. mix 50 parts gasoline with 1 part oil.

40:1 when using other two-stroke engine oils, i. e. mix 40

parts gasoline with 1 part oil.

Handling and storage

Utmost care is required when handling with fuel. Fuel can

contain substances which have a behavior similar to that of

solvents. Fill the tank only outside or ventilated rooms. Do not

inhale vapors, avoid any fuel contact with your skin. Fuel

cannot be stored. Purchase only the quantity needed for a

period of 4 weeks. Use licensed fuel containers only.

For preparing the fuel-oil mixture first mix the entire oil quantity

with half of the fuel required, then add the remaining fuel.

Thoroughly shake the mixture before pouring it into the chain

saw tank.

NOTE:

It is not wise to add more engine oil than specified to ensure

safe operation. This will only result in a higher production of

combus-tion residues which will pollute the environment and

clog the exhaust channel in the cylinder as well as the muffler.

In addition, fuel consumption will rise and performance will

decrease.

Chain oil

Use an oil with adhesive additive for lubricating the chain and

guide bar. The adhesive additive prevents the oil from being

flung off the chain too quickly.

Safety chain brake

Engaging the chain brake (braking)

In case of kickback the chain brake is engaged automatically by

inertial motion of the hand guard ((B/3).

To engage the chain brake manually, simply push the hand

guard (B/3) forward (towards the tip of the saw) with your left

hand (arrow 1).

Releasing the chain brake

Pull the hand guard (B/3) towards you (arrow 2) until you feel it

catch. The brake is now released.

OIL

MAKITA oil

50:1

Gasoline

40:1

other oil

1.0 Us-gal. (3.7 l) 2.5 floz. (75 cm

) 3.2 floz. (94 cm

)

2.5 Us-gal. (9.4 l) 6.4 floz. (189 cm

) 8.0 floz.(236 cm

)

5.0 Us-gal. (18.9 l) 12.8 floz. (378 cm

) 16.0 floz.(473 cm

)

BIOTOP

The models DCS 340/DCS 341/DCS 400 and DCS 401 comes

with an inertia chain brake as standard equipment. The chain

brake will automatically stop the chain if the kickback is

sufficiently strong, which is caused by the tip contacting wood

while the saw is running (see "SAFETY PRECAUTIONS",

page 9). The chain will stop within a fraction of a second.

The chain brake is installed to block the saw chain before

starting it and to stop it immediately in case of an emer-

gency.

Fuel / Refuelling

Fuel mixture

The engine of the chain saw is a high-efficiency two-stroke

engine. It runs on a mixture of gasoline and two-stroke engine oil.

The engine is designed for unleaded regular gasoline with a

min. octane value of 91 ROZ (research octane number). In

case no such fuel is available, you can use fuel with a higher

octane value. This will not affect the engine.

In order to obtain an optimum engine output and to

protect your health and the environment use unleaded

fuel only. Gasoline which contens alcohol should not

used in MAKITA products.

For lubricating the engine use a two-stroke engine oil (quality

grade: TC-3), which is added to the fuel. The engine has been

designed for use of MAKITA high-performance two-stroke

engine oil and a mixture ratio of only 50:1 to protect the

environment. In addition, a long service life and reliable oper-

ation with a minimum emission of exhaust gases are ensured.

MAKITA high-performance two-stroke engine oil is available in

the following sizes to suit your individual requirements:

1 l order number 980 008 607

100 ml order number 980 008 606

In case MAKITA high-performance two-stroke engine oil is not

available, it is urgently recommended to use a mixture ratio of

40:1, as otherwise optimum operation of the engine cannot be

guaranteed.

OIL

50:1

La page charge ...

Makita Chainsaw DCS 400 Manuel utilisateur

Marque: Makita

Modèle: Chainsaw DCS 400

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Makita Chainsaw DCS 400 User manual

Documents connexes

Autres documents

Dolmar ES-173 A Manuel utilisateur