Maytag Commercial MAT20MNAWW Guide d'installation

Marque
Maytag Commercial
Modèle
MAT20MNAWW
Catégorie
Machines à laver
Taper
Guide d'installation
W10837721A
W10861220A – SP
TABLE DES MATIÈRES
Page
Sécurité de la laveuse ........................................................... 20
Outillage et pièces ................................................................. 21
Dimensions ............................................................................ 22
Exigences d’emplacement ................................................... 23
Instructions d’installation ..................................................... 24
Établissement de l’aplomb de la laveuse ............................ 25
Raccordement du tuyau de vidange .................................... 26
Système de vidange .............................................................. 27
Raccordement des tuyaux d’arrivée d’eau ......................... 28
Spécications électriques .................................................... 29
Achever l’installation ............................................................. 30
Installation de la glissière et de la boîte à monnaie ........... 30
Taille typique des charges complètes ................................. 30
Entretien de la laveuse .......................................................... 31
Si vous avez besoin d’assistance ........................................ 32
Pièces supplémentaires et accessoires .............................. 32
Instructions de paramétrage des commandes
électroniques .........................................................................33
Garantie .................................................................................. 40
INSTALLATION
INSTRUCTIONS
CommerCial Washer
www.maytagcommerciallaundry.com
INSTRUCTIONS
D’INSTALLATION
laveuse CommerCiale
TABLE OF CONTENTS
Page
Washer Safety .......................................................................... 2
Tools & Parts ............................................................................ 3
Dimensions .............................................................................. 4
Location Requirements ...........................................................5
Installation instructions .......................................................... 6
Level Washer ............................................................................ 7
Connect Drain Hose ................................................................ 8
Drain System ............................................................................ 9
Connect Inlet Hoses .............................................................. 10
Electrical Requirements........................................................11
Complete Installation ............................................................ 12
Installing Coin Slide and Coin Box ....................................... 12
Typical Full Load Sizes .......................................................... 12
Washer Maintenance.............................................................13
If You Need Assistance ......................................................... 14
Alternate Parts & Accessories ............................................. 14
Electronic Controls Set-Up Instructions ............................. 15
Warranty ................................................................................. 19
2
WASHER SAFETY
3
TOOLS & PARTS
Parts Supplied:
Water Inlet Hoses (2) Inlet Hose Washers (4)
Tools Needed:
Level Pliers
Utility Knife
Flat-Blade Screwdriver
Optional tools:
Flashlight Bucket
9/16" (14 mm)
Open-End Wrench
Drain Hose with Clamp,
U-Form, and Cable Tie
4
DIMENSIONS
Front View
Back View
Non-coin-operated models Coin-operated models
27"
(686 mm)
36
3
/4"
(933 mm)
4
1
/4"
(108 mm)
1"
(25 mm)
6
3
/4"
(171 mm)
37
1
/4"
(946 mm)
10
1
/2"
(267 mm)
16"
(406 mm)
5
1
/2"
(140 mm)
42
1
/2"
(1.080 m)
Side View
44
1
/2"
(1.130 m)
27"
(686 mm)
4
1
/4"
(108 mm)
6
3
/4"
(171 mm)
37
1
/4"
(946 mm)
36
3
/4"
(933 mm)
10
1
/2"
(267 mm)
16"
(406 mm)
5
1
/2"
(140 mm)
1"
(25 mm)
42
1
/2"
(1.080 m)
36
1
/4"
(921 mm)
8
1
/4"
(210 mm)
1"
(25 mm)
27"
(686 mm)
Non-coin-operated
models:
6
1
⁄4" (159 mm)
Coin-operated
models:
8
1
⁄4" (210 mm)
5
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed in a basement, laundry room, or
recessed area. See “Drain System.”
Companion appliance location requirements should also be
considered.
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather. Do not store or operate the washer in
temperatures at or below 32°F (0°C). Some water can remain in
the washer and can cause damage in low temperatures. Proper
installation is your responsibility.
You will need:
n A water heater set to 120°F (49°C).
n A grounded electrical outlet located within 4 ft. (1.2 m) of
power cord on back of washer. See “Electrical Requirements.”
n Hot and cold water faucets located within 4 ft. (1.2 m) of
hot and cold water ll valves on washer, and water pressure
of 20–100 psi (138–690 kPa). A pressure reduction valve
should be used in the supply line where inlet pressure entering
the building exceeds 100 PSI (690 kPa) to avoid damage to
the washer mixing valve.
n Single washer installations require 12" (300 mm) minimum
risers to provide an air cushion and avoid noise and damage
to valves.
n A level oor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet is not recommended.
n
Floor must support washer’s total weight (with water and load)
of 315 lbs (143 kgs).
n A oor drain under the bulkhead. Prefabricated bulkheads
with electrical outlets, water inlet lines, and drain facilities
should be used only where local codes permit.
LOCATION REQUIREMENTS
Recessed Area or Closet Installation
This washer may be installed in a recessed area or closet.
The installation dimensions shown are the minimum spaces
allowable. Additional spacing should be considered for ease of
installation and servicing. If closet door is installed, the minimum
air openings in top and bottom of door are required. Louvered
doors with air openings in top and bottom are acceptable.
Companion appliance spacing should be considered.
Minimum installation spacing
6
INSTALLATION INSTRUCTIONS
It is necessary to remove all shipping materials for proper
operation and to avoid excessive noise from washer.
1. Move washer to within 4 ft (1.2 m) of its nal location; it must
be in a fully upright position.
NOTE: To avoid oor damage, set washer onto cardboard
before moving it and make sure lid is taped shut.
2. To avoid damaging oor, place cardboard supports from
shipping carton on oor behind washer. Tip washer back
and place on cardboard supports. Remove shipping base.
Set washer upright.
IMPORTANT: Removing shipping base is necessary for proper
operation.
NOTE: Keep shipping base in case you need to move washer
later.
48"
(1.2 m)
3. Remove tape from washer lid, open lid, and remove cardboard
packing tray from tub. Be sure to remove all parts from tray.
NOTE: Keep tray in case you need to move washer later.
7
1. Move the washer to its nal location. Place a level on top
edges of washer. Use side seam as a guide to check levelness
of sides. Check levelness of front using lid, as shown. Rock
washer back and forth to make sure all four feet make solid
contact with oor.
LEVEL WASHER
IMPORTANT: Level washer properly to reduce excess noise
and vibration.
Not Level LEVEL Not Level
2. Use a 9/16" or 14 mm open-end or adjustable wrench to turn
jam nuts clockwise on feet until they are about 1/2" (13 mm)
from the washer cabinet. Then turn the leveling foot clockwise
to lower the washer or counterclockwise to raise the washer.
Recheck levelness of washer and repeat as needed.
Place level here
Place level here
3. When washer is level, use a 9/16" or 14 mm open-end or
adjustable wrench to turn jam nuts counterclockwise on leveling
feet tightly against washer cabinet.
HELPFUL TIP: You may want to prop up front of washer about
4" (102 mm) with a wood block or similar object that will support
weight of washer.
Place level here
Place level here
Jam nut
Jam nut
Jam nut
Jam nut
8
8"
(203 mm)
Proper routing of the drain hose avoids damage to your oor
due to water leakage.
Remove drain hose from the washer basket
1. Remove cap from the washer drain port on the back of
the washer.
2. If clamp is not already in place on elbow end of drain hose,
slide it over end as shown.
3. Squeeze clamp with pliers and slide elbow end of drain
hose onto washer drain port and secure with clamp.
4. The washer drain system can be installed using a oor drain,
wall standpipe, oor standpipe, or laundry tub.
CONNECT DRAIN HOSE
5. Place hose into standpipe (shown in picture) or over side
of laundry tub.
IMPORTANT:
n
Drain hose is not to exceed 8" (203 mm) into drain pipe;
do not force excess hose into standpipe or lay on bottom
of laundry tub. Drain hose form must be used.
n
It is the responsibility of the installer to install and secure
the drain hose into the provided plumbing/drain in a
manner that will avoid the drain hose coming out of,
or leaking from, the plumbing/drain.
6. For oor drain installations, you will need to remove the drain
hose form from the end of the drain hose. You may need
additional parts with separate directions. See “Tools and Parts.”
7. The oor drain system requires a siphon break that may be
purchased separately. The siphon break (Part Number 285320)
must be a minimum of 28" (710 mm) from the bottom of the
washer. Additional hoses might be needed.
Drain
hose
form
9
DRAIN SYSTEM
Drain system can be installed using a oor drain, wall standpipe,
oor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 10 gal. (38 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than
96" (2.44 m) from bottom of washer.
Laundry tub drain system
8"
(203 mm)
8"
(203 mm)
39"
(990 mm)
8"
(203 mm)
Wall standpipe drain system
See requirements for oor standpipe drain system.
Floor drain system
Floor drain system requires a Siphon Break Kit (Part Number
285320). Minimum siphon break: 28" (710 mm) from bottom
of washer. Additional hoses may be needed.
Minimum capacity: 20 gal. (76 L). The top of the laundry tub
must be at least 39" (990 mm) above oor.
39"
(990 mm)
10
CONNECT INLET HOSES
Connect Inlet Hoses to Washer
1. Attach cold water hose to cold water inlet valve marked
with a blue ring. Screw coupling by hand until it is snug.
2. Attach hot water hose to hot water inlet valve marked
with a red ring. Screw coupling by hand until it is snug.
3. Use pliers to tighten couplings an additional two-thirds turn.
NOTE: Do not overtighten. Damage to the valve can result.
4. Turn on water faucets to check for leaks. A small amount
of water may enter washer. It will drain later.
NOTE: Replace inlet hoses after 5 years of use to reduce the
risk of hose failure. Record hose installation or replacement
dates on the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
Insert new hose washers (supplied) into each end of the inlet
hoses. Firmly seat the washers in the couplings.
Connect Inlet Hoses to Water Faucets
1. Attach hose to hot water faucet. Screw on coupling until
it is seated on washer. Repeat process for cold water.
2. Use pliers to tighten the couplings an additional
two-thirds turn.
IMPORTANT: Do not overtighten or use tape or sealants on valve
when attaching to faucets or washer. Damage can result.
3. Secure drain hose to inlet hose with zip strap.
Clear Water Lines
n Run water through both faucets and inlet hoses,
into a laundry tub, drainpipe, or bucket to get
rid of particles in the water lines that might clog
the inlet valve screens.
n Check the temperature of the water to make
sure that the hot water hose is connected to the
hot water faucet and that the cold water hose is
connected to the cold water faucet.
CouplingWasher
11
ELECTRICAL REQUIREMENTS
n
A 120-volt, 60 Hz., AC-only, 15- or 20-amp, fused electrical supply
is required. A time-delay fuse or circuit breaker is recommended.
It is recommended that a separate circuit breaker serving only
this appliance be provided.
n
This washer is equipped with a power supply cord having
a 3 prong grounding plug.
n
To minimize possible shock hazard, the cord must be plugged
into a mating, 3 prong, grounding-type outlet, grounded in
accordance with local codes and ordinances. If a mating outlet
is not available, it is the personal responsibility and obligation
of the customer to have the properly grounded outlet installed
by a qualied electrician.
n
If codes permit and a separate ground wire is used, it is
recommended that a qualied electrician determine that
the ground path is adequate.
n
Do not ground to a gas pipe.
n
Check with a qualied electrician if you are not sure the
washer is properly grounded.
n
Do not have a fuse in the neutral or ground circuit.
12
INSTALLING COIN SLIDE AND COIN BOX
The coin slide mechanism, service door lock and key, and coin
box lock and key are not included with some models, but can
be obtained from the usual industry sources.
Remove the service door of the meter case by lifting it up
at the back. Install the money-accepting device. (Refer to
manufacturer’s instructions for proper installation.)
A ground connection is needed for the coin slide, which can be
made by connecting the available harness (W10846503) to the
coin slide.
Install a lock and cam on the meter case service door. Install
the coin vault with lock and key in the meter case opening.
Ground
connection
q
Check electrical requirements. Be sure that you have
the correct electrical supply and the recommended
grounding method.
COMPLETE INSTALLATION
q
Check that all parts are now installed. If there is an extra part,
go back through steps to see what was skipped.
q Check that you have all of your tools.
q Check that shipping materials were completely removed
from washer.
q Dispose of/recycle all packaging materials.
q Check that the water faucets are on.
q Check for leaks around faucets and inlet hoses.
q Remove lm from console and any tape remaining on
washer.
q Plug into a grounded outlet or connect power.
q Check that circuit breaker is not tripped or fuse is not blown.
q
Start the washer using the payment system if used and
check that the washer completes the cycle without a fault
or water leak.
TYPICAL FULL LOAD SIZES
Load Type Loading Suggestion Load Type Loading Suggestion
Mixed Load 3 double sheets
4 pillowcases
6 pair shorts
8 T-shirts
2 shirts
2 blouses
8 handkerchiefs
Heavy Work Clothes 3 pair pants
3 shirts
1 coverall
4 pair jeans
1 overall
Permanent Press 2 double or
1 king size sheet
1 tablecloth
1 dress
1 blouse
2 slacks
3 shirts
2 pillowcases
Knits 3 blouses
4 slacks
6 shirts
4 tops
4 dresses
13
WASHER MAINTENANCE
It is recommended that berglass items not be washed in
coin-operated washers. If these items are washed in the
washer, run the washer through a complete cycle to rinse
any residue away that might be left in the washer.
Operating Tips
Transporting Your Washer
n
Shut off both water faucets. Disconnect and drain water inlet
hoses.
n
Disconnect drain from drain system and drain any remaining
water into a pan or bucket. Disconnect drain hose from back
of washer.
n
Unplug power cord.
n
Place inlet hoses and drain hose inside washer basket.
n
Drape power cord over edge and into washer basket.
n
Place packing tray from original shipping materials back inside
washer and reuse shipping base to support the motor and tub.
If you do not have original packaging, place heavy blankets
or towels above basket, between the washer top and the
tub ring. Close lid and place tape over lip and down the front
of the washer. Keep lid taped until washer is moved to new
location.
14
Contact your authorized Commercial Laundry distributor. To locate your authorized Commercial Laundry distributor, or for web
inquiries, visit www.MaytagCommercialLaundry.com.
If you cannot locate your distributor, the Commercial Laundry Support Center will answer any questions about operating or
maintaining your washer not covered in the Installation Instructions.
Just dial 1-800-662-3587 — the call is toll free.
When you call, you will need the washer model number and serial number. Both numbers can be found on the serial-rating plate
located on the washer.
IF YOU NEED ASSISTANCE
Whirlpool Corporation, Benton Harbor, Michigan 49022, U.S.A.
ALTERNATE PARTS & ACCESSORIES
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free
number in the “If You Need Assistance” section.
If You Have: You Will Need:
Overhead sewer Standard 20 gal. (76 L) 39"
(990 mm) tall drain tub or utility
sink, sump pump and connectors
(available from local plumbing
suppliers)
1" (25 mm) standpipe 2" (51 mm) diameter to
1" (25 mm) diameter Standpipe
Adapter Part Number 3363920
Connector Kit Part Number
285835
Lint clogged drain Drain Protector Part Number
367031 Connector Kit Part
Number 285835
Floor drain system Siphon break, Part Number
285320 Connector Kit (x2) Part
Number 285835 Extension Drain
Hose Part Number 285863
Water faucets beyond
reach of ll hoses
2 longer water ll hoses:
6 ft. (1.8 m) 90° bend hose
Part Number 76314, 10 ft. (3.0 m)
Part Number 350008
Inlet hoses are sold as a pair
in kit W10575888
Accessories
Washer Drip Trays
Part Number 8212526
Fabric Softener Dispenser Kit
Part Number 63594
Drain beyond reach of
drain hose
4 ft. (1.2 m) Drain Hose Extension
Part Number DRNEXT4
15
ELECTRONIC CONTROLS SET-UP INSTRUCTIONS
Basic Operation of Commercial Washer
n For additional information, see www.MaytagCommercialLaundry.com.
IMPORTANT
Electrostatic Discharge (ESD)
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is nished, but
failure may occur at a later date due to ESD stress.
n Use an anti-static wrist strap. Connect wrist strap to green
ground connection point or unpainted metal in the washer.
-OR-
Touch your nger repeatedly to a green ground connection
point or unpainted metal in the washer.
n Before removing the part from its package, touch the
anti-static bag to a green ground connection point or
unpainted metal in the washer.
n Avoid touching electronic parts or terminal contacts; handle
electronic control assembly by edges only.
n When repackaging failed electronic control assembly in
anti-static bag, observe above instructions.
GENERAL INFORMATION
Blank Display
This condition indicates the washer is inoperative.
‘0 Minutes’ showing in display
This condition indicates the washer cannot be operated. Coins
dropped or debit inputs during this condition will be stored in
escrow but cannot be used until normal operation is restored by
opening and closing the door. If a door switch fails, it must be
replaced before normal operation can be restored.
Cold Start (initial first use)
Washer is programmed at the factory as follows:
n POWERWASH = 12 min agitation
MIXED = 9 min agitation
DELICATES = 6 min agitation
NORMAL ECO = 8 min agitation
n MIXED = 1 rinse and 2 minutes of rinse agitation
POWERWASH = 1 deep rinse with spin out
DELICATES = 1 deep rinse with spin out
NORMAL ECO = 1 spray rinse
n MIXED = $2.00
DELICATES = $1.75
POWERWASH = $2.50
NORMAL ECO = $1.75
Warm Start (after power failure)
After a delay of up to 8 seconds, the washer is restored to
the portion of the cycle that existed at time of the power failure.
To continue the cycle, press START.
Free Cycles
This is established by setting the cycle price to zero. When this
happens, ‘SELECT CYCLE’ will appear and cycle price will show
0.00.
Debit Card Ready
This washer is debit card ‘cable’ ready. It will accept a variety of
debit card systems, but does NOT come with a debit card reader.
Refer to the debit card reader manufacturer for proper washer
setup. In models converted to a Generation 1 debit card system,
debit pulses represent the equivalent of one coin (coin 1).
Display
After the washer has been installed and plugged in, the display
will show ‘SYnC’ for a few seconds, then ‘0 MINUTES’. Once the
washer has been plugged in and the washer door opened and
closed, the display will show the price. In washers set for free
cycles, the display will ash ‘SELECT CYCLE’, and will display
‘PRICE 0.00’.
OPTIONSCYCLES
DEEP WATER
POWERWASH
TEMPERATURE
SOIL LEVEL
EXTRA RINSE
MIXED
DELICATES
NORMAL
ECO
16
ELECTRONIC CONTROLS SET-UP INSTRUCTIONS
Control Set-Up Procedures
IMPORTANT: Read all instructions before operating.
The lower fabric setting key pads and the digital display are
used to set up the controls. The display can contain four numbers
and/or letters and a decimal point. These are used to indicate
the set-up codes and related code values available for use in
programming the washer.
How to use the key pads to program the controls
1. The POWERWASH key pad is used to adjust the values
associated with set-up codes. Pressing the key pad will
increment the value.
Rapid adjustment is possible by holding the key pad down.
2. The MIXED key pad will advance you through the set-up
codes. Pressing the key pad will advance you to the next
available set-up code. Holding the key pad down will
automatically advance through the set-up codes at
a rate of one (1) per second.
3. The DELICATES key pad is used to select or deselect options.
4. The TEMPERATURE key pad is used to decrease set-up code
value.
Start Operating Set-Up
n PD Models: Insert access door key, turn, and lift to remove
access door.
n PR models set for free vend: Refer to bottom of page 18 for
entering operating setup.
n PR Models: Once the debit card reader is installed (according
to the reader manufacturer’s instructions), the set-up mode
can be entered by inserting a set-up card (supplied by the
reader manufacturer) into the card slot. If a manual set-up
card is not available, manual set-up mode can be entered
by removing connector AA1 on the circuit board.
IMPORTANT: The console must not be opened unless power is
rst removed from the washer. To access connector AA1:
g
Unplug washer or disconnect power.
g
Open console, disconnect plug on AA1, close console.
g
Plug in washer or reconnect power.
The washer is now in the set-up mode.
Before proceeding, it is worth noting that, despite all of the
options available, an owner can simply choose to uncrate a new
commercial washer, hook it up, plug it in, and have a unit that
operates.
Set-Up Codes
n The MIXED key pad will advance from code to code.
n The POWERWASH key pad will increase the code value.
n The DELICATES key pad will select or deselect options.
n The TEMPERATURE key pad will decrease the code value.
FOR PR MODELS: The set-up codes are the same as for the ‘PD’
models except where noted.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
CODE EXPLANATION
6.07
NORMAL
ECO
NORMAL ECO Regular Cycle Vend Price - Increase or
decrease between 0 and 200 by pressing the POWERWASH or
TEMPERATURE key pad. Factory preset for 7 quarters = $1.75.
PR/PN MODELS ONLY: Factory preset for 0 quarters (Free Vend).
6.07
POWERWASH
POWERWASH Regular Cycle Vend Price - Increase or
decrease between 0 and 200 by pressing the POWERWASH or
TEMPERATURE key pad. Factory preset for 7 quarters = $1.75.
PR/PN MODELS ONLY: Factory preset for 0 quarters (Free Vend).
6.08
MIXED
MIXED Regular Cycle Vend Price - Increase or decrease between
0 and 200 by pressing the POWERWASH or TEMPERATURE key
pad. Factory preset for 8 quarters = $2.00.
PR/PN MODELS ONLY: Factory preset for 0 quarters (Free Vend).
g Press the MIXED key pad once to advance to next code.
P.dEF
Default Cycle Price displayed in Standby - Increase or decrease
between MIXED, DELICATES, POWERWASH, NORMAL ECO by
pressing the POWERWASH or TEMPERATURE key pad. Factory
preset for MIXED.
7.00
ADDITIONAL WASH TIME
7.00
This is the number of minutes that can be added to a Wash Cycle.
Choose from 00-05 minutes by pressing the POWERWASH key pad.
g Press the MIXED key pad once to advance to next code.
8.00
ADDITIONAL RINSE TIME
8.00
This is the number of minutes that can be added to a Rinse Cycle.
Choose from 00-05 minutes by pressing the POWERWASH key pad.
g Press the MIXED key pad once to advance to next code.
9.00
CYCLE COUNTER OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.
9.00
Not Selected ‘OFF’.
9.0C
Selected ‘ON’ and not able to be deselected.
Press the DELICATES key pad 3 consecutive times to select ‘ON’.
Once selected ‘ON’ it cannot be deselected.
g Press the MIXED key pad once to advance to next code.
1.00
MONEY COUNTER OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.
1.00
Not Selected ‘OFF’.
1.0C
Selected ‘ON’.
Press the DELICATES key pad 3 consecutive times to select ‘ON’
and 3 consecutive times to remove (Not Selected ‘OFF’.) Counter
resets by going from ‘OFF’ to ‘ON’.
1.C0
Selected ‘ON’ and not able to be deselected.
To select ‘ON’ and not able to be deselected, rst select ‘ON’,
then within 2 seconds press the DELICATES key pad twice,
the POWERWASH key pad once, and exit the set-up mode.
g Press the MIXED key pad once to advance to next code.
2.00
SPECIAL PRICING OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.
2.00
Not Selected ‘OFF’.
2.SP
Selected ‘ON’. Press the DELICATES key pad once for this selection.
If SPECIAL PRICING OPTION is selected, there is access to codes ‘3.’
through ‘9.’.
NOTE: An external battery needs to be added to keep the clock running during
periods of power outages.
g Press the MIXED key pad once to advance to next code.
CODE EXPLANATION
6.07
DELICATES
DELICATES Regular Cycle Vend Price - Increase or decrease
between 0 and 200 by pressing the POWERWASH or
TEMPERATURE key pad. Factory preset for 7 quarters = $1.75.
PR/PN MODELS ONLY: Factory preset for 0 quarters (Free Vend).
17
ELECTRONIC CONTROLS SET-UP INSTRUCTIONS
CODE EXPLANATION
OPTIONS TO USE IF SPECIAL PRICING IS SELECTED:
3.07
DELICATES
DELICATES Special Cycle Vend Price - Increase or decrease
between 0 and 200 by pressing the POWERWASH or
TEMPERATURE key pad. Factory preset for 7 quarters = $1.75.
PR/PN MODELS ONLY: Factory preset for 0 quarters (Free Vend).
3.07
Normal ECO
Normal ECO Special Cycle Vend Price - Increase between 0
and 200 by pressing the POWERWASH key pad and decrease
by pressing the TEMPERATURE key pad. Factory preset for
7 quarters = $1.75.
PR/PN MODELS ONLY: Factory preset for 0 quarters (Free Vend).
3.07
POWERWASH
POWERWASH Special Cycle Vend Price - Increase or
decrease between 0 and 200 by pressing the POWERWASH or
TEMPERATURE key pad. Factory preset for 7 quarters = $1.75.
PR/PN MODELS ONLY: Factory preset for 0 quarters (Free Vend).
3.08
MIXED
MIXED Special Cycle Vend Price - Increase or decrease between
0 and 200 by pressing the POWERWASH or TEMPERATURE key
pad. Factory preset for 8 quarters = $2.00.
PR/PN MODELS ONLY: Factory preset for 0 quarters (Free Vend).
g Press the MIXED key pad once to advance to next code.
5.00
TIME-OF-DAY CLOCK, MINUTES
5.00
This is the TIME-OF-DAY CLOCK, minute setting; select between 0 and
59 minutes by pressing the POWERWASH or TEMPERATURE key pad.
g Press the MIXED key pad once to advance to next code.
6.00
TIME-OF-DAY CLOCK, HOURS
NOTE: Uses military time or 24 hr. clock.
6.00
This is the TIME-OF-DAY CLOCK, hour setting; select between 0 and
23 hours by pressing the POWERWASH or TEMPERATURE key pad.
g Press the MIXED key pad once to advance to next code.
7.00
SPECIAL PRICE START HOUR
NOTE: Uses military time or 24 hr. clock.
7.00
This is the start hour; select between 0 and 23 hours by pressing
the POWERWASH or TEMPERATURE key pad.
g Press the MIXED key pad once to advance to next code.
8.00
SPECIAL PRICE STOP HOUR
NOTE: Uses military time or 24 hr. clock.
8.00
This is the stop hour; select between 0 and 23 hours by pressing
the POWERWASH or TEMPERATURE key pad.
g Press the MIXED key pad once to advance to next code.
9.00
SPECIAL PRICE DAY
9.10
This represents the day of the week and whether special pricing
is selected for that day. A number followed by ‘0’ indicates no
selection that particular day (9.10). A number followed by an ‘S’
indicates selected for that day (9.1S).
Days of the week (1-7) can be chosen by pressing the
POWERWASH key pad. Press the POWERWASH key pad once to
select special pricing for each day chosen.
When exiting set-up code ‘9’, the display must show current day
of week:
DISPLAY DAY OF WEEK CODE (selected)
10 Day 1 = Sunday 1S
20 Day 2 = Monday 2S
30 Day 3 = Tuesday 3S
40 Day 4 = Wednesday 4S
50 Day 5 = Thursday 5S
60 Day 6 = Friday 6S
70 Day 7 = Saturday 7S
CODE EXPLANATION
g Press the MIXED key pad once to advance to next code.
A.00
VAULT VIEWING OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.
A.00
Not Selected ‘OFF’.
A.SC
Selected ‘ON’. Press the DELICATES key pad once for this
selection. When selected, the money and/or cycle counts will be
viewable (depending on what is selected) when the coin box is
removed.
g Press the MIXED key pad once to advance to next code.
b.05
VALUE OF COIN 1
b.05
This represents the value of coin 1 in number of nickels:
05 = $0.25.
By pressing the POWERWASH or TEMPERATURE key pad, there
is the option of between 1 and 199 nickels.
g Press the MIXED key pad once to advance to next code.
C.20
VALUE OF COIN 2
C.20
This represents the value of coin 2 in number of nickels:
20 = $1.00.
PR MODELS ONLY: Factory preset for $0.25.
By pressing the POWERWASH or TEMPERATURE key pad, there
is the option of between 1 and 199 nickels.
g Press the MIXED key pad once to advance to next code.
d.00
COIN SLIDE OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.
d.00
Not Selected ‘OFF’.
d.CS
Selected ‘ON’. Press the DELICATES key pad 3 consecutive times
for this selection.
When coin slide mode is selected, set ‘b.’ equal to value of slide in
nickels. Set Step 6 (regular cycle price) and Step 3 (special cycle
price) to number of slide operations. If the installer sets up ‘CS’ on
a coin drop model, it will not register coins.
g Press the MIXED key pad once to advance to next code.
E.00
ADD COINS OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.
This option causes the customer display to show the number of
coins (coin 1) to enter, rather than the dollars-and-cents amount.
E.00
Not Selected ‘OFF’.
E.AC
Selected ‘ON’. Press the DELICATES key pad 3 consecutive times
for this selection.
g Press the MIXED key pad once to advance to next code.
H.00
COLD
COLD Temperature Upgrade Price - Increase or decrease between
0 and 200 by pressing the POWERWASH or TEMPERATURE key
pad. Factory preset for 0 quarters = $0.00.
H.00
COOL
COOL Temperature Upgrade Price - Increase or decrease between
0 and 200 by pressing the POWERWASH or TEMPERATURE key
pad. Factory preset for 0 quarters = $0.00.
H.00
WARM
WARM Temperature Upgrade Price -
Increase or decrease between
0 and 200 by pressing the POWERWASH or TEMPERATURE key
pad. Factory preset for 0 quarters = $0.00.
H.01
HOT
HOT Temperature Upgrade Price - Increase or decrease between
0 and 200 by pressing the POWERWASH or TEMPERATURE key
pad. Factory preset for 1 quarter = $0.25.
18
ELECTRONIC CONTROLS SET-UP INSTRUCTIONS
CODE EXPLANATION
H.01
HEAVY
HEAVY SOIL LEVEL Upgrade Price - Increase or decrease between
0 and 200 by pressing the POWERWASH or
TEMPERATURE
key
pad. Factory preset for 1 quarter = $0.25.
H.01
EXTRA
RINSE
EXTRA RINSE Upgrade Price - Increase or decrease between 0
and 200 by pressing the POWERWASH or TEMPERATURE key
pad. Factory preset for 1 quarter = $0.25.
g Press the MIXED key pad once to advance to next code.
J.Cd
COIN/DEBIT OPTION
J.Cd
Both coin & debit selected.
J.C_
Coins selected, debit disabled. Press the DELICATES key pad
3 times for this selection.
J._d
Debit Card selected, coins disabled. Press the DELICATES key
pad 3 times for this selection.
J.Ed
Enhanced Debit is self-selected when a Generation 2 card reader
is installed in the washer. The Ed option cannot be manually
selected or deselected.
g Press the MIXED key pad once to advance to next code.
L.00
PRICE SUPPRESSION OPTION
This option causes the customer display to show ‘ADD’ or
‘AVAILABLE’ rather than the amount of money to add. (Used
mainly in debit installations.)
L.00
Not Selected ‘OFF’.
L.PS
Selected ‘ON’. Press the DELICATES key pad once for this
selection.
g Press the MIXED key pad once to advance to next code.
n. CE
CLEAR ESCROW OPTION
When selected, money held in escrow for 30 minutes without
further escrow or cycle activity will be cleared.
n. CE
Selected ‘ON’.
n. 00
Not selected ‘OFF’. Press the DELICATES key pad once to
deselect this selection.
g Press the MIXED key pad once to advance to next code.
U.00
PENNY INCREMENT OFFSET
U.00
This represents the penny increment price offset used in
Generation 2 (Enhanced Debit) PR models. Choose from 0-4
pennies by pressing the POWERWASH key pad.
g Press the MIXED key pad once to advance to next code.
A3.03
MIXED Cycle Settings. Allows the owner to select the cycle default
options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specic settings. MIXED is set to 03 from the
factory.
A4.01
DELICATES Cycle Settings. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specic settings. Delicates is set to 01 from the
factory.
A5.1C
POWERWASH Cycle Settings. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specic settings. Powerwash is set to 1C from the
factory.
A6.03
NORMAL ECO Cycle Settings. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specic settings. Normal Eco is set to 03 from the
factory.
If cycle counter (9.0C) is selected, the following is true:
1 xx Number of cycles in THOUSANDS. 1 02 = 2,000
2xxx Number of cycles in ONES. 2225 = 225
TOTAL CYCLES = 2,225
This is “VIEW ONLY” and cannot be cleared.
Press the
MIXED
key pad once to advance
to next code.
If money counter (1.0C or 1.C0) is selected, the following is
true:
3 xx Number of dollars in HUNDREDS. 3 01 = $1,000.00
4xxx Number of dollars in ONES. 4600 = $ 600.00
5 xx Number of CENTS. 5 75 = $ 00.75
TOTAL = $1,600.75
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
n PD Models: Reinstall access door.
n PR Models:
g
Unplug washer or disconnect power.
g
Open console, reinsert plug into AA1, close console.
g
Plug in washer or reconnect power.
If preferred, just wait through 2 minutes of inactivity. All settings
will be saved and the display will revert to Select Cycle screen.
Table 1
Technician Service Access Code
This method is only available on PR washers set to free vend
(6 00).
To enter service mode:
Press the POWERWASH, EXTRA RINSE, TEMPERATURE, and
DELICATES key pads within 10 seconds.
To exit service mode:
From service code 8.xx, press the POWERWASH key pad
for 4 seconds.
or
Wait 2 minutes without touching any key pads (without diagnostic
modes running).
or
Power down the washer, then reapply power.
NOTE: If a service cycle is in progress upon exiting service mode,
the cycle will complete normally with cycle status information
displayed. The display will resume normal customer operation
mode when the cycle ends.
A3, A4,
A5, A6
Extra
Rinse
Soil Level
(Heavy-On,
Normal-Off)
Water
Temp
A3, A4,
A5, A6
Extra
Rinse
Soil Level
(Heavy-On,
Normal-Off)
Water
Temp
00 Off Off Tap
Cold
10 On Off Tap
Cold
01 Off Off Cold 11 On Off Cold
02 Off Off Cool 12 On Off Cool
03 Off Off Warm 13 On Off Warm
04 Off Off Hot 14 On Off Hot
08 Off On Tap
Cold
18 On On Tap
Cold
09 Off On Cold 19 On On Cold
a Off On Cool 1A On On Cool
B Off On Warm 1B On On Warm
C Off On Hot 1C On On Hot
19
MAYTAG
®
COMMERCIAL LAUNDRY
LIMITED WARRANTY
1. All other costs including labor, transportation, shipping, or custom duties for
covered parts.
2. Factory specified replacement parts if this commercial appliance is used for other
than normal, commercial use or when it is used in a manner that is inconsistent to
published user or operator instructions and/or installation instructions.
3. Service calls to correct the installation of your commercial appliance, to instruct
you on how to use your commercial appliance, to replace or repair house fuses,
or to correct external wiring or plumbing.
4. Service calls to repair or replace appliance light bulbs, air filters, or water filters.
Consumable parts are excluded from warranty coverage.
5. Damage resulting from improper handling of product during delivery, theft,
accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,
installation not in accordance with local electrical or plumbing codes, or use of
products not approved by Maytag.
6. Pick up and delivery. This commercial appliance is designed to be repaired on
location.
7. Repairs to parts or systems resulting from unauthorized modifications made to
the commercial appliance.
8. The removal and reinstallation of your commercial appliance if it is installed in an
inaccessible location or is not installed in accordance with published installation
instructions.
9. Damage resulting from exposure to chemicals.
10. Changes to the building, room, or location needed in order to make the
commercial appliance operate correctly.
11. Factory specified replacement parts on commercial appliances with original
model/serial numbers that have been removed, altered, or cannot be easily
determined.
12. Discoloration, rust, or oxidation of stainless steel surfaces.
13. Factory specified replacement parts as a result of incorrect diagnosis or repair
by an “out of network” service company.
The cost of repair or replacement under these excluded circumstances shall
be borne by the customer.
FIVE YEAR LIMITED WARRANTY
(PARTS ONLY — LABOR NOT INCLUDED)
For the first five years from the original date of
purchase, when this commercial appliance is
installed, maintained, and operated according to the
instructions attached to or furnished with the product,
Maytag brand of Whirlpool Corporation (hereafter
“Maytag”) will pay for factory specified replacement
parts to correct defects in materials or workmanship
that existed when this commercial appliance was
purchased. This limited warranty does not include
labor.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS
LIMITED WARRANTY SHALL BE PRODUCT REPAIR
AS PROVIDED HEREIN. Maytag recommends that
you use an “in network” service provider to diagnose
and repair your Commercial Laundry product.
Maytag will not be responsible under this warranty
to provide additional replacement parts as a result of
incorrect diagnosis or repair by an “out of network”
service company. This limited warranty is valid in the
United States or Canada and applies only when the
commercial appliance is used in the country in which
it was purchased. This limited warranty is effective
from the date of the original consumer purchase.
Proof of original purchase date is required to obtain
service under this limited warranty.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO FIVE YEARS OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do
not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. MAYTAG
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or
limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific
legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes
with this major appliance, you should ask Maytag or your retailer about buying an extended warranty.
08/16
IF YOU NEED SERVICE:
Contact your authorized Maytag
®
Commercial Laundry distributor. To locate your authorized Maytag
®
Commercial Laundry distributor,
visit www.MaytagCommercialLaundry.com.
For written correspondence:
Maytag
®
Commercial Laundry Service Department
2000 N M 63
Benton Harbor, Michigan 49022-2632 USA
FIVE YEAR LIMITED WARRANTY
WHAT IS COVERED
WHAT IS NOT COVERED
20
SÉCURITÉ DE LA LAVEUSE
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Maytag Commercial MAT20MNAWW Guide d'installation

Marque
Maytag Commercial
Modèle
MAT20MNAWW
Catégorie
Machines à laver
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents