Shindaiwa HT2510_DH2510T Manuel utilisateur

Catégorie
Taille-haies électriques
Taper
Manuel utilisateur
1????
OPERATOR'S MANUAL
MANUEL D'UTILISATION
BEDIENUNGSANLEITUNG
MANUALE PER L'OPERATORE
HT2510
DH2510T
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR
SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
AVERTISSEMENT
LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RE-GLES DE
SECURITE. LE NON-RESPECT DES REGLES DE SECU-RITE ENTRAINE UN
RISQUE DE BLESSURE GRAVE.
WARNUNG
LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE-
FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS
RISIKO SCHWERER VERLETZUNGEN.
AVVERTENZA
LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LA-VORARE
IN CONDIZIONI DI MASSIMA SICUREZZA. LA MANCA-TA OSSERVANZA
DELLE ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.
2
??
??
1Top cover
ENGLISH
(Original instructions)
OPERATOR'S MANUAL
HEDGE TRIMMER
HT2510
DH2510T
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE
RULES FOR SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
2
Important information
2Important information
Please ensure that you read the operator's manual before using your product.
Intended use of this product
Shindaiwa Hedge Trimmer are lightweight, high-performance, petrol engined units designed for hedge and shrub trim-
ming.
Do not use this unit for any purpose other than aforementioned.
Users of the product
You should not use this product until you have read the operator's manual carefully and fully absorbed its content.
This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a
cold, tiredness or otherwise in poor physical condition, or children.
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-
erty.
About your operator's manual
This manual contains necessary information about the operation and maintenance of your product. Please read it care-
fully and absorb its contents.
Always keep your manual in a place where it is readily accessible.
If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your shindaiwa
dealer.
The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,
and there may be a slight conversion error in some cases.
Loaning or assigning your product
When loaning the product described in this manual to another party, ensure that the person borrowing and working with
the product receives the operator's manual along with the product. If you assign your product to another party, please
enclose the operator's manual with the product when handing it over.
Enquiries
Please contact your shindaiwa dealer for requests regarding information about your product, the purchase of consum-
ables, repairs, and other such enquiries.
Notices
The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the
illustrations used may differ from the product itself in order to make the explanations clearer.
This product requires the assembly of some parts.
Please consult your shindaiwa dealer if anything is unclear or of concern.
Manufacturer
YAMABIKO CORPORATION
7-2 SUEHIROCHO 1-CHOME, OHME, TOKYO 198-8760, JAPAN
Authorized Representative in Europe
Atlantic Bridge Limited
Atlantic House, PO Box 4800, Earley, Reading RG5 4GB, United Kingdom
3
Contents
For safe use of your product...............................................................................................4
Warning notices.............................................................................................................4
Other indicators .............................................................................................................4
Symbols.........................................................................................................................4
Location in which the safety decal is attached...............................................................6
Handling fuel..................................................................................................................7
Handling the engine.......................................................................................................8
Handling the product .....................................................................................................9
Description........................................................................................................................13
Before you start ................................................................................................................15
Assembly.....................................................................................................................15
Throttle lever free play.................................................................................................17
Preparing the fuel ........................................................................................................18
Engine operation...............................................................................................................19
Starting the engine ......................................................................................................19
Stopping the engine.....................................................................................................21
Hedge and shrub trimming operation ...............................................................................22
Rotating operation .......................................................................................................22
Basic hedge trimming operation..................................................................................22
Maintenance and care ......................................................................................................23
Maintenance and care.................................................................................................23
Storage .............................................................................................................................31
Long-term storage (30 days or more)..........................................................................31
Disposal procedure...........................................................................................................32
Specifications....................................................................................................................33
Declaration of conformity..................................................................................................35
4
For safe use of your product
For safe use of your product
Be careful to read this section before using your product.
The precautions described in this section contain important safety information. Please observe them carefully.
You must also read the precautions that appear in the body of the manual itself.
Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.
Warning notices
Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product
itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.
Other indicators
As well as warning notices, this manual uses the following explanatory symbols:
Symbols
In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what
each symbol means.
DANGER WARNING CAUTION
This symbol accompanied by the
word "DANGER" calls attentions to
an act or a condition which will lead to
serious personal injury or death of op-
erators and bystanders.
This symbol accompanied by the
word "WARNING" calls attentions to
an act or a condition which can lead to
serious personal injury or death of op-
erators and bystanders.
"CAUTION" indicates a potentially
hazardous situation which, if not
avoided, may result in minor or mod-
erate injury.
Circle and slash sym-
bol means whatever is
shown is prohibited.
NOTE IMPORTANT
This enclosed message provides tips
for use, care and maintenance of the
product.
Framed text featuring the word "IM-
PORTANT" contains important infor-
mation about the use, checking,
maintenance and storage of the prod-
uct described in this manual.
Symbol form/shape Symbol description/applica-
tion
Symbol form/shape Symbol description/applica-
tion
Carefully read the operator's
manual
Petrol and oil mixture
Wear eyes, ears and head
protection
Purge bulb (Primer)
Safety / Alert
Carburettor adjustment
- Low speed mixture
Finger severing
Carburettor adjustment
- High speed mixture
Emergency stop
Carburettor adjustment
- Idle speed
5
For safe use of your product
Do not use the product in plac-
es with poor ventilation
Choke Control
"Cold Start"
Position
(Choke Closed)
Beware of fire
Choke Control
"Run"
Position
(Choke Open)
Beware of electric shocks
Beware of high-temperature
areas
Guaranteed sound power lev-
el
Engine start
Symbol form/shape Symbol description/applica-
tion
Symbol form/shape Symbol description/applica-
tion
6
For safe use of your product
Location in which the safety decal is attached
The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what
the decal means before using your product.
If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal
from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.
1. Safety decal (Part number X505-003340)
2. Safety decal (Part number X505-003350)
1. Safety decal (Part number X505-002310)
2. Safety decal (Part number X505-003350)
7
For safe use of your product
Handling fuel
DANGER
Always keep well away from fire when refuelling
Fuel is highly inflammable and leads to a risk of fire if mishandled. Use extreme care when mixing, storing or handling
or serious personal injury may result. Be careful to observe the following instructions.
Do not smoke or hold a flame near when refuelling.
Do not fuel up while the engine is hot or in operation.
If you do so, the fuel could ignite and cause fire, leading to burns.
About the container and refuelling place
Use an approved fuel container.
Fuel tanks/cans may be under pressure.
Always loosen fuel caps slowly allowing pressure to
equalize.
DO NOT fill fuel tanks indoors.
ALWAYS fill fuel tanks outdoors over bare ground.
Fuel spills can cause fire
Observe the following precautions when refuelling:
Do not add so much fuel that it reaches the mouth of the
fuel tank. Keep the fuel within the prescribed level (up to
the shoulder level of the fuel tank).
Mop up any fuel that overflows or spills out due to over-
filling.
Tighten the fuel tank cap securely after refuelling.
Fuel spills can cause fire and burns when ignited.
1. Fuel tank
2. Shoulder level
Do not start the engine in the area where you refu-
eled
You must not start the engine in the place where you
carried out the refuelling. Move at least 3m from the
place where you refueled before starting the engine.
Fuel leaks that occur while refuel-
ling can cause fire if ignited.
Fuel leaks cause fire
After refuelling, always check
that there are no leaks or dis-
charges of fuel from the fuel
pipe, fuel system grommets, or
around the fuel tank cap.
If you do find fuel leaks or discharges, stop using the
product immediately and contact your dealer to have it
repaired.
Any fuel leaks could cause fire.
8
For safe use of your product
Handling the engine
WARNING
Starting the engine
Be particularly careful to observe the following precau-
tions when starting the engine:
Always ensure all handles and guards are fitted
Check that none of the nuts and bolts are loose
Check that there are no fuel leaks
Check that the cutter blades is not damaged or exces-
sively worn. If you find any abnormalities, do not use
the product.
Place the product in a flat, well ventilated place
Leave plenty of space around the product and do not al-
low people or animals near it
Remove obstructions, if any
Make sure that the cutter blades is not touching the
ground or any obstacles
Start the engine with the throttle trigger in the idle speed
position
Hold the product firmly to the ground when starting the
engine
Do not start the engine holding the product in the air
Use extreme caution when operating near fences or
electric wiring
Failure to observe the precautions could cause an accident
or injury, or even lead to a fatality.
Once the engine has started, check for abnormal vi-
brations and sounds
Check that there are no abnormal vibrations or sounds
once the engine starts. Do not use the product if there
are abnormal vibrations or sounds. Contact your dealer
to have it repaired.
Accidents involving parts that fall or shatter off can cause
wounds or serious injury.
Do not touch high temperature or high voltage com-
ponents while the product is running
Do not touch the following high temperature or high volt-
age components while the product is running or for some
time after it stops.
Silencer, spark plug, gear housing, and
other high temperature components
You could burn yourself if you touch a high
temperature component.
Spark plug, spark plug wire, and other
high voltage components
You could receive an electric shock if you
touch a high voltage component while the
product is running.
Put safety first in the case of fire or smoke
If fire comes from the engine or smoke appears from
any area other than the exhaust vent, first distance
yourself from the product to ensure your physical safe-
ty.
Use a shovel to throw sand or other such
material on the fire to prevent it from
spreading, or put it out with a fire extin-
guisher.
A panicked reaction could result in the fire and
other damage becoming more extensive.
Exhaust fumes are toxic
The exhaust fumes from the engine contain toxic gases.
Do not operate the product indoors or in a plastic green-
house or in other ill ventilated places.
The exhaust fumes could cause poisoning.
Turn off the engine when checking or maintaining
the product
Observe the following precautions when checking and
maintaining your product after use:
Turn the engine off and do not attempt to check or main-
tain the product until the engine has cooled
You could burn yourself.
Remove the spark plug cap before performing checks
and maintenance
An accident could occur if the product starts unexpectedly.
Checking the spark plug
Observe the following precautions when checking the
spark plug.
If the electrodes or terminals are worn, or if there are
cracks in the ceramics, replace them with new parts.
The spark test (for checking whether the spark plug is
sparking) must be carried out by your dealer.
The spark test must not be carried out in proximity of
the spark plug hole.
The spark test must not be performed in places where
there are fuel spills or inflammable gases
You must not touch the
metal parts of the spark
plug
The spark plug could ig-
nite a fire or give you an
electric shock.
9
For safe use of your product
Handling the product
General precautions
Precautions for use
WARNING
Operator's manual
Be careful to read the operator's manual
properly before using your product in or-
der to ensure correct operation.
Failure to do so could lead to an accident or
serious injury.
Do not use the product for anything
other than its intended purpose
You must not use the product for any purpose other
than those described in the operator's manual.
To do so could lead to an accident or serious injury.
Do not modify the product
You must not modify the product.
To do so could lead to an accident or serious injury. Any
malfunction resulting from a modification to the product will
not be covered by the manufacturer's warranty.
Do not use the product unless it has been checked
and maintained
You must not use the product unless it has been
checked and maintained. Always ensure that the prod-
uct is checked and maintained on a regular basis.
Failure to do so could lead to an accident or serious injury.
Loaning or assigning your product
When loaning your product to another party, ensure
that the person borrowing the product receives the op-
erator's manual along with it.
If you assign your product to another party, please en-
close the operator's manual with the product when
handing it over.
Failure to do so could lead to an accident or serious injury.
Being prepared in case of an injury
In the unlikely event of an accident or injury, please ensure
that you are prepared.
First aid kit
Towels and wipes (to stop any bleeding)
Whistle or mobile phone (for calling outside help)
If you are unable to perform first aid or call for outside help,
the injury could worsen.
DANGER
Starting the engine
Never try to start the engine by positioning yourself on
the blade side.
Physical injury can occur if the cutter blades suddenly starts
to move.
Do not remove the blunt extension
Do not operate the product without the blunt extension.
If it needs to be removed for the sake of maintenance,
consult your dealer.
Failure to comply may result in serious injury.
Always stop the engine when a blades jam occurs
Do not attempt to remove an object causing a blades
jam if the engine is running.
Physical injury can occur if a blades jam is removed and the
blades starts moving.
10
For safe use of your product
WARNING
Users of the product
The product should not be used by:
people who are tired
people who have taken alcohol
people who are on medication
people who are pregnant
people who are in poor physical
condition
people who have not read the op-
erator's manual
children
Failure to observe these instruc-
tions could lead to an accident.
Environment of use and operation
Do not use the product in places where there is no sure
foothold, such as on steep slopes or after rainfall, as
such places are slippery and dangerous.
Do not operate the product at night or in dark places
with poor visibility.
A serious injury could result if you fall or slip, or fail to oper-
ate the product correctly.
Transport of the product
When transporting in the situations described below, turn
off the engine and ensure that the cutter blades has
stopped moving, then fit the blade cover and position the
silencer away from yourself.
Moving to the place where you are working
Moving to another area while you are working
Leaving the place where you have been working
Failure to observe these precautions could cause burns or
serious injury.
When transporting the product by car, empty the fuel
tank, fit the blade cover, and secure the product firmly
in place to prevent it from moving around.
Travelling by car with fuel in the fuel tank could lead to a fire.
Vibration and cold
It is believed that a condition called Raynaud's Phenome-
non which affects the fingers of certain individuals may be
brought about by exposure to vibration and cold. Expo-
sure to vibration and cold may cause tingling and burning,
followed by loss of colour and numbness in the fingers.
The following precautions are strongly recommended be-
cause the minimum exposure which might trigger the ail-
ment is unknown.
Keep your body warm, especially the head and neck,
feet and ankles, and hands and wrists.
Maintain good blood circulation by performing vigorous
arm exercises during frequent work breaks, and also by
not smoking.
Limit the number of hours of operation.
Try to fill each day with jobs where operating the hedge
trimmer or other hand-held power equipment is not re-
quired.
If you experience discomfort redness and swelling of
the fingers, followed by whitening and loss of feeling,
consult your physician before exposing yourself further
to cold and vibration.
Failure to observe these instructions could result in damage
to your health.
Repetitive stress injuries
It is believed that over-using the muscles and tendons of
the fingers, hands, arms and shoulders may cause sore-
ness, swelling, numbness, weakness and extreme pain to
the areas just mentioned. Certain repetitive hand activities
may put you at a high risk for developing a repetitive
stress injury (RSI).
To reduce the risk of RSI, do the following:
Avoid using your wrist in a bent, extended or twisted
position.
Take periodic breaks to minimize repetition and rest
your hands. Reduce the speed and force in which you
do the repetitive movement.
Do exercises to strengthen hand and arm muscles.
See a doctor if you feel tingling, numbness or pain in
your fingers, hands, wrists or arms. The sooner RSI is
diagnosed, the more likely permanent nerve and muscle
damage can be prevented.
Failure to observe these instructions could result in damage
to your health.
11
For safe use of your product
WARNING
Remove foreign objects and obstructions before
working with the product
Inspect area that the product will be used in. Remove
stones, metal objects and any other object that could
jam or damage the product.
An accident or serious injury can occur if foreign objects
throw the cutting device.
Turn off the engine immediately if anything goes
wrong
In the following situations, turn off the engine immediately
and ensure that the cutting device has stopped before
checking each area of the product. Replace any damaged
parts.
If the cutting device hits a rock, tree, post, or other such
obstruction while you work.
If the product suddenly starts to vibrate abnormally.
Continuing to use parts when they are damaged could lead
to an accident or serious injury.
The area within a 10 m radius is a danger zone
The area within a 10 m radius of the product is a danger
zone. Be careful to observe the following precautions
while working with the product.
Do not allow children and other people or pets to enter
the danger zone.
If another person enters the danger zone, turn off the
engine to stop the blades.
When approaching the operator, signal to him by, for
example, throwing twigs from outside the danger zone,
and then check that engine has been switched off and
the blades has stopped moving.
Do not allow anyone to hold the material you are cut-
ting.
Any contact with the cutter blades could cause serious inju-
ry.
Do not use the product when the cutter blades is
moving at idle speed
You must not use the product while the cutter blades is
moving if the Hedge Trimmer is running with the throttle
trigger in the idle speed position. Turn off the engine im-
mediately and adjust the carburettor.
To do so could lead to an accident or serious injury.
Do not operate the product one-handed
Keep both hands on handles while the engine is run-
ning. Never operate the product with only one hand.
Keep a firm grip on the hedge trimmer with both hands,
one hand on the front handle, the other hand on the rear
handle.
Use a firm grip with thumbs and fingers encircling the
handles.
Never remove hands from the product when the blades
are moving.
Failure to observe these instructions will cause the product
to be held unsteadily and could result in serious injury.
Make sure that the cutter blades is stopped before
putting the product on the ground
When you turn off the engine, check to ensure the cutter
blades has stopped moving before you lower the prod-
uct to the ground.
Even if the engine has been turned off, the blades can still
cause an injury while free-wheeling.
Remove debris from the silencer
If objects such as grasses, leaves, twigs or excessive
grease got stuck over the area around the silencer of
the engine, stop the engine and remove them paying at-
tention not to touch hot spots.
Failure to do so could lead to a fire.
12
For safe use of your product
Protective gear
WARNING
Do not use the product to cut hard objects
Do not use the product to cut hard objects such as
wires or steel plates.
If the blades strikes an obstruction or is prevented from
functioning properly, stop the engine and inspect the
blades for damage.
Failure to follow these instructions could cause breakage of
the product or an accident.
Never use the product getting on a ladder or a stool
Do not overreach or stand on unstable surfaces.
Do not use the product when being at the top of the lad-
der or standing on a stool.
Failure to do so could lead to an accident or serious injury.
Stop the engine before rotating operation (DH2510T)
Make sure to stop the engine before rotating the rear
handle. Never rotate the handle without turning off the
engine even when the throttle trigger is in the idle speed
position.
Failure to observe these instructions will cause the product
to be held unsteadily and could result in serious injury.
WARNING
Wear protective gear
Always wear the following protective gear when working
with the hedge trimmer.
a Head protection (helmet): Protects the head
b Ear muffs or ear plugs: Protect the hearing
c Safety goggles: Protect the eyes
d Safety gloves: Protect the hands from cold and vibration
e Work clothes that fit (long sleeves, long trousers): Pro-
tect the body
f Heavy duty, non-slip protective boots or non-slip work
shoes : Protect the feet
Failure to observe these precautions could result in damage
to your sight or hearing, or lead to a serious injury.
When necessary, please use the protective gear below.
Dust mask: Protects the breathing apparatus
Bee net: To deal with attacks by bees
Wear proper clothing
Do not wear ties, jewellery, or loose, dangling clothing which could be
caught in the unit. Do not wear open toed footwear, or go bare-foot or
barelegged.
Failure to observe these precautions could result in damage to your sight or
hearing, or lead to a serious injury.
13
Description
Description
1. Cutter
2. Guide bar
3. Front handle
4. Starter handle
5. Rear handle
6. Throttle trigger
7. Silencer cover
8. Protector
9. Ignition (STOP) switch
10. Throttle trigger lockout
11. Fuel tank cap
12. Choke
13. Blade cover
14. Fuel tank
15. Gearcase
16. Air cleaner cover
14
Description
1. Cutter
2. Front handle
3. Starter handle
4. Ignition (STOP) switch
5. Throttle trigger lockout
6. Rear handle
7. Twist handle release lever
8. Throttle trigger
9. Silencer cover
10. Fuel tank cap
11. Choke
12. Blade cover
13. Fuel tank
14. Gearcase
15. Air cleaner cover
16. Protector
15
Before you start
Before yo u start
Assembly
Prior to Assembly
Before assembling this product, please make sure you have all
the components required for a complete unit:
Engine assembly (powerhead)
Cutter and gearcase assembly
Rear handle
Front handle
Bolt package
Clip
Tool kit including, allen wrenches, combination spark plug and
spanner wrench.
Carefully inspect all components for damage.
Assembly HT2510
Attaching the rear handle to the gearcase
1. Temporarily remove the M5×12 mm index bolt.
2. Loosen, but do not remove, the M5×25 mm clamp screw.
3. Position the rear handle assembly as shown. Starting from
the rear of the trimmer, push the throttle cable, ignition wire,
and ground wire through the handle mounting bracket.
4. Slide the rear handle into the handle mounting bracket until
it bottoms. Use care to avoid pinching or otherwise damag-
ing the wires and cable.
Align the hole in the rear handle with the matching hole in
the handle mounting bracket, and then install and firmly
tighten the M5×12 mm index bolt.
Tighten the M5×25 mm clamp screw firmly.
Installing the powerhead on the gearcase
Orient the gearcase assembly to the powerhead as shown,
and secure with the three M6×16 mm screws.
1. Securely tighten screws A and B.
2. Push screw C through the eye terminal in the throttle control
ground wire, and then install and firmly tighten the screw to
the powerhead.
1. Rear handle assembly
2. Clamp screw
3. Index bolt
4. Throttle cable, ignition, and ground wires
1. Powerhead
2. Screws A and B
3. Screw C
16
Before you start
Install the front handle
The front handle is installed over a 5 mm bolt on the guide bar.
1. Install the 5 mm flange nut over the bolt on the guide bar, and
then tighten the nut firmly.
Connect the throttle cable
Connect the throttle cable
1. Loosen the unscrew fasteners and remove the air cleaner
cover.
2. Slip the throttle cable into the cable adjuster and hook the
bullet end of the cable onto the swivel. Fix the clip to the ca-
ble swivel.
Connect the ignition leads
1. Connect the ignition wires by pushing the bullet connectors
together.
2. Reinstall the air cleaner cover.
1. 5 mm flange nut
2. Front handle
3. Bolt
WARNING
Incorrect assembly could expose the operator to seri-
ous injury. Read and follow assembly instructions care-
fully.
1. Air cleaner cover
2. Unscrew Fasteners
1. Throttle cable
2. Cable adjuster
3. Cable swivel
4. Clip
1. Ignition lead
CAUTION
Routing of wiring must not interfere with throttle or
choke operation.
17
Before you start
Throttle lever free play
If the unit does not return to idle speed or reach full rpm, the throt-
tle lever free play may need to be adjusted as follows:
1. Measure free play at the end of the throttle lever. Throttle le-
ver free play should be approximately 5-7 mm.
2. If adjustment is necessary, remove the air cleaner cover.
Loosen the cable adjuster lock nut and turn the cable adjust-
ment fitting in or out until throttle lever free play is approxi-
mately 5-7 mm.
3. Replace the air cleaner cover, and tighten the unscrew fas-
teners securely.
1. Throttle cable adjuster lock nut
2. Throttle cable adjuster
3. Throttle cable
18
Before you start
Preparing the fuel
Fuel
Fuel is a mixture of regular grade petrol and an air-cooled 2-
stroke engine oil of reputable brand name.
Minimum 89 Octane unleaded petrol is recommended. Do not
use fuel containing methyl alcohol or more than 10 % of ethyl
alcohol.
Recommended mixture ratio; 50 : 1 (2 %) for ISO-L-EGD
Standard (ISO/CD 13738), JASO FC, FD grade and Shindai-
wa One 50 : 1 oil.
- Do not mix directly in engine fuel tank.
- Avoid spilling petrol or oil. Spilled fuel should always be
wiped up.
- Handle petrol with care, it is highly inflammable.
- Always store fuel in approved container.
Fuel supply
Always refuel in a well ventilated location. Do not pour fuel in-
doors.
Place the product and the refuelling tank on the ground when
performing the refuelling operation. Do not refuel the product
on the loading platform of a truck, or in other such places.
Always ensure that the fuel level remains below the shoulder
level of the fuel tank when refuelling.
There is a difference in pressure between the fuel tank and the
outside air. When refuelling, loosen the fuel tank cap slightly to
eliminate the difference in pressure.
Always wipe up any fuel spills.
Move at least 3m away from where you refueled before you
start the engine.
Keep the refuelling tank in a shaded area away from fire.
DANGER
Fuel is highly inflammable and there is a risk of fire if it is handled incorrectly. Carefully read
and observe the precautions in the section of this manual titled "For safe use of your prod-
uct".
Once the refuelling is complete, securely tighten the fuel tank cap and do not forget to
check that there are no leaks or discharges of fuel from the fuel pipe, fuel system grommets,
or around the fuel tank cap. If you do find fuel leaks or discharges, stop using the product
immediately and contact your dealer to have it repaired.
If the fuel ignites, it could cause burns and fire.
CAUTION
There is difference in pressure between the fuel tank and the outside air. When refuelling, loosen the fuel tank cap
slightly to eliminate the difference in pressure.
Otherwise, fuel may get spewed.
NOTE
Stored fuel ages. Do not mix more fuel than you expect use in thirty (30) days. Do not mix directly in fuel tank.
1. Fuel tank 2. Shoulder level
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160

Shindaiwa HT2510_DH2510T Manuel utilisateur

Catégorie
Taille-haies électriques
Taper
Manuel utilisateur