Specifications are subject to change without notice.
© 2022 VTech Communications, Inc. |
© 2022 VTech Technologies Canada Ltd.
All rights reserved. 09/22. IS8121-X | IS8122-X_QSG_V4
Technical specifications
Frequency
control Crystal controlled PLL synthesizer
Transmit
frequency Handset: 1921.536-1928.448 MHz
Telephone base: 1921.536-1928.448 MHz
Channels DECT channel: 5
Nominal
effective
range
Maximum power allowed by FCC and IC.
Actual operating range may vary according to
environmental conditions at the time of use.
Power
requirement
Handset: 2.4 VDC, AAA x 2, Ni-MH battery
Telephone base: 6V DC @ 0.4A
Charger: 6V DC @ 0.4A
Memory Phonebook: 1000 memory locations;
up to 30 digits and 15 characters
Caller ID log: 50 memory locations;
up to 24 digits and 15 characters
Call block: 1000 entries
Go to www.vtechphones.com (US)
to register your product for enhanced
warranty support and latest VTech
product news.
Go to phones.vtechcanada.com (CA)
for latest VTech product news.
Quick start guide
IS8121
IS8121-2
IS8121-3
IS8121-4
IS8121-5
IS8122-3
IS8122-4
DECT 6.0 Cordless telephone
with BLUETOOTH® wireless technology
Phonebook
The phonebook can store up to 1000 entries, which are shared
by all handsets. Each entry may consist of a telephone number
up to 30 digits, and a name up to 15 characters.
Add a phonebook entry
Review phonebook entries
Delete a phonebook entry
When your desired phonebook entry displays:
Caller ID
If you subscribe to caller ID service, information about each
caller appears after the first or second ring.
The caller ID log stores up to 50 entries. Each entry has up
to 24 digits for the phone number and 15 characters for the
name.
Review caller ID log entries
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing aids and
cochlear implants. The TIA-1083 Compliant Logo is a trademark of
the Telecommunications Industry Association. Used under license.
T
Compatible with
Hearing Ai
d T-Coil
TIA-1083
The ENERGY STAR® program (www.energystar.gov) recognizes and
encourages the use of products that save energy and help protect our
environment. We are proud to mark this product with the ENERGY
STAR® label indicating it meets the latest energy efficiency guidelines.
Volume
Press
- OR -
Put the handset
in the telephone
base or charger
End a home call
Answer a home call
Make a home call
1
Press
- OR -
2
Enter the phone number.
ECO
HANDSET
10:15pm 12/25 10:15pm 12/25
595-9511_
ECO
Enter number
595-9511_
ECO
Enter name
ECO
Mike Smith
ECO
ECO
HANDSET
10:15pm 12/25
Mike Smith
800-595-9511
ECO
Mike Smith
800-595-9511
ECO
Delete entry ?
ECO
ECO
HANDSET
10:15pm 12/25
Dial a caller ID log entry
When your
desired caller ID
entry displays
on the handset
screen:
Press - OR - - OR -
Save a caller ID log entry to the phonebook
Delete a caller ID log entry
When your
desired caller ID
entry displays
on the handset
screen:
When your
desired caller ID
entry displays
on the handset
screen:
Press
ECO
Mike Smith
595-9511
NEW
09:05pm 12/25
ECO
Mike Smith
595-9511
NEW
09:05pm 12/25
ECO
Mike Smith
595-9511
NEW
09:05pm 12/25
>To Phonebook
ECO
Enter number
800-595-9511_
ECO
Mike Smith_
ECO
Important safety instructions
When using your telephone equipment, basic
safety precautions should always be followed
to reduce the risk of fire, electric shock and
injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked
on the product.
3. CAUTION: Do not install the telephone base
at a height above 2 meters.
4. Unplug this product from the wall outlet
before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.
5. Do not use this product near water such as
near a bath tub, wash bowl, kitchen sink,
laundry tub or a swimming pool, nor in a wet
basement or shower.
6. Do not place this product on an unstable
table, shelf, stand or other unstable surfaces.
7. Avoid placing the telephone system in
places with extreme temperature, direct
sunlight, or other electrical devices. Protect
your phone from moisture, dust, corrosive
liquids and fumes.
8. Slots and openings in the back or bottom
of the telephone base and handset are
provided for ventilation. To protect them
from overheating, these openings must not
be blocked by placing the product on a
soft surface such as a bed, sofa or rug. This
product should never be placed near or over
a radiator or heat register. This product should
not be placed in any area where proper
ventilation is not provided.
9. This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply in your home or office,
consult your dealer or local power company.
10. Do not allow anything to rest on the power
cord. Do not install this product where the
cord may be walked on.
11. Never push objects of any kind into this
product through the slots in the telephone
base or handset because they may touch
dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the
product.
12. To reduce the risk of electric shock, do not
disassemble this product, but take it to
an authorized service facility. Opening or
removing parts of the telephone base or
handset other than specified access doors
may expose you to dangerous voltages
or other risks. Incorrect reassembling can
cause electric shock when the product is
subsequently used.
13. Do not overload wall outlets and extension
cords.
14. Unplug this product from the wall outlet and
refer servicing to an authorized service facility
under the following conditions:
• When the power supply cord or plug is
damaged or frayed.
• If liquid has been spilled onto the
product.
• If the product has been exposed to rain
or water.
• If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered
by the operation instructions. Improper
adjustment of other controls may result
in damage and often requires extensive
work by an authorized technician to
restore the product to normal operation.
• If the product has been dropped and
the telephone base and/or handset has
been damaged.
• If the product exhibits a distinct change
in performance.
15. Avoid using a telephone (other than cordless)
during an electrical storm. There is a remote
risk of electric shock from lightning.
16. Do not use the telephone to report a gas
leak in the vicinity of the leak. Under certain
circumstances, a spark may be created when
the adapter is plugged into the power
outlet, or when the handset is replaced in
its cradle. This is a common event associated
with the closing of any electrical circuit.
The user should not plug the phone into a
power outlet, and should not put a charged
handset into the cradle, if the phone is
located in an environment containing
concentrations of flammable or flame-
supporting gases, unless there is adequate
ventilation. A spark in such an environment
could create a fire or explosion. Such
environments might include: medical use
of oxygen without adequate ventilation;
industrial gases (cleaning solvents; gasoline
vapors; etc.); a leak of natural gas; etc.
17. Only put the handset of your telephone next
to your ear when it is in normal talk mode.
18. The power adapter is intended to be
correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold
the plug in place if it is plugged into a ceiling,
under-the-table or cabinet outlet.
19. For pluggable equipment, the socket-outlet
shall be installed near the equipment and shall
be easily accessible.
20. CAUTION: Use only the batteries
indicated in this manual. There may be a risk
of explosion if a wrong type of battery is
used for the handset. Use only the supplied
rechargeable batteries or replacement
batteries (BT162342/BT262342) for the
handset. Do not dispose of batteries in a
fire. They may explode.
• Do not use the battery in following
conditions:
» High or low extreme temperature
during use, storage or
transportation.
» Replacement of a battery with an
incorrect type that can defeat a
safeguard.
» Disposal of a battery into fire or a
hot oven, or mechanically crushing
or cutting of a battery, that can
result in an explosion.
» Leaving a batteryin an extremely
high temperature surrounding
environment that can result in
an explosion or the leakage of
flammable liquid or gas.
» A battery subjected to extremely
low air pressure that can result in
an explosion or the leakage of
flammable liquid or gas.
21. Use only the adapter included with this
product. Incorrect adapter polarity or
voltage can seriously damage the product.
22. The applied nameplate is located at the
bottom or near of the product.
SAVE THESE INSTRUCTIONS
Battery
• Use only the battery provided or equivalent.
To order a replacement, visit our website at
www.vtechphones.com or call 1 (800) 595-
9511. In Canada, go to phones.vtechcanada.
com or call 1 (800) 267-7377.
• Do not dispose of the battery in a fire. Check
with local waste management codes for
special disposal instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns
or injury to the eyes or skin. The electrolyte
may be toxic if swallowed.
• Exercise care in handling batteries in order
not to create a short circuit with conductive
materials.
• Charge the battery provided with this
product only in accordance with the
instructions and limitations specified in this
manual.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital
cordless telephones):
Wireless Technology Research, LLC (WTR),
an independent research entity, led a
multidisciplinary evaluation of the interference
between portable wireless telephones and
implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR
recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six
inches from the pacemaker.
• Should NOT place wireless telephones
directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
• Should use the wireless telephone at the
ear opposite the pacemaker.
WTR’s evaluation did not identify any risk
to bystanders with pacemakers from other
persons using wireless telephones.
About cordless
telephones
• Privacy: The same features that make a
cordless telephone convenient create
some limitations. Telephone calls are
transmitted between the telephone
base and the cordless handset by radio
waves, so there is a possibility that the
cordless telephone conversations could be
intercepted by radio receiving equipment
within range of the cordless handset. For
this reason, you should not think of cordless
telephone conversations as being as
private as those on corded telephones.
• Electrical power: The telephone base of
this cordless telephone must be connected
to a working electrical outlet. The electrical
outlet should not be controlled by a wall
switch. Calls cannot be made from the
cordless handset if the telephone base is
unplugged, switched off or if the electrical
power is interrupted.
• Potential TV interference: Some cordless
telephones operate at frequencies that may
cause interference to televisions and VCRs.
To minimize or prevent such interference,
do not place the telephone base of the
cordless telephone near or on top of a
TV or VCR. If interference is experienced,
moving the cordless telephone farther
away from the TV or VCR often reduces or
eliminates the interference.
• Rechargeable batteries: Exercise care in
handling batteries in order not to create a
short circuit with conducting material such
as rings, bracelets and keys. The battery or
conductor may overheat and cause harm.
Observe proper polarity between the
battery and the battery charger.
• Nickel-metal hydride rechargeable
batteries: Dispose of these batteries in a
safe manner. Do not burn or puncture the
battery. Like other batteries of this type, if
burned or punctured, they could release
caustic material which could cause injury.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR2035
Quick
start
guide
1 set for IS8121
2 sets for IS8121-2
3 sets for IS8121-3
3 sets for IS8122-3
4 sets for IS8121-4
4 sets for IS8122-4
5 sets for IS8121-5
1 set for IS8121-2
2 sets for IS8121-3
2 sets for IS8122-3
3 sets for IS8121-4
3 sets for IS8122-4
4 sets for IS8121-5
Introducing
Smart call
blocker
What’s in the box
Connect the telephone base
If you subscribe to
digital subscriber
line (DSL) high-
speed Internet
service through
your telephone
line, make sure
you connect a
DSL filter (not
included) to the
telephone wall
jack.
Install the battery
Connect the charger
Charge the battery
12 hrs
Display
The battery is low and needs
charging.
The battery is charging.
The battery is fully charged.
Handset ringer is off.
New voicemail received from your
telephone service provider.
NEW
There are new caller ID log entries.
ANS ON Answering system is on.
MSG#
5/10 Number of new/old messages
recorded.
ECO The ECO mode activates automatically
to reduce power consumption when
the handset is within range of the
telephone base.
HANDSET
ECO
NEW
ANS ON
10:15
pm
MSG#
5/10
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR2035
THIS SIDE UP
P / CE CÔTÉ VERS LE HAUT
oc-piles :
3342 (2.4V 400mAh Ni-MH)
VERTISSEMENT :
RPUNCTURE BATTERIES.
UPERCER LES PILES.
chine CR1535
After you install your telephone or power returns following a
power outage and battery depletion, the handset will prompt
you to set the date and time, and to configure the Smart call
blocker* and answering system through voice guide.
When the handset
prompts you to set
the date and time
Date and time
Follow the steps below to set the date and time. For example,
if the date is 25 December, 2019, and the time is 10:59 AM:
Date: MM/DD/YY
ECO
Date: 12/2?/YY
ECO
Date: 12/25/19
ECO
Time: 1?:MM --
ECO
Time: 10:59 AM
ECO
1
Enter the date.
2Press SELECT.
3Enter the time. 4Press SELECT.
Voice guide for Smart call blocker
After setting the date and time, the handset will prompt if you
want to set Smart call blocker. For more details, see Use voice
guide to set Smart call blocker in the Introducing Smart call
blocker leaflet.
Setup your Smart call blocker by
inputting the designated numbers as
instructed in the voice guide.
“Hello! This voice guide will assist
you with the basic setup of Smart
call blocker“
When the handset prompts you to set up the Smart call blocker via
voice guide
Smart call blk?
ECO
Press SELECT.
Voice guide for answering system
After setting the Smart call blocker, the handset will display
Voice guide to set up Answering system?
This feature assists you to do the basic setup of the answering
system. You can follow the voice guide to record your own
announcement, set the number of rings and the message alert
tone.
When the handset prompts you to set up the answering system via
voice guide
set up Ans sys?
ECO
Press SELECT.
Setup your answering system by
inputting the designated numbers
as instructed in the voice guide.
“This voice guide will assist you with
the basic setup of your answering
system“
Connect and install
1
Setup
2
Make a cell call
1 Press .
Answer a cell call
- OR - - OR -
Press any
dialing
keys
- OR - - OR -
Press any
dialing
keys
End a cell call
Press
- OR -
Put the handset
in the telephone
base or charger
Press
*Includes licenced QaltelTM technology.
QaltelTM is a trademark of Truecall Group Limited.
LCD language setting
If you accidentally set the LCD language to Spanish or French, press MENU and then enter 364# to change the handset LCD
language back to English while the handset is not in use.
1
Enter the phone
number. 2
Press MENU.
3
Press SELECT.
4
Enter the name.
5
Press SELECT.
1
Press , then the
number of entries
displays.
2
Press / to
browse the entries.
1
Press DELETE.
2
Press SELECT.
Phonebook
Basic operation Caller ID
2
Press / to select a device,
then press MENU/SELECT.
3 Enter the phone number. Mike Smith
800-595-9611
ECO
Dial a phonebook entry
When your desired phonebook entry displays:
Mike Smith
800-595-9511
ECO
Press
- OR - - OR -
1
Press CID.
2
Press / to
browse the entries.
1
Press MENU.2Press SELECT to
select To
Phonebook.
3Edit the number
if needed, then
press SELECT.
4Edit the name
if needed, then
press SELECT.
09:05pm 12/25
Mike Smith
595-9511
ECO
Deleting...
ECO
Press
Press
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use
of such marks by VTech Holdings Limited is under license. VTech Holdings Limited is
a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their
respective owners.
Press again to dial.
4
Scan the QR code for
support information
Follow the steps to
set the date and time
if you skipped the
prompt.
Press / to
scroll to Set date/time,
then press SELECT.
2
Press MENU.
1
Enter the date, then
press SELECT.
3
Enter the time, then
press SELECT.
4
HANDSET 1
ECO
10:30PM 11/20
Set date/time
ECO
Date: 12/25/19
ECO
Time: 10:59 AM
ECO
Improve the telephone signal
strength
NOTESNOTE
Note
• To avoid interference, place the
telephone base in a central location of
the house and at least 3 feet (1 meter)
away from thick walls as well as other
household appliances such as, TV,
radio, microwave oven, Wi-Fi router,
large mirror, metal furniture and fish
tank.
> 1 m (3 feet)
> 1 m (3 feet)
> 1 m (3 feet)
(3(3
ff
ee
tt
etet
etet
etet
etet
))
))
))
TV
See Mount the telephone base (optional) online for the
wall mounting instructions.
Tip
US CA
You can pair and connect your cordless telephone with Bluetooth enabled cellular phones. Before you begin, make sure that you have cellular coverage and your Bluetooth enabled cell phone is not
connected to any other Bluetooth device.
Add a cell phone
1. Press and hold CELL 1 or CELL 2 on the telephone base
for about four seconds until the CELL 1 or CELL 2 light
flashes.
2. Turn on the Bluetooth feature of your cell phone and
search for or add new devices.
3. Once your cell phone finds your telephone
(VTech DECT 6.0), press the appropriate key on your cell
phone to continue the pairing process.
4. When a device is successfully paired and connected, the
corresponding status icon (CELL 1 or CELL 2) displays.
The corresponding device light on the telephone base
turns on.
Add a headset Activate remote voice control
1. Press VOICE on the handset.
2. The handset then shows the remote voice control icon .
3. Speak toward the handset and wait for feedback.
4. Press on the handset to end the current remote
voice control session.
Download a cell phone directory
Before downloading a directory, make sure the cell phone is
paired, active, and connected to your IS8121/IS8121-2/IS8121-3/
IS8121-4/IS8121-5.
About the built-in answering system and voicemail service
For message recording, your telephone has a built-in answering system, and it also supports voicemail
service offered by your telephone service provider (subscription is required, and fee may apply).
Built-in answering system VS Voicemail service
Built-in answering system Voicemail service
Supported by Telephone system Telephone service provider
Subscription No Yes
Fees No May apply
Answer incoming calls • After 3 rings by default.
• It can be changed in the handset menu.
• Usually after 2 rings.
• It can be changed by contacting your
telephone service provider.
Storage Telephone- base Server or System
Display new messages • Handset - XX New Msg
• Telephone base - XX New Msg • Handset - and New voicemail
Retrieve messages
• Press on the telephone base; OR
• Press MENU, and then select Play
messages on the handset; OR
• Access remotely with an access code.
• Press on the dialpad, and enter an
access number and/or passcode from
your telephone service provider.
HANDSET
ECO 1
2
10:30PM 11/20
ECO
Bluetooth
ECO
Need help?
For operations and guides to help you use your telephone, and for latest
information and supports, go and check the online help topics and online FAQs.
Use your smartphone or mobile device to access our online help.
• Go to https://help.vtechphones.com/is8121;
https://help.vtechphones.com/is8122 OR
• Scan the QR code on the right. Launch the camera app or QR code
scanner app on your smartphone or tablet. Hold the device’s camera
up to the QR code and frame it. Tap the notification to trigger the
redirection of the online help.
- If the QR code is not clearly displayed, adjust your camera’s focus by
moving your device closer or further away until it is clear.
You can also call our Customer Support at 1 (800) 595-9511 [in US] or
1 (800) 267-7377 [in Canada] for help.
Answering system
Bluetooth For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de
blessures corporelles ou d’électrocution,
suivez toujours ces mesures préventives de
base lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les
instructions.
2. Observez toutes les instructions et mises
en garde inscrites sur l’appareil.
3. ATTENTION: Ne pas installer le socle
téléphonique à une hauteur supérieure
à 2 mètres.
4. Débranchez ce téléphone de la prise
murale avant de le nettoyer. N’utilisez
pas de nettoyeurs liquides ni en
aérosol. N’utilisez qu’un chiffon doux et
légèrement humecté.
5. N’utilisez pas ce produit près de l’eau,
tel que près d’un bain, d’un lavabo, d’un
évier de cuisine, d’un bac de lavage
ou d’une piscine, ou dans un sous-sol
humide ou sous la douche.
6. Ne déposez pas ce téléphone sur un
chariot, support ou table chancelants.
L’appareil pourrait tomber et être
sérieusement endommagé.
7. Évitez d’installer le système
téléphonique dans les endroits
soumis à une température extrême,
à la lumière directe du soleil ou
à proximité immédiate d’autres
appareils électriques ou électroniques.
Protégez votre téléphone contre les
sources d’humidité, la poussière, les
vapeurs et les liquides corrosifs.
8. Le boîtier de l’appareil est doté de fentes
et d’ouvertures d’aération situées à
l’arrière ou en dessous. Afin d’empêcher
la surchauffe, ces ouvertures ne doivent
pas être obstruées en plaçant l’appareil
sur un lit, divan, tapis ou autre surface
similaires. Ne placez pas cet appareil à
proximité d’un élément de chauffage
ni d’une plinthe électrique. De plus, ne
l’installez pas dans une unité murale ou
un cabinet fermé qui ne possède pas
d’aération adéquate.
9. Ne faites fonctionner cet appareil
qu’avec le type d’alimentation indiqué
sur les étiquettes de l’appareil. Si vous
ne connaissez pas le voltage de votre
maison, consultez votre marchand ou
votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon
d’alimentation. Installez cet appareil
dans un endroit sécuritaire, là où
personne ne pourra trébucher sur
la ligne d’alimentation ni le cordon
téléphonique modulaire.
11. N’insérez jamais d’objets à travers les
fentes et ouvertures de cet appareil,
car ils pourraient toucher à des points
de tension dangereux ou court-circuiter
des pièces, ce qui constituerait un
risque d’incendie ou d’électrocution.
N’échappez pas de liquides dans
l’appareil.
12. Afin de réduire les risques
d’électrocution, ne démontez pas
l’appareil, mais apportez-le plutôt
à un centre de service qualifié s’il
doit être réparé. En enlevant le
couvercle, vous vous exposez à des
tensions dangereuses ou autres
dangers similaires. Un remontage
inadéquat peut être à l’origine d’une
électrocution lors d’une utilisation
ultérieure de l’appareil. Débranchez
l’appareil avant de procéder au
nettoyage. Utilisez un chiffon humide
et doux.
13. Ne surchargez pas les prises de courant
et les rallonges.
14. Débranchez cet appareil de la prise
de courant et communiquez avec le
département de service à la clientèle
de VTech dans les cas suivants :
• Lorsque le cordon d’alimentation est
endommagé ou écorché.
• Si du liquide a été échappé dans
l’appareil.
• Si l’appareil a été exposé à une source
d’humidité telle que la pluie ou l’eau.
• Si le produit ne fonctionne pas
normalement en respectant les
instructions de fonctionnement.
Réglez uniquement les commandes
indiquées dans le les instructions
de fonctionnement. Les réglages
incorrects des autres commandes
pourraient provoquer un dommage
qui pourrait exiger un travail exhaustif
de la part d’un technicien autorisé
afin de rétablir le fonctionnement
normal de l’appareil.
• Si le produit a été échappé et que
le socle et/ou le combiné a été
endommagé.
• Si le produit affiche une nette
diminution de sa performance.
15. Évitez d’utiliser un téléphone (autre
qu’un sans fil) pendant un orage. Les
éclairs peuvent être à l’origine d’une
électrocution.
16. N’utilisez pas le téléphone pour
rapporter une fuite de gaz à proximité
de la fuite. En certaines circonstances,
une flammèche pourrait être
provoquée lorsque l’adaptateur est
branché à une prise de courant, ou
lorsque le combiné est déposé sur le
socle. Ceci est un événement commun
associé à la fermeture d’un circuit
électrique. L’utilisateur ne devrait
pas brancher le téléphone à une
prise de courant, et ne devrait pas
déposer le combiné chargé sur le
socle, si le téléphone se trouve à
proximité d’un endroit comportant des
concentrations de gaz inflammables, à
moins que la ventilation soit adéquate.
Une flammèche dans un tel endroit
pourrait provoquer un incendie ou
une explosion. De tels environnements
peuvent comprendre: des endroits
où l’on utilise de l’oxygène médical
sans ventilation adéquate; des gaz
industriels (dissolvants de nettoyage,
des vapeurs d’essence, etc.); une fuite
de gaz naturel, etc.
17. Ne placez que le combiné de votre
téléphone près de votre oreille
lorsqu’en mode de conversation.
18. Ces adaptateurs ont été conçus pour
être orientés en position verticale ou
montés au sol. Les broches ne sont pas
conçues pour maintenir l’adaptateur en
place si celui-ci est barnché dans une
prise au plafond ou sous une table/
armoire.
19. Pour le MATERIEL RACCORDE PAR
PRISE DE COURANT, le socle de prise de
courant doit etre installe a proximite du
materiel et doit etre aisement accessible.
20. MISE EN GARDE: Il peut y
avoir un risque d’explosion si vous
utilisez le mauvais type de piles pour le
téléphone. N’utilisez que les piles
rechargeable inclus ou les piles de
rechange (BT162342/BT262342).
N’incinérez pas les piles. Celles-ci
risqueraient d’exploser.
• Évite d’utiliser la batterie dans les
conditions suivantes:
»des températures extrêmes
faibles ou élevées auxquelles
une batterie peut être soumise
pendant l’utilisation, le stockage ou
le transport;
»Remplacement d’une batterie
par un type incorrect pouvant
supprimer une protection;
»mise au rebut d’une batterie dans
un feu ou dans un four chaud, ou
écrasement mécanique ou coupure
d’une batterie, susceptible de
provoquer une explosion;
»maintien d’une batterie dans
un environnement à très haute
température pouvant provoquer
une explosion ou la fuite de liquide
ou de gaz inflammables;
»batterie soumise à une pression de
l’air extrêmement faible pouvant
provoquer une explosion ou la fuite
de liquide ou de gaz inflammables.
21. N’utilisez que les adaptateurs inclus
avec ce produit. L’utilisation d’un
adaptateur dont la polarité ou la
tension serait inadéquate risque
d’endommager sérieusement le
produit et mettre votre sécurité en
péril.
22. La plaque signalétique appliquée est
située au bas ou à proximité du produit.
CONSERVEZ CES INSTRUCTIONS
Pile
• N’utilisez que la pile incluse ou
l’équivalent. Pour commander une pile
de recharge, visitez notre site Web au
www.vtechphones.com ou composez
le 800-595-9511. Au Canada, visitez
le phones.vtechcanada.com ou
composez le 800-267-7377.
• Ne jetez pas la pile au feu. Vérifiez les
instructions spécifiques de mise aux
rebus auprès des autorités locales.
• N’ouvrez pas et ne mutilez pas la pile.
L’électrolyte qui s’en échapperait est
corrosif et pourrait causer des brûlures
ou des blessures aux yeux ou à la
peau. L’électrolyte est toxique si avalé.
• Soyez prudents lorsque vous
manipulez les piles afin d’éviter les
courts-circuits provoqués par des
matériaux conducteurs.
• Rechargez la pile incluse avec cet
appareil, selon les instructions et
limites spécifiées dans ce guide
d’utilisation.
Stimulateurs cardiaques implantés dans
l’organisme
Les simulateurs cardiaques (s’applique
uniquement aux téléphones numériques
sans fil) :
L’organisme ‘Wireless Technology
Research, LLC (WTR)’, une firme de
recherche indépendante, a mené
une évaluation pluridisciplinaire des
interférences entre les téléphones sans
fil portatifs et les stimulateurs cardiaques
implantés dans l’organisme. Appuyée par
l’Administration des aliments et drogues
(FDA) des États-Unis, la firme WTR
recommande aux médecins :
Avis aux détenteurs de stimulateurs
cardiaques
• Ils doivent tenir le téléphone sans fil à
une distance d’au moins six pouces du
stimulateur cardiaque.
• Ils ne doivent PAS placer le téléphone
sans fil directement sur le stimulateur
cardiaque, tel que dans une poche
de chemise, lorsque celui-ci est en
marche.
• Ils doivent utiliser le téléphone sans
fil en l’appuyant sur l’oreille qui se
trouve dans la direction opposée au
stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a
pas identifié de risque pour les détenteurs
de simulateurs cardiaques causés par les
gens qui utilisent un téléphone sans fil à
proximité de ceux-ci.
À propos des téléphones sans fil
Confidentialité : Les mêmes
caractéristiques qui constituent des
avantages pour les téléphones sans fil
affichent également des restrictions.
Les appels téléphoniques sont transmis
entre le combiné sans fil et le socle
par le biais d’ondes radio ; il y a donc
la possibilité que vos conversations
téléphoniques sans fil soient interceptées
par des équipements de réception radio
se trouvant dans la portée du combiné
sans fil. Pour cette raison, vous ne devez
pas percevoir les communications
téléphoniques sans fil comme étant aussi
confidentielles que celles des téléphones
à cordons.
Alimentation électrique : Le socle de ce
téléphone sans fil doit être branché à une
prise électrique fonctionnelle. La prise
électrique ne doit pas être contrôlée
par un interrupteur mural. Les appels ne
pourront pas être effectués du combiné
sans fil si le socle est débranché ou mis
hors tension ou si le courant est coupé.
Possibilité d’interférences aux téléviseurs
: Certains téléphones sans fil fonctionnent
sur des fréquences pouvant causer des
interférences aux téléviseurs et aux
magnétoscopes. Pour réduire ou prévenir
de telles interférences, ne placez pas le
socle du téléphone sans fil près ou sur
un téléviseur ou magnétoscope. S’il y
a présence de parasites, il est conseillé
d’éloigner le téléphone sans fil du
téléviseur ou du magnétoscope afin de
réduire possiblement les interférences.
Piles rechargeables : Manipulez les piles
avec soin afin de ne pas les court-circuiter
avec des bagues, bracelets ou clés. Les
piles ou le conducteur peut surchauffer et
causer des blessures. Respectez la polarité
adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure
métallique de nickel : Jetez ces blocs-piles
de manière écologique et sécuritaire.
Ne les incinérez pas et ne les percez pas.
Tel que les autres piles de ce type, elles
pourraient dégager une matière toxique
qui peut causer des blessures corporelles
si elles sont brûlées ou percées.
The RBRC® seal
The RBRC seal on the nickel-metal hydride battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program to
collect and recycle these batteries at the end of their useful lives, when
taken out of service within the United States and Canada.
The RBRC program provides a convenient alternative to placing used
nickel-metal hydride batteries into the trash or municipal waste, which
may be illegal in your area.
VTech’s participation in RBRC makes it easy for you to drop off the spent battery at local
retailers participating in the RBRC program or at authorized VTech product service
centers. Please call 1 (800) 8 BATTERY® for information on Ni-MH battery recycling and
disposal bans/restrictions in your area. VTech’s involvement in this program is part of its
commitment to protecting our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
NOTE: This equipment has been tested and found to comply with the requirements
for a Class B digital device under Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation. Privacy of communications may not be ensured when using this
telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio
frequency energy that can be safely absorbed by a user or bystander according to the
intended usage of the product. This product has been tested and found to comply
with the FCC criteria. The handset may be safely held against the ear of the user. The
telephone base shall be installed and used such that parts of the user’s body other than
the hands are maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements
adopted by the Administrative Council for Terminal Attachments (ACTA). The label
on the back or bottom of this equipment contains, among other things, a product
identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your
telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the
telephone network must comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible modular
jack that is also compliant. An RJ11 jack should normally be used for connecting to a
single line and an RJ14 jack for two lines. See the installation instructions in the user’s
manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you
may connect to your telephone line and still have them ring when you are called.
The REN for this product is encoded as the 6th and 7th characters following the US:
in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the
sum of all RENs should be five (5.0) or less. For more information, please contact your
telephone service provider.
This equipment must not be used with Party Lines. If you have specially wired alarm
dialing equipment connected to your telephone line, ensure the connection of this
equipment does not disable your alarm equipment. If you have questions about what
will disable alarm equipment, consult your telephone service provider or a qualified
installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until
the problem has been corrected. Replacement to this telephone equipment can only
be made by the manufacturer or its authorized agents. For replacement procedures,
follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service
provider may temporarily discontinue your telephone service. The telephone service
provider is required to notify you before interrupting service. If advance notice is not
practical, you will be notified as soon as possible. You will be given the opportunity to
correct the problem and the telephone service provider is required to inform you of
your right to file a complaint with the FCC. Your telephone service provider may make
changes in its facilities, equipment, operation, or procedures that could affect the
proper functioning of this product. The telephone service provider is required to notify
you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid
compatible.
If this product has memory dialing locations, you may choose to store emergency
telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test
emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the
Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN
indicates the maximum number of devices allowed to be connected to a telephone
interface. The termination of an interface may consist of any combination of devices
subject only to the requirement that the sum of the RENs of all the devices not exceed
five.
This product meets the applicable Innovation, Science and Economic Development
Canada technical specifications.
California Energy Commission battery
charging testing instructions
This telephone is set up to comply with the energy-conserving standards right out of the
box. These instructions are intended for California Energy Commission (CEC) compliance
testing only. When the CEC battery charging testing mode is activated, all telephone
functions, except battery charging, will be disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet. Make sure all
handsets are plugged with charged batteries before proceeding.
2. While you press and hold FIND HS, plug the telephone base power adapter back to
the power outlet.
3. After about 20 seconds, when the IN USE light starts flashing, release FIND HS and
then press it again within two seconds. You hear a confirmation tone. The IN USE
light turns off and all handsets display To register HS... see manual. Allow up to one
minute for the process to complete.
If the phone fails to enter this mode, repeat all the steps mentioned above. The
telephone base will be powered up as normal if you fail to press FIND HS within two
seconds in Step 3.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet, and then plug it
back in. Then the telephone base is powered up as normal.
2. Put the handsets on the telephone base cradle to begin registration.
3. The handset shows Registering... If the registration is successful, the handset screen
displays Registered and beeps. The handset is registered with the telephone base.
Limited Warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase
(“Consumer” or “you”) that the Product and all accessories provided in the sales package
(“Product”) are free from defects in material and workmanship, pursuant to the following
terms and conditions, when installed and used normally and in accordance with the
Product operating instructions. This limited warranty extends only to the Consumer for
Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and
workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will replace at
VTech’s option, without charge, a Materially Defective Product. If we choose to replace the
Product, we may replace it with a new or refurbished Product of the same or similar design.
We will retain defective parts, modules, or equipment. Replacement of the Product, at
VTech’s option, is your exclusive remedy. VTech will return the replacement Products to you
in working condition. You should expect the replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of
purchase. If VTech replaces a Materially Defective Product under the terms of this limited
warranty, this limited warranty also applies to the replacement Product for a period of
either (a) 90 days from the date the replacement Product is shipped to you or (b) the time
remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical
damage, improper installation, abnormal operation or handling, neglect,
inundation, fire, water or other liquid intrusion.
2. Product that has been subjected to contact with liquid, water, rain, extreme
humidity or heavy perspiration, sand, dirt or the like; but then only to the extent
the damage was not caused by incorrectly securing the waterproof handset’s
protective elements, for example, failing to properly close a seal), or such
protective elements are damaged or missing (e.g. a cracked battery door), or
subjecting a Product to conditions beyond its stated specifications or limits (e.g. 30
minutes in 1 meter of fresh water).
3. Product that has been damaged due to repair, alteration or modification by
anyone other than an authorized service representative of VTech;
4. Product to the extent that the problem experienced is caused by signal conditions,
network reliability, or cable or antenna systems;
5. Product to the extent that the problem is caused by use with non-VTech
accessories;
6. Product whose warranty/quality stickers, product serial number plates or electronic
serial numbers have been removed, altered or rendered illegible;
7. Product purchased, used, serviced, or shipped for repair from outside the United
States of America or Canada, or used for commercial or institutional purposes
(including but not limited to Products used for rental purposes);
8. Product returned without a valid proof of purchase (see item 2 below); or
9. Charges for installation or set up, adjustment of customer controls, and installation or
repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the United States of America, please visit our website at
www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or dial 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s
controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during
transit and transportation and are responsible for delivery or handling charges incurred in
the transport of the Product(s) to the service location. VTech will return replaced Product
under this limited warranty. Transportation, delivery or handling charges are prepaid.
VTech assumes no risk for damage or loss of the Product in transit. If the Product failure
is not covered by this limited warranty, or proof of purchase does not meet the terms of
this limited warranty, VTech will notify you and will request that you authorize the cost of
replacement prior to any further activity. You must pay for the cost of replacement and
return shipping costs for the replacement of Products that are not covered by this limited
warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech
service location along with a description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product
purchased (Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone
number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It
supersedes all other written or oral communications related to this Product. VTech
provides no other warranties for this Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There are no other express warranties. No
one is authorized to make modifications to this limited warranty and you should not rely
on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may
also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited
to one year from the date of purchase. Some states/provinces do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to you. In no
event shall VTech be liable for any indirect, special, incidental, consequential, or similar
damages (including, but not limited to lost profits or revenue, inability to use the Product or
other associated equipment, the cost of substitute equipment, and claims by third parties)
resulting from the use of this Product. Some states/provinces do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
Please retain your original sales receipt as proof of purchase
Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any damage
or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its
suppliers assume no responsibility for any loss or claims by third parties that may arise
through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
4Set your headset to
discoverable mode.
Press / to scroll
to Add BT headset,
then press SELECT.
3
5Refer to the user’s manual of
your Bluetooth headset on how
to pair it to your IS8121/
IS8121-2/IS8121-3/IS8121-4/
IS8121-5 telephone.
1Press MENU.2Press / to scroll to
Bluetooth, then press
SELECT.
Cellphone 00:03
ECO 1
10:30PM 11/20
1Press MENU.2Press / to scroll
to Bluetooth, then
press SELECT.
3Press / to scroll to
Download DIR,
then press SELECT.
Bluetooth
ECO 1
Download DIR
ECO 1
Your cell phone
ECO 1
Downloading...
0
ECO 1
Entries added:
XX
ECO 1
ECO
HANDSET
10:15pm 12/25
1
HANDSET
10:15pm 12/25
1 1
Add BT headset
ECO 1
Search headset...
ECO 1
Set number of rings
You can set your answering system to answer calls at least two rings earlier than your voicemail service. For example, if your voicemail service answers after six
rings, set your answering system to answer after four rings. Thus, if you are on a call, or if the answering system is busy recording a message and you receive
another call, the second caller can leave a voicemail message.
HANDSET
ECO
10:30PM 11/20
1Press MENU.
3
ECO
5Press / to scroll to desired
number of rings, then press SELECT.
Answering sys
ECO
2Press / to scroll to
Answering sys, then
press SELECT.
Press / to scroll to
Ans sys setup, then
press SELECT.
Ans sys setup
ECO
3
# of rings
ECO
4Press / to scroll to # of
rings, then press SELECT.
Message playback
Telephone base:
Press
Handset:
ECO
Handset
10:15pm 12/25
Play messages
ECO
Turn the built-in answering system on or off
On the telephone base
Press
Press to turn on;
press again to turn off.
Press MENU.
12Press SELECT
to select Play messages.
Repeat the playing message
Skip a message
Press
- OR -
Play the previous message
Press
1
2
- OR -
Delete all old messages
Press
1
2
- OR -
Press
- OR - 12
Press SELECT to
select your cell
phone.
4
S
m
US CA
-
1
-
2
VTech IS8121-4 Guide de démarrage rapide
- Catégorie
- Téléphones
- Taper
- Guide de démarrage rapide
dans d''autres langues
- English: VTech IS8121-4 Quick start guide
Documents connexes
-
VTech IS8121 Mode d'emploi
-
VTech VG101-31 Mode d'emploi
-
VTech CS5249 Guide de démarrage rapide
-
VTech CS5329-3 Guide de démarrage rapide
-
-
-
VTech IS8102 Manuel utilisateur
-
-
-