Lenco DAR-030 Manuel utilisateur

1

Model: DAR-030

USER MANUAL

Stereo DAB+ and FM radio with

Bluetooth

HANDLEIDING

Stereo DAB+ en FM-radio met Bluetooth

BEDIENUNGSANLEITUNG

Stereo-DAB+/FM-Radio mit Bluetooth

MODE D’EMPLOI

Radio stéréo DAB+ et FM avec Bluetooth

MANUAL DEL USUARIO

Radio estéreo DAB+ y FM con Bluetooth

2

Index:

English ..................................................................................................................................................... 3

Nederlands ............................................................................................................................................ 21

Deutsch ................................................................................................................................................. 40

Français ................................................................................................................................................. 60

Español .................................................................................................................................................. 79

Version: 3.0

3

English

DAR-030

CAUTION:

Usage of controls or adjustments or performance of procedures other than those specified herein

may result in hazardous radiation exposure.

PRECAUTIONS BEFORE USE

KEEP THESE INSTRUCTIONS IN MIND:

1. Do not cover or block any ventilation openings. When placing the device on a shelf, leave

5 cm (2”) free space around the whole device.

2. Install in accordance with the supplied user manual.

3. Keep the device away from heat sources such as radiators, heaters, stoves, candles and other

heat-generating products or naked flame. The device can only be used in moderate climates.

Extremely cold or warm environments should be avoided. Working temperature between 0°

and 35°C.

4. Avoid using the device near strong magnetic fields.

5. Electrostatic discharge can disturb normal usage of this device. If so, simply reset and restart

the device following the instruction manual. During file transmission, please handle with care

and operate in a static-free environment.

6. Warning! Never insert an object into the product through the vents or openings. High voltage

flows through the product and inserting an object can cause electric shock and/or short circuit

internal parts. For the same reason, do not spill water or liquid on the product.

7. Do not use in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.

8. The device shall not be exposed to dripping or splashing and make sure that no objects filled

with liquids, such as vases, are placed on or near the apparatus.

9. Do not use this device when condensation may occur. When the unit is used in a warm wet

room with damp, water droplets or condensation may occur inside the unit and the unit may

not function properly; let the unit stand in power OFF for 1 or 2 hours before turning on the

power: the unit should be dry before getting any power.

10. Although this device is manufactured with the utmost care and checked several times before

leaving the factory, it is still possible that problems may occur, as with all electrical appliances.

If you notice smoke, an excessive build-up of heat or any other unexpected phenomena, you

should disconnect the plug from the main power socket immediately.

11. This device must operate on a power source as specified on the specification label. If you are

not sure of the type of power supply used in your home, consult your dealer or local power

company.

12. Keep away from animals. Some animals enjoy biting on power cords.

13. To clean the device, use a soft dry cloth. Do not use solvents or petrol based fluids.

To remove severe stains, you may use a damp cloth with dilute detergent.

14. The supplier is not responsible for damage or lost data caused by malfunction, misuse,

modification of the device or battery replacement.

15. Do not interrupt the connection when the device is formatting or transferring files. Otherwise,

data may be corrupted or lost.

16. If the unit has USB playback function, the USB memory stick should be plugged into the unit

directly. Don’t use an USB extension cable because it can cause interference resulting in failing

of data.

17. The rating label has been marked on the bottom or back panel of the device.

18. This device is not intended for use by people (including children) with physical, sensory or

mental disabilities, or a lack of experience and knowledge, unless they’re under supervision or

have received instructions about the correct use of the device by the person who is responsible

for their safety.

19. This product is intended for non professional use only and not for commercial or industrial use.

4

20. Make sure the unit is adjusted to a stable position. Damage caused by using this product in an

unstable position vibrations or shocks or by failure to follow any other warning or precaution

contained within this user manual will not be covered by warranty.

21. Never remove the casing of this device.

22. Never place this device on other electrical equipment.

23. Do not allow children access to plastic bags.

24. Only use attachments/accessories specified by the manufacturer.

25. Refer all servicing to qualified service personnel. Servicing is required when the device has

been damaged in any way, such as the power supply cord or the plug, when liquid has been

spilled or objects have fallen into the device, when the device has been exposed to rain or

moisture, does not operate normally, or has been dropped.

26. Long exposure to loud sounds from personal music players may lead to temporary or

permanent hearing loss.

27. If the product is delivered with power cable or AC power adaptor:

⚫ If any trouble occur, disconnect the AC power cord and refer servicing to qualified

personnel.

⚫ Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and

the cable’s exit point. Do not place heavy items on the power adaptor, which may

damage it. Keep the entire device out of children’s reach! When playing with the power

cable, they can seriously injure themselves.

⚫ Unplug this device during lightning storms or when unused for a long period.

⚫ The socket outlet must be installed near the equipment and must be easily accessible.

⚫ Do not overload ac outlets or extension cords. Overloading can cause fire or electric

shock.

⚫ Devices with class 1 construction should be connected to a main socket outlet with a

protective earthed connection.

⚫ Devices with class 2 construction do not require a earthed connection.

⚫ Always hold the plug when pulling it out of the main supply socket. Do not pull the power

cord. This can cause a short circuit.

⚫ Do not use a damaged power cord or plug or a loose outlet. Doing so may result in fire or

electric shock.

28. If the product contains or is delivered with a remote control containing coin/cell batteries:

Warning:

⚫ “Do not ingest battery, Chemical Burn Hazard” or equivalent working.

⚫ [The remote control supplied with] This product contains a coin/button cell battery. If the

battery is swallowed, it can cause severe internal burns in just

2 hours and can lead to death.

⚫ Keep new and used batteries away from children.

⚫ If the battery compartment does not close securely, stop using the product and keep it

away from children.

⚫ If you think batteries might have been swallowed or placed inside any part of the body,

seek immediate medical attention.

29. Caution about the use of Batteries:

⚫ Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type.

⚫ Battery cannot be subjected to high or low extreme temperatures, low air pressure at

high altitude during use, storage or transportation.

⚫ Replacement of a battery with an incorrect type that can result in an explosion or the

leakage of flammable liquid or gas.

⚫ Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a

battery, that can result in an explosion.

⚫ Leaving a battery in an extremely high temperature surrounding environment that can

result in an explosion or that leakage of flammable liquid or gas.

⚫ A battery subjected to extremely low air pressure that may result in an explosion or the

leakage of flammable liquid or gas.

⚫ Attention should be drawn to the environmental aspects of battery disposal.

INSTALLATION

5

• Unpack all parts and remove protective material.

• Do not connect the unit to the mains before checking the mains voltage and before all other

connections have been made.

6

Accessories:

1. User manual

2. Power adaptor

3. Remote control

7

Product Front Overview

1. Left/Stations button

2. Menu button

3. Standby button

4. Mode button

5. Preset button

6. Sleep button

7. Back/Right button

8. Alarm button

9. OK/Vol+/Vol-/Nagivate/play/pause/Snooze/Info knob

10. Color display

8

Product Top Overview

11. 5 preset buttons

Product Rear Overview

12. On/off switch button

13. DC IN socket

14. Headphone out socket

15. Telescopic antenna

9

Remote control Overview

1. Standby button

2. Mute button

3. Up button

4. Left button

5. Right button

6. Down button

7. OK/play/pause button

8. Vol+ button

9. Vol- button

10. Mode button

11. Snooze button

12. Preset button

10

13. Scan button

14. Alarm button

15. Back button

16. Sleep button

17. Stereo/Mono button

18. Dimmer button

19. Preset number buttons

20. Info button

21. Menu button

Initial use

Before operation, please make sure that the VOLTAGE mentioned on the power supply is same as

the voltage of your local area.

Use the supplied mains adaptor to connect the device to a household mains socket.

Switch the device on with the power switch on the rear.

Basic operation-getting started

1. Connect the mains adaptor to the micro USBjack, fully extend the telescopic antenna, plug in

and switch on at the mains.

2. The display backlight will illuminateand the clock(00:00:00)(Time is not set) will flash

3. On the very first use The DAB mode will automatically be selected and the radio will perform a

fullscan. The display will show ‘Scanning’with a bar indicator showingthe scan progress and the

total number of stations found.

4. When the scan is finished the radio will play the first alphanumerically found station. If the

radio does not find any stations, ‘No DAB Station’ will be displayed.

5. Adjust the volume to the desired level using the VOL(+/-) knob.

6. Press the stations button and use knob to scroll through the stations list. Press the OK knob on

your favorite station.

7. Pressthe Mode button to switch between DAB, FM, Bluetooth and Aux input mode,

8. Press and hold the Standby button to go into ‘Standby’ mode.

11

9. Press Sleep to set the Set Sleep Timer:Use Volume knob and rotateto choose betweenSleep off-

15 minutes-30 minutes-45 mintues-60 minutes-90 minutes. The radio will go into standby when

the selected minutes have been counted down.

Using the radio- DAB mode

DAB Mode- Full scan

This function will scan for all available DAB stations, Band III channels.

In DAB mode, press Menu button and rotate the ok knob to select ‘Full Scan’then short press the ok

knob to start the DAB full scan. When the scan is finished, the radio will return to the last played

DAB radio station. All stations found will be listed in the station list, which is show when pressing the

‘stations’ button.

Please note that the available DAB+ radio stations differ per region/city

DAB Mode- Manual tune

This function allows a specific or new ensemble to be manually added to the stations already

available on the radio.

In DAB mode, press the Menu button and use the ok knob to navigateuntil “Manual tune” is

highlighted, press the ok knob to confirm.

Use the okknob to navigate until the desired frequency is selected and then press the okknob, the

frequency and name of the ensemble and the signal strength will be displayed.

Press the okknob again to add the ensemble and automatically tune to that station.

DAB Mode- Prune Invalid

This function will remove unavailable stations from the station list. Press the Menu button. Use the

ok knob to navigate to the “Prune Invalid” option and press the ok knob to confirm.

Rotate the ok knob to select (yes) to proceed to prune the invalid/unavailable stations.If (No) is

selected the operation will be cancelled.

12

DAB Mode- DRC

DRC is dynamic range compression, and it is about increasing the loudness of the quieter parts of

the audio signal, and decreasing the loudness of the louder parts.

In DAB mode, press the Menu button, then use the ok knob to navigate until “DRC” is highlighted.

Press the ok knob to confirm.

Now use the ok knob to cycle through off, high, low level. Press the ok knobto confirm your choice

DAB Mode- display mode

This function will display various information about the current station.

Press the ok knob repeatedly to scroll through the following information:

DLS(dynamic label segment)/ Radio text- The radio station may include a scrolling message about

the current program.

Ensemble/Multiplex(Group name): The ensemble/multiplex is a group of stations that are bundled

and transmitted together in one single frequency. There are national and local multiplexes, local

ones contain stations that are specific to the local area.

Frequency: The display will show the frequency of the station being broadcast.

Signal strength: The display will show a slide bar to indicate the strength of the signal. The stronger

the signal, the longer the bar.

Signal error: This is displayed as number between 0-99. It would not be possible to satisfactorily

listen to a radio station with a signal error rate of 30 or above.

Audio bit rate: The display will show the digital audio bit rate being received.

Time and date: the time and date will be automatically updated by the radio.

DAB mode- System settings

Equalizer: Rotatethe ok knob to choose between -Normal-Classic-Jazz-Pop-Rock-Speech, My EQ, My

EQ set up(Treble, Bass)

13

Time/Date: Set Time/Date

Press the ok knob, the Date digit will flash, rotate the ok knob to choose correct date and press the

ok knob to confirm.

The Month digit will start to flash. Rotate the ok knob to choose correct month and press the ok

knob to confirm.

The Year digit will start to flash. Rotate the ok knob to choose correct year and press the okknob to

confirm.

The Hour digit will start to flash. Rotate the ok knob to choose correct hour and press the okknob to

confirm.

The Minute digit will start to flash. Rotate the ok knob to choosethe correct minute and press the ok

knob to confirm.

Now you have finished the time/date configuration.

Auto update: Choose from what source the radio will update the time automatically.

You can choose the following options:

- Any:updates the time from DAB or FM signal

- From Digital Radio-update:updates the time from the DAB signal

- From FM: updates the time from an RDS channel

- No update: If you want to set the time manually

Set 12/24 hour:Rotate the ok knob to choose to set 24 hour- or 12 hour time display

Set date format: Rotate the ok knob to choose DD-MM-YYYY or MM-DD-YYYY.

Backlight: Timeout: on-10 sec-20 sec-30 sec-45 sec-60 sec-90 sec-120 sec-180 sec

On level: High-Medium-Low

Dim level: High-Medium-Low

Language: English, Nederlands, Deutsch, Italiano, Francais, Dansk

14

Factory reset: Press the Ok knob and choose ‘Yes’ to start factory reset.

Software update: Press the ok knob and choose “yes”to update the software if needed. Updating

can only be done with a micro usb cable.

Remark: only select the software update option if you have an update for this unit. (if you accidently

selected this option, use the power off/on the restart the radio)

SW version: Press OKto view system version.

Using the radio- FM MODE

Turn the radio on, press the Mode button repeatedly and select the FM mode. The display will show

‘FM’ and the current station name or frequency if RDS is not available.

Manual search

To search manually, first short press the stations button and then turn the ok knob right to scan

upwards or turn the ok knob left to scan downwards.

Auto search

To initiate auto search, press and hold the ok knob.The radio starts to scan the frequency band. It

will stop automatically when a station has been found.

If you want the radio to auto search downwards or upwardsthen you have to do a manual search

downwards or upwards prior to long pressing the ok button.

FM mode- Scan settings

Press the menu button and rotate the ok knob to select ‘Scan setting’. Short press the ok knoband

choose between ‘Strong stations only’ or ‘All stations’ by turning the ok knob. Press the ok knob to

confirm your choice. If choose ‘Strong station only’, the radio will only scan and play stations with a

strong signal. If selecting ‘All stations’, the radio will also scan and play stations with a weak signal.

15

FM mode- Audio setting

Press the menu button and rotate the ok knob. Choose ‘Forced mono’ ‘Yes’ or ‘No’ and short press

the ok knob to confirm. If your favorite radio stations signal is weak, then choose ‘Forced mono

‘Yes’’to get better sound quality.

FM mode-System settings (see DAB mode ‘system settings)

FM Display Modes

This function allows information relating to the current station to be shown in the display, short

press the okknob repeatedly to scroll through the following information screens

RDS (scrolling text): The current selected Radio station may include a scrolling message about the

current program.

Program type: This describes the style of the program being broadcast.

Station name: such as BBC RD of the Frequency in Mhz

Audio Mode: The display will show if the station being received is stereo or mono

Time/date: the time and date will be automatically updated by the radio time signal (if RDS is

available).

Using the radio- preset station function

This radio allows you to store up to 10 DAB and 10 FM radio stations as preset. Presets are quickly

selectable radio stations by using the ‘preset’ button on the Radio.

Storing DAB station as preset

Follow the instructions above to select a DAB radio station.

Press and hold the ‘Preset’ button. ‘1:(Empty)’ is displayed. If no previous station has been stored.

Rotate the ok knob to scroll through the preset location that you would like to store the radio

stations to (1-10).

16

Short press the Select knob to store the station. The message “Preset XX saved” will appear on the

display.

Note: There are 5 separate preset buttons on top of the Radio. You can press and hold each button

to store a station. You can also press and hold the number buttons on the remote control to store a

station. (button 0 = preset 10)

Recalling DAB Preset stations

You can quickly select your presets by pressing the Preset button, then rotatethe ok knob to

scrollthrough the stored presets. Short press the ok knob to choose to the selected station.

If you choose an empty preset, then “Preset empty” will be displayed.

To quickly select preset 1 till 5, you can short press the buttons 1 – 5 on top of the radio butit’s also

possible to press the numbers 0-9 on the remote control to select a preset (where 0 = preset 10)

Alarm Setting

Note: Check that the radio has the correct time and date before you set an alarm.

In DAB or FM mode:

Press the ‘Alarm’ button on the front of the radio, ‘Alarm 1off 6:00’ is displayed. Short press theok

knob.

‘Alarm 1 info’ is displayed. Rotate the ok knobto“Alarm” and short press the ok knob to switch the

alarm on- or off.

Rotate the ok knob to scroll to ‘frequency’. You can chooseDaily, Once, Weekends or Weekdays.

Short press the ok knob to confirm you selection

Rotate the ok knob to scroll to ‘Wake Up Time’and short press the ok knob. The Hour digits will start

to flash.

Rotate the ok knob to set the desired hour and then short press the ok knob to confirm.

The minute digits will start to flash.

Rotate the ok knob to set the minutes and short press the ok knob to confirm.

17

Rotate the ok knob to scroll to the Alarm sound ‘source’. You can choose between Buzzer, DAB+

Radio or FM.Short press the ok button to confirm.

Rotate the ok knob to scroll to ‘duration’.You can choose15, 30, 45, 60, 90 or 120 minutes. Short

press the ok knob to confirm.

Rotate the ok knob and select ‘Volume’ to set the volume for your alarm. Rotate the ok knob to set

the volume. (The minimum volume you can select is 4). Short press the ok knobto confirm.Your

Alarm is now ready for use.

Note: The alarm volume will increase progressively until it reaches the alarm volume you have set.

Repeat the above steps to set Alarm 2.

Snooze Function

When the alarm sounds, you can press the ok knobto snooze. The default snooze timeis 9 minutes.

To stop the alarm, press the ‘on/off-Mode’ button.

Bluetooth function

Turn on the radio and short press the Mode button until Bluetooth mode is selected. Turn on the

Bluetooth on your Bluetooth device, search for devices and then select “Lenco DAR-030”. Click it to

pair. When connected successfully you will hear a voice“connected”.

You can press the Stations button to select previous track or the back button to go to the next track.

You can press the ok knob to play or pause the music playback.

The volume can be adjusted by turning the ok knob up- or downwards (note that the volume level is

not synced with the Bluetooth device, meaning you have to turn up the volume of your Bluetooth

device manually first)

To disconnect the existing pairing and pair with new device just press and hold the ok knob.

“This product has a bluetoothreception function, you can’ttransmit any bluetooth sound with it:

this means that you can receive wirelessly a bluetooth sound signal from an external source like a

smartphone.”

18

Technical Specifications

Connections

Micro usb for power adapter,3.5mm headphone out

Power adaptor Input

100-240V~50/60 Hz, 0.2A max

Pwer adaptor Output

5.0V/1.5A

Power consumption

10W (max)

Power consumption (standby)

<1W

Operating Temperature

0°C-35°C

Operating position

Horizontal

Power supply adaptor: (For EU only)

Manufacturer: Shenzhen Adition Audio Science and Technology Co., Ltd

Model Number: AD080A0501500EU-MICROUSB

Use only original AC adaptor

Use only the power supply listed in the user instructions.

Dim. unit

280 x 110 x 110 mm (WxDxH)

Weight

890g

NOTE: Only use the power supply listed in this manual.

Information

Value and and precision

Manufacturers name or trade mark, commercial

registration and address

Adition

Model Identifier

AD080A0501500EU-

MicroUSB

Input voltage

100-240V

Input AC frequency

50/60Hz

Output voltage

5.0V

Output current

1.5A

Output Power

7.5W

Average active efficiency

77.33%

Efficiency at low load (10%)

71.82%

No load Power consumption

0.04W

19

Guarantee

Lenco offers service and warranty in accordance to European law, which means that in case of

repairs (both during and after the warranty period) you should contact your local dealer.

Important note: It is not possible to send products that need repairs to Lenco directly.

Important note: If this unit is opened or accessed by a non-official service center in any way, the

warranty expires.

This device is not suitable for professional use. In case of professional use, all warranty obligations of

the manufacturer will be voided.

20

Disclaimer

Updates to Firmware and/or hardware components are made regularly. Therefore some of the

instruction, specifications and pictures in this documentation may differ slightly from your particular

situation. All items described in this guide for illustration purposes only and may not apply to

particular situation. No legal right or entitlements may be obtained from the description made in

this manual.

Disposal of the Old Device

This symbol indicates that the relevant electrical product or battery should not be

disposed of as general household waste in Europe. To ensure the correct waste

treatment of the product and battery, please dispose them in accordance to any

applicable local laws of requirement for disposal of electrical equipment or

batteries. In so doing, you will help to conserve natural resources and improve

standards of environmental protection in treatment and disposal of electrical

waste (Waste Electrical and Electronic Equipment Directive).

CE Marking

Hereby, Commaxx B.V. Wiebachstraat 37, 6466 NG Kerkrade, The Netherlands, declares that this

product is in compliance with the essential EU directive requirements.

The declaration of conformity may be consulted via techdoc@commaxxgroup.com

Service

For more information and helpdesk support, please visit www.lenco.com

Commaxx B.V. Wiebachstraat 37, 6466 NG Kerkrade, The Netherlands.

La page charge ...

Lenco DAR-030 Manuel utilisateur

Lenco DAR-030 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents