Lenco DAR-030BK Le manuel du propriétaire

Taper
Le manuel du propriétaire
1
Model: DAR-030
USER MANUAL
Stereo DAB+ and FM radio with
Bluetooth
HANDLEIDING
Stereo DAB+ en FM-radio met Bluetooth
BEDIENUNGSANLEITUNG
Stereo-DAB+/FM-Radio mit Bluetooth
MODE D’EMPLOI
Radio stéréo DAB+ et FM avec Bluetooth
MANUAL DEL USUARIO
Radio estéreo DAB+ y FM con Bluetooth
2
Index:
English.....................................................................................................................................................3
Nederlands............................................................................................................................................21
Deutsch .................................................................................................................................................40
Français .................................................................................................................................................60
Español..................................................................................................................................................79
Version: 2.0
3
English
DAR-030
CAUTION:
Usage of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
PRECAUTIONS BEFORE USE
KEEP THESE INSTRUCTIONS IN MIND:
1. Do not cover or block any ventilation openings. When placing the device on a shelf, leave
5 cm (2”) free space around the whole device.
2. Install in accordance with the supplied user manual.
3. Keep the device away from heat sources such as radiators, heaters, stoves, candles and other
heat-generating products or naked flame. The device can only be used in moderate climates.
Extremely cold or warm environments should be avoided. Working temperature between 0°
and 35°C.
4. Avoid using the device near strong magnetic fields.
5. Electrostatic discharge can disturb normal usage of this device. If so, simply reset and restart
the device following the instruction manual. During file transmission, please handle with care
and operate in a static-free environment.
6. Warning! Never insert an object into the product through the vents or openings. High voltage
flows through the product and inserting an object can cause electric shock and/or short circuit
internal parts. For the same reason, do not spill water or liquid on the product.
7. Do not use in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.
8. The device shall not be exposed to dripping or splashing and make sure that no objects filled
with liquids, such as vases, are placed on or near the apparatus.
9. Do not use this device when condensation may occur. When the unit is used in a warm wet
room with damp, water droplets or condensation may occur inside the unit and the unit may
not function properly; let the unit stand in power OFF for 1 or 2 hours before turning on the
power: the unit should be dry before getting any power.
10. Although this device is manufactured with the utmost care and checked several times before
leaving the factory, it is still possible that problems may occur, as with all electrical appliances.
If you notice smoke, an excessive build-up of heat or any other unexpected phenomena, you
should disconnect the plug from the main power socket immediately.
11. This device must operate on a power source as specified on the specification label. If you are
not sure of the type of power supply used in your home, consult your dealer or local power
company.
12. Keep away from animals. Some animals enjoy biting on power cords.
13. To clean the device, use a soft dry cloth. Do not use solvents or petrol based fluids.
To remove severe stains, you may use a damp cloth with dilute detergent.
14. The supplier is not responsible for damage or lost data caused by malfunction, misuse,
modification of the device or battery replacement.
15. Do not interrupt the connection when the device is formatting or transferring files. Otherwise,
data may be corrupted or lost.
16. If the unit has USB playback function, the USB memory stick should be plugged into the unit
directly. Don’t use an USB extension cable because it can cause interference resulting in failing
of data.
17. The rating label has been marked on the bottom or back panel of the device.
18. This device is not intended for use by people (including children) with physical, sensory or
mental disabilities, or a lack of experience and knowledge, unless they’re under supervision or
have received instructions about the correct use of the device by the person who is responsible
for their safety.
19. This product is intended for non professional use only and not for commercial or industrial use.
4
20. Make sure the unit is adjusted to a stable position. Damage caused by using this product in an
unstable position vibrations or shocks or by failure to follow any other warning or precaution
contained within this user manual will not be covered by warranty.
21. Never remove the casing of this device.
22. Never place this device on other electrical equipment.
23. Do not allow children access to plastic bags.
24. Only use attachments/accessories specified by the manufacturer.
25. Refer all servicing to qualified service personnel. Servicing is required when the device has
been damaged in any way, such as the power supply cord or the plug, when liquid has been
spilled or objects have fallen into the device, when the device has been exposed to rain or
moisture, does not operate normally, or has been dropped.
26. Long exposure to loud sounds from personal music players may lead to temporary or
permanent hearing loss.
27. If the product is delivered with power cable or AC power adaptor:
If any trouble occur, disconnect the AC power cord and refer servicing to qualified
personnel.
Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and
the cable’s exit point. Do not place heavy items on the power adaptor, which may
damage it. Keep the entire device out of children’s reach! When playing with the power
cable, they can seriously injure themselves.
Unplug this device during lightning storms or when unused for a long period.
The socket outlet must be installed near the equipment and must be easily accessible.
Do not overload ac outlets or extension cords. Overloading can cause fire or electric shock.
Devices with class 1 construction should be connected to a main socket outlet with a
protective earthed connection.
Devices with class 2 construction do not require a earthed connection.
Always hold the plug when pulling it out of the main supply socket. Do not pull the power
cord. This can cause a short circuit.
Do not use a damaged power cord or plug or a loose outlet. Doing so may result in fire or
electric shock.
28. If the product contains or is delivered with a remote control containing coin/cell batteries:
Warning:
“Do not ingest battery, Chemical Burn Hazard” or equivalent working.
[The remote control supplied with] This product contains a coin/button cell battery. If the
battery is swallowed, it can cause severe internal burns in just
2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it
away from children.
If you think batteries might have been swallowed or placed inside any part of the body,
seek immediate medical attention.
29. Caution about the use of Batteries:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type.
Battery cannot be subjected to high or low extreme temperatures, low air pressure at
high altitude during use, storage or transportation.
Replacement of a battery with an incorrect type that can result in an explosion or the
leakage of flammable liquid or gas.
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a
battery, that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that can
result in an explosion or that leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an explosion or the
leakage of flammable liquid or gas.
Attention should be drawn to the environmental aspects of battery disposal.
INSTALLATION
5
Unpack all parts and remove protective material.
Do not connect the unit to the mains before checking the mains voltage and before all other
connections have been made.
6
Accessories:
1. User manual
2. Power adaptor
3. Remote control
7
Product Front Overview
1. Left/Stations button
2. Menu button
3. Standby button
4. Mode button
5. Preset button
6. Sleep button
7. Back/Right button
8. Alarm button
9. OK/Vol+/Vol-/Nagivate/play/pause/Snooze/Info knob
10. Color display
8
Product Top Overview
11. 5 preset buttons
Product Rear Overview
12. On/off switch button
13. DC IN socket
14. Headphone out socket
15. Telescopic antenna
9
Remote control Overview
1. Standby button
2. Mute button
3. Up button
4. Left button
5. Right button
6. Down button
7. OK/play/pause button
8. Vol+ button
9. Vol- button
10. Mode button
11. Snooze button
12. Preset button
10
13. Scan button
14. Alarm button
15. Back button
16. Sleep button
17. Stereo/Mono button
18. Dimmer button
19. Preset number buttons
20. Info button
21. Menu button
Initial use
Before operation, please make sure that the VOLTAGE mentioned on the power supply is same as
the voltage of your local area.
Use the supplied mains adaptor to connect the device to a household mains socket.
Switch the device on with the power switch on the rear.
Basic operation-getting started
Basic operation-getting started
1. Connect the mains adaptor to the micro USBjack, fully extend the telescopic antenna, plug in
and switch on at the mains.
2. The display backlight will illuminateand the clock(00:00:00)(Time is not set) will flash
3. On the very first use The DAB mode will automatically be selected and the radio will perform a
fullscan. The display will show ‘Scanning’with a bar indicator showingthe scan progress and the
total number of stations found.
4. When the scan is finished the radio will play the first alphanumerically found station. If the
radio does not find any stations, ‘No DAB Station’ will be displayed.
5. Adjust the volume to the desired level using the VOL(+/-) knob.
6. Press the stations button and use knob to scroll through the stations list. Press the OK knob on
your favorite station.
7. Pressthe Mode button to switch between DAB, FM, Bluetooth and Aux input mode,
8. Press and hold the Standby button to go into ‘Standby’ mode.
11
9. Press Sleep to set the Set Sleep Timer:Use Volume knob and rotateto choose betweenSleep off-
15 minutes-30 minutes-45 mintues-60 minutes-90 minutes. The radio will go into standby when
the selected minutes have been counted down.
Using the radio- DAB mode
DAB Mode- Full scan
This function will scan for all available DAB stations, Band III channels.
In DAB mode, press Menu button and rotate the ok knob to select ‘Full Scan’then short press the ok
knob to start the DAB full scan. When the scan is finished, the radio will return to the last played
DAB radio station. All stations found will be listed in the station list, which is show when pressing the
‘stations’ button.
Please note that the available DAB+ radio stations differ per region/city
DAB Mode- Manual tune
This function allows a specific or new ensemble to be manually added to the stations already
available on the radio.
In DAB mode, press the Menu button and use the ok knob to navigateuntil “Manual tune” is
highlighted, press the ok knob to confirm.
Use the okknob to navigate until the desired frequency is selected and then press the okknob, the
frequency and name of the ensemble and the signal strength will be displayed.
Press the okknob again to add the ensemble and automatically tune to that station.
DAB Mode- Prune Invalid
This function will remove unavailable stations from the station list. Press the Menu button. Use the
ok knob to navigate to the “Prune Invalid” option and press the ok knob to confirm.
Rotate the ok knob to select (yes) to proceed to prune the invalid/unavailable stations.If (No) is
selected the operation will be cancelled.
12
DAB Mode- DRC
DRC is dynamic range compression, and it is about increasing the loudness of the quieter parts of
the audio signal, and decreasing the loudness of the louder parts.
In DAB mode, press the Menu button, then use the ok knob to navigate until “DRC” is highlighted.
Press the ok knob to confirm.
Now use the ok knob to cycle through off, high, low level. Press the ok knobto confirm your choice
DAB Mode- display mode
This function will display various information about the current station.
Press the ok knob repeatedly to scroll through the following information:
DLS(dynamic label segment)/ Radio text- The radio station may include a scrolling message about
the current program.
Ensemble/Multiplex(Group name): The ensemble/multiplex is a group of stations that are bundled
and transmitted together in one single frequency. There are national and local multiplexes, local
ones contain stations that are specific to the local area.
Frequency: The display will show the frequency of the station being broadcast.
Signal strength: The display will show a slide bar to indicate the strength of the signal. The stronger
the signal, the longer the bar.
Signal error: This is displayed as number between 0-99. It would not be possible to satisfactorily
listen to a radio station with a signal error rate of 30 or above.
Audio bit rate: The display will show the digital audio bit rate being received.
Time and date: the time and date will be automatically updated by the radio.
DAB mode- System settings
Equalizer: Rotatethe ok knob to choose between -Normal-Classic-Jazz-Pop-Rock-Speech, My EQ, My
EQ set up(Treble, Bass)
13
Time/Date: Set Time/Date
Press the ok knob, the Date digit will flash, rotate the ok knob to choose correct date and press the
ok knob to confirm.
The Month digit will start to flash. Rotate the ok knob to choose correct month and press the ok
knob to confirm.
The Year digit will start to flash. Rotate the ok knob to choose correct year and press the okknob to
confirm.
The Hour digit will start to flash. Rotate the ok knob to choose correct hour and press the okknob to
confirm.
The Minute digit will start to flash. Rotate the ok knob to choosethe correct minute and press the ok
knob to confirm.
Now you have finished the time/date configuration.
Auto update: Choose from what source the radio will update the time automatically.
You can choose the following options:
- Any:updates the time from DAB or FM signal
- From Digital Radio-update:updates the time from the DAB signal
- From FM: updates the time from an RDS channel
- No update: If you want to set the time manually
Set 12/24 hour:Rotate the ok knob to choose to set 24 hour- or 12 hour time display
Set date format: Rotate the ok knob to choose DD-MM-YYYY or MM-DD-YYYY.
Backlight: Timeout: on-10 sec-20 sec-30 sec-45 sec-60 sec-90 sec-120 sec-180 sec
On level: High-Medium-Low
Dim level: High-Medium-Low
Language: English, Nederlands, Deutsch, Italiano, Francais, Dansk
14
Factory reset: Press the Ok knob and choose ‘Yes’ to start factory reset.
Software update: Press the ok knob and choose “yes”to update the software if needed. Updating
can only be done with a micro usb cable.
Remark: only select the software update option if you have an update for this unit. (if you accidently
selected this option, use the power off/on the restart the radio)
SW version: Press OKto view system version.
Using the radio- FM MODE
Turn the radio on, press the Mode button repeatedly and select the FM mode. The display will show
‘FM’ and the current station name or frequency if RDS is not available.
Manual search
To search manually, first short press the stations button and then turn the ok knob right to scan
upwards or turn the ok knob left to scan downwards.
Auto search
To initiate auto search, press and hold the ok knob.The radio starts to scan the frequency band. It
will stop automatically when a station has been found.
If you want the radio to auto search downwards or upwardsthen you have to do a manual search
downwards or upwards prior to long pressing the ok button.
FM mode- Scan settings
Press the menu button and rotate the ok knob to select ‘Scan setting’. Short press the ok knoband
choose between ‘Strong stations only’ or ‘All stations’ by turning the ok knob. Press the ok knob to
confirm your choice. If choose ‘Strong station only’, the radio will only scan and play stations with a
strong signal. If selecting ‘All stations’, the radio will also scan and play stations with a weak signal.
15
FM mode- Audio setting
Press the menu button and rotate the ok knob. Choose ‘Forced mono’ ‘Yes’ or ‘No’ and short press
the ok knob to confirm. If your favorite radio stations signal is weak, then choose ‘Forced mono
‘Yes’’to get better sound quality.
FM mode-System settings (see DAB mode ‘system settings)
FM Display Modes
This function allows information relating to the current station to be shown in the display, short
press the okknob repeatedly to scroll through the following information screens
RDS (scrolling text): The current selected Radio station may include a scrolling message about the
current program.
Program type: This describes the style of the program being broadcast.
Station name: such as BBC RD of the Frequency in Mhz
Audio Mode: The display will show if the station being received is stereo or mono
Time/date: the time and date will be automatically updated by the radio time signal (if RDS is
available).
Using the radio- preset station function
This radio allows you to store up to 10 DAB and 10 FM radio stations as preset. Presets are quickly
selectable radio stations by using the ‘preset’ button on the Radio.
Storing DAB station as preset
Follow the instructions above to select a DAB radio station.
Press and hold the ‘Preset’ button. ‘1:(Empty)’ is displayed. If no previous station has been stored.
Rotate the ok knob to scroll through the preset location that you would like to store the radio
stations to (1-10).
16
Short press the Select knob to store the station. The message “Preset XX saved” will appear on the
display.
Note: There are 5 separate preset buttons on top of the Radio. You can press and hold each button
to store a station. You can also press and hold the number buttons on the remote control to store a
station. (button 0 = preset 10)
Recalling DAB Preset stations
You can quickly select your presets by pressing the Preset button, then rotatethe ok knob to
scrollthrough the stored presets. Short press the ok knob to choose to the selected station.
If you choose an empty preset, then “Preset empty” will be displayed.
To quickly select preset 1 till 5, you can short press the buttons 1 – 5 on top of the radio butit’s also
possible to press the numbers 0-9 on the remote control to select a preset (where 0 = preset 10)
Alarm Setting
Note: Check that the radio has the correct time and date before you set an alarm.
In DAB or FM mode:
Press the ‘Alarm’ button on the front of the radio, ‘Alarm 1off 6:00’ is displayed. Short press theok
knob.
‘Alarm 1 info’ is displayed. Rotate the ok knobto“Alarm” and short press the ok knob to switch the
alarm on- or off.
Rotate the ok knob to scroll to ‘frequency’. You can chooseDaily, Once, Weekends or Weekdays.
Short press the ok knob to confirm you selection
Rotate the ok knob to scroll to ‘Wake Up Time’and short press the ok knob. The Hour digits will start
to flash.
Rotate the ok knob to set the desired hour and then short press the ok knob to confirm.
The minute digits will start to flash.
Rotate the ok knob to set the minutes and short press the ok knob to confirm.
17
Rotate the ok knob to scroll to the Alarm sound ‘source’. You can choose between Buzzer, DAB+
Radio or FM.Short press the ok button to confirm.
Rotate the ok knob to scroll to ‘duration’.You can choose15, 30, 45, 60, 90 or 120 minutes. Short
press the ok knob to confirm.
Rotate the ok knob and select ‘Volume’ to set the volume for your alarm. Rotate the ok knob to set
the volume. (The minimum volume you can select is 4). Short press the ok knobto confirm.Your
Alarm is now ready for use.
Note: The alarm volume will increase progressively until it reaches the alarm volume you have set.
Repeat the above steps to set Alarm 2.
Snooze Function
When the alarm sounds, you can press the ok knobto snooze. The default snooze timeis 9 minutes.
To stop the alarm, press the ‘on/off-Mode’ button.
Bluetooth function
Turn on the radio and short press the Mode button until Bluetooth mode is selected. Turn on the
Bluetooth on your Bluetooth device, search for devices and then select “Lenco DAR-030”. Click it to
pair. When connected successfully you will hear a voice“connected”.
You can press the Stations button to select previous track or the back button to go to the next track.
You can press the ok knob to play or pause the music playback.
The volume can be adjusted by turning the ok knob up- or downwards (note that the volume level is
not synced with the Bluetooth device, meaning you have to turn up the volume of your Bluetooth
device manually first)
To disconnect the existing pairing and pair with new device just press and hold the ok knob.
“This product has a bluetoothreception function, you can’ttransmit any bluetooth sound with it:
this means that you can receive wirelessly a bluetooth sound signal from an external source like a
smartphone.”
18
Technical Specifications
Connections
Micro usb for power adapter,3.5mm headphone out
Power adaptor Input
100-240V~50/60 Hz, 0.2A max
Pwer adaptor Output
5.0V/1.5A
Power consumption
10W (max)
Power consumption (standby)
<1W
Operating Temperature
0°C-35°C
Operating position
Horizontal
Power supply adaptor: (For EU only)
Manufacturer: Shenzhen Adition Audio Science and Technology Co., Ltd
Model Number: AD080A0501500EU-MICROUSB
Use only original AC adaptor
Use only the power supply listed in the user instructions.
280 x 110 x 110 mm (WxDxH)
890g
NOTE: Only use the power supply listed in this manual.
Information
Value and and precision
Manufacturers name or trade mark, commercial
registration and address
Adition
Model Identifier
AD080A0501500EU-
MicroUSB
Input voltage
100-240V
Input AC frequency
50/60Hz
Output voltage
5.0V
Output current
1.5A
Output Power
7.5W
Average active efficiency
77.33%
Efficiency at low load (10%)
71.82%
No load Power consumption
0.04W
19
Guarantee
Lenco offers service and warranty in accordance to European law, which means that in case of
repairs (both during and after the warranty period) you should contact your local dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note: If this unit is opened or accessed by a non-official service center in any way, the
warranty expires.
This device is not suitable for professional use. In case of professional use, all warranty obligations of
the manufacturer will be voided.
20
Disclaimer
Updates to Firmware and/or hardware components are made regularly. Therefore some of the
instruction, specifications and pictures in this documentation may differ slightly from your particular
situation. All items described in this guide for illustration purposes only and may not apply to
particular situation. No legal right or entitlements may be obtained from the description made in
this manual.
Disposal of the Old Device
This symbol indicates that the relevant electrical product or battery should not be
disposed of as general household waste in Europe. To ensure the correct waste
treatment of the product and battery, please dispose them in accordance to any
applicable local laws of requirement for disposal of electrical equipment or
batteries. In so doing, you will help to conserve natural resources and improve
standards of environmental protection in treatment and disposal of electrical
waste (Waste Electrical and Electronic Equipment Directive).
CE Marking
Hereby, Lenco Benelux B.V., Thermiekstraat 1a, 6361 HB Nuth, The Netherlands, declares that this
product is in compliance with the essential EU directive requirements.
The declaration of conformity may be consulted via techdoc@commaxxgroup.com
Service
For more information and helpdesk support, please visit www.lenco.com
Lenco Benelux BV, Thermiekstraat 1a, 6361 HBNuth, The Netherlands.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97

Lenco DAR-030BK Le manuel du propriétaire

Taper
Le manuel du propriétaire