Sauder 419517 Mode d'emploi

sauder.com

Dresser

Model 419517

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

English pg 1-22

Français pg 23-25

Español pg 26-28

Lot # 531876 07/23/19

Purchased: __________________

sauder.com

CONTACT US FIRST

BEFORE MAKING ANY RETURNS TO THE STORE.

Share your journey!

sauder.com

CONTACT US FIRST

BEFORE MAKING ANY RETURNS TO THE STORE.

Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.

Prefer the phone? Give us a ring at

1-800-523-3987.

Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)

WARNING

CHOKING HAZARD - Small Parts

Not for children under 3 years.

Adult assembly required.

Table of Contents Assembly Tools Required

2-3

4

5-22

23-25

26-28

29-30

31

Part Identiﬁ cation

Hardware Identiﬁ cation

Assembly Steps

Français

Español

Safety

Warranty

Hammer

Not actual size

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Skip the power trip.

This time.

419517 www.sauder.com/servicePage 2

Part Identiﬁ cation

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge

to help distinguish similar parts from each other. Use this part identiﬁ cation to help identify similar parts.

A RIGHT END (1)

B LEFT END (1)

C UPRIGHT (1)

D TOP (1)

D50 LOWER RIGHT DRAWER SIDE (4)

D51 LOWER LEFT DRAWER SIDE (4)

D166 UPPER DRAWER BACK (2)

D167 LOWER DRAWER BACK (4)

D212 UPPER RIGHT DRAWER SIDE (2)

D213

UPPER LEFT DRAWER SIDE (2)

- 1 with label

D975 DRAWER BOTTOM (6)

E BOTTOM (1)

F BACK (1)

H FRONT LEG (2)

I BACK LEG (2)

J UPPER RIGHT DRAWER FRONT (1)

K UPPER LEFT DRAWER FRONT (1)

L

LOWER RIGHT DRAWER FRONT (2)

M LOWER LEFT DRAWER FRONT (2)

M65

DRAWER BRACE (6)

(Hidden part using recycled

material. Color may vary.)

N FRONT MOLDING (1)

O BOTTOM MOLDING (1)

P FOOT (2)

Part Identiﬁ cation

Now you know

our ABCs.

419517www.sauder.com/service

Page 3

D975

D212

D50

D51

D166

D213

D167

D975

J

L

D212

D166

D213

D975

K

D975

D50

D51

D167

M

M65

A

B

C

D

E

F

H

I

N

O

P

H

I

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

419517 www.sauder.com/servicePage 4

5E

CORNER CAP - 1

6E

FOOT BRACKET - 1

SAFETY BRACKET - 1

1G

BLACK 9/16" LARGE HEAD SCREW - 36

1S

WASHER - 12

10I

BLACK 2-1/4" FLAT HEAD SCREW - 7

26S

7F

TWIST-LOCK

®

FASTENER - 10

SILVER 1/4" MACHINE SCREW - 12

61S

3S

GOLD 5/16" FLAT HEAD SCREW - 48

CAM SCREW - 12

8F

WOOD DOWEL - 2

15F

NAIL - 39

1N

HIDDEN CAM - 12

1F

PULL - 6

98K

BLACK 1-15/16" FLAT HEAD SCREW - 2

113S

40DA

UNIVERSAL CABINET RAIL - 12

40DC

DRAWER RIGHT - 6

40DD

DRAWER LEFT - 6

LARGE DRAWER

FRONT BRACKET - 4

9G

DRAWER FRONT

BRACKET - 2

8G

METAL BRACKET - 3

4G

30S

BLACK 1-9/16" FLAT HEAD SCREW - 30

FELT DISC

CARD - 1

1M

Step 1

Look for this icon. It means a

video assembly tip is available at

www.sauder.com/service/tips

å

Assemble your unit on a carpeted ﬂ oor or on the empty

carton to avoid scratching your unit or the ﬂ oor.

å

To begin assembly, push a SAUDER TWIST-LOCK®

FASTENER (7F) into the large holes in the ENDS (A

and B) and UPRIGHT (C).

å

Repeat this step for the BOTTOM (E).

419517www.sauder.com/service

Page 5

7F

Do not tighten the TWIST-LOCK® FASTENERS in this step.

A

B

C

(10 used)

Step

å

Push twelve HIDDEN CAMS (1F) into the ENDS (A and B)

and DRAWER BRACES (M65).

Step 2

419517 www.sauder.com/servicePage 6

A

B

Arrow

The arrow in the HIDDEN

CAM must point toward the

hole in the edge of the board.

Hole

Just think. The sooner

you do this, the sooner

you do something else.

Surface with

TWIST-LOCK®

FASTENERS

Surface with

TWIST-LOCK®

FASTENERS

1F

Arrow

1F

Arrow

M65

Arrow

1F

(12 used)

Step

419517www.sauder.com/service

Page 7

Step 3

å

Turn twelve CAM SCREWS (8F) into the FRONT LEGS (H)

and DRAWER FRONTS (J, K, L, and M).

8F

(12 used)

J

L

K

M

H

M

L

Step 4

å

Insert a WOOD DOWEL (15F) into the indicated holes in the FRONT LEG (H).

å

Fasten the RIGHT END (A) to the FRONT LEG (H). Tighten three HIDDEN CAMS.

å

NOTE: Be sure the WOOD DOWEL in the LEG inserts into the RIGHT END.

å

Fasten a BACK LEG (I) to the RIGHT END (A) as shown in the lower diagram. Use

three BLACK 2-1/4" FLAT HEAD SCREWS (26S).

419517 www.sauder.com/servicePage 8

1

2

A

H

Surface with

TWIST-LOCK®

FASTENERS

These surfaces should be even.

15F

The LEG will

overhang

this edge.

The LEG will

overhang

this edge.

I

These surfaces should be even.

BLACK 2-1/4" FLAT HEAD SCREW

(3 used in this step)

26S

å

Insert the WOOD DOWEL (15F) into the indicated hole in the FRONT LEG (H).

å

Fasten the LEFT END (B) to the FRONT LEG (H). Tighten three HIDDEN CAMS.

å

NOTE: Be sure the WOOD DOWEL in the LEG inserts into the LEFT END.

å

Fasten the BACK LEG (I) to the LEFT END (B) as shown in the lower diagram. Use

three BLACK 2-1/4" FLAT HEAD SCREWS (26S).

Step 5

419517www.sauder.com/service

Page 9

15F

B

H

Surface with

TWIST-LOCK®

FASTENERS

These surfaces should be even.

The LEG will

overhang

this edge.

I

BLACK 2-1/4" FLAT HEAD SCREW

(3 used in this step)

26S

The LEG will

overhang

this edge.

Step 6

419517 www.sauder.com/servicePage 10

1

2

3

4

1

2

3

4

1

2

3

4

1

2

3

4

GOLD 5/16" FLAT HEAD SCREW

(12 used in this step)

3S

A

B

Surface with

TWIST-LOCK®

FASTENERS

Surface with

TWIST-LOCK®

FASTENERS

å

Fasten six UNIVERSAL CABINET RAILS* (40DA) to the

ENDS (A and B). Use twelve GOLD 5/16" FLAT HEAD

SCREWS (3S) through holes #1 and #4.

å

*patent pending glide system

Glide end

1

2

3

4

1

2

3

4

VIEW THE DRAWER GLIDE VIDEO

Step 7

419517www.sauder.com/service

Page 11

1

2

3

4

1

2

3

4

1

2

3

4

1

2

3

4

1

2

1

2

Surface with

TWIST-LOCK®

FASTENERS

C

GOLD 5/16" FLAT HEAD SCREW

(12 used in this step)

3S

å

Fasten six UNIVERSAL CABINET RAILS* (40DA) to

the UPRIGHT (C). Use twelve GOLD 5/16" FLAT HEAD

SCREWS (3S) through holes #1 and #4.

å

*patent pending glide system

Glide end

Finished edge

VIEW THE DRAWER GLIDE VIDEO

Step 8

419517 www.sauder.com/servicePage 12

å

Fasten the LEFT END (B) to the TOP (D). Tighten two

TWIST-LOCK® FASTENERS.

How to use the SAUDER TWIST-LOCK

®

FASTENER

1. Insert the dowel end of the FASTENER into the

hole of the adjoining part.

NOTE: The dowel end of the FASTENER must

remain fully inserted in the hole of the adjoining

part while locking the FASTENER.

2. Tighten the FASTENER with a Phillips

screwdriver as tight as possible.

Dowel end

B

Surface with

TWIST-LOCK®

FASTENERS

H

D

Surface with holes

Finished edge

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Caution

å

Fasten the UPRIGHT (C) to the TOP (D). Tighten two

TWIST-LOCK® FASTENERS.

Step 9

419517www.sauder.com/service

Page 13

C

Finished edge

Don't worry. It isn't

Rome. This can be built

in a day.

Surface with

TWIST-LOCK®

FASTENERS

D

Step 10

å

Fasten the BOTTOM (E) to the LEFT END (B). Tighten two

TWIST-LOCK® FASTENERS.

å

Fasten the BOTTOM (E) to the UPRIGHT (C). Use two

BLACK 1-15/16" FLAT HEAD SCREWS (113S).

å

Slide the BOTTOM MOLDING* (O) onto the notched edge

of the BOTTOM (E).

å

*U.S. Patent No. 5,499,886

419517 www.sauder.com/servicePage 14

C

E

O

Notched edge

Surface with

TWIST-LOCK®

FASTENERS

B

BLACK 1-15/16" FLAT HEAD SCREW

(2 used in this step)

113S

The groove is

closer to this edge.

å

Fasten the RIGHT END (A) to the TOP (D) and BOTTOM (E).

Tighten four TWIST-LOCK® FASTENERS.

å

Fasten the METAL BRACKETS (4G) to the ENDS (A and B) and

UPRIGHT (C). Use three BLACK 9/16" LARGE HEAD SCREWS (1S).

å

Fasten the FRONT MOLDING (N) to the ENDS (A and B) and

UPRIGHT (C). Use three BLACK 9/16" LARGE HEAD SCREWS (1S)

through the BRACKETS and into the MOLDING.

Step 11

419517www.sauder.com/service

Page 15

N

C

B

A

Surface without

TWIST-LOCK®

FASTENERS

H

E

D

BLACK 9/16" LARGE HEAD SCREW

(6 used in this step)

1S

4G

Step 12

å

Carefully turn your unit over onto its front edges. Unfold

the BACK (F) and lay it over your unit.

å

First, make equal margins along the top and bottom

edges of the BACK (F). Then, make equal margins along

the side edges of the BACK (F). Push on opposite corners

of your unit if needed to make it "square".

å

Fasten the BACK (F) to your unit using the NAILS (1N).

å

NOTE: Be sure to tap NAILS into the holes that line up

over the UPRIGHT (C).

å

Peel the FELT DISC from the FELT DISC CARD (1M). Stick

the FELT DISC on the LEGS (H and I).

419517 www.sauder.com/servicePage 16

NAIL

(39 used in this step)

1N

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Caution

These holes must line up

over the UPRIGHT (C).

F

I

H

I

H

1M

å

Fasten the FOOT BRACKET (6E) to the BOTTOM (E). Use

three BLACK 9/16" LARGE HEAD SCREWS (1S).

å

Slide the FEET (P) onto the FOOT BRACKET (6E).

å

Slide the CORNER CAP (5E) onto the FEET (P).

å

Turn two BLACK 9/16" LARGE HEAD SCREWS (1S) into

the short slots of the FOOT BRACKET (6E).

Step 13

419517www.sauder.com/service

Page 17

E

P

6E

5E

6E

Completed foot support

BLACK 9/16" LARGE HEAD SCREW

(5 used in this step)

1S

Step 14

419517 www.sauder.com/servicePage 18

D975

D50

D51

D167

D50

D51

VIEW THE T-SLOT BOX VIDEO

L

M65

L

1

3

2

4

Push down

å

Pull the DRAWER FRONT BRACKETS (9G) apart and slide them

into the grooves in the DRAWER SIDES (D50 and D51). You may

need to gently tap them in with a hammer.

å

NOTE: The DRAWER FRONT BRACKETS are marked "RH" and

"LH" for easy identiﬁ cation.

å

Fasten a DRAWER FRONT (L) to the DRAWER FRONT

BRACKETS (9G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S).

å

Slide the DRAWER BOTTOM (D975) into the

grooves in the DRAWER SIDES (D50 and D51) and

DRAWER FRONT (L).

å

Fasten the DRAWER BRACE (M65) to the DRAWER

FRONT (L). Tighten one HIDDEN CAM.

å

Fasten the DRAWER BACK (D167) to the DRAWER

SIDES (D50 and D51) and DRAWER BRACE (M65).

Use ﬁ ve BLACK 1-9/16" FLAT HEAD SCREWS (30S).

å

Repeat this step for the other three drawers using

DRAWER FRONTS (L and M).

BLACK 9/16" LARGE HEAD SCREW

(16 used in this step)

1S

Be sure the

DRAWER

BOTTOM

inserts into

the DRAWER

BACK groove.

With the palm of your hand,

tap the DRAWER BOTTOM

down into the groove.

30S

Start each screw a few turns before

completely tightening any of them.

BLACK 1-9/16" FLAT HEAD SCREW

(20 used in this step)

Unﬁ nished surface

Surface with

HIDDEN CAM

9G

Hidden part using

recycled material.

Color may vary.

Step 15

419517www.sauder.com/service

Page 19

VIEW THE T-SLOT BOX VIDEO

D212

D166

D213

D975

D166

J

M65

1

3

2

4

Push down

å

Pull the DRAWER FRONT BRACKETS (8G) apart and slide them

into the grooves in the DRAWER SIDES (D212 and D213). You

may need to gently tap them in with a hammer.

å

NOTE: The DRAWER FRONT BRACKETS are marked "RH" and

"LH" for easy identiﬁ cation.

å

Fasten the DRAWER FRONT (J) to the DRAWER FRONT

BRACKETS (8G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S).

å

Slide the DRAWER BOTTOM (D975) into the grooves in the

DRAWER SIDES (D212 and D213) and DRAWER FRONT (J).

å

Fasten the DRAWER BRACE (M65) to the DRAWER

FRONT (J). Tighten one HIDDEN CAM.

å

Fasten the DRAWER BACK (D166) to the DRAWER

SIDES (D212 and D213) and DRAWER BRACE (M65).

Use ﬁ ve BLACK 1-9/16" FLAT HEAD SCREWS (30S).

å

Repeat this step for the other drawer.

BLACK 9/16" LARGE HEAD SCREW

(8 used in this step)

1S

Be sure the

DRAWER

BOTTOM

inserts into

the DRAWER

BACK groove.

With the palm of your hand,

tap the DRAWER BOTTOM

down into the groove.

30S

Start each screw a few turns before

completely tightening any of them.

BLACK 1-9/16" FLAT HEAD SCREW

(10 used in this step)

Unﬁ nished surface

Surface with

HIDDEN CAM

8G

Hidden part using

recycled material.

Color may vary.

Step 16

419517 www.sauder.com/servicePage 20

L

D51

D50

98K

SILVER 1/4" MACHINE SCREW

(12 used for the PULLS)

61S

10I

If you're doing this to

help a friend, don't

leave without a bite.

å

Fasten a DRAWER RIGHT (40DC) to the LOWER RIGHT

DRAWER SIDE (D50) and a DRAWER LEFT (40DD) to the

LOWER LEFT DRAWER SIDE (D51). Use four GOLD 5/16"

FLAT HEAD SCREWS (3S) through holes #1 and #2.

å

NOTE: The glides are not intended to rotate.

å

Fasten a PULL (98K) to the LOWER RIGHT DRAWER

FRONT (L). Use two WASHERS (10I) and two SILVER 1/4"

MACHINE SCREWS (61S).

å

Repeat this step for the other drawers.

1

2

GOLD 5/16" FLAT HEAD SCREW

(24 used in this step)

3S

Glide end

1

2

VIEW THE DRAWER GLIDE VIDEO

La page est en cours de chargement...

Sauder 419517 Mode d'emploi

Sauder 419517 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents