Pentair Hydromatic FG-3100RF Battery Backup System Le manuel du propriétaire

Marque: Pentair Hydromatic

Modèle: FG-3100RF Battery Backup System

Catégorie: Pompes à eau

Taper: Le manuel du propriétaire

Ce manuel convient également à

FG-3100RF

pentair.com

INSTALLATION AND

OPERATION MANUAL

Pump Activity

Activité de pompe

Actividad de la bomba

System Alert

Alerte du système

Alerta del sistema

AC Power

Courant AC

Charging

Recharge

En carga

Battery Status

État de batterie

Estado de la batería

Alarm Silenced

Alarme arrêtée

Alarma apagada

Test System

Tester

Probar sistema

Silence Alarm

Arrêter l’alarme

Apagar alarma

Light

Lumière

Luz

Circuit Breaker

Disjoncteur

Disyuntor

Pump

Pompe

Bomba

Float Switch

Interrupteur à otteur

Interruptor del otador

Power

Courant

Encendido

Reset System

Réinitialise

Restrablecer sistema

BATTERY BACKUP SYSTEM

FG-3100RF

ENGLISH: 1-17  FRANCAIS: 18-34  ESPANOL: 35-51

PRODUCT DISCONTINUED. FOR REFERENCE ONLY.

HYD979 (06-08-20)

TABLE OF CONTENTS

SECTION ................................................................................................................................................................................................ PAGE

Safety Information ............................................................................................................................................................................... 3

General Information ............................................................................................................................................................................4

Internet And Alerts Setup .....................................................................................................................................................................5

Installation ..........................................................................................................................................................................................6

Battery Requirements ........................................................................................................................................................................ 10

Wiring And Setup ................................................................................................................................................................................ 11

Charger/Controller Display ..................................................................................................................................................................13

Troubleshooting ..................................................................................................................................................................................15

Parts List ............................................................................................................................................................................................16

Warranty .............................................................................................................................................................................................17

HYD979 (06-08-20)

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS - This manual contains important

instructions that should be followed during installation,

operation, and maintenance of the product.

This is the safety alert symbol. When you see this symbol

on your pump or in this manual, look for one of the following

signal words and be alert to the potential for personal injury!

indicates a hazard which, if not avoided, will

result in death or serious injury.

indicates a hazard which, if not avoided, can

result in death or serious injury.

indicates a hazard which, if not avoided, can or

may result in minor or moderate injury.

NOTE: Addresses practices not related to personal injury.

 Keep safety labels in good condition. Replace missing or

damaged safety labels.

 To avoid risk of serious bodily injury due to electrical shock

or burns and property damage due to flooding, carefully

read the safety instructions in this manual and on the

pump before installing pump.

 Battery acid is corrosive. Do not spill on

skin, clothing, or battery charger. Wear eye and head

protection when working with battery. Connect and

disconnect DC output terminals only after removing the

charger from the AC outlet. Never allow the DC terminals to

touch each other.

 Hazardous Voltage. Can cause severe or

fatal electrical shock. Do not plug in or unplug battery

charger while standing on a wet floor or in water. Be sure

one hand is free when plugging in or unplugging charger. If

basement floor is wet, disconnect power to basement

before walking on floor.

 Risk of flooding. Do not run pump dry.

To do so will damage seals and can cause leaking

and property damage.

 Follow local and/or national plumbing and electrical

codes when installing the system. A ground fault circuit

interrupter (GFCI) is recommended for use on any

electrical appliance submerged in water.

 Use this system only for backup sump pump duty in a

residential application. It is not designed as a primary

sump pump.

 Do not lift pump by electrical cord.

 Risk of electrical shock. Do not lift the

pump by the electrical cord; lift pump only by the

discharge pipe, lifting ring or handle on the pump. Lifting

by the cord can damage the cord.

 Pump clear water only with this pump.

 Pump is permanently lubricated at the factory. Do not try

to lubricate it!

 Keep battery charger and battery box off of the floor and

in a dry, cool, well ventilated area.

 NOTE: If a Carbon Monoxide (CO) sensor is installed, it

must be at least 15 feet away from battery charger in

order to avoid nuisance CO alarms. Please refer to your CO

detector’s installation guidelines for more information.

 To avoid danger of fire or explosion, keep sparks and flame

(pilot light) away from battery.

 Maximum vertical pumping distance is 15 feet (4.6M) for

Model FPDC30.

 Make sure sump is clear of debris. Debris can damage the

pump which can result in flooding.

California Proposition 65 Warning

This product and related accessories contain

chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm.

SAFETY INFORMATION

HYD979 (06-08-20)

GENERAL INFORMATION

The battery backup sump system is not a substitute for your

primary sump pump. It is designed to temporarily backup your

primary sump pump during a power outage or other problem

which prevents normal operation of the primary pump. Do not

use this system to pump flammable liquids or chemicals. Pump

clear water only with this pump.

Keep the battery charger dry and protected from damage.

This system is designed to work with a deep cycle sealed

maintenance free lead-acid AGM battery. It will also work with

a flooded lead acid battery. Gel and Sealed flooded lead acid

batteries are not recommended.

In an emergency (such as an extended power outage) which

depletes the system deep cycle battery, your automobile

battery may be temporarily substituted. Be sure to replace the

system deep cycle battery as soon as possible.

Use of an automobile battery instead of a deep cycle battery

in this system will significantly reduce the system’s total

performance. Automobile batteries are not designed for this

type of application and will be quickly ruined by the repeated

charge/discharge cycling.

NOTE: This system is not designed for applications involving salt

water, brine, or where fish may be present! Use with these will

void warranty.

BASIC TOOLS AND PARTS NEEDED (PURCHASE SEPARATELY)

 Tongue and groove, or large adjustable pliers

 Tape measure

 Socket wrench or 5/16” nut driver

 Side cutters

 Hacksaw (to cut PVC pipe)

 Medium size pliers

 Slotted screwdriver

 Phillips head screwdriver

 Pencil or marker

 PTFE pipe thread sealant tape

 PVC glue (solvent weld)

 PVC pipe cleaner

 Cloth towel

 Plastic fittings

 Check valve(s) - 1 or 2 depending on installation

 38-120 Ampere-Hour Storage or Deep Cycle Battery

REQUIRED BATTERY CAPACITY

For best results, use the following AGM Storage Batteries.

Part Amp-Hour

Gal/Charge

at 10’

Approx Run

Time

BAT40 40 4,800 5 Hours

 Unit equipped with dual battery capability

 Maximum amp-hour: 120

NOTE: The charger will not fully charge batteries with excessive

amp hour ratings without resetting system.

PERFORMANCE

HEAD IN FT 0 5 10 15

HEAD IN METERS 0 1.5 3 4.6

GPM 45 34 21 0

LPM 170 129 80 0

BATTERY BACKUP SYSTEM (BBU) INSTALLATION AND OPERATION

 Install this system during a time when the primary pump will not

be needed.

 Gather all supplies before starting.

 Read all warnings and installation steps before you start.

 Be prepared for water to leak from the coupling or piping when

disassembling or cutting the discharge pipe. Protect system

components, tools and supplies from getting wet. Dry any work

areas that get wet.

 Study pages 5-8 to determine which installation method will be

best for you. The “Separate Discharge” (Figure 2), installation is

recommended.

 NOTE: Check your local codes and ordinances regarding waste

water disposal (especially when running the pump discharge

outside the house) before you start. The installation must

conform to all legal requirements.

 If possible, install the BBU so that the discharge goes directly

outdoors (separate discharge pipe from the primary sump pump

discharge pipe). If this is not a practical option, see the “Common

Discharge” (Figure 3) option.

 For ALL installations, once the installation is complete, run

both the primary sump pump and the BBU through at least one

complete cycle to make sure that everything operates correctly.

GENERAL INFORMATION

Figure 1: Mark Pipe at ‘Start’ Water Level

6781 0916

HYD979 (06-08-20)

INTERNET AND ALERTS CONFIGURATION

INTERNET CONNECTION AND ALERTS CONFIGURATION

1. Complete the Battery Backup Registration, Internet

Connection and Alert Configuration BEFORE connecting

the battery and AC power supply to your BBU.

NOTE: If you have already connected the battery and

AC power supply to the BBU before connecting to to the

internet, complete the device registration process.

Then disconnect the battery and remove the AC power

supply from the BBU panel and gateway for 2 minutes in

order to reset the panel. Resume with Step 8.

2. Download the Pentair Home app to your mobile device

from the App Store® or Google Play™ Store.

3. Open the app.

 EXISTING USERS: LOGIN to your account.

 NEW USERS: Scroll down in the App and click SIGN

UP.

4. Enter a valid EMAIL and PASSWORD.

5. Select TERMS OF SERVICE.

6. Click CREATE AN ACCOUNT.

7. Complete instruction in the VERIFICATION EMAIL

8. LOGIN to your account.

9. Register your device using the Unique Device ID Key

included on the device and your manual cover.

10. The Alerts will use the e-mail(s) and phone number(s)

entered here.

11. Find an open network connection on your internet router

or other hardwired connection (like an internet switch).

12. Rotate the Gateway antenna up on the gateway. Using

the supplied 1 meter Ethernet cable (or a longer cable if

necessary)

13. Connect the Gateway to the open internet port

14. An uninterrupted power supply for your internet modem,

home router and the gateway power supply is recommended.

15. Connect the Gateway power supply to a 115 VAC outlet, plug

the cord into the back of the Gateway.

 The Gateway will blink red for a few seconds.

 When the LED becomes solid Green or solid Green with

an occasional blink – your Gateway is communicating with

the Link2O server. If not, refer to Gateway Trouble in the

manual.

16. Connect the red positive (+) charger/controller lead wire to the

positive (+) (red) battery terminal.

17. Connect the black negative (-)charger/controller lead wire to

the negative (-) (black) battery terminal.

18. Connect the Charger Power Supply cable (supplied) to the

Charger/Controller’s Power input jack. Plug the other end into

a 115 VAC outlet.

19. Check the AC power LED on the Controller. If it is solid green

the unit is communicating with the web site.

20. Verify the system is operational by pressing the TEST

SYSTEM button and observing the test sequence.

21. Test communication by clicking the Test icon on the web page

and verify the unit has run the test.

22. Using the drop down menu, configure the desired method of

Alerts you want to receive: text or email.

23. Alerts can be tested by activating the pump with thefloat

switch.

Gateway Status Definition Action Needed

Green Power on. Gateway connected to servers. OK - Connection complete and operational

Green, quick blink Power on. Data trac to servers. OK - Operating, data is moving between BBU and server

Green, slow blink

(1-2 blinks per second)

Power on. Gateway connected to local router, but not

connected to Internet or servers.

System is online and scanning for destination/server

(add a network switch inline to help dene unit).

Red Power on. Gateway has no local connection to

router. The gateway does not recognize/see that it is

connected to the router.

Check Ethernet cable connections and/or quality or

cable. Try a different router port. Is the router turned on.

Red, slow blink

(1-2 blinks per second)

Power on. Gateway communicating with router, but

router cannot assign Dynamic Host Conguration

Protocol (DHCP) or Domain Name System (DNS) to

gateway.

Router is not permitting the gateway to access the

internet (add a network switch inline to help dene unit).

Off Power off or product fault. Check power source, verify power adapter is

functioning. Defective gateway.

Table I: Gateway Troubleshooting

HYD979 (06-08-20)

INSTALLATION

INSTALLATION (TYPICAL): SEPARATE DISCHARGE

Unplug the primary sump pump before beginning this

procedure.

Risk of electrical shock. Can shock, burn, or kill.

1. Allow for overlap when cutting piping and run a trial (dry)

fitting before you glue.

2. Use PTFE pipe thread sealant tape on male ends of

discharge pipe. Thread the 1-1/4” x 1-1/2” elbow (supplied)

onto the discharge. When tight, the elbow must point up.

3. If possible, install the Battery Backup Unit (BBU) on

the floor of the sump. Be sure that the two pumps do

not touch each other and do not interfere with switch

operation.

NOTE: If debris or gravel is present in the bottom of the

sump pit that could get sucked up into the pump, set

both the primary sump pump and the BBU up on bricks or

cinder blocks to prevent clogging.

4. If the sump is too small to allow both pumps to sit on

the bottom of the sump, install an angle bracket on the

primary sump pump’s discharge pipe with stainless steel

hose clamps.

Mount the backup pump on the angle bracket (Figure 2).

5. Cut a piece of 1-1/2” PVC pipe to reach from the backup

pump discharge elbow to about one (1) foot above the

basement floor. This is the lower discharge pipe.

6. To prevent airlocking the pump during operation, drill a

1/8” hole in the lower discharge pipe about 2” above the

bottom of the pipe (below floor level).

7. Install FP0026-10 check valve (purchase separately) on

the upper end of the pipe.

Tighten the hose clamps securely. BE SURE that the flow

arrows point UP (away from the BBU). If they point down,

the valve will not pass water and the pump will not work.

8. Cut a short length of 1-1/2” PVC pipe for a riser pipe and

clamp it into the top of the check valve.

9. Install a U74-68 Hose and Clamp Assembly (sold

separately) on the top of the riser pipe. For 1-1/2” pipe,

remove and discard the short piece of 1-1/4” hose in the

Hose and Clamp Assembly. Leave the hose clamps loose

and slide the Assembly down below the top of the riser

pipe.

10. Determine where you want the discharge to exit the

basement. At that point, drill the necessary holes (large

enough to have clearance for a 1-1/2” pipe) to allow you

to run the discharge pipe from above the sump to the

outdoors.

11. Install the horizontal discharge pipe. Install a 90° elbow on

the inside end but do not glue.

12. Cut another short piece of 1-1/2” PVC for the Upper

Discharge Pipe to run from the top of the riser pipe up to

the 90° elbow. Be sure to allow enough overlap for the glue

joint in the elbow.

13. Do a trial fit with NO GLUE, installing the 1-1/2” upper

discharge pipe in the 90° elbow and the upper discharge

pipe in the vertical end of the 90° elbow.

The upper discharge pipe should just fit between the riser

pipe and the elbow.

14. Whenever using PVC primer and PVC cement, follow the

glue manufacturer’s instructions. Risk of

fire and chemical inhalation.

15. Make sure that the BBU clears the primary sump pump

and its switch. If there isn’t room for both pumps to sit

on the floor of the sump, the BBU will have to be raised

(depending on your particular situation).

16. Clean, prime and glue the upper discharge pipe into the

90º elbow. When the glue has set, slide the Hose and

Clamp Assembly up to cover the joint and tighten all the

hose clamps.

17. Install the Battery Backup Switch as shown, 1” above start

water level of primary pump. Fasten it to the pipe with

cable ties.

18. Tape the pump cord to the riser pipe so that the plug

cannot fall into the sump.

19. Go to BBU WIRING AND SETUP section of this manual for

wiring instructions.

20. Once all wiring is complete, fill your pit with water and

verify that the primary sump pump removes the water and

the BBU doesn’t run.

21. Then, unplug your primary sump pump and refill your pit

with water. Verify that the BBU pump removes the water.

22. Make sure that the power is on to both pumps, and your

system is ready to use.

HYD979 (06-08-20)

INSTALLATION

Figure 2: Separate Discharge - Typical Installation

NOTE: Check valve flapper(s) must swing AWAY and flow arrow(s) must point AWAY from pump being protected.

The water level when the switch shuts off must be above the BBU pump intake.

“Separate Discharge”

NOTICE:

Check Valve Flapper(s) must swing AWAY and flow arrow(s) must point

AWAY from pump being protected.

The water level when the switch shuts off must be above the BBU

pump intake.

* Supplied with the Battery Backup System.

Items in italics must be purchased separately.

FLOW

Slope DOWN

to outlet Sill

FP0026-10

Check Valve

(Purchase

Separately)

PTFE pipe thread

sealant tape on all

threaded joints

1-1/2” PVC Riser Pipe

(cut to fit)

1-1/4” FNPTx1-1/2” Slip

Elbow*

Battery Back Up

Sump Pump*

Lower Discharge Pipe

1-1/2” PVC Pipe

(cut to fit)

Primary Sump Pump

Check Valve

Flow Arrow; Must point

AWAY from Pump

being Protected

1-1/2” PVC Upper

Discharge Pipe

(cut to fit)

Battery Backup

Switch*

If the sump is small,

hang the BBU from

the Primary discharge

pipe on an angle bracket.

Floor

Joist

U74-68 Hose and

Clamp Assembly

(Purchase Separately)

Drill 1/8” Anti-Airlock

Hole

6782 0313a

Not to scale.

Wiring omitted for clarity.

HYD979 (06-08-20)

INSTALLATION

INSTALLATION (TYPICAL): COMMON DISCHARGE

Unplug the primary sump pump before beginning this

procedure. Risk of electrical shock. Can shock,

burn, or kill.

1. Allow for over lap when cutting piping and run a trial (dry)

fitting before you glue.

2. If there is no check valve in the primary sump pump’s

discharge, you will need to install one. You must also

install one in the BBU’s discharge pipe (Figure 3). Make

sure that the check valve flow arrow points AWAY from the

pump it is protecting.

3. Use PTFE pipe thread sealant tape on male ends of

discharge pipe. Thread the 1-1/4” x 1-1/2” elbow (supplied)

onto the discharge. When tight, the elbow must point up.

4. If possible, position the BBU on the floor of the sump; be

sure that the two pumps do not touch each other and do

not interfere with switch operation.

NOTE: If debris or gravel is present in the bottom of the

sump pit that could get sucked up into the pump, set

both the primary sump pump and the BBU up on bricks or

cinder blocks to prevent clogging.

5. If the sump is too small to allow both pumps to sit on the

bottom of the sump, find a raised position that doesn’t

interfere with the primary sump pump switch.

6. Cut a piece of 1-1/2” PVC pipe to reach from the backup

pump discharge elbow to about one (1) foot above the

basement floor. This is the lower discharge pipe.

7. To prevent airlocking the pump during operation, drill a

1/8” hole in the lower discharge pipe about 2” above the

bottom of the pipe (below floor level).

8. Install FP0026-10 check valve (sold separately) on the

upper end of the pipe. Tighten the hose clamps securely.

BE SURE that the flow arrows point UP (away from the

backup pump). If they point down, the valve will not pass

water and the pump will not work.

9. Cut the discharge pipe for the primary sump pump above

the union and check valve (if any). Make this cut about

18” above the top of the BBU’s riser pipe with the backup

pump sitting as installed.

10. If the primary sump pump does not have a check valve

installed in the discharge pipe, install one now.

11. Cut a length of discharge pipe for the primary sump pump

to fit between the check valve and a 45° slip wye. Be sure

to allow for the overlap needed for gluing joints.

12. Install the 45° wye on the primary sump pump’s discharge

pipe.

13. Install a 45° elbow on the 1-1/2” BATTERY BACKUP

discharge pipe.

14. Fit the upper discharge pipe to the upper end of the wye.

NOTICE: It is good practice to cut a short length of pipe to

go into the wye and install a union on the pipe. Continue

the discharge pipe from the outlet side of the union.

This will allow easier removal of the system for cleaning

or service. A U74-68 Hose and Clamp Assembly (sold

separately) can be used for this.

15. Make sure that the BBU will clear the primary sump pump

and its switch. If there isn’t room for both pumps to sit

on the floor of the sump, the BBU will have to be raised

(depending on your particular situation).

16. Do a trial assembly to make sure that everything is

going to fit. This may require a helper to assist in holding

everything together while you check the fit without glue.

Mark all joints before gluing.

Follow the glue manufacturer’s instructions regarding fire

hazards and ventilation when using PVC solvents, primer,

and cement. Risk of fire and chemical

inhalation.

17. Take all the pipe apart, clean all joints, and then

reassemble the system, gluing it with PVC primer and

glue.

18. Install the Battery Backup Switch as shown, 1” above start

water level of primary pump. Fasten it to the pipe with the

cable ties provided.

19. Tape the pump cord to the riser pipe so that the plug

cannot fall into the sump.

20. Go to BBU WIRING AND SETUP section of this manual for

wiring instructions.

21. Once all wiring is complete, fill your pit with water and

verify that the primary sump pump removes the water and

the BBU doesn’t run.

22. Then, unplug your primary sump pump and refill your pit

with water. Verify that the BBU pump removes the water.

23. Make sure that the power is on to both pumps, and your

system is ready to use.

HYD979 (06-08-20)

INSTALLATION

Battery Backup

Switch*

Primary Pump

Discharge Pipe

(cut to fit)

Primary Sump Pump

Discharge Port

Primary Pump

Check Valve

Flow Arrow; Must point

AWAY from Pump

being Protected

45º Slip Elbow

PTFE pipe thread

sealant tape on all

threaded joints

1-1/4” FNPTx1-1/2”

Slip Elbow*

Battery Back Up

Sump Pump*

Thread to Slip

Adapter

45 degree Slip Wye

FLOW

Optional 1-1/2”

PVC Pipe (cut to fit)

1-1/2” PVC Pipe

(cut to fit)

Lower Drischarge Pipe

1-1/2” PVC Pipe

(cut to fit)

AlternateWye/Elbow

Setup

45º Slip Street

Elbow

FLOW

“Common Discharge”

NOTICE: In this installation, if the Primary Sump Pump (PSP) does not have a

check valve installed below the wye, you MUST install a check valve for the PSP

as shown. This prevents backflow of water into the sump from the Battery Backup

System. Check Valve Flapper(s) must swing AWAY and flow arrow(s) must point

AWAY from the pump being protected.

The water level when the switch shuts off must be above the BBU pump intake.

Supplied with the Battery Backup System.

Items in italics must be purchased separately

Typical installation,

assembled.

Both check valves

must be installed

on the pump side

of the wye.

FP0026-10

Check Valve

(Purchase

Separately)

1-1/2” PVC Riser Pipe

(cut to fit)

1-1/2” PVC Upper

Discharge Pipe

(cut to fit)

Flow Arrow; Must point

AWAY from Pump

being Protected

U74-68 Hose and

Clamp Assembly

(Purchase Separately)

Drill 1/8”

Anti-Airlock Hole

6783 0313a

Not to scale.

Wiring omitted for clarity.

Figure 3: Common Discharge Pipe - Typical Installation

 In this installation, if the primary sump pump does not have a check valve installed below the wye, you MUST

install a check valve for the primary sump pump as shown. This prevents backflow of water into the sump from

the battery backup system.

 Check Valve Flapper(s) must swing away and flow arrow(s) must point away from the pump being protected.

 The water level when the switch shuts off must be above the BBU pump intake.

HYD979 (06-08-20)

BATTERY REQUIREMENTS

Install the battery in the battery case. To prevent accidental

shorting across battery terminals, close and latch the battery

case securely. Do not leave the battery uncovered.

Hazardous electric current. Can cause severe

burns and start a fire if the battery terminals are short

circuited.

Do not allow children to play around the battery backup

system installation.

The performance of your backup sump pump depends on

the battery used with it for power. We recommend using

our BAT40. You can also use a group 24M or 27M Deep Cycle

battery. They will provide acceptable performance and will

stand up well to long periods of little or no use.

This system is designed to work with either a sealed lead-acid

AGM battery or a flooded lead-acid battery. Use of a true Gel

Cell (often confused for AGM) or a standard automotive battery

with this charger is not recommended. An automotive battery

may require charging after only 1-2 hours of continuous use,

and the repeated charging cycles may cause early plate failure

in the battery.

 Use only lead-acid batteries. This unit is not designed to

use with Li-Ion, NiMh, NiCAD, Liquid Polymer, etc.

 Use only the recommended battery or one of the same

type and size so it will fit in the battery box (maximum size:

13” long x 7” wide x 10” tall (330.2mm x 177.8mm x 254mm)

including terminals) and supply enough voltage for full

performance.

BATTERY MAINTENANCE

 To protect the battery case from chipping and gouging, do

not let the battery sit on a concrete floor.

 Install the battery on a shelf or protective pad (plywood,

2x4s, etc.).

 Always install the battery in a dry location that is

protected from flooding.

Severe burn hazard. An acid-filled standard

lead-acid battery contains sulfuric acid. Avoid contact with

skin, eyes or clothing.

PRE-QUALIFICATION TEST – 1 AND 2

Charger is charging at a very low level to try to bring a dead

battery back to life.

If the battery is taking too long, try resetting the charger once

or twice (push the System Test and Silence Alarm buttons

together to reset the charger).

SPECIAL FEATURES

The charger is equipped with reverse battery, short circuit,

and “runaway charge” protection.

POSSIBLE PROBLEMS AND REMEDIES

1. Wrong Battery Voltage: Reconnect charger to a 12 volt

battery.

2. Reversed Battery Connections: Check all connections.

The negative (black) on the battery must connect to the

negative (black) on the charger, and the positive (red)

on the battery must connect to the positive (red) on the

charger. Reversing the battery connections will cause the

System Alert and Silenced Audible Alarm LEDs to flash.

3. Thermal Runaway Condition: “Thermal Runaway” is the

technical term for the condition of the battery when some

(or all) of the cells have deteriorated to the point that they

won’t take a charge. In this case, replace the battery.

4. Charge Time Monitor – 1 and 2: Battery took too long to

complete its charge. The Charge Time Monitor will shut

down the charger after 84 hours of continuous charging.

Possible causes are:

 Pump ran for a long period of time during charging, or

 Battery is too large for the charger (including several

batteries connected in a parallel circuit).

EXCESSIVE BATTERY DRAIN

Pump may have run for a very long time, discharging the

battery.

1. If 115VAC power is OFF, the charger shuts down until the

power comes back on, but the pump will run as long as the

battery charge lasts. You may need to replace the battery

afterwards.

2. If 115VAC power is ON, the charger/controller continues to

try to charge the battery at a charging rate of .5 AH until

the battery charge is more than 20%, at which point the

charger will resume charging at a rate of 2 AH.

3. If the pump is running and the AC power is on, you may

need to stop the pump to allow the battery to charge.

Follow the battery manufacturer’s recommendations for

maintenance and safe use of the battery.

HYD979 (06-08-20)

WIRING AND SETUP

1. Connect the positive (+) charger/controller lead wire (red)

to the positive (+) battery terminal (red).

2. Connect the negative (–) charger/controller lead wire

(black) to the negative (–) terminal (black) on the battery.

3. If you are using two batteries, use the set of optional

terminals and connect the second battery. Use lead

wires (not included) to connect the positive (+) charger/

controller terminal to the positive (+) battery terminal and

the negative (–) charger/controller terminal to the negative

(–) battery terminal.

4. The backup pump leads are polarity sensitive. Connect

the positive pump lead to the terminal labeled Pump ‘+’ and

the negative pump lead to the terminal labeled Pump ‘–’.

NOTE: If the leads are reversed, the pump will run

backward and not pump water.

5. The float switch leads are not polarity sensitive. Connect

the float switch leads to the Float Switch tabs on the

charger/controller.

6. Test the float and the pump by lifting and holding the float.

 The system alert LED will blink while the float is up.

 The Pump Status LED will light continuously and the

buzzer will beep steadily.

 The pump should start after 3 seconds.

 If the pump does not run, check all the connections

and remake them as necessary.

7. To stop the pump, lower the float. After 25 seconds the

pump should stop, the Pump Status LED should flash, and

the buzzer should beep.

8. With the pump operating, test the ‘SILENCE ALARM’

button:

 Hold for one second; release.

 The Alarm Silenced LED should illuminate and the

buzzer should stop sounding.

 To reset the buzzer (allow it to sound) and extinguish

the Alarm Silenced LED, press the ‘Silence Alarm’

button again for one second.

 Depress the Test System button. Hold it for one

second and then release. The Pump Status LED

should stop flashing.

WIRING AND SETUP

Figure 4: Wiring and Setup

HYD979 (06-08-20)

WIRING AND SETUP

During normal operation, the flashing Pump Status LED

indicates that the pump has run in your absence.

 Press and hold Test System button. All LEDs will light up,

pump will run and buzzer will sound.

 Release the button and LEDs should go off, pump should

stop, buzzer should stop.

 The Battery Status LED indicates the battery capacity

when the A.C. power is off.

1. Continuously ON - the battery voltage is above 10.9 Volts

Direct Current (10.9VDC) and capacity is above 20%.

2. Slow Beep/Slow LED Flash - the battery’s capacity is

between 0 and 20%.

3. Fast Beep/Fast LED Flash - the battery is severely

discharged. The battery will continue to charge (as long

as the 115V AC power to the charger is on) at the rate of

.5 AH until the battery’s charge is above 20%.

When the first warning occurs (slow beep/slow flash),

you will have approximately 2 hours (or less) of pump

operation left. The actual time of operation will depend

on the condition of the battery and may be as little as 15

minutes.

 Connect the Power Supply cable (supplied) to the Charger/

Controller’s Power Input jack.

 When the unit is first plugged in, or when it first receives power from the battery, the Battery Status LED will flash for 3

seconds.

 To activate any Control Button, press and hold it for 1 second.

Figure 5: LED Display and Control Buttons

HYD979 (06-08-20)

CHARGER/CONTROLLER LED DISPLAY

LED Operating Code Display System Operating Condition

CHARGING

BATTERY STATUS

PUMP ACTIVITY

AC POWER

ALARM SILENCED

SYSTEM ALERT

Indicates 115V AC Power is connected / Unit online

NOTICE: All of the situations listed above indicate normal system operation; no action is required.

However, if the BBU pump is running or has run, check the primary pump and actively monitor the

charger status for battery life. Always reset the charger after the pump runs.

During normal system operation, the ‘SYSTEM ALERT’ LED blinks while the float switch is on,

indicating the pump should start within 3 seconds. The “AC POWER” LED is lighted

(solid or blinking) as long as the system is plugged in to an operating AC power circuit.

Indicates Pump is running (continuous LED)

Indicates Audible alarm is switched off

Indicates Battery is charging normally

Indicates Continuous LED: battery charge is above 20%,

system is maintaining charge

Indicates Slow flashing LED: battery charge is below 20%

6790 0313

LED is Flashing (Slow)

=LED is OFF

LED is ON Continuously

= =

LED is Flashing (Fast)

Indicates Fast flashing LED: Pump has run

Indicates Fast flashing LED: Battery pre-qualification test is running

Indicates 115V AC Power is connected / Unit offline

 When the System Alert light IS NOT flashing, refer to Figure 6.

 When the System Alert light IS flashing, refer to Figure 7 .

 All of the situations listed above indicate normal system operation; no action is required. However, if the BBU pump is running or

has run, check the primary pump and actively monitor the charger status for battery life. Always reset the charger after the pump

runs.

 During normal system operation, the SYSTEM ALERT LED blinks while the float switch is on,indicating the pump should start

within 3 seconds. The “AC POWER” LED is lighted (solid or blinking) as long as the system is plugged in to an operating AC power

circuit.

CONTROL LED CONTINUOUS ILLUMINATION INDICATES NORMAL OPERATION

AC Power AC power is present. Unit is online.

Pump Status The oat switch has been activated. The LED remains on (ashing) after the pump has stopped.

Depress the ‘System Test’ button to reset it.

Silenced Audible Alarm Audible Alarm has been silenced. Press and release the ‘Silence Alarm’ button to reset (activate) the

audible alarm and turn OFF the LED.

Charging Indicates that the battery is charging – see Table II, above.

Battery Status Continuous ON - the battery voltage is above 10.9 Volts DC and capacity is above 20%.

Slow Beep/Slow LED Flash - the battery’s capacity is below 20%, and voltage is between 8.2VDC and

10.9VDC.

Fast Beep/Fast LED Flash - the battery has been discharged to less than 8.2VDC.

System Alert Flashing (in unison with the buzzer) indicates that the charger has entered ‘Failure Mode’. Press the

System Test and Silence Alarm buttons to reset it. If the source of the failure is not corrected, the

charger will reenter Failure Mode. See Table IV for error code information.

Figure 6: Operating Code Displays

(LEDs Lighted Continuously or Flashing)

Table II: LED Function Displays (LEDs Lighteded Continuously)

HYD979 (06-08-20)

CHARGER/CONTROLLER LED DISPLAY

CONTROL BUTTON: RESULT OF PUSHING BUTTON:

System Test Pump starts and all LEDs light up.

Will reset the pump Activity LED.

When pushed with the Silence Alarm button, the Charger/Controller microprocessor resets and error code resets.

Silence Alarm Toggle; Prevents the audible alarm sounding. Press and release to reset.

Light Toggles the light on the Charger/Controller on and off.

System Reset Press and release Test System and Silence Alarm to reset system.

Figure 7: Error Code Displays (LEDs Flashing)

 When the System Alert light IS NOT flashing, refer to Figure 6.

 When the System Alert light IS flashing, refer to Figure 7 .

Table II: Control Button Functions

HYD979 (06-08-20)

TROUBLESHOOTING

TROUBLESHOOTING - PUMP

Pump won’t run. Check all the wiring connections.

Check for a low or defective battery.

Check that the automatic switch is free to move up and down.

Press the circuit breaker reset button on the control panel.

Motor hums but pump won’t run. Check for low or defective battery.

Pump runs but pumps very little or no

water.

Make sure a check valve is installed and functioning between the primary pump discharge and the

Battery Backup wye.

Check for an obstruction in the discharge pipe.

The discharge pipe length and/or height exceeds the capacity of the pump.

Check for a low or defective battery.

The Positive (+) and negative (–) pump wires are reversed. Disconnect them and reconnect

correctly.

Pump cycles too frequently. The check valve located between the discharge of the primary pump and the Battery Backup wye is

not installed or is not working properly. Install an auxiliary check valve or replace the existing check

valve as required.

HYD979 (06-08-20)

Key No. Part Description Part Number

1 DC Backup Pump PS17-2005*

2 1-1/4 FNPT x 1-1/2 Slip Elbow U78-1012

3 Float Switch PS17-2003

4Charger/Controller PS217-1522

5 Battery Case Base

Battery Case Cover

PS17-2044

PS17-2045

6 AC Adaptor PS17-2008

7 Cable Ties - 11” **

8 Gateway Kit (Gateway, Power Supply, 1m RJ45 Cable) U117-1568

9Switch Bracket PS17-2004

* If pump fails, replace entire system.

** Sold separately.

NOTICE: All check valves must be installed as described in the installation instructions or the warranty is

void. This includes the check valve for the primary sump pump in a Common Discharge installation.

Part Description Part Number

AGM 40A-Hour BAT40

Optional Batterry Supplies Sold Separately

PARTS LIST

HYD979 (06-08-20)

WARRANTY

Limited Warranty

Hydromatic® warrants to the original consumer purchaser (“Purchaser” or “You”) of the products listed below, that they will be free

from defects in material and workmanship for the Warranty Period shown below.

Product Warranty Period

whichever occurs first:

Submersible utility pumps and related accessories 12 months from date of original installation,

or 18 months from date of manufacture

Sump/Sewage/Effluent Products 12 months from date of original installation,

or 36 months from date of manufacture

Battery Backup Units

FG-2200, FG-2200C

FG-3100, FG-3100C

12 months from date of original installation,

or 18 months from date of manufacture

24 months from date of original installation,

or 30 months from date of manufacture

Wastewater Solids Handling Pumps 12 months from date of shipment from factory

or 18 months from date of manufacture

Our warranty applies only where such products are used in compliance with the requirements of the applicable product catalog

and/or manuals. For additional information, please refer to the applicable standard limited warranty featured in the product

manual.

Our warranty will not apply to any product that, in our sole judgement, has been subject to negligence, misapplication, improper

installation, or improper maintenance. Without limiting the foregoing, operating a three phase motor with single phase power

through a phase converter will void the warranty. Note also that three phase motors must be protected by three-leg, ambient

compensated, extra-quick trip overload relays of the recommended size or the warranty is void.

Your only remedy, and HYDROMATIC’s only duty, is that HYDROMATIC repair or replace defective products (at

HYDROMATIC’s choice).

You must pay all labor and shipping charges associated with this warranty and must request warranty service through the

installing dealer as soon as a problem is discovered.

No request for service will be accepted if received after the Warranty Period has expired. This warranty is not transferable.

HYDROMATIC SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES

WHATSOEVER.

THE FOREGOING LIMITED WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES,

INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE.

THE FOREGOING LIMITED WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on the duration of an

implied warranty, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights and You

may also have other rights which vary from state to state.

This Limited Warranty is effective February 2, 2015 and replaces all undated warranties and warranties dated after

February 2, 2015.

HYDROMATIC

293 Wright Street, Delavan, WI 53115

Phone: 888-957-8677 • Fax: 800-426-9446 • www.hydromatic.com

In Canada: 490 Pinebush Road, Unit 4, Cambridge, Ontario N1T 0A5

Phone: 800-363-7867 • Fax: 888-606-5484

pentair.com

MANUEL D’INSTALLATION

ET D’UTILISATION

Pump Activity

Activité de pompe

Actividad de la bomba

System Alert

Alerte du système

Alerta del sistema

AC Power

Courant AC

Charging

Recharge

En carga

Battery Status

État de batterie

Estado de la batería

Alarm Silenced

Alarme arrêtée

Alarma apagada

Test System

Tester

Probar sistema

Silence Alarm

Arrêter l’alarme

Apagar alarma

Light

Lumière

Luz

Circuit Breaker

Disjoncteur

Disyuntor

Pump

Pompe

Bomba

Float Switch

Interrupteur à otteur

Interruptor del otador

Power

Courant

Encendido

Reset System

Réinitialise

Restrablecer sistema

SYSTÈME DE SECOURS À BATTERIE

FG-3100RF

HYD979 (06-08-20)

TABLE DES MATIÈRES

Renseignements relatifs à la sécurité ...................................................................................................................................................................20

Renseignements généraux .................................................................................................................................................................................... 21

Conguration de la connexion Internet et des alertes ........................................................................................................................................... 22

Exigences relatives à la batterie ........................................................................................................................................................................... 27

Câblage et installation ........................................................................................................................................................................................... 28

Achage du chargeur/contrôleur .........................................................................................................................................................................30

Dépannage ............................................................................................................................................................................................................ 32

Liste des pièces..................................................................................................................................................................................................... 33

Garantie .................................................................................................................................................................................................................34

HYD979 (06-08-20)

IMPORTANTES CONSIGNES DE SÉCURITÉ

CONSERVEZ CES INSTRUCTIONS – Ce manuel comporte des

consignes importantes qui doivent être suivies lors de l’installation,

de l’utilisation et de l’entretien du produit.

Ceci est le symbole d’alerte de sécurité. Si vous voyez ce

symbole sur votre pompe ou dans ce manuel, recherchez l’un des

mots d’avertissement ci-dessous et faites attention aux risques

de blessures!

indique un danger qui, s’il n’est pas évité, entraînera

la mort ou des blessures graves.

indique un danger qui, s’il n’est pas évité,

peut entraîner la mort ou des blessures graves.

indique un danger qui, s’il n’est pas évité, peut ou

pourrait entraîner des blessures légères ou moyennement graves.

REMARQUE: concerne des pratiques non liées aux lésions

corporelles.

 Conservez les étiquettes de sécurité en bon état. Remplacez-

les si elles sont manquantes ou endommagées.

 Pour éviter tout risque de blessures graves causées par un

choc électrique ou par des brûlures, ainsi que des dommages

matériels en raison d’une inondation, lisez attentivement et

suivez toutes les instructions de sécurité figurant dans ce

manuel et sur la pompe avant d’installer la pompe.

 L’acide de batterie est corrosif. Évitez

les éclaboussures sur la peau, les vêtements ou le chargeur

de batterie. Portez un équipement de protection pour les yeux

et la tête lorsque vous manipulez la batterie. Branchez et

débranchez les bornes de sortieCC uniquement après avoir

débranché le chargeur de la prise de courantCA. Ne laissez

jamais les bornes de courant continu(CC) se toucher.

 Tension dangereuse. Peut provoquer

un choc électrique grave ou mortel. Ne branchez ou ne

débranchez pas le chargeur de batterie lorsque vous vous

trouvez sur un plancher mouillé ou dans l’eau. Assurez-vous

de garder une main libre lorsque vous branchez ou débranchez

le chargeur. Si le plancher du sous-sol est mouillé, coupez

l’alimentation électrique du sous-sol avant de marcher sur

le plancher.

 Risque d’inondation. Ne faites pas

fonctionner la pompe à sec. Cela endommage les

joints et pourrait provoquer des fuites et des

dommages matériels.

 Conformez-vous aux codes de plomberie et d’électricité

lorsque vous installez le système. Il est recommandé d’utiliser

un disjoncteur différentiel de fuite à la terre (DDFT) lors de

l’utilisation d’un appareil électrique immergé sous l’eau.

 N’utilisez ce système que comme pompe de puisard de secours

à utilisation résidentielle. Ce système n’est pas conçu pour être

utilisé comme pompe de puisard principale.

 Ne soulevez pas la pompe par le cordon électrique.

 Risque de choc électrique. Ne soulevez

pas la pompe par le cordon électrique, soulevez-la uniquement

par le tuyau d’évacuation, l’anneau de levage ou la poignée de

la pompe. Soulever la pompe par le cordon peut endommager

ce dernier.

 Utilisez cette pompe uniquement pour pomper de l’eau claire.

 La pompe est dotée d’une lubrification permanente installée

en usine. N’essayez pas de la lubrifier!

 Gardez le chargeur de batterie et le compartiment de batterie

à l’écart du plancher, dans un endroit sec, frais et bien aéré.

 REMARQUE: Si un détecteur de monoxyde de carbone(CO)

est installé, il doit se situer à au moins 15pieds du chargeur de

batterie pour éviter les fausses alarmes. Pour obtenir de plus

amples renseignements, veuillez consulter les instructions

d’installation de votre détecteur de monoxyde de carbone.

 Pour éviter les risques d’incendie ou d’explosion, gardez la

batterie loin de sources étincelles et de flammes (par exemple,

un brûleur de veilleuse).

 La distance verticale maximale de pompage est de 4,6m (15pi)

pour le modèle FPDC30.

 Assurez-vous que la pompe de puisard ne contient pas de

débris. Les débris peuvent endommager la pompe et causer

des inondations.

Avertissement concernant la proposition 65 de la Californie

Ce produit et les accessoires connexes

contiennent des produits chimiques considérés par l’État de

la Californie comme pouvant causer le cancer, des anomalies

congénitales ou d’autres troubles du système reproducteur.

CONSIGNES DE SÉCURITÉ

La page charge ...

Pentair Hydromatic FG-3100RF Battery Backup System Le manuel du propriétaire

Marque: Pentair Hydromatic

Modèle: FG-3100RF Battery Backup System

Catégorie: Pompes à eau

Taper: Le manuel du propriétaire

Ce manuel convient également à

FG-3100RF

Télécharger le PDF

rapport

Pentair Hydromatic FG-3100RF Battery Backup System Le manuel du propriétaire

Ce manuel convient également à

Pentair Hydromatic FG-3100RF Battery Backup System Le manuel du propriétaire

dans d''autres langues

Autres documents