Rockwell Automation 1766-L32AWA Installation Instructions Manual

Taper
Installation Instructions Manual

Ce manuel convient également à

Installation Instructions
MicroLogix 1400 Programmable Controllers
Catalog Number(s) 1766-L32AWA, 1766-L32AWAA,
1766-L32BWA, 1766-L32BWAA, 1766-L32BXB,
1766-L32BXBA
Topic Page
Important User Information 2
Additional Resources 5
Overview 6
Controller Description 7
Hazardous Location Considerations 9
Mount the Controller 11
Connect 1762 I/O Expansion Modules 16
Wire the Controller 17
Specifications 26
2 MicroLogix 1400 Programmable Controllers
Publication 1766-IN001D-EN-P - June 2015
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical equipment.
Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication
SGI-1.1 available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com
) describes some important differences between solid state
equipment and hard-wired electromechanical devices. Because of this difference, and also because of the
wide variety of uses for solid state equipment, all persons responsible for applying this equipment must
satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many
variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot
assume responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING
·
Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.
IMPORTANT
Identifies information that is critical for successful application and understanding of
the product.
ATTENTION
Identifies information about practices or circumstances that can lead to personal injury
or death, property damage, or economic loss. Attentions help you identify a hazard,
avoid a hazard and recognize the consequences.
SHOCK HAZARD
Labels may be on or inside the equipment (for example, drive or motor) to alert people
that dangerous voltage may be present.
BURN HAZARD
Labels may be on or inside the equipment (for example, drive or motor) to alert people
that surfaces may reach dangerous temperatures.
MicroLogix 1400 Programmable Controllers 3
Publication 1766-IN001D-EN-P - June 2015
Environment and Enclosure
Preventing Electrostatic Discharge
ATTENTION
This equipment is intended for use in a Pollution Degree 2 industrial
environment, in overvoltage Category II applications (as defined in IEC
publication 60664-1), at altitudes up to 2000 meters (6562 ft) without derating.
This equipment is considered Group 1, Class A industrial equipment according to
IEC/CISPR Publication 11. Without appropriate precautions, there may be
potential difficulties ensuring electromagnetic compatibility in other
environments due to conducted as well as radiated disturbance.
This equipment is supplied as open-type equipment. It must be mounted within
an enclosure that is suitably designed for those specific environmental
conditions that will be present and appropriately designed to prevent personal
injury resulting from accessibility to live parts. The enclosure must have suitable
flame-retardant properties to prevent or minimize the spread of flame,
complying with a flame spread rating of 5VA, V2, V1, V0 (or equivalent) if
non-metallic. The interior of the enclosure must be accessible only by the use of
a tool. Subsequent sections of this publication may contain additional
information regarding specific enclosure type ratings that are required to comply
with certain product safety certifications.
ATTENTION
This equipment is sensitive to electrostatic discharge, which can cause internal
damage and affect normal operation. Follow these guidelines when you handle
this equipment:
Touch a grounded object to discharge potential static.
Wear an approved grounding wriststrap.
Do not touch connectors or pins on component boards.
Do not touch circuit components inside the equipment.
Use a static-safe workstation, if available.
Store the equipment in appropriate static-safe packaging when not in use.
4 MicroLogix 1400 Programmable Controllers
Publication 1766-IN001D-EN-P - June 2015
North American Hazardous Location Approval
The following modules are North American Hazardous Location approved: 1766-L32AWA,
1766-L32AWAA, 1766-L32BWA, 1766-L32BWAA, 1766-L32BXB, 1766-L32BXBA
The following information applies when
operating this equipment in hazardous
locations:
Informations sur l’utilisation de cet
équipement en environnements
dangereux:
Products marked "CL I, DIV 2, GP A, B, C, D" are
suitable for use in Class I Division 2 Groups A, B, C,
D, Hazardous Locations and nonhazardous locations
only. Each product is supplied with markings on the
rating nameplate indicating the hazardous location
temperature code. When combining products within
a system, the most adverse temperature code
(lowest "T" number) may be used to help determine
the overall temperature code of the system.
Combinations of equipment in your system are
subject to investigation by the local Authority Having
Jurisdiction at the time of installation.
Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne
conviennent qu’à une utilisation en environnements
de Classe I Division 2 Groupes A, B, C, D dangereux et
non dangereux. Chaque produit est livré avec des
marquages sur sa plaque d’identification qui
indiquent le code de température pour les
environnements dangereux. Lorsque plusieurs
produits sont combinés dans un système, le code de
température le plus défavorable (code de température
le plus faible) peut être utilisé pour déterminer le code
de température global du système. Les combinaisons
d’équipements dans le système sont sujettes à
inspection par les autorités locales qualifiées au
moment de l’installation.
WARNING
EXPLOSION HAZARD
Do not disconnect while the
circuit is live or unless the area
is known to be free of ignitible
concentrations.
Do not disconnect connections
to this equipment unless power
has been removed or the area is
known to be nonhazardous.
Secure any external connections
that mate to this equipment by
using screws, sliding latches,
threaded connectors, or other
means provided with this
product.
Substitution of components may
impair suitability for Class I,
Division 2.
Do not remove or replace lamps,
fuses or plug-in modules (as
applicable) unless power has
been disconnected or the area is
known to be free of ignitible
concentrations of flammable
gases or vapors.
AVERTISSEMENT
RISQUE D’EXPLOSION
Couper le courant ou s’assurer
que l’environnement est classé
non dangereux avant de
débrancher l'équipement.
Couper le courant ou s'assurer
que l’environnement est classé
non dangereux avant de
débrancher les connecteurs. Fixer
tous les connecteurs externes
reliés à cet équipement à l'aide
de vis, loquets coulissants,
connecteurs filetés ou autres
moyens fournis avec ce produit.
La substitution de composants
peut rendre cet équipement
inadapté à une utilisation en
environnement de Classe I,
Division 2.
S’assurer que l’environnement
est classé non dangereux avant
de changer les piles.
MicroLogix 1400 Programmable Controllers 5
Publication 1766-IN001D-EN-P - June 2015
Additional Resources
If you would like a manual, you can:
download a free electronic version from the internet:
http://literature.rockwellautomation.com
purchase a printed manual by contacting your local Allen-Bradley distributor or
Rockwell Automation representative
Resource Description
MicroLogix 1400 Programmable Controllers User
Manual 1766-UM001
A more detailed description of how to install and use
your MicroLogix 1400 programmable controller and
expansion I/O system.
MicroLogix 1400 Instruction Set Reference
Manual 1766-RM001
A reference manual that contains data and function
files, instruction set, and troubleshooting information
for MicroLogix 1400.
Installation Instructions 1762-INxxx Information on installing and using 1762 expansion I/O
modules.
Industrial Automation Wiring and Grounding
Guidelines 1770-4.1
More information on proper wiring and grounding
techniques.
6 MicroLogix 1400 Programmable Controllers
Publication 1766-IN001D-EN-P - June 2015
Overview
MicroLogix 1400 controllers are suitable for use in an industrial environment when installed
in accordance with these instructions. Specifically, this equipment is intended for use in clean,
dry environments (Pollution degree 2
(1)
) and with circuits not exceeding Over Voltage
Category II
(2)
(IEC 60664-1)
(3)
. AC powered products must be connected to the secondary of
an isolating transformer.
Install your controller using these installation instructions.
(1)
Pollution Degree 2 is an environment where, normally, only non-conductive pollution occurs except that occasionally a
temporary conductivity caused by condensation shall be expected.
(2)
Over Voltage Category II is the load level section of the electrical distribution system. At this level transient voltages are
controlled and do not exceed the impulse voltage capability of the product's insulation.
(3)
Pollution Degree 2 and Over Voltage Category II are International Electrotechnical commissions (IEC) designations.
ATTENTION
Do not remove the protective debris strip until after the controller and all other
equipment in the panel near the controller are mounted and wiring is complete.
Once wiring is complete, remove protective debris strip. Failure to remove strip
before operating can cause overheating.
ATTENTION
Electrostatic discharge can damage semiconductor devices inside the controller.
Do not touch the connector pins or other sensitive areas.
Debris strip
44513
MicroLogix 1400 Programmable Controllers 7
Publication 1766-IN001D-EN-P - June 2015
Controller Description
Description
1 Comm port 2 - 9-pin D-Shell RS-232C connector
2 Memory module (refer to MicroLogix 1400 Memory Module Installation Instructions, publication
1766-IN010
for instructions on installing the memory module).
3 User 24V (for 1766-L32BWA and 1766-L32BWAA only)
4 Input terminal block
5 LCD Display Keypad (ESC, OK, Up, Down, Left, Right)
6 Battery compartment
7 1762 expansion bus connector
8 Battery connector
9 Output terminal block
10 LCD Display
11 Indicator LED panel
12 Comm port 1 - RJ45 connector
13 Comm port 0 - 8-pin mini DIN RS-232C/RS-485 connector
1
ESC
OK
256 7
8
9101113 12
43
1
44515
44514
Left side view Top view
8 MicroLogix 1400 Programmable Controllers
Publication 1766-IN001D-EN-P - June 2015
Controller Input and Output Description
Catalog
Number
Description
Input
Power
User
Power
Embedded
Discrete I/O
Embedded
Analog I/O
Comm.
Ports
1766-L32BWA
100/240V AC
24V DC
12 Fast 24V DC Inputs
8 Normal 24V DC Inputs
12 Relay Outputs
None
1 RS232/RS485
(1)
1 Ethernet/IP
1 RS232
(2)
1766-L32AWA
None
20 120V AC Inputs
12 Relay Outputs
1766-L32BXB 24 V DC
12 Fast 24V DC Inputs
8 Normal 24V DC Inputs
6 Relay Outputs
3 Fast DC Outputs
3 Normal DC Outputs
1766-L32BWAA
100/240V AC
24V DC
12 Fast 24V DC Inputs
8 Normal 24V DC Inputs
12 Relay Outputs
4 Voltage Inputs
2 Voltage
Outputs
1766-L32AWAA
None
20 120V AC Inputs
12 Relay Outputs
1766-L32BXBA 24V DC
12 Fast 24V DC Inputs
8 Normal 24V DC Inputs
6 Relay Outputs
3 Fast DC Outputs
3 Normal DC Outputs
(1)
Isolated RS-232/RS-485 combo port. Same as ML1100 Comm 0
(2)
Non-isolated RS-232. Standard D-sub connector
MicroLogix 1400 Programmable Controllers 9
Publication 1766-IN001D-EN-P - June 2015
Hazardous Location Considerations
This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous
locations only. The following WARNING statement applies to use in hazardous locations.
Use only the following communication cables in Class I, Division 2 hazardous locations.
WARNING
·
EXPLOSION HAZARD
Substitution of components may impair suitability for Class I, Division 2.
Do not replace components or disconnect equipment unless power has been switched
off.
Do not connect or disconnect components unless power has been switched off.
This product must be installed in an enclosure. All cables connected to the product
must remain in the enclosure or be protected by conduit or other means.
All wiring must comply with N.E.C. article 501-10(b) and/or in accordance with
Section 18-1J2 of the Canadian Electrical Code, and in accordance with the authority
having jurisdiction.
For applicable equipment (for example, relay modules), exposure to some chemicals
may degrade the sealing properties of the materials used in these devices:
Relays, epoxy
It is recommended that you periodically inspect these devices for any degradation of
properties and replace the module if degradation is found.
Environment Classification Communication Cables
Class I, Division 2 Hazardous Environment 1761-CBL-AC00 Series C or later
1761-CBL-AM00 Series C or later
1761-CBL-AP00 Series C or later
1761-CBL-PM02 Series C or later
1761-CBL-HM02 Series C or later
2707-NC9 Series C or later
1763-NC01 Series A or later
1747-CP3 Series
10 MicroLogix 1400 Programmable Controllers
Publication 1766-IN001D-EN-P - June 2015
Environnements dangereux
Cet équipement est conçu pour une utilisation en environnements dangereux de Classe I,
Division 2, Groupes A, B, C, D ou non dangereux. La mise en garde suivante s’applique à
utilisation en environnements dangereux.
Utilisez uniquement les câbles de communication suivants dans les environnements
dangereux de Classe I, Division 2.
WARNING
·
DANGER D’EXPLOSION
La substitution de composants peut rendre cet équipement impropre à une utilisation
en environnement de Classe I, Division 2.
Ne pas remplacer de composants ou déconnecter l’équipement sans s’être assuré que
l’alimentation est coupée.
Ne pas connecter ou déconnecter des composants sans s’être assuré que
l’alimentation est coupée.
Ce produit doit être installé dans une armoire. Tous les câbles connectés à l’appareil
doivent rester dans l’armoire ou être protégés par une goulotte ou tout autre moyen.
L’ensemble du câblage doit être conforme à la réglementation en vigueur dans les
pays où l’appareil est installé.
Classification des environnements Câbles de communication
Environnement dangereux de Classe I, Division 2 1761-CBL-AC00 série C ou ultérieure
1761-CBL-AM00 série C ou ultérieure
1761-CBL-AP00 série C ou ultérieure
1761-CBL-PM02 série C ou ultérieure
1761-CBL-HM02 série C ou ultérieure
2707-NC9 série C ou ultérieure
1763-NC01 série A ou ultérieure
série 1747-CP3
UNSUPPORTED CONNECTION
Do not connect the Comm0 port on the MicroLogix 1400 controller to another MicroLogix
family controller such as MicroLogix 1000, MicroLogix 1200, or MicroLogix 1500 using a
1761-CBL-AM00 (8-pin mini-DIN to 8-pin mini-DIN) cable or equivalent.
This type of connection will cause damage to the RS-232/485 communication port
(Channel 0) of the MicroLogix 1400 and/or the controller itself. Communication pins used
for RS-485 communications are alternately used for 24V power on the other MicroLogix
controllers.
MicroLogix 1400 Programmable Controllers 11
Publication 1766-IN001D-EN-P - June 2015
Mount the Controller
General Considerations
Most applications require installation in an industrial enclosure to reduce the effects of
electrical interference and environmental exposure. Locate your controller as far as possible
from power lines, load lines, and other sources of electrical noise such as hard-contact
switches, relays, and ac motor drives. For more information on proper grounding guidelines,
see the Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1
.
ATTENTION
Mount the controller horizontally only. Vertical mounting is not supported due to
thermal considerations.
ATTENTION
Be careful of metal chips when drilling mounting holes for your controller or
other equipment within the enclosure or panel. Drilled fragments that fall into
the controller could cause damage. Do not drill holes above a mounted controller
if the protective debris strips have been removed.
WARNING
·
Do not place the MicroLogix 1400 Programmable Controller in direct sunlight.
Prolonged exposure to direct sunlight could degrade the LCD display.
WARNING
·
The local programming terminal port is intended for temporary use only and
must not be connected or disconnected unless the area is assured to be
nonhazardous.
12 MicroLogix 1400 Programmable Controllers
Publication 1766-IN001D-EN-P - June 2015
Mounting Dimensions
Controller Spacing
The controller mounts horizontally, with the expansion I/O extending to the right of the
controller. Allow 50 mm (2 in.) of space on all but the right side for adequate ventilation, as
shown below.
Dimension Height
A 90 mm (3.5 in.)
B 180 mm (7.087 in.)
C 87 mm (3.43 in.)
C
B
A
1766-L32BWA, 1766-L32AWA, 1766-L32BXB,
1766-L32BWAA, 1766-L32AWAA, 1766-L32BXBA
44516
ESC
OK
Top
Bottom
Side
44517
MicroLogix 1400 Programmable Controllers 13
Publication 1766-IN001D-EN-P - June 2015
DIN Rail Mounting
The maximum extension of the latch is 14 mm (0.55 in.) in the open position. A flat-blade
screwdriver is required for removal of the controller. The controller can be mounted to
EN50022-35x7.5 or EN50022-35x15 DIN rails. DIN rail mounting dimensions are shown
below.
Follow these steps to install your controller on the DIN rail.
1. Mount your DIN rail. Make sure that the placement of the controller on the DIN rail
meets the recommended spacing requirements (see Controller Spacing on page 12 for
more information). Refer to the mounting template inside the back cover of this
document.
2. If it is open, close the DIN latch.
3. Hook the top slot over the DIN rail.
4. While pressing the controller down against the top of the rail, snap the bottom of the
controller into position.
5. Leave the protective debris strip attached until you are finished wiring the controller
and any other devices.
Dimension Height
A 90 mm (3.5 in.)
B 27.5 mm (1.08 in.)
C 27.5 mm (1.08 in.)
A
B
C
44518
14 MicroLogix 1400 Programmable Controllers
Publication 1766-IN001D-EN-P - June 2015
Follow these steps to remove your controller from the DIN rail.
1. Place a flat-blade screwdriver in the DIN rail latch at the bottom of the controller.
2. Holding the controller, pry downward on the latch until the latch locks in the open
position.
3. Repeat steps 1 and 2 for the second DIN rail latch.
4. Unhook the top of the DIN rail slot from the rail.
Panel Mounting
Mount to panel using #8 or M4 screws. Follow these steps to install your controller using
mounting screws.
1. Remove the mounting template from inside the back cover of this document.
2. Secure the template to the mounting surface. Make sure your controller is spaced
properly (see Controller Spacing on page 12 for more information).
3. Drill holes through the template.
4. Remove the mounting template.
5. Mount the controller.
6. Leave the protective debris strip
in place until you are finished
wiring the controller and any
other devices
ESC
OK
Open Closed
44519
44520
ESC
OK
Mounting Template
44521
MicroLogix 1400 Programmable Controllers 15
Publication 1766-IN001D-EN-P - June 2015
Using the Battery
The MicroLogix 1400 controller is equipped with a replaceable battery (catalog number
1747-BA). The Battery Low indicator on the LCD display of the controller shows the status
of the replaceable battery. When the battery is low, the indicator is set (displayed as a solid
rectangle). This means that either the battery wire connector is disconnected, or the battery
may fail within 2 days if it is connected.
Follow these steps to connect the replaceable battery.
1. Insert the replaceable battery wire connector into the controller’s battery connector.
IMPORTANT
The MicroLogix 1400 controller ships with the battery wire connector connected.
Ensure that the battery wire connector is inserted into the connector port if your
application needs battery power. For example, when using a real-time clock
(RTC).
Replacing the battery when the controller is powered down will lose all user
application memory. Replace the battery when the controller is powered on.
Refer to the SLC 500 Lithium Battery Installation Instructions, publication
1747-IN515
, for more information on installation, handling, usage, storage, and
disposal of the battery.
WARNING
·
When you connect or disconnect the battery an electrical arc can occur. This
could cause an explosion in hazardous location installations. Be sure that the
area is nonhazardous before proceeding.
For Safety information on the handling of lithium batteries, including handling
and disposal of leaking batteries, see Guidelines for Handling Lithium Batteries,
publication AG 5-4
.
16 MicroLogix 1400 Programmable Controllers
Publication 1766-IN001D-EN-P - June 2015
2. Secure the battery connector wires so that it does not block the 1762 expansion bus
connector as shown below.
Connect 1762 I/O Expansion Modules
Connect 1762 I/O after mounting the controller.
1. Remove the expansion port cover to install expansion I/O modules.
2. Plug the ribbon cable connector into the bus connector.
ATTENTION
Remove power from the system before installing or removing expansion I/O or damage to
the controller may result.
1762 I/O
expansion bus
connector
Battery wires
twisted pair
Battery
Battery wire
connector
Battery connector
44522
Battery compartment
MicroLogix 1400 Programmable Controllers 17
Publication 1766-IN001D-EN-P - June 2015
3. Replace the cover as shown below.
The MicroLogix 1400 controller is designed to support up to any seven 1762 expansion I/O
modules.
For detailed information on using expansion I/O, refer to the installation instructions for
your expansion module.
Wire the Controller
The shading in the following terminal block illustrations indicates which terminal groups are
tied to which commons.
Terminal Block Layouts
WARNING
·
When you connect or disconnect the Removable Terminal Block (RTB) with field
side power applied, an electrical arc can occur. This could cause an explosion in
hazardous location installations. Be sure that power is removed or the area is
nonhazardous before proceeding.
WARNING
·
When used in a Class I, Division 2, hazardous location, this equipment must be
mounted in a suitable enclosure. All wiring must be in accordance with Class I,
Division 2 wiring methods of Article 501 of the National Electrical Code and/or
in accordance with Section 18-1J2 of the Canadian Electrical Code, and in
accordance with the authority having jurisdiction.
44523
18 MicroLogix 1400 Programmable Controllers
Publication 1766-IN001D-EN-P - June 2015
1766-L32BWA/L32BWAA
1766-L32AWA/L32AWAA
IN1
IN0 IN2
IN3
COM 0
IV0(+) IV2(+)
COM 1
IV1(+) IV3(+)
IN5 IN7
IN4 IN6
COM 2
IN8 IN10
IN9 IN11
COM 3
IN13 IN15 IN17 IN19
IN12 IN14 IN16 IN18
COM
ANA
L1
DC0
OV1
OUT0
OUT1 OUT2 OUT3 OUT4
OUT5
OUT7 OUT8 OUT10
OUT6 OUT9 OUT11
OV0
VAC
L2/N
VAC
VAC
DC1
VAC
DC2
VAC
DC3
VAC
DC4
VAC
DC6
VAC
COM
ANA
DC5
VAC
Group 0 Group 1 Group 2 Group 3 Group 5Group 4 Group 6
Input Terminal Block
Output Terminal Block
44524
IN1
IN0 IN2
IN3
COM 0
IV0(+) IV2(+)
COM 1
IV1(+) IV3(+)
IN5 IN7
IN4 IN6
COM 2
IN8 IN10
IN9 IN11
COM 3
IN13 IN15 IN17 IN19
IN12 IN14 IN16 IN18
COM
ANA
L1
DC0
OV1
OUT0
OUT1 OUT2 OUT3 OUT4
OUT5
OUT7 OUT8 OUT10
OUT6 OUT9 OUT11
OV0
VAC
L2/N
VAC
VAC
DC1
VAC
DC2
VAC
DC3
VAC
DC4
VAC
DC6
VAC
COM
ANA
DC5
VAC
Group 0 Group 1 Group 2 Group 3 Group 5Group 4 Group 6
Input Terminal Block
Output Terminal Block
44525
MicroLogix 1400 Programmable Controllers 19
Publication 1766-IN001D-EN-P - June 2015
1766-L32BXB/L32BXBA
Wire Type Wire Size
Solid wire Cu-90C (194F) 14…22 AWG
Stranded wire Cu-90C (194F) 16…22 AWG
Wiring torque = 0.791Nm (7 in-lb) rated.
Output Terminal Grouping
Outputs
Controller Output Group Description Voltage Terminal Output Terminal
1766-L32BWA
1766--L32BWAA
Group 0 Isolated relay output VAC/DC0 OUT 0
Group 1 Isolated relay output VAC/DC1 OUT 1
Group 2 Isolated relay output VAC/DC2 OUT 2
Group 3 Isolated relay output VAC/DC3 OUT 3
Group 4 Isolated relay output VAC/DC4 OUT 4, OUT 5
Group 5 Isolated relay output VAC/DC5 OUT 6, OUT 7
Group 6 Isolated relay output VAC/DC6 OUT 8…11
IN1
IN0 IN2
IN3
COM 0
IV0(+) IV2(+)
COM 1
IV1(+) IV3(+)
IN5 IN7
IN4 IN6
COM 2
IN8 IN10
IN9 IN11
COM 3
IN13 IN15 IN17 IN19
IN12 IN14 IN16 IN18
COM
ANA
+24
DC0
OV1
OUT0
OUT1 OUT2 OUT4 OUT6
OUT7
OUT8 OUT9 OUT10
OUT11
OV0
VDC
NEUT
VDC
VAC
DC1
VAC
VDC2 OUT3 OUT5 DC4
VAC
COM
ANA
COM 2
DC3
VAC
DC5
VAC
Group 0 Group 1 Group 3 Group 4 Group 5Group 2
Input Terminal Block
44526
20 MicroLogix 1400 Programmable Controllers
Publication 1766-IN001D-EN-P - June 2015
1766-L32AWA
1766-L32AWAA
Group 0 Isolated relay output VAC/DC0 OUT 0
Group 1 Isolated relay output VAC/DC1 OUT 1
Group 2 Isolated relay output VAC/DC2 OUT 2
Group 3 Isolated relay output VAC/DC3 OUT 3
Group 4 Isolated relay output VAC/DC4 OUT 4, OUT 5
Group 5 Isolated relay output VAC/DC5 OUT 6, OUT 7
Group 6 Isolated relay output VAC/DC6 OUT 8…11
1766-L32BXB
1766-L32BXBA
Group 0 Isolated relay output VAC/DC0 OUT 0
Group 1 Isolated relay output VAC/DC1 OUT 1
Group 2 FET output VDC2/COM 2 OUT 2…7
Group 3 Isolated relay output VAC/DC3 OUT 8
Group 4 Isolated relay output VAC/DC4 OUT 9
Group 5 Isolated relay output VAC/DC5 OUT 10, OUT 11
WARNING
·
If you connect or disconnect wiring while the field-side power is on, an electrical
arc can occur. This could cause an explosion in hazardous location installations.
Be sure that power is removed or the area is nonhazardous before proceeding
WARNING
·
The local programming terminal port is intended for temporary use only and
must not be connected or disconnected unless the area is free of ignitable
concentrations of flammable gases or vapors.
Output Terminal Grouping
Outputs
Controller Output Group Description Voltage Terminal Output Terminal
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Rockwell Automation 1766-L32AWA Installation Instructions Manual

Taper
Installation Instructions Manual
Ce manuel convient également à

dans d''autres langues