Sauder Shoal Creek 418658 Mode d'emploi

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.

Prefer the phone? Call 1-800-523-3987.

Share your journey!

sauder.com

Congratulations. You

are now an adult.

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

Enlish p 1-25

Français p 26-29

Español p 30-32

Lot # 397205 10/11/16

Purchased: __________________

Be sure to ive us a rin before

makin any returns. 1-800-523-3987

Lateral File

Shoal Creek Collection | Model 418658

Table of Contents Assembly Tools Required

Part Identiﬁ cation

Hardware Identiﬁ cation

Assembly Steps

Français

Español

Safety

Warranty

Hammer

Not actual size

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Skip the power trip.

This time.

3

4

5-25

26-29

30-32

33-34

35

418658 www.sauder.com/servicesPae 2

Part Identiﬁ cation

å While not all parts are labeled, some of the parts will have a label or an inked letter on the ede

to help distinuish similar parts from each other. Use this part identiﬁ cation to help identify similar parts.

Now you know

our ABCs.

A RIGHT END (1)

B LEFT END (1)

C2 TOP (1)

D BOTTOM (1)

D61 DRAWER BACK (1)

D87 RIGHT DRAWER SIDE (1)

D88 LEFT DRAWER SIDE (1)

D729 DRAWER BOTTOM (1)

E SHELF (1)

F BACK (1)

G DOOR (2)

H RIGHT FRONT/LEFT REAR LEG (2)

I LEFT FRONT/RIGHT REAR LEG (2)

J DRAWER FRONT (1)

K DRAWER BOX FRONT (1)

M63 DRAWER BRACE (1)

X END MOLDING (2)

A

B

C2

D

E

F

G

H

I

J

K

X

M63

D87

D88

D61

D729

418658www.sauder.com/services

Pae 3

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

(EXTENSION SET SHOWN SEPARATED)

EXTENSION RAIL - 2

L

EXTENSION SLIDE - 2

M

FILE ROD - 2

9B

FILE BAR - 2

1B

FILE GLIDE - 2

6B

BLACK 1-1/8" PAN HEAD SCREW - 4

9S

SILVER 3/4" MACHINE SCREW - 4

20S

SILVER 1-1/4" MACHINE SCREW - 4

35S

BROWN 7/16" LARGE HEAD SCREW - 4

6S3S

GOLD 5/16" FLAT HEAD SCREW - 8

SILVER 5/8" FLAT HEAD SCREW - 8

23S

PULL - 4

7K

10A

SLIDE CAM - 2

22H

HINGE SPACER - 4

BLACK 9/16" FLAT HEAD SCREW - 6

32S

CAM SCREW - 13

8F

HIDDEN CAM - 31

1F

CAM DOWEL - 18

2F

30S

BLACK 1-9/16" FLAT HEAD SCREW - 5

14H

HINGE - 4

FRONT FILE

BRACKET - 1

11B

29M

BUMPER CARD - 1

FILE BRACKET - 1

12B

418658 www.sauder.com/servicesPae 4

Step 1

Look for this icon. It means a

video assembly tip is available at

www.sauder.com/services/tips

å

Assemble your unit on a carpeted ﬂ oor or on the empty

carton to avoid scratchin your unit or the ﬂ oor.

å

Push thirty-one HIDDEN CAMS (1F) into the ENDS (A and B),

BOTTOM (D), SHELF (E), BACK (F), and DRAWER

BRACE (M63). Then, insert eihteen CAM DOWELS (2F)

into the HIDDEN CAMS except the lon edes of the

ENDS (A and B) and DRAWER BRACE (M63).

A

B

D

E

F

M63

Arrow

1F

2F

1F

2F

Arrow

(31 used)

(15 used)

Arrow

1F

2F

Do not tihten the HIDDEN CAMS in this step.

Do not insert CAM DOWELS into these edes.

Insert the metal end of the CAM

DOWEL into the HIDDEN CAM.

Arrow

Do not insert a

CAM DOWEL

into this ede.

418658www.sauder.com/services

Pae 5

å

Turn thirteen CAM SCREWS (8F) into the LEGS (H and I)

and DRAWER BOX FRONT (K).

Step 2

8F

(13 used)

H

I

K

418658 www.sauder.com/servicesPae 6

å

Fasten one of the LEGS (H and I) to the ENDS (A and B).

Tihten six HIDDEN CAMS.

Step 3

Anled ede

A

B

H

I

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

12

Just think. The sooner

you do this, the sooner

you do somethin else.

418658www.sauder.com/services

Pae 7

Ede with CAM DOWELS

å

Flip the ENDS (A and B) over. Turn six BLACK 9/16" FLAT HEAD

SCREWS (32S) into the ENDS (A and B) until the shoulders of

the SCREWS rest on the surfaces of the ENDS.

å

NOTE: Do not overtihten the SCREWS.

å

Now, slide the END MOLDINGS (P) onto the ENDS (A and B). To

do this, line up the rooves in the MOLDINGS over the heads of

the SCREWS in the ENDS. Usin your hands, apply pressure on

the MOLDINGS as you uide the MOLDINGS onto the ENDS.

å

NOTE: If the MOLDINGS come up o of the SCREWS, remove

them and slide them on aain.

Step 4

These edes

should be even.

These edes

should be even.

Shoulder

Apply pressure with your hands

as you uide the MOLDINGS over

the SCREWS and onto the ENDS.

BLACK 9/16" FLAT HEAD SCREW

(6 used in this step)

32S

A

B

P

418658 www.sauder.com/servicesPae 8

å

Flip the ENDS (A and B) over. Fasten the remainin LEGS (H

and I) to the ENDS (A and B). Tihten six HIDDEN CAMS.

Step 5

A

B

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

H

I

Anled ede

418658www.sauder.com/services

Pae 9

å

Separate the EXTENSION SLIDES (M) from the

EXTENSION RAILS (L) as shown in the upper diaram. Be

prepared, the parts are reasy.

å

Fasten the EXTENSION RAILS (L) to the ENDS (A and B).

Use four GOLD 5/16" FLAT HEAD SCREWS (3S).

å

NOTE: For each EXTENSION RAIL, turn a SCREW into the

hole shown in the enlared diaram.Then, slide the inner

cartride of the EXTENSION RAIL out to ﬁ nd the other

hole that lines up with the hole in the END. Turn a SCREW

into this hole.

Step 6

Open end

GOLD 5/16" FLAT HEAD SCREW

(4 used in this step)

3S

Push the black lever in and pull the SLIDE from the RAIL.

Hole

L

M

418658 www.sauder.com/servicesPae 10

A

B

å

Fasten the SHELF (E) to the BACK (F). Tihten two

HIDDEN CAMS.

Step 7

Ede with CAM DOWELS

Finished ede

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

E

F

Start Tighten

Arrow

Minimum

190 derees

Caution

Risk of damae or

injury. HIDDEN CAMS

must be completely

tihtened. HIDDEN

CAMS that are not

completely tihtened

may loosen, and parts

may separate. To

completely tihten:

Arrow

Maximum

210 derees

418658www.sauder.com/services

Pae 11

å

Fasten the BOTTOM (D) to the BACK (F). Tihten two

HIDDEN CAMS.

Step 8

Finished ede

Surface with

HIDDEN CAMS

F

Arrow

Minimum

190 derees

Maximum

210 derees

D

418658 www.sauder.com/servicesPae 12

å

Fasten the ENDS (A and B) to the BOTTOM (D) and

SHELF (E). Tihten eiht HIDDEN CAMS.

Step 9

Arrow

Minimum

190 derees

Maximum

210 derees

A

B

D

E

Surface with

HIDDEN CAMS

418658www.sauder.com/services

Pae 13

Surface without HIDDEN CAMS

å

Carefully stand your unit upriht.

å

Fasten the TOP (C2) to the ENDS (A and B) and BACK (F).

Tihten six HIDDEN CAMS.

Step 10

Arrow

Minimum

190 derees

Maximum

210 derees

A

B

C2

F

418658 www.sauder.com/servicesPae 14

Meet Part (C2). This component has

been enineered to be lihter, stroner,

faster… well ok. Not technically faster.

But deﬁ nitely makes for a sturdier

Lateral File that’s easier to assemble

and friendlier to the environment.

å

Fasten four HINGES (14H) and four HINGE SPACERS (22H)

to the DOORS (G). Use eiht SILVER 5/8" FLAT

HEAD SCREWS (23S).

Step 11

G

14H

22H

SILVER 5/8" FLAT HEAD SCREW

(8 used for the HINGES)

23S

Don't worry. It isn't

Rome. This can be built

in a day.

418658www.sauder.com/services

Pae 15

å

Fasten one of the DOORS (G) to the LEFT END (B). Use

the screws in the HINGES.

å

NOTE: You may need to loosen the mountin screw to

slide the HINGE slihtly out of the slot. Retihten the

screw before mountin the HINGE to the END.

å

Peel the BUMPER from the BUMPER CARD (29M). Stick

a BUMPER on the DOOR where it comes in contact with

the SHELF (E).

å

Fasten a PULL (7K) to the DOOR (G). Use two SILVER

3/4" MACHINE SCREWS (20S).

å

Repeat this step for the other DOOR (G).

Step 12

29M

SILVER 3/4" MACHINE SCREW

(4 used in this step)

20S

7K

(2 used)

B

E

G

418658 www.sauder.com/servicesPae 16

Mountin

screw

Stop

Hine

Step 13

Adjustin screw (horizontal)

Mountin screw (depth)

(vertical adjustment)

418658www.sauder.com/services

Pae 17

å

Refer to the enlared diaram to identify the parts on the

HINGES and HINGE BRACKETS.

å

The DOORS may need some adjustments. Follow the text

below to make needed adjustments. DOOR ADJUSTMENTS:

å

To adjust the DOORS from side to side (horizontal), turn the

adjustin screw in or out.

å

To adjust the DOORS up and down (vertical), loosen both

screws that fasten the HINGE BRACKETS to the END. Move the

DOORS up or down to the desired location. Tihten the screws

after makin adjustments.

å

To adjust the DOORS in or out (depth), loosen the mountin

screw one turn and move the DOORS in or out, as needed.

Tihten the mountin screw after makin adjustments.

Step 14

å

Insert the DRAWER SIDES (D87 and D88) at an angle

into the slot at each end of the DRAWER BOX FRONT (K).

å

Slide the DRAWER BOTTOM (D729) into the grooves

in the DRAWER SIDES (D87 and D88) and DRAWER

BOX FRONT (K).

å

Fasten the DRAWER BRACE (M63) to the DRAWER

BOX FRONT (K). Tighten one HIDDEN CAM.

å

Fasten the DRAWER BACK (D61) to the DRAWER

SIDES (D87 and D88) and DRAWER BRACE (M63). Use

five BLACK 1-9/16" FLAT HEAD SCREWS (30S).

The tabs should insert freely into the

slots. Gently tilt the DRAWER SIDES side

to side until the tabs slip into the slots.

Surface with

HIDDEN CAM

12

3

4

Be sure the DRAWER

BOTTOM inserts into the

DRAWER FRONT roove.

With the palm of your hand, tap the

DRAWER BOTTOM down into the roove.

Groove

Arrow

Maximum

210 derees

Minimum

190 derees

K

D87

D88

D61

VIEW THE T-LOCK BOX VIDEO

D729

Be sure the

DRAWER

BOTTOM

inserts into

the DRAWER

BACK roove.

30S

Start each screw a few turns before

completely tihtenin any of them.

BLACK 1-9/16" FLAT HEAD SCREW

(5 used in this step)

M63

K

418658 www.sauder.com/servicesPae 18

å

Fasten the DRAWER FRONT (J) to the DRAWER BOX FRONT (K).

Use four BLACK 1-1/8" PAN HEAD SCREWS (9S).

Step 15

K

BLACK 1-1/8" PAN HEAD SCREW

(4 used in this step)

9S

J

418658www.sauder.com/services

Pae 19

å

Insert the SLIDE CAMS (10A) into the lare holes in the

DRAWER SIDES (D87 and D88).

å

Fasten the EXTENSION SLIDES (M) to the DRAWER

SIDES (D87 and D88). Use four GOLD 5/16" FLAT HEAD

SCREWS (3S) throuh holes #1 and #4.

å

NOTE: The screw head in the CAM must be visible

throuh the slotted hole in the SLIDE.

Step 16

M

D87

D88

Open end

Screw head - turn CAM to line up holes in

the SLIDES with holes in DRAWER SIDES

GOLD 5/16" FLAT HEAD SCREW

(4 used in this step)

3S

1

2

3

4

10A

418658 www.sauder.com/servicesPae 20

La page charge ...

Sauder Shoal Creek 418658 Mode d'emploi

Sauder Shoal Creek 418658 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents