Pride Backpacker Plus Le manuel du propriétaire

Marque: Pride

Modèle: Backpacker Plus

Taper: Le manuel du propriétaire

Ce manuel convient également à

Backpacker AVP 2.0

MOBILITY MADE EASY. LA MOBILITE RENDUE FACILE.

Backpacker Series

Backpacker Serie

Owner’s Manual • Manuel de l’utilisateur

Including Models

Incluant les modèles

Backpacker Plus

Backpacker AVP 2.0

Available only on:

Backpacker AVP 2.0

Disponible avec:

Backpacker AVP 2.0

RF Wireless Pendant

Pendentif Sans Fil RF

WARNING! An authorized Pride Provider or a qualiﬁed technician must perform the initial setup of

this product and must perform all of the procedures in this manual.

The symbols below are used throughout this owner’s manual and on the product to identify warnings and

important information. It is very important for you to read them and understand them completely.

WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated

procedures can cause either personal injury, component damage, or malfunction. On the product,

this icon is represented as a black symbol on a yellow triangle with a black border.

MANDATORY! These actions should be performed as speciﬁed. Failure to perform mandatory actions

can cause personal injury and/or equipment damage. On the product, this icon is represented as a

white symbol on a blue dot with a white border.

PROHIBITED! These actions are prohibited. These actions should not be performed at any time or

in any circumstances. Performing a prohibited action can cause personal injury and/or equipment

damage. On the product, this icon is represented as a black symbol with a red circle and red slash.

CALIFORNIA PROPOSITION 65 WARNING! This product is equipped with batteries that contain lead

and lead components and other chemicals which are known to the state of California to cause cancer

and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Intended Use

The intended use of the Pride Mobility Products device is to aid in the transport of products that provide

mobility to persons limited to a seated position that have the capability of operating a mobility device.

NOTE: This owner’s manual is compiled from the latest speciﬁcations and product information

available at the time of publication. We reserve the right to make changes as they become

necessary. Any changes to our products may cause slight variations between the illustrations

and explanations in this manual and the product you have purchased. The latest/current version

of this manual is available on our website.

NOTE: This product is compliant with WEEE, RoHS, and REACH directives and requirements.

NOTE: This product meets IPX4 classiﬁcation (IEC 60529).

NOTE: The Backpacker Series Lift System and its components are not made with natural rubber

latex. Consult with the manufacturer regarding any after-market accessories.

Quick Reference Information

Pride Provider:

Address:

Phone Number:

Purchase Date:

INFMANU3698/Rev G/May 2018

SAFETY GUIDELINESSAFETY GUIDELINES

Backpacker Series www.pridemobility.com 3

CONTENTS

I. INTRODUCTION .......................................................................................................................................4

II. SAFETY ......................................................................................................................................................5

III. INSTALLATION .........................................................................................................................................9

IV. OPERATION ............................................................................................................................................14

V. TROUBLESHOOTING ...........................................................................................................................20

VI. CARE AND MAINTENANCE ................................................................................................................21

VII. WARRANTY .............................................................................................................................................23

4 www.pridemobility.com Backpacker Series

I. INTRODUCTION

SAFETY

Welcome to Pride Mobility Products (Pride). Congratulations on the purchase of your new lift system.

The lift system design combines the most advanced state-of-the-art components with modern, attractive

styling. We are certain that the design features and trouble-free operation will add convenience to your

daily living and ensure complete satisfaction.

At Pride, your safety is important to us. Please read and follow all instructions in this manual before

operating your lift system for the ﬁrst time. These instructions were produced for your beneﬁt. Your

understanding of these instructions is essential for the safe operation of your new lift system.

Pride is not liable for damage to property or personal injury arising out of the unsafe use of a lift

system. Pride is also not liable for any property damage or personal injury arising out of the failure of

any person and/or user to follow the instructions and recommendations set forth in this manual or any

other instructions or recommendations contained in other lift system related literature issued by Pride

or contained on the lift system itself.

INTERNET AND PRIVATE PURCHASES

If you purchased your product over the Internet or from a previous owner and you have any questions

about the safe use and/or maintenance of the product, please visit our web site www.pridemobility.com

or contact your authorized Pride Provider.

PURCHASER’S AGREEMENT

By accepting delivery of this product, you promise that you will not change, alter, or modify this product

or remove or render inoperable or unsafe any guards, shields, or other safety features of this product;

fail, refuse, or neglect to install any retroﬁt kits from time to time provided by Pride to enhance or

preserve the safe use of this product.

SHIPPING AND DELIVERY

Before using your lift system, make sure your delivery is complete as some components may be

individually packaged. If you do not receive a complete delivery, please contact your authorized Pride

Provider immediately. Where damage has occurred during transport, either to the packaging or content,

please contact the delivery company responsible.

NOTE: If you ever lose or misplace your copy of this manual, contact us and we will be glad to

send you a new one immediately.

Backpacker Series www.pridemobility.com 5

II. SAFETY

PRODUCT SAFETY SYMBOLS

The symbols below are used on the lift system to identify warnings, mandatory actions, and prohibited

actions. It is very important for you to read and understand them completely.

Crush Hazard—Moving parts can crush and cut. Keep hands clear.

Crush Hazard—Moving lift can crush. Keep feet clear during operation

Crush Hazard—Moving lift can crush. Keep hands clear during operation.

Do not sit on Power Chair or

Scooter while activating lift

or during transport.

Do not sit on mobility device while activating lift or during transport.

Keep area clean, dry, and free of obstructions.

Do not remove cover! Only authorized personnel may service this equipment. Refer to

manual for important safety information.

Read and follow the information in the owner’s manual.

Maximum lifting capacity.

Do not use as a step.

Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain

and store in a clean and dry condition.

6 www.pridemobility.com Backpacker Series

II. SAFETY

Keep tools and other metal objects away from battery terminals. Contact with tools can

cause electrical shock.

Do not allow unsupervised children to play near the lift while the battery is charging.

Corrosive chemicals contained in battery.

Explosive conditions exist!

Pinch/Crush points created during assembly and/or operation. Keep hands/ﬁngers away from

moving components during operation.

Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive conditions.

Battery posts, terminals and related accessories contain lead and lead compounds. Wear

goggles and gloves when handling batteries and wash hands after handling.

Disposal and recycling – Contact your authorized Pride Provider for information on proper

disposal of your Pride product and its packaging

Manual Override

Backpacker Series www.pridemobility.com 7

II. SAFETY

Remove transit screw and washer prior to operating the lift for the ﬁrst time.

8 www.pridemobility.com Backpacker Series

II. SAFETY

LIFTING CAPABILITIES

The Backpacker Lift System is designed for a maximum lifting capacity of 350 lbs. (159 kg). Under no

circumstances should the Backpacker Lift System be made to exceed this weight limit. Subjecting the

lift system to the strain of lifting more that it is designed to may cause it to fail, resulting in damage to

the mobility product and/or injury to the lift operator. Refer to the mobility device owner’s manual for

information on the overall weight of the mobility product before lifting.

WARNING! Exceeding the maximum lift capacity of 350 lbs. (159 kg) may cause the lift system to fail,

resulting in damage to the mobility product and/or injury to the lift operator.

WARNING! Adding accessories, oversize batteries, or a different seat will increase the weight of

your mobility product. Verify with your authorized Pride Provider the total weight of your mobility

device, including additions.

INSTALLATION

Your Backpacker Lift System is an interior lift designed for installation into various brands of SUVs and

full-sized/mini vans. Read and fully understand the installation instructions provided in this manual and

related literature for your brand of vehicle before installing the lift system.

WARNING! Before drilling or cutting into the vehicle, make absolutely certain through visual

inspection that there are no obstructions, such as the fuel tank, exhaust pipes, or electrical wires,

in the path of the drill bit.

LIFTING NON-PRIDE PRODUCTS

The Backpacker Lift System is an extremely versatile device, which users may employ to lift items other

than Pride products. Pride has no control over such use, nor can Pride anticipate every possible use

to which a Backpacker Lift System may be put. Operating the lift system outside of the safe limits as

discussed in this manual or using the lift system to lift any item deemed by Pride to be incompatible

with the lift system is done at the operator’s own risk, and Pride accepts no liability for damage or injury

resulting from such use.

PRE-LIFT INSPECTION

Before operating the Backpacker Lift System, conduct a careful survey of your surroundings to ensure

that the lift system has a clear path of operation. Remove any possible obstructions before operating

the lift and do not allow children to operate or play near the lift. Ensure that all parts of the lift system are

completely fastened before loading the mobility device onto the lift platform, and make sure the mobility

device is properly secured before operating the lift system.

OPERATOR POSITIONING

The operator of the lift should stand a safe distance from the unit being lifted/lowered to ensure that his/

her feet are never positioned under the raised lift platform. The operator should also keep his/her hands

clear of the lift system during operation.

TRANSPORT VEHICLE POSITIONING

Be sure your vehicle is parked on ﬂat, level ground before attempting to load, lift, or remove a mobility

device with the Backpacker Lift System. Make sure the vehicle emergency park brake is engaged

before loading or unloading a mobility device.

Backpacker Series www.pridemobility.com 9

III. INSTALLATION

BACKPACKER LIFT SYSTEM INSTALLATION

WARNING! The Backpacker Lift System should be installed by an authorized service technician only.

WARNING! At least two people should lift the Backpacker into the rear of the vehicle. Use proper

lifting techniques and avoid lifting beyond your physical capability.

WARNING! Avoid pinch points! Do not hold the lift frame by the pivot points when installing the

Backpacker.

NOTE: Use only the supplied hardware to install the Backpacker Lift System.

Follow these steps for installation:

1. Install the Backpacker securement system to the vehicle. Refer to the installation instructions

supplied with the securement system.

NOTE: Securement systems vary depending on vehicle manufacturer. Pride recommends use of

only the securement system provided with the lift and that you follow any instructions provided

by the manufacturer for installation.

NOTE: If your Backpacker is equipped with caps, the caps can be removed if additional clearance

is needed.

2. Connect the lift system to a power source. See “Wiring Harness Installation.”

NOTE: The lift system is equipped with an optional onboard battery, refer to “Onboard Battery

Installation.”

3. Ensure that all mounting hardware is fully tightened once the lift has been centered and all required

clearances have been achieved.

NOTE: If there is not adequate clearance between the bumper and the platform frame, you may

need to install an end support bracket. Remove the Backpacker from the van and install the end

support bracket close to the rear door opening. Reinstall the lift into the vehicle, making sure

that the bolts protruding from the bottom plate of the Backpacker closest to the vehicle door

snap into the tapped holes on the top of the end support bracket.

NOTE: It may be required to trim the rear inside sill to achieve the adequate platform clearance

with the platform under load.

NOTE: Pay attention to the path of the lift platform during operation. Make sure the lift does

not rub against or interfere with the vehicle in any way. If you notice any contact between the

lift platform and the vehicle, stop lift operation immediately and contact your authorized Pride

Provider for assistance.

4. Run the Backpacker through an entire lift cycle. Lower the platform to the ground and raise the

platform to the fully stowed position in the vehicle. See IV. “Operation.”

NOTE: Ensure the yellow transit screw and washer have been removed from the front of the lift

and the rubber bushing has been installed before operation. See ﬁgures 1 and 2.

WARNING! Remove the transit screw and washer prior to lift operation. Failure to do so may result

in serious equipment damage.

10 www.pridemobility.com Backpacker Series

III. INSTALLATION

Figure 1. Transit Screw Removal

WARNING! Release the “DOWN” button when

the lift platform touches the ground. Do not

allow the motor to run after the lift platform

has touched the ground. Allowing the motor

to run will increase the pressure on the lift

platform and may result in product or vehicle

damage.

Wiring Harness Installation

The wiring harness is approximately 25 ft. (7.62 meters)

long and will accommodate most vehicles.

NOTE: You may wish to perform a practice run

before installing the wiring harness. Route a piece

of light rope (equivalent to the gage of the wiring

harness) along the anticipated path observing

contact points, potential rubbing/chaﬁng points,

and any sharp edges. Remove sharp edges with

a ﬁne grade ﬁle, then treat the steel with a rust

inhibitor or metal sealant.

WARNING! Route the wiring harness through

the vehicle rather than under the vehicle to

avoid coming in contact with sharp edges,

extreme temperatures, moving parts, and

roadway debris. Power shorts may occur if

wires come in contact with hot exhaust or

sharp edges.

WARNING! Never attach the wiring harness to

a secondary power source. Do not attempt to

use trailer wiring to power the lift system. The

wiring harness must be connected directly to

the vehicle battery.

Follow these steps to route the Backpacker Series

wiring harness:

1. Route the lift system wiring harness (starting at the

lift) through the interior of the vehicle. See ﬁgure 3.

TRANSIT SCREW

WASHER

Figure 2. Rubber Bushing Location/Installation

WARNING! Avoid routing the wire harness where it will interfere with or become pinched by the

securement system.

2. Conceal the harness behind or under the interior panels (there should be existing holes). Be certain

that the harness is protected with a rubber grommet when passing it through the metal panels and

into the engine compartment.

3. Inside the engine compartment, secure the harness to the ﬁrewall and the inner fender with plastic

wire tires. Use care not to cause abrasions to the wiring harness. It is important to secure the wiring

harness at various points along its run of the vehicle.

WARNING! Do not cut or shorten the wiring harness. If the harness is too long, coil the excess wire

and secure it with plastic wire ties.

4. Remove the 15-amp fuse from the wiring harness. See ﬁgure 3.

5. Connect the red wire to the positive (+) terminal and the black (grounding) wire to the negative (-)

terminal of the vehicle battery.

RUBBER BUSHING

Backpacker Series www.pridemobility.com 11

III. INSTALLATION

LIFT WIRING

CONNECTION

Figure 3. Wiring Harness Installation - Backpacker Plus

VEHICLE BATTERY

GROUNDING WIRE

FUSE

HAND CONTROL

6. Reinstall the 15-amp fuse to the wiring harness.

WARNING! Before operating the lift, inspect the wiring harness for proper routing and grounding.

Improper routing can cause damage to the harness, and improper grounding can cause damage to

the electrical system.

Optional onboard battery pack installation

The optional onboard battery is designed for easy

installation as it does not require wires to be routed

through or under the vehicle. If using the optional TYPE

II onboard battery pack, please refer to the manual

supplied with the pack for proper operating instructions

and harness connections.

Follow these steps to install the onboard battery

(Type I)

1. Remove the nuts and washers from the protruding

bolts on the side of the lift motor housing. See ﬁgure 4.

2. Slide the spacer bar onto the protruding bolts, if not

already installed.

3. Mount the battery case onto the protruding bolts

and secure into position with the nuts and rubber

caps removed earlier. See ﬁgure 4.

4. Insert the onboard battery into the battery case,

making sure that the connector on the bottom of

the battery aligns and fully connects with the mating

connector inside the battery case.

5. Connect the male connector on the battery cable to

the female connector at the base of the Backpacker.

6. Secure the battery cable to the other cables with

wire ties.

Figure 4. Onboard Battery installation (Type I)

NUTS

SPACER BAR

12 www.pridemobility.com Backpacker Series

III. INSTALLATION

Follow these steps to adjust the wheel chocks:

1. Remove the wheel chocks.

2. Drive your mobility device onto the lift platform, positioning it as near to the center as possible.

3. Position the wheel chocks on the platform. Scooters: Place a wheel chock in front of the front

wheel(s) and behind the rear wheels or behind the front wheel(s) and in front of the rear wheels.

Power Chairs: Place a wheel chock in front of the drive wheels and behind the drive wheels.

4. Take note of the adjustment holes the wheel chocks align with on the platform and remove the

chocks.

NOTE: For larger scooters, the wheel chocks may be positioned to the inside of each wheel.

5. Remove the mobility device from the lift platform.

6. Raise the platform high enough to be able to install hardware from beneath it.

7. Place the wheel chocks onto the lift platform and secure them with the supplied bolts and nuts.

NOTE: Make sure the mobility device is properly secured with the Y-strap before operating the

lift or transporting the mobility device.

ALIGN PLATFORM

HOLES TO DESIRED

WIDTH

Figure 5. Backpacker AVP Platform Adjustment

ADJUSTABLE

WING

BOLT

NUT

BOLT

NUT

Backpacker AVP platform adjustment

The Backpacker AVP is equipped with an adjustment

platform that can be lengthened or shortened to

accommodate a wide range of mobility devices. See

ﬁgure 5.

Follow these steps to adjust the platform:

1. Remove the nuts and bolts that secure the adjustable

wings to the main platform.

2. Move the adjustable wings to the desired width.

3. Align the adjustment holes of the wings with the

holes of the main platform.

4. Reinstall the nuts and bolts, and tighten.

Wheel Chock Installation

Your lift is supplied with two adjustable wheel chocks

that aid in centering your mobility device during loading.

See ﬁgure 6 or 7.

Backpacker Series www.pridemobility.com 13

III. INSTALLATION

Figure 6. Backpacker AVP Wheel Chock Installation

Figure 7. Backpacker Plus Wheel Chock Installation

ADJUSTABLE

HOLES

WHEEL

CHOCK

BOLT

NUT

ADJUSTABLE

HOLES

WHEEL

CHOCK

BOLT

SPACER

BAR

14 www.pridemobility.com Backpacker Series

IV. OPERATION

BACKPACKER LIFT SYSTEM OPERATION

The Backpacker Lift System is designed to lift an

unoccupied mobility device from the ground into the

cargo area of an SUV or full-sized/mini van for the

purpose of easy transport.

WARNING! The Backpacker Lift System is

intended for the transport of unoccupied

mobility devices only. Do not sit on the

mobility device while activating the lift or

during transport.

WARNING! Make sure the lift system is clean,

dry, and free of obstructions before operating.

NOTE: Prior to carrying your mobility device for the

ﬁrst time, ensure the platform will remain level with

the device on it.

Steps to level the platform:

1. Place the mobility device on the platform. The

weight of the device will determine the amount of

adjusting needed.

2. Remove the device from the platform for easy

access to the three adjustment bolts located where

the platform connects to the lowering arm. See ﬁgure 8.

3. Use a 3/16 Allen key to turn the adjustment bolts

as needed to level the platform. Make the same

adjustment to all three adjustment bolts.

4. After leveling the platform for your current mobility

device, additional adjustments will not be necessary

until a different mobility device will be carried.

Follow these steps to load a mobility device with

the Backpacker Lift System.

1. Press and hold the “DOWN” button. See ﬁgure 9.

The lift will move the vehicle to its farthest forward

stop, then lower to the ground. Once the platform

has reached the ground, release the “DOWN”

button.

WARNING! Release the “DOWN” button when

the lift platform touches the ground. Do not

allow the motor to run after the lift platform has

touched the ground. Allowing the motor to run

will increase the pressure on the lift platform

and may result in product or vehicle damage.

NOTE: The lift motor is equipped with a slip clutch,

which emits a ratcheting noise at the end of each

horizontal (in and out) movement. This sound is

normal and does not indicate a problem with your

lift system.

Figure 8. Platform Adjustment Bolts

Figure 9. Hand Control

Backpacker Series www.pridemobility.com 15

IV. OPERATION

Figure 10. Y–strap Positioning

WARNING! Maintain a safe distance from

the lift platform. Ensure your feet are not

positioned under the lift platform and keep

your hands clear of the lift system during

operation.

2. Set the speed control to the slowest setting and

carefully drive the mobility device onto the lift

platform, being sure to center the mobility device

between the previously installed wheel chocks.

NOTE: You may wish to load the mobility device

while standing next to it using the manual freewheel

feature. Refer to the mobility device owner’s manual

for more information on manual freewheel mode.

3. Shut down the power to the mobility device, remove

the key if applicable, and make sure the unit is in

drive mode (drive motors engaged). Refer to the

mobility device owner’s manual for more information

on drive mode.

WARNING! Never leave a mobility device in

freewheel mode during lift system transport,

as the mobility device could roll or shift on its

own.

4. Secure the mobility device to the platform by draping

the Y-strap over the seat and buckling the strap

securely. See ﬁgure 10.

WARNING! Ensure the area behind the lift is

clear of obstructions.

WARNING! Never attempt to secure the Y-strap

over the seat back or armrests of the mobility

device.

MANDATORY! Always secure the mobility

device to the lift with the Y-strap before lift

system operation or vehicle transport.

5. Pull the end of the strap tightly to remove any excess

slack over the seat.

NOTE: Inspect the Y-strap before each use to

ensure there are no signs of fraying or wear.

Ensure that the mobility device is secured properly

before transport. Pride is not liable for damage or

loss resulting from improper securing of a mobility

device.

6. Press and hold the “UP” button. See ﬁgure 9. The

lift will move up to its highest lift point, then slide into

the SUV or van. Once the mobility device is stowed

completely within the vehicle, release the button.

16 www.pridemobility.com Backpacker Series

IV. OPERATION

NOTE: Ensure that the SUV or van has enough

headroom to accommodate the height of the

mobility device before loading it into the vehicle.

Lower the tiller, adjust the seat back angle, or

remove the seat if necessary. Refer to the mobility

device owner’s manual for more information on

these adjustments.

WARNING! Do not exceed the load limits

of your vehicle as speciﬁed by the vehicle

manufacturer.

WARNING! Do not sit on your mobility device

while it is in a moving vehicle.

When you are ready to remove the mobility device from

the vehicle, lower the platform to the ground, unfasten

the Y-strap, and drive the mobility device off of the

platform. Once unloading is complete, return the lift

platform into the vehicle.

MANUAL OVERRIDE OPERATION

The lift is equipped with a manual override feature

that, in the event of a power failure, allows the lift to

be manually positioned. Using the supplied tools, it is

possible to elevate or lower the platform (Backpacker

AVP only), raise or lower the tower arm, and move the

lift forward or backward.

NOTE: The tools needed for manual operation are

included with the lift system. (Drill not included.)

The Backpacker lift platform can be raised/lowered

from the adjustment point located at the top of the lift

(see ﬁgure 11).

NOTE: Some lifts have only a single adjustment

opening on the motor. See ﬁgure 12.

PROHIBITED! DO NOT use the ﬂex-shaft when

manually raising or lowering the lift platform

while using the method illustrated in ﬁgure 11.

Attach the needed hardware directly to the

drill.

PROHIBITED! Never manually move the lift

backward with the lift platform in the lowered

position. Ensure the lift platform is fully raised

and

the tower arm is completely retracted. See

ﬁgure 14.

Figure 11. Raise or Lower the Platform. DO NOT

use the Flex-Shaft for this Operation

Figure 12. Raise or Lower the Platform (Single

Adjustment Opening)

HARDWARE

LIFT PLATFORM

CAPS

Backpacker Series www.pridemobility.com 17

IV. OPERATION

To operate the manual override:

1. Secure the appropriate end of the ﬂex-shaft to a drill, and depending on which part of the lift you

want to move, attach the appropriate hardware to the other end of the ﬂex-shaft. See ﬁgures

11, 12 13, and 14.

2. Insert the ﬂex-shaft into the appropriate adjustment opening of the lift.

3. Operate the drill to ensure the lift is moving in the desired direction. Change the spin direction of the

drill if needed.

4. Operate the drill until the lift reaches the desired position.

NOTE: When a power drill is not available, the manual adjustment wrench can be used. See

ﬁgure 15. Attach the small opening of the manual adjustment wrench to the ﬂex-shaft or hex

hardware and rotate manually in the direction in which you want the lift to move.

Figure 13. Raise or Lower the Tower Arm Figure 14. Front-to-Back Movement

Figure 15. Manual Adjustment Wrench

HARDWARE

TOWER ARM

HARDWARE

*Either of the two wrenches may come with your lift. They perform the same function.

HARDWARE

18 www.pridemobility.com Backpacker Series

IV. OPERATION

PUDDLE LIGHT

Your lift system may be equipped with a puddle light for

safety and convenience.

To operate the puddle light:

1. To activate the puddle light, press the button on

the right side of the lift system hand control for 1

second (see ﬁgure 16), then release. The puddle

light will activate. The puddle light will remain active

while the lift system is in use and for 10 seconds

after the lift system stops.

2. To deactivate the puddle light, press the button on

the right side of the lift system hand control again

for 1 second then release.

WARNING! Ensure the motor of your vehicle

is running while operating the lift system.

Operating your lift system when your vehicle

is not running may drain your car battery.

WARNING! Never run a vehicle inside an

enclosure/garage due to toxic gasses.

NOTE: The puddle light will ﬂash three (3) times

then beep three (3) times continuously if there

is a low battery voltage condition. If this occurs,

your car battery may be low. Allow the vehicle

to run for 15 minutes to charge the battery. If the

“low voltage” warning continues, contact your

automotive service provider to check the battery.

LOCK/UNLOCK LIFT SYSTEM

To Lock lift system:

1. Using the wired hand control, press and hold the

left “lock” button for approximately ﬁve seconds.

The puddle light will ﬂash once, and the unit will

beep once. Release the lock button.

To unlock lift system:

1. Using the wired hand control, press and hold the

left “lock” button for approximately ﬁve seconds.

The LEDs will ﬂash twice, and the unit will beep

twice. Release the lock button.

Safety Latch Switch

Your lift system may be equipped with a safety latch

switch. The safety latch switch will prevent your lift

system from operating in the event that your vehicle’s

trunk or hatch is closed.

NOTE: The lift system should only be operated

when your vehicle’s trunk or hatch is open.

Figure 16. Hand Control

Figure 17. Safety Latch

ACTIVATE PUDDLE

LIGHT

LOCK/UNLOCK

Backpacker Series www.pridemobility.com 19

IV. OPERATION

PROTECTIVE CHAIN

Your lift system is equipped with a protective chain

that moves along the outer guide of the chain rail

(see ﬁgure 18). Ensure that the chain rail is free

of obstruction at all times. If the protective chain

encounters an obstruction or becomes loose, run the

lift to the rear-most position to automatically realign the

lift system.

WARNING! Avoid contact with the protective

chain and chain rail. Ensure that the chain rail

is free of obstruction at all times.

Figure 18. Protective Chain

PROTECTIVE

CHAIN

20 www.pridemobility.com Backpacker Series

TROUBLESHOOTING

Any electromechanical device occasionally requires some troubleshooting. However, most of the

problems that may arise can usually be solved with a bit of thought and common sense. Many of these

problems occur because the battery is not fully charged or because the battery is worn down and can

no longer hold a charge.

What if the motor on my lift system will not operate?

■ Make sure the onboard battery or vehicle battery is fully charged.

■ Make sure all connections to the motor and battery are secure.

■ Check the wiring harness for signs of wear and decay. Replace the harness if necessary.

What if the lift system operates slowly up and or down?

■ Make sure the onboard battery or vehicle battery is fully charged.

■ Make sure all connections to the motor and battery are secure.

■ Check the wiring harness for signs of wear or decay. Replace the harness if necessary. Please see

the provider.

What if the lift platform does not lower completely to the ground?

Check to make sure that area under the lift platform is free of obstructions.

What if my wireless pendant will not operate?

■ Make sure that your vehicle’s hatch is fully open. If the safety hatch switch is activated, your lift

system will not operate.

■ Ensure that the wireless pendant is programmed to work with your lift system. This supplemental

information is provided with the Wireless Pendant. See “Programming the Wireless Pendant.”

■ If the hand control is fully operational but the wireless pendant does not work, the battery may need

to be changed. See “Battery Replacement.”

What if my lift system stops working?

■ Make sure the onboard battery or vehicle battery is fully charged.

■ Make sure all connections to the motor and battery are secure.

■ Check the wiring harness for signs of wear and decay. Contact your authorized Pride provider to

replace the harness if necessary.

■ Ensure that the wireless pendant is properly programmed to the lift system. Reset the circuit board

and reprogram the wireless pendant. This supplemental information is provided with the Wireless

Pendant. See “Programming the Wireless Pendant.”

NOTE: The puddle light will ﬂash three (3) times then beep three (3) times continuously if there

is a low battery voltage condition. If this occurs, your car battery may be low. Contact your

automotive service provider to check or replace the battery.

V. TROUBLESHOOTING

La page charge ...

Pride Backpacker Plus Le manuel du propriétaire

Marque: Pride

Modèle: Backpacker Plus

Taper: Le manuel du propriétaire

Ce manuel convient également à

Backpacker AVP 2.0

Télécharger le PDF

rapport

dans d''autres langues

English: Pride Backpacker Plus Owner's manual

Pride Backpacker Plus Le manuel du propriétaire

Ce manuel convient également à

Pride Backpacker Plus Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents