Snooper 6 series Manuel utilisateur

User manual

Benutzerhandbuch

Guide de l’utilisateur du

Gebruikershandleiding

Manual del usuario

Manuale per l’utente

6 SERIES

7” Screen Portable Satellite Navigation System

User manual

2 • EN

Return to contents

Introduction

Congratulations on buying the 6 SERIES Portable Navigator and Fixed Speed Camera location system.

6 SERIES utilises the very latest Global Positioning Satellite (GPS) technology to provide you with accurate street level navigation

via clear and precise voice prompts as well as alerting you to potentially hazardous stretches of road, accident black spots and ﬁxed

speed safety cameras.

The most accurate digital mapping available is provided by

whilst the geographical coordinates of all ‘ﬁxed’ speed

monitoring systems and many oﬃcially designated accident ‘hotspots’ have been stored on a database provided by AURA™. The

AURA™ Database is the most comprehensive available, providing cover, not only in the UK and Ireland, but throughout Western

Europe and North America. The database is constantly monitored and updated by the AURA™ data collection team, ensuring that

you are alerted to every potentially hazardous stretch of road and all ﬁxed speed safety cameras.

6 SERIES comes with an SD Card that contains the navigation software. The SD Card can be activated in seconds by inserting the

card into the SD slot on the left hand side of the unit. When necessary, upgrades to this mapping data will be made available for you.

Mapping updates are chargeable, please visit www.snooperneo.co.uk for further details.

As the AURA™ camera database changes daily, regular updates to 6 SERIES are required. 6 SERIES connects quickly and easily to

your PC so that you can download the database in a matter of minutes (internet connection required). Please note: In order for

the software to be installed successfully, there are certain minimum hardware and software requirements needed; see the section

‘System Requirements & Downloading’ later in this manual.

Once the database has been downloaded 6 SERIES compares your position using its built-in GPS antenna, with the position of every

known ‘ﬁxed’ speed monitoring system and accident ‘hotspot’ alerting you both audibly and visually with voice alerts and full colour

graphics on the units LCD screen ensuring your highest concentration at all times.

Please note that AURA™ updates are subject to a subscription charge. Please refer to the subscription and download section

of this manual for further details or visit www.snooperneo.co.uk.

Drive Safely with Snooper!

6 SERIES’ camera location technology has been designed and manufactured to help enhance road safety and is in no way a licence

to speed nor has it been designed as a substitute for concentration. Driving within the speed limit, whilst carefully observing current

road conditions is essential.

6 SERIES

3 • EN

Return to contents

Contents

Page

4 What’s included?

5 Overview

6 Registering 6 SERIES

7 Quick Start Guide to Navigation

9 Start Up – Installing the SD Card

System Requirements and Downloading

10 Downloading the AURA™ Camera Database

11 Installing 6 SERIES

12 Power Connection & Charging

13 Charging the internal battery

Powering 6 SERIES using the built-in battery

15 Satelite Navigation

16 Easy Setup

Screen Settings

18 Volume

19. Setting Vehicle Parameters Truckmate

20. Setting Vehicle Parameters Ventura

21 Planning a Route

By Full Postcode

22 Find by City

23 Home

24 Oﬃce

Recent Route or Clear Route

25 Multi-route

28 Find by Favourites

Recent Destinations

29 Find by Points of Interest (POI)

31 Find by Nearest POI

32 User POI

35 Find by Map

36 Find by coordinate

Re-Route

37 Avoid by Road Name

Avoid by Range

38 Clear Avoided Road

39 Your Route

40 Route Description

TMC

43 Campsite Search Ventura ONLY

44 My Favourite Menu

Favourites

46 Recent Destination

47 Home

48 Oﬃce

49 Conﬁgure Menu

50 Truckmate Setting up vehicle perameters

51 Ventura Setting up vehicle perameters

52 Volume

Change Language

Setup

2D/3D/North

Page

53 Speed/Time

MPH/KMH

Arrival Time/Remaining Time

55 Show POI

Auto Scale

56 Camera Alert

Display Cameras

Alert Sound

57 School

Alert

58 Touch Tone

Route Alert

My Speed

59 Change Map Colour

Qwerty Keyboard

60 TMC

61 GPS Status

System Security Code

Conﬁguration Security Code

62 Save user point

Route Timer

63 Version (Hardware & Software)

Route Option

Shortest Time

Shortest Distance

64 Avoid Tollway

Avoid Motorway

Navigate Avoiding Road

Avoid by Road Name

Avoid by Range

65 Clear Avoided Road

Navigate via Location

66 Change Start Position

Summary Screen

Quick Access Menu

67 Volume

Scroll Map

Day or Night Settings

Camera Alerts

Magnify or Reduce Function

68 Understanding the Mapping Screen

69 Bluetooth

70 Phonebook

71 Options

Dialpad

72 Messages

Filemanager

73 Troubleshooting 6 SERIES Downloads

76 Speciﬁcation

79 Accessories

Service Under Warranty



6 SERIES

4 • EN

Return to contents

What’s included?

1 x 6 SERIES satellite navigation system

1 x Micro-SD Card

1 x Windscreen Mounting Bracket

1 x Home Charger

1 x In-car Charger

1 x USB Cable with USB Host Cable

1 x USB Download Cable

1 x TMC Antenna

1 x CD ROM

This user guide explains the functionality of all 3 variants of the 6 SERIES, these symbols will illustrate if the feature is relevant to your

device

Truckmate

Ventura

Syrius

PLEASE NOTE

Due to our desire to continually improve our products, the speciﬁcation may change without notice.

6 SERIES

5 • EN

Return to contents

Overview

1. Power Button

Press and hold to switch on or oﬀ.

2 Touch screen LCD

3. Earphone jack (Earphones not included)

4. Micro-SD Card Slot

5. TMC Socket

6. USB Socket

7. Speaker (on the back of the unit)

6 SERIES

1

3

4

7

6

5

2

6 • EN

Return to contents

Registering 6 SERIES

IMPORTANT!

PLEASE READ BEFORE USING 6 SERIES.

To enable 6 SERIES to locate Fixed Speed Cameras and Accident Black spots you will have to register and download the AURA™

Camera Database.

Register Online

Go to the oﬃcial website www.snooperneo.co.uk and register your unit online. Your unit should normally be activated within 30

minutes of registration.

Please Note: To register 6 SERIES you will need the serial number of your unit which can be found on the back of the device.

Monthly Debit or Credit Card payment of £2.99 inc VAT*

Quarterly Debit or Credit Card payment of £7.99 inc VAT*

Annual Debit or Credit Card payment of £29.99 inc VAT

*Minimum subscription term of 12 months.

PLEASE NOTE

Due to our desire to continually improve our products, the speciﬁcation may change without notice.

7 • EN

Return to contents

Quick Start Guide to Navigation

1. Take the 6 SERIES outside so that the GPS receiver can locate

your position. This may take between 15 - 30 minutes the

ﬁrst time. When satellite lock is achieved, the screen will

display your current position on its map in a ‘3D’ navigation

view. Your position (and direction) is indicated by the

icon.

Tip: To reduce the ‘cold start’ GPS time remain stationary

2. Bring up the main navigation menu by touching the centre

of the display.

Select

Find by Post Code

Tip: The icon always means that there are more options

to see on the next screen

3. You will see a standard browser screen, used for entering

postcodes. Enter the full UK postcode using the keyboard

and press

IMPORTANT: Use the key to

separate the two segments of the postcode.

6 SERIES

8 • EN

Return to contents

TTip: The default route options are set to Quickest Route.

To change the route options refer to Section 6 in this user

manual.

4. Press

and 6 SERIES will calculate the

fastest route from your current position to your destination.

This should only take a short time and a progress bar is

shown on the screen.

5. A journey summary screen will then be

displayed

Please note: The summary screen is only

displayed for approximately 10 seconds

before the unit automatically begins to

provide you with turn-by-turn instructions.

6. Press

The navigation view will now be displayed, but with the

route now highlighted for you. As you approach a speciﬁc

turn in the calculated route, 6 SERIES will advise you what

to do. For example, “After 200 yards, turn left”, followed

by “Now turn left”. As you proceed along your journey,

following the voice instructions, you will notice that the

navigation view is updated constantly, always showing

approaching roads and junctions and presenting the best

route to you.

Tip: If you miss a turn or drive down the wrong road, a

new fastest route will be calculated automatically, based

on your new position and direction of travel, a tone will

be heard to conﬁrm re-routing. 6 SERIES will always give

you clear instructions that will take you to your chosen

destination.

Final Destination Estimated arrival Time

Your current

location

Distance to

destination

Estimated

journey time

Refer to section 6.0

on page 63 for details

9 • EN

Return to contents

Start Up – Installing the SD Card

Before using the 6 SERIES, you will need to install the Micro-SD Card included with the

device. The Micro-SD Card comes complete with digital mapping and is also where the

AURA™ camera database is stored if you choose to subscribe and download it.

Start by removing the Micro-SD Card from its packaging and insert it into the Micro-

SD Card slot as indicated. Switch on the device by pressing and holding the standby

power button located on the top right hand side of the unit for 2 seconds. The 6 SERIES

will automatically synchronise with the Micro-SD Card. Once the synchronisation is

completed, the Micro-SD Card will not function with any other device. 6 SERIES is now

ready to navigate and the camera database can be downloaded if necessary.

Please note that if the unit does not activate when you press and hold the standby power button for 2 seconds it may require

charging. Refer to the section ‘Charging the internal battery’ later in this manual.

System Requirements and Downloading

Before you can begin to download the database onto 6 SERIES, you will need to install the 6 SERIES Updater software provided on the

software CD.

In order for the software to be installed successfully, there are certain minimum hardware and software requirements needed.

Minimum Hardware Requirements

The computer must have an Intel Pentium Class processor or equivalent, a minimum of 32MB of RAM, a monitor with 256 (8-bit)

colours or greater, a CD ROM drive, 20MB of free disc space and a spare USB connection.

Minimum Software Requirements

The software will only operate on the following Windows based operating systems:

Windows XP (32 bit)

Windows Vista

Windows 7

and, in addition, will only work with Internet Explorer 6 or Netscape Navigator 6 or above.

NOTE: 6 SERIES Updater software does not support Windows 95, 98, Millennium, 2000 or Apple Macintosh operating

systems. Windows XP (64 bit) systems is also not supported.

Software Installation Instructions

Place the Software CD into a CD ROM or DVD drive. Your PC should automatically open a window displaying the instructions for

installing the software. Follow the instructions onscreen to install the speed camera updater software.

To launch the CD manually: Click on ‘Start’ and then ‘Run’. In the dialogue box that opens click on ‘Browse’ – another dialogue box

will open. Locate your CD ROM or DVD drive (drive letter is normally D) using the ‘Look in’ option and select ‘6 SERIES’ from the lower

portion of the dialogue box. Once you have selected ‘6 SERIES’ click on ‘Open’ on the explorer box and then ‘OK’ on the Run dialogue

box.

Please make sure that the operating system installs the new hardware ﬁrst before installing the Camera Updater software. Once the

updater software has been installed click ‘Finish’ and then close the CD auto run window. After installing the software, double click

the camera updater program icon on your desktop to start it. Select your ‘Language’, ‘Vehicle Type’ (if applicable) and ‘Download

Settings’ when prompted.

Any updates to the speed camera updater software can be obtained from www.snooperneo.co.uk/software.cfm. If you have any

problems using this software please call 0333 240 1000 during oﬃce hours and select Option 3.

Once the software is installed, you are ready to download the speed camera database onto 6 SERIES. Once the initial setup is

completed the speed camera updater software window is displayed on your desktop.

10 • EN

Return to contents

Downloading the AURA™ Camera Database

Please Note: You must register 6 SERIES before you can perform a download.

Performing a download is simple.

1. Power up 6 SERIES by pressing and holding the power button for 2

seconds and ensure that the computer is connected to the Internet.

2*. Double click on the camera updater icon on your desktop and left

click ’Menu’ and then ‘Download Settings’.

3*. Select the ﬁles you wish to download (UK Cameras is selected by

default). Once you have selected the ﬁles you wish to download left

click the ‘OK’ button.

4. Connect the 6 SERIES using the USB cable provided. Please ensure

that you do not use the lead with the USB host connection as the

download will not work.

5. The updater software will then start to run automatically and

download the database ﬁles that you have selected onto your unit.

The download process is as follows:

 The software will display the serial number of the 6 SERIES and a green progress bar will start to progress across the screen.

 The software will then connect to our database server and then download** the speed camera database.

 The 6 SERIES will then save the data received.

 The software will indicate that the download is complete and will

instruct you to disconnect the 6 SERIES from your PC. Close the

camera updater program by clicking the ‘x’ situated in the top right

hand corner of the updater window.

*You only need to do these steps if you wish to change the data that

is downloaded onto the 6 SERIES. If you want the download settings to be

the same as the previous download ignore these two steps.

**If you have a Firewall on your computer, the Firewall software may inform you that the updater software is trying to access the

internet. Please make sure that you grant/allow/permit access to the updater program through the Firewall.

Please read the messages supplied by your Firewall software carefully before choosing your option. If you do not allow the program

to access the internet through the Firewall, the download process will fail.

Plug the

USB cable into

the USB socket on the

right hand side

of the 6 SERIES

11 • EN

Return to contents

Installing 6 SERIES

6 SERIES comes with a windscreen bracket so that the unit can be mounted onto your vehicles windscreen.

When installing 6 SERIES please ensure that:

 The unit, with its built in GPS antenna has a clear view of the sky*

 It is located in a position where you can easily view the LCD display without having to take your eyes too far from the road ahead

and that you can reach the controls safely.

 Does not interfere with the vehicles controls

 Does not jeopardise the drivers or passengers safety

 You will be able to remove the device to perform downloads.

PLEASE NOTE: Be careful to choose a location that does not block the drivers view or where it might endanger the driver or

passengers should your vehicle suddenly come to a stop or be involved in an accident.

Installing 6 SERIES using the Windscreen Suction Cup bracket

You can mount 6 SERIES to the inside of your vehicles windscreen using the

windscreen bracket provided.

Clean the area where you wish to position the bracket thoroughly with a good quality

glass cleaner. This allows a more secure seal on the windscreen.

 Place the suction cup and bracket on the windscreen and push the locking lever

towards the windscreen to secure the bracket.

 Adjust the angle of the bracket so that when the unit is attached to it you can view

the display and operate the controls safely.

 Position 6 SERIES onto the bracket, by inserting the bottom of the unit ﬁrst and

ﬁnally clipping the top of the bracket into the slot on the top of the unit. To remove

6 SERIES, simply unclip the unit by pushing the top of the bracket and taking the

unit from the holder.

 6 SERIES can be powered directly either from the internal battery if it is fully

charged or powered from the cigarette lighter socket. To use the cigarette lighter

socket, plug the USB connector on one end of the power cable into the USB socket

on the right hand side of 6 SERIES and plug the larger plug into the cigarette lighter

socket of your vehicle.

Please Note: Only use the cigarette lighter power cable provided with 6 SERIES. 6 SERIES operates on 5V and using any other

cigarette lighter power cable will damage your device and void the warranty.

Locking

lever

Bracket

adjusters

12 • EN

Return to contents

Power Connection & Charging

Powering and charging 6 SERIES from the cigarette lighter socket

6 SERIES comes with a power cable designed to plug into your vehicles cigarette lighter socket. The power cable is suitable for both

12v DC and 24v DC vehicles. This lead will power the device but will also charge 6 SERIES’s internal battery.

1. Plug the smaller end of the lead into the USB socket on the right hand side of 6 SERIES

2. Plug the other end of the cigarette lighter adaptor into your vehicles cigarette lighter socket.

3. Press and hold the standby power switch on the top left hand side for two seconds to switch the device ON.

Please Note: Do not leave 6 SERIES plugged into the cigarette lighter socket when you start your vehicle. The cigarette lighter

socket is prone to power surges as the vehicle is started and this may cause damage to your unit.

If 6 SERIES does not power up please check that the cigarette lighter socket is clean of any debris, remembering not to insert metal

objects into the socket. Check that the cigarette lighter adaptor is inserted all the way into the socket and check that the fuse in the

cigarette lighter adaptor is operational. If 6 SERIES will still not power up, please check that the cigarette lighter in your vehicle is

functioning correctly.

Replacing the Fuse

If 6 SERIES stops operating, the fuse in the cigarette lighter plug may have blown . If it has blown, follow these steps and replace it

with a 3 amp, 5mm x 20mm fast acting fuse.

Caution: Using a fuse that does not meet these ratings or defeating fuse protection can damage your unit, the power

cable, or the vehicles electrical system.

1. Grasp the ring near the tip of the cigarette lighter plug, and then carefully unscrew the ring by turning it counter clockwise.

Caution: If you must use pliers to loosen the ring, be careful not to crush the tip. Never use pliers or other tools to retighten the

ring on the cigarette lighter plug.

2. Pull the ring straight out, then remove the metal tip and old fuse.

3. Check the fuse to see if it has blown. If it has, replace it.

4. Replace the metal tip inside the ring, then place the fuse inside the cigarette lighter plug and screw the ring back onto the plug.

Make sure the metal tip is visible when you reassemble the cigarette lighter plug.

13 • EN

Return to contents

Plug the charger into a

240V AC mains socket

Charging the internal battery

Although 6 SERIES can be charged using the cigarette lighter in your vehicle, a

complete charge is more easily achieved by using the 240V AC mains charger

included. When new, the battery contains a nominal charge.

To charge the unit fully, connect the 240V AC mains charger as indicated in the

picture on the right. The 6 SERIES will take approximately 3 hours to charge.

Note: The new battery’s full performance is only achieved after two or three

complete charges and discharges.

Powering 6 SERIES using the built-in battery

Once 6 SERIES is fully charged, it is ready for use. Press and hold the standby/power switch on the top left hand side of the unit for 2

seconds to switch on the device.

ON/OFF

switch

Plug the

charger cable into

the USB socket on the

right hand side

of the 6 SERIES

14 • EN

Return to contents

Low Battery Warning

If 6 SERIES is powered from the internal battery and the ‘Battery Low – Please

Recharge’ warning is displayed on the screen, the unit has a few minutes of

battery power remaining. You should either connect the cigarette lighter

adaptor lead to the unit whilst in the vehicle or recharge the battery from the

mains adapter supplied.

WARNING: PLEASE DO NOT USE OR LEAVE 6 SERIES IN EITHER WET OR HUMID CONDITIONS, OR IN EXTREME TEMPERATURES,

AS THIS COULD PERMANENTLY DAMAGE THE UNIT AND THE BATTERY. WHEN NOT IN USE DO NOT LEAVE THE UNIT ATTACHED

TO THE WINDSCREEN, ESPECIALLY WHEN THE WEATHER IS WARM, TO AVOID DAMAGE TO THE UNIT AND ALSO REDUCE THE

RISK OF THEFT.

CAUTION: THERE IS A RISK OF EXPLOSION IF THE BATTERY IS REPLACED WITH AN UNAPPROVED TYPE. USING THE WRONG

TYPE OF BATTERY MAY DAMAGE YOUR UNIT AND INVALIDATE YOUR WARRANTY. ONLY SNOOPER AUTHORISED PERSONNEL

SHOULD REPLACE THE BATTERY. PLEASE DISPOSE OF USED BATTERIES ACCORDING TO LOCAL WASTE MANAGEMENT RULES AND

REGULATIONS. FURTHER INFORMATION CAN BE FOUND LATER IN THIS USER MANUAL.

PLEASE NOTE

Due to our desire to continually improve our products, the speciﬁcation may change without notice.

15 • EN

Return to contents

Satellite Navigation

1.Starting Up

Once you have synchronised the Micro-SD Card and

performed a download as necessary it is time to perform

the ﬁrst Start Up. First make sure your vehicle is parked in

as open a space as possible, clear of tall trees and buildings

so that the built in GPS antenna has a clear view of the sky

above. Next switch ON the unit by pressing and holding the

standby power switch on the top left hand side of the unit for

2 seconds.

The following warning will be displayed.

Please read the warning and select the relevant vehicle type (where applicable).

Press “I Agree”

to continue.

Whilst 6 SERIES software is loading a start-up display will be shown for just a few seconds and then the screen will show a section of

a map. 6 SERIES needs to acquire a minimum of four satellites in order to work. Once this has been achieved 6 SERIES will ascertain

your position and this will be indicated by a green arrow icon on the on-screen map and the GPS signal strength will be shown in the

bottom right hand corner of the display. 6 SERIES is now ready to navigate.

As the GPS engine and antenna have never been used before, the ﬁrst ‘Cold’ start can take anywhere from 15 – 30 minutes to

establish a satellite connection. Once initialised, subsequent start ups will take less time and eventually should take only a matter

of minutes.

2. Easy Set Up

2.1 Screen settings

There are a number of map views or diﬀerent types of information that can be displayed on the screen at any one time:-

Screen views

3D 2D North

1

2

3

4

5

6

7

8

9

10

11

16 • EN

Return to contents

Lane Guidance.

Snoopers’ advanced lane guidance will assist the driver by clarifying which lane the vehicle should be using.

Snooper has extensive coverage of motorway, complex junctions, some dual carriage way exits and some inner

city junctions. The criteria for lane guidance is that the turning lanes or exit lanes will have more than ONE lane

to be included.

My Speed

The speed limit of nearly every road across Europe can now be clearly displayed on your 6 SERIES at all times.

Choose between speed limits for cars and advisory speed limits for trucks from 3.5t and over. In addition, My

Speed can also be set to alert you if you accidentally exceed the speed limit at any time. Inappropriate speed is

often responsible for many road accidents resulting in serious injuries which some times can even be fatal. MY-

SPEED will ensure that you know what the speed limit is on every road you travel on so you can drive safely at all

times.

The text will show RED when the speed limit is exceeded

My Speed sounds an audible alert speed limit is exceeded and the current speed

3

Indicator will change

from Black to RED text. Refer to page 60 for full details and settings

3

or Current speed or time - Press to change the displayed information.

4

Indicates the current direction of travel

5

Current road name or road number.

6

Distance to destination

7

or

Displays the Estimated Time of arrival or remaining journey time. Press to change the displayed information.

8

Current battery status

9

Current satellite signal strenth

10

This pop up box will be displayed when The indicator will count down the distance.

the driver needs to take ‘action’ eg move

to the left in 0.59 miles.

11

Route timer. Set Route timer to alert you when you need to take a break. Set the maximum driving time

allowed and set the advanced warning time you require before your next break is due. The Route timer clock

will keep you advised of the driving time you have left and will automatically alert you when it’s time to take a

break. Refer to page 64 for details.

1

2

PLEASE NOTE: These are advisory speed limits ONLY. Always check local road side speed limit signs and abide by local

driving regulations and laws of the country you are driving in. It is the responsibility of the driver of the vehicle to ensure

that they are driving within the posted speed limit at ALL times

17 • EN

Return to contents

Additional warning or information pop ups will appear at the bottom left hand corner of the screen. If lane guidance is displayed

then the warning pop ups will be displayed at the top left hand side of the screen.

or ONLY - Restriction and warnings will be displayed in the bottom left hand side of the screen, if lane guidance is also

being displayed the restriction and/or warning will be displayed in the top left hand corner of the screen.

Junction view

Full screen images of main

motorway junctions are

displayed in advance to help

you navigate more safely.

These junction view images

will be displayed on the

screen for approximately 5

seconds

Examples of Junction view.

Restrictions

Height

Width

Length

Weight

No trucks allowed

No trailers

No U-turn for trucks

No right turn for trucks

No left turn for trucks

Trucks with hazardous

goods forbidden

Trucks with natural goods

harmful to water forbidden

Warning

Steep road up ahead

Steep road down ahead

Tight bend ahead

Side winds

Risk of grounding

18 • EN

Return to contents

To modify the information shown:

 Press the centre of the screen to access the menu.

 Press the ‘Conﬁgure’ button.

 Press the icon where you will see the list of options below.

 Select the option you wish to change on the left.

 To change a setting, simply press on the tick box to indicate which option you would like to choose.

 Continue to select each option and select your preference.

 Press ‘OK’ at the bottom of the screen to save your preferences.

Your chosen settings will now be saved and will appear on the screen each time you use 6 SERIES. If you want to switch between your

Current Speed and the Atomic Clock or the Estimated Time of Arrival and Time to Destination during your journey simply touch the

screen where either piece of information is displayed and the unit will display the alternate setting and vice versa. However each time

you power the device up the original setting will be displayed.

2.2

Volume Control

The volume can be adjusted using this function within the ‘Conﬁgure’

menu. To adjust the volume:

 Press the centre of the screen to access the ‘Menu’.

 Press ‘Conﬁgure’.

 Press the ‘Volume Control’ icon.

 To increase the volume press the icon.

 To decrease the volume press the icon.

 To test the volume before saving, press the ‘Test’ icon.

 To reset the volume to the factory default press the ‘Reset’ icon.

 Press ‘OK’ at the bottom of the screen to save your setting.

Note: The arrow icon in the bottom right hand corner of the display will return you to the ‘Conﬁgure’ menu if pressed but will

not store any changes you have made. You need to select the ‘OK’ button in order to save your changes.

use the up

and down

arrows

to scroll to

other options

19 • EN

Return to contents

Setting up vehicle parameters

For Ventura to calculate a route suitable for your vehicle it needs to know certain information about the vehicle itself such as its

height, weight and width. It is possible to save the settings of 10 diﬀerent vehicles. Follow these instructions to enter your vehicles

details.

Press the centre of the screen to access the menu, press ‘Conﬁgure’ and then press the ‘Caravan/Motorhome’ icon.

Name: Enter the name here.

Height: Enter the height of the vehicle here.

Length: Enter the length of the vehicle here.

Weight: Enter the weight of the vehicle here.

Width: Enter the width of the vehicle here.

Weight per axle: Enter the weight per axle of

the vehicle here

Vehicle type:

 Fixed Axle: Standard setting for ﬁxed axle vehicles.

 Trailer: Speciﬁc traﬃc rules exist for vehicles towing caravans. For example, there are roads that are forbidden for towing vehicles.

These will be avoided.

La page charge ...

Snooper 6 series Manuel utilisateur

Snooper 6 series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents