Briteq BT-METEOR Le manuel du propriétaire

Catégorie
Projecteurs
Taper
Le manuel du propriétaire
ENGLISH
USER MANUAL
BRITEQ
®
1/74
BT-METEOR
OPERATION MANUAL
Thank you for buying this Briteq
®
product. To take full advantage of all possibilities and for your own safety,
please read these operating instructions very carefully before you start using this unit.
FEATURES
Compact and extremely bright LED moving head for Pro DJ, renting companies and discotheques
Based on the very latest 100WATT LED technology for:
Extremely high light output: 110’500 lux @ 1m !
Very low power consumption
Virtually no heat production
Very smooth 0-100% dimming and different strobe effects
6 rotating, exchangeable gobos + open
Independent color wheel with split color function (8 colors + white)
Rotating, indexable 3 facet prism.
DMX-controlled focus
Excellent built-in programs for wonderful, ever changing, light shows.
Multiple working modes:
DMX-control: via 5, 11 or 14 channels
SMART-MSL: several BT-METEOR units can work in audio synchronized master/slave, while the user
only needs 5 DMX-channels to keep full control over colors, gobos, strobe, dimming and pan/tilt speed.
Standalone: sound activated with internal mic.
Master/slave: wonderful synchronized shows in standalone mode
Prepared for wireless DMX: just plug-in an optional WTR-DMX DONGLE ! (optional, Briteq
®
code 4546)
Three different default settings, easy for rental companies:
PRO-defaults: basic settings for use on professional DMX-controllers.
AUTO-defaults: basic settings for easy master/slave use.
USER-defaults: save and recall your own preferred settings!
Automatic X/Y re-positioning
Temperature controlled fan for extremely low noise operation
Easy software updates via special software upgrade unit
Alphanumeric LCD-display for easy menu navigation
Adjustable beam angle: 12° to 16°
Neutrik PowerCON
®
in/outputs: easy daisy chaining of several units up to 16A.
Equipped with omega brackets for fast installation
BEFORE USE
Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
BT-METEOR unit
Omega clamp
Power cable
Operating instructions
ENGLISH
USER MANUAL
BRITEQ
®
2/74
BT-METEOR
SAFETY INSTRUCTIONS:
To protect the environment, please try to recycle the packing material as much as possible.
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
This unit is for indoor use only.
Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign
object enters the unit, immediately disconnect the mains power.
Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls.
Don’t cover any ventilation openings as this may result in overheating.
Prevent use in dusty environments and clean the unit regularly.
Keep the unit away from children.
Inexperienced persons should not operate this device.
Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Allow the device about 10 minutes to cool down before to start servicing.
Always unplug the unit when it is not used for a longer time or before to start servicing.
The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
Check that the available voltage is not higher than the one stated on the unit.
The power cord should always be in perfect condition. Switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Never let the power-cord come into contact with other cables!
This fixture must be earthed in order to comply with safety regulations.
Don’t connect the unit to any dimmer pack.
Always use an appropriate and certified safety cable when installing the unit.
In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.
Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
The housing and the lenses must be replaced if they are visibly damaged.
Please use the original packing when the device is to be transported.
Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering
from epilepsy.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use or the presence of un-insulated dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
The device is not suitable for direct mounting on normally flammable surfaces. (suitable only for
mounting on non-combustible surfaces)
CAUTION: Do not stare at operating lamp.
May be harmful to the eyes.
ENGLISH
USER MANUAL
BRITEQ
®
3/74
BT-METEOR
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
Always use a certified safety cable (number 3 on the picture) that can hold
12 times the weight of the device when installing the unit. This secondary
safety attachment should be installed in a way that no part of the installation
can drop more than 20cm if the main attachment fails.
The device should be well fixed; a free-swinging mounting is dangerous and
may not be considered!
Don’t cover any ventilation openings as this may result in overheating.
The operator has to make sure that the safety-relating and machine-
technical installations are approved by an expert before using them for the
first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
A. Holes to fix the special omega clamp (included)
B. Holes to fix an optional safety cable
HOW TO SET UP THE UNIT
CONTROL PANEL:
1. DISPLAY shows the various menus and the selected functions.
2. BUTTONS
[MODE]
To select the programming functions
To go backward in the selected functions
To go forward in the selected functions
[ENTER]
To confirm the selected functions
3. MAINS FUSE: this fuse only protects the electronics of the projector,
mains input/output (7) is not fused.
4. MAINS INPUT / OUTPUT: with PowerCON
®
sockets, connect the
supplied mains cable here, you can daisy chain several units, up to max
16A. Input and output are connected to each other without any fuse.
Hint: Please check our website for special cable assemblies that contain both power (3x1.5mm² with
Neutrik PowerCON
®
) and balanced signal (XLR 3pin) in one cable. Different lengths are available: 1.3m,
3m, 5m and 10m, very convenient!
5. DMX IN/OUTPUTS: used for DMX512 linking, you can use good quality balanced signal cables with 3pin
XLR-connectors.
ENGLISH
USER MANUAL
BRITEQ
®
4/74
BT-METEOR
6. M-DMX INPUT: Please note that this USB-connector is NOT used for updates or to connect the unit to a
PC! Instead this USB-connector makes it very easy to add wireless DMX to the unit! Just add the
(optional) WTR-DMX DONGLE from BRITEQ
®
and you will get wireless DMX! Moreover you will be able
to connect other DMX-controlled equipment to the DMX-output so you can share the wireless DMX
function with all connected units! No extra settings to be made in the setup menu, just follow the
procedure in the user manual supplied with the WTR-DMX DONGLE from BRITEQ
®
. The separate
WTR-DMX DONGLE is available from WWW.BRITEQ-LIGHTING.COM (order code: 4645)
7. OMEGA CLAMP BASE: base with fixing points for the omega clamp + safety cable, see previous
chapter “overhead rigging”
8. BEAM ANGLE ADJUSTMENT: you can adjust the beam angle seamlessly between 1and 16° by
simply turning the lens.
MAIN MENU:
To select any of the functions, press the [MODE] button to enter the setup menu.
Use the ▼/▲ buttons to browse the menu.
Select a function with the [ENTER] button.
Use the ▼/▲ buttons to change the mode.
Once the required mode is selected, press the [ENTER] button to select.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode. If you
don’t do this, the setting will not be stored and after some time, the fixture will return to the previous
running mode.
DMX Address
Used to set the starting address in a DMX setup.
Press the [MODE] button and use the ▼/ buttons until
[DMX Addr] is shown on the display.
Press the [ENTER] button to start editing.
Use the ▼/▲ buttons to change the DMX512 address.
Once the correct address shows on the display, press the
[ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the
setting and to return to running mode.
Channel mode
Used to set the desired channel setup mode.
Press the [MODE] button and use the ▼/▲ buttons until
[Ch. Mode] is shown on the display.
Press the [ENTER] button to start editing.
Use the ▼/▲ buttons to choose 5MSL (SMART-MSL), 11
or 14ch mode.
Once the desired channel setup mode shows on the
display, press the [ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the
setting and to return to running mode.
Show Mode
Used to choose the Show mode when used in standalone
or master/slave mode.
Press the [MODE] button and use the ▼/▲ buttons until
[ShowMode] is showing on the display.
Press the [ENTER] button to start editing.
Use the ▼/▲ buttons to select one of the available shows:
[Floor]: Fixture is placed on the floor. [PAN/TILT]
movements are not limited.
[Ceiling]: Fixture is fixed on the ceiling. [TILT]
movements are limited to ±60°.
[Stage FL]: Fixture is placed on a stage, in front of the audience. The spot is always projecting
towards the audience’s direction; i.e. in front of the stage. [PAN] movement angle (left to right to left):
160°. [TILT] movement angle: 90° (60° above horizon; 3 below horizon.)
[Stage CE]: Fixture is fixed upside-down on the ceiling of a stage. The spot is mainly projecting
ENGLISH
USER MANUAL
BRITEQ
®
5/74
BT-METEOR
towards the audience in front of the stage. [PAN] movement angle (left to right to left):160°. [TILT]
movement angle: 90° (vertically, front 75°; back 15°)
Once the right mode is shown on the display, press the [ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode.
Split Color
You can select if the unit can only show full colors or also split colors.
Press the [MODE] button and use the ▼/▲ buttons until [SplitCol] is shown on the display.
Press the [ENTER] button to start editing.
Use ▼/▲ button to select “Yes” (Split colors) or “No” (only full colors).
Once the right mode is shown on the display, press the [ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode.
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
Press the [MODE] button and use the ▼/▲ buttons until [SlaveMod] is shown on the display.
Press the [ENTER] button to start editing.
Use ▼/▲ button to select [SLAVE1] (normal) or [SLAVE2] (2 light show) mode.
Once the right mode is shown on the display, press the [ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode.
NO DMX / [Blackout] Mode
Here you can decide how the unit should behave when no DMX-signal is detected..
Press the [MODE] button and use the ▼/▲ buttons until [No DMX] is shown on the display.
Press the [ENTER] button to start editing.
Use the ▼/▲ buttons to select one of the available options:
[BL. OUT]: the projector goes in blackout mode and waits until the DMX-signal returns.
[FREEZE]: the projector shows the last valid DMX-signal and waits in that position until the DMX-
signal returns.
[SOUND]: the projector starts working in sound activated mode (standalone or master/slave mode).
Once the right mode is shown on the display, press the [ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode.
Sound Sensitivity
Used to set the sensitivity of the internal microphone
Press the [MODE] button and use the ▼/▲ buttons until [Sound] is shown on the display.
Press the [ENTER] button to start editing.
Use ▼/▲ button to choose a value between “0” (very low sensitivity) and “100” (high sensitivity).
Once the right value is shown on the display, press the [ENTER] button select it.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode.
[PAN] Inversion
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
Press the [MODE] button and use the ▼/▲ buttons until [Pan Inv] is shown on the display.
Press the [ENTER] button to start editing.
Use ▼/▲ button to select “No” (normal) or “Yes” (pan inversion) mode.
Once the mode is selected, press the [ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode.
[TILT] Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
Press the [MODE] button and use the ▼/▲ buttons until [Tilt Inv] is shown on the display.
Press the [ENTER] button to start editing.
Use ▼/▲ button to choose “No” (normal) or “Yes” (tilt inversion) mode.
Once the right mode is shown on the display, press the [ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode.
ENGLISH
USER MANUAL
BRITEQ
®
6/74
BT-METEOR
Display backlight on/off
Backlight on: display is always lit.
Backlight off: display is dark when not used.
Press the [MODE] button and use the ▼/▲ buttons until the display shows [Display].
Press the [ENTER] button to start editing.
Use the ▼/▲ buttons to select “On” (display always lit) or “Off(display dark when not used).
Once the right mode is shown on the display, press the
[ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the
setting and to return to running mode.
Focus Adjust
Used to help you adjusting the focus of the rotating gobos
while the fixture is used in standalone or master/slave
mode.
You can set the focus of the gobos in different directions.
While working in auto/audio mode the fixture will continuously
try to keep the gobos sharp in the different directions. Please
note that this is not always possible, so the gobos will not
always be perfectly sharp.
Press the [MODE] button and use the ▼/buttons until the
display shows [Focus].
Press the [ENTER] button so the unit goes to the “tilt 90°”
position (Adj1).
Press the [ENTER] button so the unit goes to the “pan
position (Adj2).
Press the [ENTER] button so the unit goes to the “pan 90°”
position (Adj3).
Press the [ENTER] button so the unit goes to the “pan 180°”
position (Adj4).
Press the [ENTER] button so the unit goes to the “pan 270°”
position (Adj5).
In the Previous 5 steps you are able to adjust the focus with
the / buttons on the unit (the display shows the current
focus status).
Press the [MODE] button for about 2 seconds to store the
setting and to return to running mode.
Function Delay
On the Function channel (CH11 or CH14) you can select
some special functions, like “blackout during gobo
change” and others. With this option you can select the
delay before a selected function becomes active.
IMPORTANT INFORMATION: the function delay can only be set to zero seconds (no Delay) when you are
using a DMX-controller or DMX-software using presets for the DMX-values of the special functions.
Never use “no Delay” while using a simple DMX-controller with faders to set the functions manually!
Press the [MODE] button and use the ▼/▲ buttons until [F. Delay] is shown on the display.
Press the [ENTER] button to start editing.
Use ▼/▲ button to choose a value between [NO DELAY] / [1sDELAY] / [2s Delay] or [3s Delay]
Once the right delay is shown on the display, press the [ENTER] button select it.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode.
Dimmer Curve
Used to set the dimmer curve of the master dimmer.
Press the [MODE] button and use the ▼/▲ buttons until [DimCurve] is shown on the display.
Press the [ENTER] button to start editing.
Use the ▼/▲ buttons to select one of the available options:
ENGLISH
USER MANUAL
BRITEQ
®
7/74
BT-METEOR
Once the dimmer curve is shown on the display, press the [ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode.
FAN Speed
On some occasions fan noise should be reduced to a minimum. Therefore you set three different fan
speed modes.
Press the [MODE] button and use the ▼/▲ buttons until [FanSpeed] is shown on the display.
Press the [ENTER] button to start editing.
Use the ▼/▲ buttons to select one of the available options:
[Auto]: the fan speed will be automatically adjusted to always have the best balance between fan
noise and performance (light output).
[Low]: the fan speed will always be low to reduce fan noise to a minimum. (use in theatres,
conference rooms, …). However this means that the LED temperature could become too high: in that
case the LED current will be reduced automatically to protect the LED. This means that the light output
will also be lower.
[High]: the LED will be well cooled so maximum light output can be guaranteed under all conditions.
However this means that fan noise will be higher than usual. While used in discotheques and in hot
summertime conditions this should not be a problem.
Once the right mode is shown on the display, press the [ENTER] button to confirm.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode.
LED Temperature
Used to show the temperature of the LED
Press the [MODE] button and use the ▼/▲ buttons until the display shows [LED Temp].
Press the [ENTER] button to show the temperature on the display.
To go back to the functions press the [MODE] button again.
If you want to go back to normal running mode: press the [MODE] button for about 2 seconds.
ERROR Information
Used to show eventual error information.
Press the [MODE] button and use the ▼/▲ buttons until the display shows [LED Temp].
Press the [ENTER] button to show the error information on the display.
To go back to the functions press the [MODE] button again.
If you want to go back to normal running mode: press the [MODE] button for about 2 seconds.
Auto Test
Used to activate the internal “self-test” program which checks all possibilities of the unit.
Press the [MODE] button and use the ▼/▲ buttons until the display shows [AutoTest].
Press the [ENTER] button to start the internal self-test program.
To go back to the functions press the [MODE] button.
Fixture Time
Used to show the number of working hours of the unit.
Press the [MODE] button and use the ▼/▲ buttons until the display shows [Hours:].
Press the [ENTER] button to show the number of working hours on the display.
To go back to the functions press the [MODE] button.
Defaults
Used to choose between 2 sets of default settings, often used by rental companies.
Additionally you can also save and recall your own set of preferred settings.
Press the [MODE] button and use the ▼/▲ buttons until the display shows [Defaults].
Press the [ENTER] button to start editing.
ENGLISH
USER MANUAL
BRITEQ
®
8/74
BT-METEOR
Use the ▼/▲ buttons to select one of the available options:
[PRO def]: basic settings for use on professional DMX-controllers, see the list of defaults in the chart.
[AUTO def]: basic settings for easy master/slave use, see the list of defaults in the chart.
[USER def]: you can save / recall your own set of preferred settings.
PARAMETER name
PRO defaults
AUTO defaults
USER defaults
DMX Channel mode
14 ch
5 MSL
Specified by the user
Show mode
Floor
Floor
Specified by the user
Split color mode
Yes
Yes
Specified by the user
Slave mode
SL 1
SL 1
Specified by the user
No DMX mode
Freeze
Sound
Specified by the user
Sound sensitivity
60
60
Specified by the user
PAN inversion
No
No
Specified by the user
TILT inversion
No
No
Specified by the user
Display on/off
OFF
on
Specified by the user
FOCUS Adjust
Value 127
Value 140
Specified by the user
Function Delay
3 sec
3 sec
Specified by the user
FanSpeed
Auto
Auto
Specified by the user
Dimmer curve
SQUARE
SQUARE
Specified by the user
Loading PRO or AUTO defaults:
Use the ▼/▲ buttons to select either [AUTO def] or [PRO def] and press [ENTER] to confirm.
Display shows [Load]: press [ENTER] to confirm (or [MODE] to return).
To avoid that current settings are overwritten by accident the display shows by default [NO].
Use the ▼/▲ buttons to select [YES] and confirm with [ENTER].
The default settings are now loaded.
If you want to go back to normal running mode: press the [MODE] button for about 2 seconds.
Loading, saving and editing USER-defaults:
EDITING: Starting from the PRO and AUTO defaults you can easily make your own [USER] settings: just
make your changes in the setup menu (refer to the table to see which settings are saved).
SAVING: Once the settings are OK, just save them to the personal [USER]defaults:
Use the ▼/▲ buttons to select [USER def] and press [ENTER] to confirm.
Display shows [Load]: use the ▼/▲ buttons to select [Save] and press [ENTER] to confirm.
To avoid that current settings are overwritten by accident the display shows by default [NO].
Use the ▼/▲ buttons to select [YES] and confirm with [ENTER].
Your new settings are now saved to [USER def] (user defaults memory).
If you want to go back to normal running mode: press the [MODE] button for about 2 seconds.
LOADING: same actions as for saving the settings but now you choose the [Load] option (loading).
Reset
Used to force a full or partial reset of the unit.
Press the [MODE] button and use the ▼/▲ buttons until the display shows [Reset].
Press the [ENTER] button: the display shows [All] (reset all functions)
Press the [ENTER] button again to reset the unit.
OR
Use the ▼/▲ buttons to select the function that you want to reset. You can do a partial reset of the
following functions: [Pan & Tilt], [Color], [Gobos], [Prism] and [Focus].
Press [ENTER] to reset the selected function: the display shows [Reset …] as long as the reset takes.
If you want to go back to normal running mode: press the [MODE] button for about 2 seconds.
Note: you can also perform a full reset by DMX. Choose DMX-value 200-209 on the “Special functions
channel (channel 11 or 14), see the DMX-chart for more information.
Firmware version
Used to show the software version that is installed in the unit
Press the [MODE] button and use the ▼/▲ buttons until the display shows [Firmware].
Press the [ENTER] button to show the software version on the display.
To go back to the functions press the [MODE] button.
ENGLISH
USER MANUAL
BRITEQ
®
9/74
BT-METEOR
OFFSET MENU:
This is a hidden menu where you can fine-tune the offset of several functions. To access this menu do as
follows: press the [ENTER] button for about 3seconds while you are in the SETUP menu (any option, not
important). Now the OFFSET menu (calibration menu) shows up:
Use the ▼/▲ buttons to browse the menu.
Select a function with the [ENTER] button.
Use the ▼/▲ buttons to change the values.
Press the [ENTER] button to select.
Press the [MODE] button for about 2 seconds to store the setting and to return to running mode. If you
don’t do this, the setting will not be stored and after some time, the fixture will return to the previous
running mode.
Dimmer Calibration
Due to tolerances in the production process, not all LEDs have exactly the same brightness,
therefore you can use this option to match the Brightness of different machines.
Use the ▼/▲ buttons until [Calibrat LED] is shown on the display.
Press the [ENTER] button to start editing.
Use the ▼/▲ buttons to select a value between “50” (lowest brightness) and “100” (highest brightness).
Once the desired brightness is found, press the [ENTER] button to confirm.
Note: the default value is 100, a new value cannot be saved to
the USER-defaults.
Offset Adjust men t of different functions
Used to adjust the home position of several functions:
Make sure that the unit is connected to a DMX-controller and set
to 14CH channel mode: set ch6 + ch7 to maximum.
If you’re not already in the setup menu, just press the [MODE]
button shortly to enter the setup menu.
Now press the [ENTER] button for at least 3 seconds to open
the offset menu.
Use the ▼/▲ buttons to select the function that you want to
adjust, options are:
[PAN]: offset PAN movements
[TILT]: offset TILT movements
[COL]: offset COLOR-wheel
[GOBO]: offset GOBO-wheel
[RGOB]: offset of GOBO rotation
[PRI]: offset of the prism
[RPRI]: offset of the prism rotation
[FOCU]: offset of the FOCUS function.
Press the [ENTER] button to start editing.
Use the ▼/▲ buttons to adjust the offset value.
Press the [ENTER] button to select your setting.
When all offset adjustments are done, press the [MODE] button
for about 2 seconds to store them and to return to running mode.
ELECTRICAL INSTALLATION + ADDRESSING
Important: The electrical installation should be carried out by qualified personal only,
according to the regulations for electrical and mechanical safety in your country.
Electrical installation for 1 standalone unit:
Just insert the mains cable. The unit starts working immediately in stand-alone mode.
Remark: if there’s no output, please make sure to set the option [No DMX] of the projector to [SOUND]
(audio mode) and sound sensitivity [Sound] to a value over 50 (see previous chapter).
ENGLISH
USER MANUAL
BRITEQ
®
10/74
BT-METEOR
Electrical installation for two or more units in master/slave:
In this mode the units will show a synchronized show, working to the rhythm of the beat.
Connect 2 to maximum 16 units together using good quality balanced microphone cables. The first unit
in the chain will automatically act as the master, the other units will act automatically as slaves.
Make sure that all units are connected to the mains.
Done!
Remark: if there’s no output, please make sure to set the option [No DMX] of the projector to [SOUND]
(audio mode) and sound sensitivity [Sound] to a value over 50 (see previous chapter).
Electrical installation for two or more units in SMART-MSL:
In this mode the units will show a synchronized show, working to the rhythm of the beat but you can still
control some functions on the master using only 5 DMX-channels.
To assure proper operation you need an optional “Mini DMX-SPLITTER” to isolate the master/slave line
from the main DMX-line, see drawing.
Connect 2 to maximum 16 units together using good quality balanced microphone cables. The first unit in
the chain will act as the master, the other units will act automatically as slaves.
Set the master to 5MSL (SMART-MSL) channel mode (see previous chapter).
For the DMX-controller the master and its slaves can now be considered as 1 virtual effect that needs a
start address so it can be controlled as any other DMX-unit in the DMX chain: see “DMX Address” in the
chapter “Main Menu” to see how you can set the DMX-start address.
Make sure that all units are connected to the mains.
Set the DMX-controller according to the DMX-chart below.
Done!
Remark: in order to work well to the rhythm of the music, make sure to set the [No DMX] mode of the
MASTER projector to [SOUND] and sound sensitivity [Sound] to a value over 50 (see previous chapter).
DMX-Chart for 5MSL (SMART-MSL) working mode
1 DIM
2 - STROBE
3 - COLOR
4 - GOBO
5 - PAN/TILT SPEED
VALUE
FUNCTION
VALUE
FUNCTION
VALUE
FUNCTION
VALUE
FUNCTION
VALUE
FUNCTION
10
255
100%
255
FAST STROBE
218-255
ORIGINAL
COLORS
218-255
ORIGINAL GOBOS
255
AUDIO FAST
9
8
188-217
COLOR 7
188-217
GOBO 7
7
158-187
COLOR 6
158-187
GOBO 6
RANDOM
6
128-157
COLOR 5
128-157
GOBO 5
PROGRAM
5
098-127
COLOR 4
098-127
GOBO 4
AUDIO TRIGGERED
4
068
SLOW STROBE
068-097
COLOR 3
068-097
GOBO 3
3
038-067
SOUND STROBE
038-067
COLOR 2
038-067
GOBO 2
2
008
0%
008-037
RANDOM STROBE
008-037
COLOR 1
008-037
GOBO 1
008
AUDIO VERY SLOW
1
000-007
STANDBY
000-007
OPEN
000-007
WHITE
000-007
NO GOBO
000-007
HOLD (FREEZE)
Electrical installation in DMX-mode:
The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
“daisy chain” your DMX controller and all the connected units with a good quality balanced cable.
Both XLR-3pin and XLR-5pin connectors are used, however XLR-3pin is more popular because these
cables are compatible with balanced audio cables.
ENGLISH
USER MANUAL
BRITEQ
®
11/74
BT-METEOR
Pin layout XLR-3pin:
Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+)
Pin layout XLR-5pin:
Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+) ~ Pins4+5 not used.
To prevent strange behavior of the light effects, due to interferences, you must use a 90Ω to 120Ω
terminator at the end of the chain. Never use Y-splitter cables, this simply won’t
work!
Make sure that all units are connected to the mains.
Each light effect in the chain needs to have its proper starting address so it knows
which commands from the controller it has to decode. In the next section you will
learn how to set the DMX addresses.
HOW TO SET THE RIGHT STARTING ADDRESS:
Refer to the previous chapter (DMX-512 address setting) to learn how to set the starting address on this unit.
The starting address of each unit is very important. Unfortunately it is impossible to tell you in this user
manual which starting addresses you have to set because this completely depends on the controller you will
use… So please refer to the user manual of your DMX-controller to find out which starting addresses you
must set.
DMX-CONFIGURATION IN 11CH + 14CH MODE:
11CH
14CH
VALUE
FUNCTION
1
1
000 - 255
Pan
2
000 - 255
Pan Fine (Least significant bit)
2
3
000 - 255
Tilt
4
000 - 255
Tilt Fine (Least significant bit)
5
000 - 255
Pan / Tilt Speed (000 = fast ~ 255 = slow)
3
6
000 - 255
Dimmer (0 to 100%)
4
7
Strobe / Shutter effect
000 - 007
Shutter closed (no output)
008 - 015
Shutter open
016 - 131
Strobe 1 (slow → fast)
132 - 139
Shutter open
140 - 181
Strobe 2: slow open / instant close (slow → fast)
182 - 189
Shutter open
190 - 231
Strobe 3: instant open / slow close (slow → fast)
232 - 239
Shutter open
240 - 247
Strobe 4: random strobe (slow → fast)
248 - 255
Shutter open
5
NORMAL
8
NORMAL
Color wheel
000 - 014
COLOR 1: White (open)
015 - 028
COLOR 2: Red
029 - 042
COLOR 3: Orange
043 - 056
COLOR 4: Yellow
057 - 070
COLOR 5: Green
071 - 084
COLOR 6: Blue
085 - 098
COLOR 7: Magenta
099 - 112
COLOR 8: Light Blue
113 - 127
COLOR 9: Pink
128 - 189
Color wheel turning clockwise (fast → slow)
190 - 193
Color wheel stops turning
194 - 255
Color wheel turning counter clockwise (slow → fast)
5
SPLIT
8
SPLIT
Color wheel
000 - 007
COLOR 1: White (open)
008 - 014
COLOR 1 + 2
ENGLISH
USER MANUAL
BRITEQ
®
12/74
BT-METEOR
COLOR
COLOR
015 - 022
COLOR 2: Red
023 - 029
COLOR 2 + 3
030 - 037
COLOR 3: Orange
038 - 044
COLOR 3 + 4
045 - 052
COLOR 4: Yellow
053 - 059
COLOR 4 + 5
060 - 067
COLOR 5: Green
068 - 074
COLOR 5 + 6
075 - 082
COLOR 6: Blue
083 - 089
COLOR 6 + 7
090 - 097
COLOR 7: Magenta
098 - 104
COLOR 7 + 8
105 - 112
COLOR 8: Light Blue
113 - 119
COLOR 8 + 9
120 - 127
COLOR 9: Pink
128 - 189
Color wheel turning clockwise (fast → slow)
190 - 193
Color wheel stops turning
194 - 255
Color wheel turning counter clockwise (slow → fast)
6
9
Gobo Wheel
000 - 007
OPEN (no gobo)
008 - 015
GOBO 1
016 - 023
GOBO 2
024 - 031
GOBO 3
032 - 039
GOBO 4
040 - 047
GOBO 5
048 - 063
GOBO 6
064 - 073
GOBO 1 Shaking
074 - 082
GOBO 2 Shaking
083 - 091
GOBO 3 Shaking
092 - 100
GOBO 4 Shaking
101 - 109
GOBO 5 Shaking
110 - 127
GOBO 6 Shaking
128 - 189
Gobo wheel turning clockwise (fast → slow)
190 - 193
Gobo wheel stops turning
194 - 255
Gobo wheel turning counter clockwise (slow → fast)
7
10
Gobo wheel rotation
000 - 127
indexed positioning: 0° - 360°
128 - 189
Gobo turning clockwise (fast → slow)
190 - 193
Gobo stops turning
194 - 255
Gobo turning counter clockwise (slow → fast)
8
11
Prism
000 - 007
No Effect
008 - 255
Prism Effect
9
12
Prism Rotation
000 - 127
Index position
128 - 189
Prism turning counter clockwise (fast → slow)
190 - 193
No rotation
194 - 255
Prism turning clockwise (slow → fast)
10
13
Focus
000 - 255
Focus setting
11
14
Special functions
000 - 069
No function
070 - 079
Activate blackout during pan/tilt (*)
080 - 089
Disable blackout during pan/tilt (*)
090 - 099
Activate blackout during color change (*)
100 - 109
Disable blackout during color change (*)
110 - 119
Activate blackout during gobo change (*)
120 - 129
Disable blackout during gobo change (*)
ENGLISH
USER MANUAL
BRITEQ
®
13/74
BT-METEOR
130 - 199
No function
200 - 209
Reset all (after 5 seconds delay)
210 - 247
No function
248 - 255
Sound activated automatic mode
Note (*): by default [function delay] (is set to 3seconds: the selected function will only be active while the
corresponding DMX-value is received during at least 3seconds. You can change the [function delay] time in
the setup menu.
MAINTENANCE
Make sure the area below the installation place is free from unwanted persons during servicing.
Switch off the unit, unplug the mains cable and wait until the unit is cooled down.
During inspection the following points should be checked:
All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
Clean with a soft cloth using normal glass cleaning products.
Always dry the parts carefully.
Clean the external optics at least once every 30 days.
Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
Mains Input: AC 100 - 240V, 50/60Hz
Power consumption: 160 Watt (max)
Fuse: 250V 2A slow blow (20mm glass)
Power connections: PowerCon - 16A Power linking capacity.
DMX connections: Neutrik 3pin-XLR male / female
DMX channels used: 11ch + 15ch + 5MSL (SMART-MSL)
Lamp: 100W LED Engine
Color temperature: 9000K
CRI factor: 82
Beam Angle: 12° - 16° (manually adjustable)
Color wheel: 8 colors + open
GOBO wheel: 6 rotating gobos, replaceable by metal and glass gobos
Outer diameter 22.90 mm Image diameter: 19.50 mm
Special effects: 3facet rotating prism
IP-Rating: IP20
Operating temperature (T
a
): 0°C to 40°C
Size: 290 x 180 x 435 mm (LxBxH) head facing upward, see drawing
Weight: 8,5 kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.briteq-lighting.com
FRANÇAIS
GUIDE D’UTILISATION
BRITEQ
®
14/74
BT-METEOR
GUIDE D’UTILISATION
Nous vous remercions d’avoir acheté ce produit Briteq
®
. Pour tirer pleinement profit de toutes les possibilités
du produit et pour votre propre sécurité, lisez attentivement ce mode d’emploi avant d’utiliser cet appareil.
CARACTÉRISTIQUES
Lyre à LED compacte et extrêmement lumineuse pour DJ professionnels, agences de location et
discothèques
Basée sur les dernières technologies LED 100 W pour :
Un éclairage extrêmement puissant : 110’500 lux à 1 m !
Très basse consommation d’énergie
Pratiquement aucune production de chaleur
Fonctions de gradation de 0 à 100 % et différents effets stroboscopiques
6 gobos rotatifs interchangeables + position ouverte
Roue chromatique indépendante avec fonction couleurs adjacentes (8 couleurs + blanc)
Prisme à trois facettes, rotatif et indexable.
Focus (netteté des gobos) contrôlée par DMX
Excellents programmes intégrés offrant de fabuleux jeux de lumière en changement perpétuel.
De nombreux modes de fonctionnement :
Contrôle DMX : via 5, 11 ou 14 canaux
Maître/esclave-DMX : plusieurs BT-METEOR peuvent fonctionner en synchronisation audio
maître/esclave, tandis que l’utilisateur n’a besoin que de cinq canaux DMX pour un contrôle total des
couleurs, des gobos, du stroboscope, de la gradation et de la vitesse de pan/tilt.
Autonome : commande sonore via un micro interne.
Maître/esclave : des jeux de lumière merveilleux et synchronisés en mode autonome
Préparé pour le DMX sans fil: il suffit de brancher un DONGLE WTR-DMX ! (optionnel, Briteq® code 4546)
Trois réglages par défaut différents, faciles pour les entreprises de location :
Réglages par défaut PRO : réglages de base pour une utilisation avec les contrôleurs DMX
professionnels.
Réglages par défaut AUTO : réglages de base pour faciliter l’utilisation du mode maître/esclave.
Réglages par défaut UTILISATEUR : mémorisez et réutilisez vos réglages préférés !
Repositionnement X/Y automatique
Ventilateur à contrôle de température pour un fonctionnement à volume sonore extrêmement faible
Mises à jour du logiciel simples via un adaptateur spécial
Affichage LCD alphanumérique pour une navigation rapide dans les menus
Angle du faisceau réglable : de 12° à 16°
Entrées/sorties Neutrik PowerCon
®
: chaînage facile de plusieurs unités jusqu’à 16 A.
Équipé de supports Omega pour une installation rapide
AVANT UTILISATION
Avant d’utiliser cet appareil, assurez-vous qu’il n’a pas été endommagé durant le transport. En cas de
dommages, n’utilisez pas l’appareil et consultez immédiatement votre revendeur.
Important : Cet appareil est expédié de notre usine en parfait état et correctement emballé. Il est impératif
que l’utilisateur suive strictement les consignes de sécurité et les avertissements se trouvant dans ce
manuel. Tout dommage à une mauvaise manipulation n’est pas couvert par la garantie. Le revendeur
décline toute responsabilité en cas de dysfonctionnement ou de problème à un manquement aux
instructions contenues dans ce manuel.
Conservez ce manuel dans un lieu sûr pour consultation ultérieure. Si vous vendez l’appareil, assurez-
vous de joindre ce manuel.
Vérifiez le contenu :
Vérifiez que le carton contient les éléments suivants :
Unité BT-METEOR
Attache Omega
Cordon d’alimentation
Mode d’emploi
FRANÇAIS
GUIDE D’UTILISATION
BRITEQ
®
15/74
BT-METEOR
CONSIGNES DE SÉCURITÉ :
Pour protéger l’environnement, essayez de recycler autant que possible les matériaux d’emballage.
Pour éviter tout incendie ou électrocution, n’exposez pas cet appareil à la pluie ou à l’humidité.
Pour éviter une formation de condensation interne, laissez l’appareil s’adapter à la température ambiante
quand vous le mettez dans une pièce chaude après le transport. La condensation empêche parfois
l’appareil de fonctionner à plein rendement ou peut même causer des dommages.
Cet appareil est destiné à un usage d’intérieur seulement.
Ne placez pas d’objets métalliques et ne renversez pas de liquides à l’intérieur de l’appareil. Cela
risquerait d’occasionner un choc électrique ou un dysfonctionnement. Si un corps étranger pénètre dans
l’appareil, débranchez immédiatement le cordon d’alimentation de la prise secteur.
Placez l’appareil dans un endroit bien aéré, loin de tout matériau et/ou liquide inflammable. L’appareil doit
être fixé à au moins 50 cm des murs environnants.
Ne couvrez pas les ouvertures de ventilation, cela pourrait entraîner une surchauffe.
Évitez d’utiliser l’appareil dans des environnements poussiéreux et nettoyez-le régulièrement.
Gardez l’appareil hors de portée des enfants.
Les personnes inexpérimentées ne doivent pas utiliser cet appareil.
La température ambiante de fonctionnement maximale est de 40 °C. N’utilisez pas cet appareil à des
températures ambiantes plus élevées.
Assurez-vous qu’aucune personne indésirable ne se trouve en dessous de l’emplacement d’installation
durant le montage, le démontage et l’entretien.
Laissez l’appareil refroidir pendant environ 10 minutes avant de commencer l’entretien.
Débranchez toujours l’appareil lorsque vous ne comptez pas l’utiliser pendant une longue période ou avant
de commencer l’entretien.
L’installation électrique doit être effectuée par un technicien qualifié, conformément à la réglementation en
matière de sécurité électrique et mécanique dans votre pays.
Vérifiez que la tension secteur n’est pas supérieure à celle indiquée sur l’appareil.
Le cordon d’alimentation doit toujours être en parfait état. Éteignez immédiatement l’appareil si le cordon
d’alimentation est écrasé ou endommagé. Celui-ci doit être remplacé par le fabricant, son agent d’entretien
ou une personne de même qualification afin d’éviter tout danger.
Ne laissez jamais le cordon d’alimentation entrer en contact avec d’autres câbles !
Ce luminaire doit être mis à la terre pour être conforme à la réglementation en matière de sécurité.
Ne connectez pas l’appareil à un variateur de lumière.
Utilisez toujours un câble de sécurité approprié et certifié lors de l’installation de l’appareil.
Afin d’éviter un choc électrique, n’ouvrez pas le boîtier. L’appareil ne contient aucun composant réparable
par l’utilisateur.
Ne réparez jamais un fusible et ne court-circuitez jamais le porte-fusible. Remplacez toujours un fusible
endommagé par un fusible de même type ayant les mêmes spécifications électriques !
En cas de problème de fonctionnement important, cessez d’utiliser l’appareil et contactez immédiatement
votre revendeur.
Le symbole représentant un éclair fléché à l’intérieur d’un triangle équilatéral est destiné à alerter
l’utilisateur de la présence de « tensions dangereuses » non isolées à l’intérieur de l’appareil,
d’une magnitude pouvant constituer un risque d’électrocution.
Le symbole représentant un point d’exclamation dans un triangle équilatéral est destiné à avertir
l’utilisateur que d’importants conseils d’utilisation et de maintenance sont fournis dans la
documentation accompagnant l’appareil.
Ce symbole signifie : pour un usage d’intérieur uniquement
Ce symbole signifie : lisez les instructions
Cet appareil n’est pas adapté à un montage direct sur des surfaces normalement inflammables.
(ne convient que pour le montage sur surfaces non combustibles)
ATTENTION : Ne fixez pas votre regard sur une lampe allumée.
Peut être nocif pour les yeux.
FRANÇAIS
GUIDE D’UTILISATION
BRITEQ
®
16/74
BT-METEOR
Le boîtier et les lentilles optiques doivent être remplacés s’ils sont visiblement endommagés.
Utilisez l’emballage d’origine pour transporter l’appareil.
Pour des raisons de sécurité, il est interdit d’apporter des modifications non autorisées à l’appareil.
Important : Ne regardez jamais directement la source de lumière ! N’utilisez pas l’effet en présence de
personnes souffrant d’épilepsie.
SUSPENDRE L’APPAREIL
Important : L’installation doit être effectuée par un technicien qualifuniquement. Une mauvaise
installation peut entraîner des blessures et/ou dommages graves. La suspension de l’appareil
exige une grande expérience ! Les limites de charge utile doivent être respectées, des matériels
d’installation certifiés doivent être utilisés, l’appareil installé doit être inspecté régulièrement pour
vérifier les conditions de sécurité.
Assurez-vous qu’aucune personne indésirable ne se trouve en dessous de l’emplacement d’installation
durant le montage, le démontage et l’entretien.
Fixez l’appareil dans un endroit bien aéré, loin de tout matériau et/ou liquide inflammable. L’appareil doit
être fixé à au moins 50 cm des murs environnants.
L’appareil doit être installé hors de portée des personnes, à l’écart des passages et des endroits des
personnes peuvent aller et venir ou s’asseoir.
Avant de suspendre l’appareil, assurez-vous que le point de suspension peut supporter une charge d’au
moins 10 fois le poids de l’appareil.
Lors de l’installation, utilisez toujours un câble (numéro 3 sur l’image) de
sécurité certifqui peut supporter 12 fois le poids de l’appareil. Ce support
de suspension de sécurité secondaire doit être installé de manière à ce
qu’aucune partie de l’installation ne puisse tomber de plus de 20 cm si le
support principal lâche.
L’appareil doit être bien fixé, un montage balançant est dangereux et ne doit
pas être envisagé !
Ne couvrez pas les ouvertures de ventilation, cela pourrait entraîner une
surchauffe.
L’opérateur doit s’assurer que la sécurité relative à l’installation et les
conditions techniques sont approuvées par un expert avant d’utiliser
l’appareil pour la première fois. Les installations doivent être inspectées
chaque année par une personne qualifiée pour s’assurer que la sécurité est
toujours optimale.
C. Trous pour fixer l’attache spéciale Omega (incluse)
D. Trous pour fixer le câble de sécurité facultatif
FRANÇAIS
GUIDE D’UTILISATION
BRITEQ
®
17/74
BT-METEOR
CONFIGURATION DE L’UNITÉ
PANNEAU DE COMMANDE :
1. L’ÉCRAN affiche les différents menus et les fonctions sélectionnées.
2. TOUCHES
[MODE]
Pour sélectionner les fonctions de programmation
Pour revenir en arrière dans les fonctions
sélectionnées
Pour aller en avant dans les fonctions
sélectionnées
[ENTER]
Pour confirmer les fonctions sélectionnées
3. FUSIBLE SECTEUR : ce fusible ne protège que la partie électronique
du projecteur, l’entrée/sortie (7) secteur n’est pas protégée par un
fusible.
4. ENTRÉE/SORTIE SECTEUR : utilisez les prises PowerCON
®
pour brancher le câble d’alimentation
fourni ici ; vous pouvez connecter plusieurs unités en série, jusqu’à 16 A maximum. Aucun fusible n’est
utilisé au niveau des entrées et sorties raccordées.
Astuce : veuillez consulter notre site Web pour les assemblages de câbles spéciaux qui combinent une
alimentation (3 x 1,5 mm² avec Neutrik PowerCON
®
) et un signal symétrique (XLR 3 broches) dans un
seul câble. Différentes longueurs sont disponibles : 1,3 m, 3 m, 5 m et 10 m, très pratiques !
5. ENTRÉES/SORTIES DMX : utilisées pour le chaînage DMX 512, vous pouvez utiliser des câbles à
signal symétrique de bonne qualité avec connecteurs XLR 3 broches.
6. ENTREE M-DMX : Ce connecteur USB ne sert PAS à effectuer des mises à jour ou à connecter
l’appareil à un ordinateur! Le connecteur USB vous permet d’ajouter aisément le DMX sans fil à
l’appareil ! Il suffit d’y connecter le WTR-DMX DONGLE (optionnel) de la marque BRITEQ
®
et vous
aurez le DMX sans fil prêt à être utilisé ! De plus, si vous reliez d’autres appareils à la sortie DMX filaire
de cet appareil, vous pourrez transférer les données DMX reçues à tous les autres appareils dans la
chaîne DMX ! Il n’y à pas de réglages à faire dans le menu de configuration. Il suffira de suivre la
procédure décrite dans le mode d’emploi qui est livre avec le WTR-DMX DONGLE de BRITEQ
®
. Le
WTR-DMX DONGLE est disponible chez WWW.BRITEQ-LIGHTING.COM (order code: 4645)
7. BASE D’ATTACHE OMEGA : base avec points de fixation pour attache Omega + câble de sécurité, voir
le chapitre précédent intitulé « Suspendre l’appareil »
8. RÉGLAGE DE L’ANGLE DU FAISCEAU : Vous pouvez ajuster l’angle du faisceau de 12° à 16° en
faisant simplement pivoter la lentille.
MENU PRINCIPAL :
Pour sélectionner une fonction, appuyez sur la touche [MODE] afin d’accéder au menu de configuration.
Parcourez le menu à l’aide des touches ▼/▲.
Utilisez la touche [ENTER] pour sélectionner la fonction.
Changez de mode à l’aide des touches ▼/▲.
Une fois le mode désiré sélectionné, appuyez sur la touche [ENTER] pour valider.
Maintenez la touche [MODE] enfoncée pendant environ deux secondes pour mémoriser les réglages et
revenir en mode de fonctionnement normal. Sans cela, le réglage ne sera pas enregistré, et après
quelques instants, l’appareil reviendra au mode de fonctionnement précédent.
FRANÇAIS
GUIDE D’UTILISATION
BRITEQ
®
18/74
BT-METEOR
Adresse DMX
Utilisée pour définir l’adresse de départ dans une configuration DMX.
Appuyez sur la touche [MODE] et utilisez les touches ▼/▲ jusqu’à ce que [DMX Addr] s’affiche à l’écran.
Appuyez sur la touche [ENTER] pour commencer l’édition.
Changez l’adresse du DMX512 à l’aide des touches ▼/▲.
Une fois la bonne adresse affichée à l’écran, appuyez sur la touche [ENTER] pour confirmer.
Maintenez la touche [MODE] enfoncée pendant environ deux secondes pour mémoriser les réglages et
revenir en mode de fonctionnement normal.
Mode canal
Utilisé pour définir le mode de configuration des canaux
souhaité.
Appuyez sur la touche [MODE] et utilisez les touches ▼/▲
jusqu’à ce que [Ch. Mode] s’affiche à l’écran.
Appuyez sur la touche [ENTER] pour commencer l’édition.
Utilisez les touches ▼/▲ pour sélectionner le mode 5MSL
(SMART-MSL), 11 ou 14ch.
Lorsque le mode de configuration des canaux désiré
s’affiche à l’écran, confirmez-le en appuyant sur la touche
[ENTER].
Maintenez la touche [MODE] enfoncée pendant environ
deux secondes pour mémoriser les réglages et revenir en
mode de fonctionnement normal.
Mode Show
Utilisé pour choisir le mode Show lorsqu’il est utilisé en
mode autonome ou maître/esclave.
Appuyez sur la touche [MODE] et utilisez les touches ▼/▲
jusqu’à ce que [ShowMode] s’affiche à l’écran.
Appuyez sur la touche [ENTER] pour commencer l’édition.
Sélectionnez l’un des spectacles de lumière disponible à
l’aide des touches ▼/▲:
[Floor] : le projecteur est placé au sol. Les
mouvements de [PAN/TILT] ne sont pas limités.
[Ceiling] : L’appareil est fixé au plafond. Les
mouvements [TILT] sont limités à ±60°.
[Stage FL] : l’appareil est placé sur une scène, en
face du public. Le projecteur est toujours orienté vers
le public, c’est à dire face à la scène. Angle de
mouvement [PAN] (gauche-droite-gauche) : 160°.
Angle de mouvement [TILT] : 90° (60° au-dessus de
l’horizontale ; 30° sous l’horizontale.)
[Stage CE] : l’appareil est placé à l’envers, sur le plafond d’une scène. Le projecteur éclaire
principalement le public qui se trouve devant la scène. Angle de mouvement [PAN] (gauche-droite-
gauche) : 160°. Angle de mouvement [TILT] : 90° (verticalement, 75° vers l’avant, 15° vers l’arrière)
Une fois que le bon mode apparaît à l’écran, appuyez sur la touche [ENTER] pour confirmer.
Maintenez la touche [MODE] enfoncée pendant environ deux secondes pour mémoriser les réglages et
revenir en mode de fonctionnement normal.
Couleurs adjacentes
L’unité peut afficher les couleurs de base ou des couleurs adjacentes.
Appuyez sur la touche [MODE] et utilisez les touches ▼/▲ jusqu’à ce que [SplitCol] s’affiche à l’écran.
Appuyez sur la touche [ENTER] pour commencer l’édition.
Utilisez les touches ▼/▲ pour sélectionner « Oui » (couleurs adjacentes) ou « Non » (couleurs pleines
seulement).
Une fois que le bon mode apparaît à l’écran, appuyez sur la touche [ENTER] pour confirmer.
Maintenez la touche [MODE] enfoncée pendant environ deux secondes pour mémoriser les glages et
revenir en mode de fonctionnement normal.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77

Briteq BT-METEOR Le manuel du propriétaire

Catégorie
Projecteurs
Taper
Le manuel du propriétaire