Blaze King Chinook 30.2 Le manuel du propriétaire

Marque: Blaze King

Modèle: Chinook 30.2

Catégorie: Poêle à bois

Taper: Le manuel du propriétaire

180-CK30.2 v1.03 February 28, 2020

 e authority having jurisdiction (such a municipal building department,  re department, etc.) should be

consulted before installation to determine the need to obtain a permit.

Pour la version française de nos manuels S.V.P. vous référez à notre site web: www.blazeking.com

Manufactured By

Valley Comfort Systems Inc., 1290 Commercial Way, Penticton, BC, V2A 3H5, Canada

Phone: 250-493-7444  Fax: 250-493-5833  www.blazeking.com  info@blazeking.com

OPERATION & INSTALLATION MANUAL

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please SAVE THESE INSTRUCTIONS for future reference.

CHINOOK CK30.2

SOLID FUEL WOOD CATALYTIC STOVE

0142WS014E

0142WS014S

U.S. Environmental Protection Agency certi ed to comply with 2020 particulate emission standards using crib wood.

180-CK30.2 v1.03 February 28, 2020

Page 2

CK30.2

INTRODUCTION _____________________________________________________________ 4

SPECIFICATIONS _____________________________________________________________ 5

EMISSIONS __________________________________________________________________ 5

APPLIANCE DIMENSIONS ______________________________________________________ 6

CERTIFICATION LABEL ________________________________________________________ 7

SAFETY PRECAUTIONS ________________________________________________________ 8

INSTALLATION INSTRUCTIONS _________________________________________________ 11

PARTS INCLUDED .......................................................................................................................... 11

OPTIONAL EQUIPMENT ............................................................................................................... 11

FLOOR PROTECTION .................................................................................................................... 11

MINIMUM CLEARANCES ............................................................................................................. 12

COMBUSTION AIR ......................................................................................................................... 13

DRAFTING PERFORMANCE ......................................................................................................... 13

ROLE OF THE CHIMNEY ............................................................................................................... 13

VENTING SYSTEMS ...................................................................................................................... 14

RECOMMENDED FLUE HEIGHTS ................................................................................................ 17

MOBILE HOME (AND RESIDENTIAL ALCOVE INSTALLATIONS) ........................................... 18

OPTIONAL ACCESSORIES ............................................................................................................. 19

DOOR REMOVAL AND CHANGE-OUT ........................................................................................ 20

SIDE SHIELD REMOVAL AND CHANGE-OUT ........................................................................... 21

OPERATING INSTRUCTIONS ___________________________________________________ 22

INTRODUCTION ............................................................................................................................ 22

YOUR FIRST FIRE! .......................................................................................................................... 22

BYPASS ............................................................................................................................................ 22

CATALYTIC THERMOMETER ....................................................................................................... 22

THERMOSTAT ................................................................................................................................ 23

SELECTING WOOD ........................................................................................................................ 23

HOW TO USE MOISTURE METERS .............................................................................................. 24

EFFICIENCY .................................................................................................................................... 24

LIGHTING THE FIRE ..................................................................................................................... 25

RELOADING PROCEDURE (with the catalyst temperature in the ACTIVE ZONE) ....................... 26

RELOADING PROCEDURE (with the catalyst temperature still in the INACTIVE ZONE) ............. 26

FAN OPERATION .......................................................................................................................... 26

ICE - FORMATION AND PREVENTION ....................................................................................... 26

OPTIMAL THERMOSTAT SETTING ............................................................................................. 27

WOOD BURNING IN THE SHOULDER SEASON ......................................................................... 27

CATALYST MONITORING ______________________________________________________ 28

CATALYTIC COMBUSTOR, TESTING ........................................................................................... 28

CATALYTIC COMBUSTOR, CLEANING ....................................................................................... 28

CATALYTIC COMBUSTOR, TROUBLESHOOTING ...................................................................... 29

CATALYTIC COMBUSTOR, REPLACEMENT ............................................................................... 31

TABLE OF CONTENTS

180-CK30.2 v1.03 February 28, 2020

Page 3

CK30.2

MAINTENANCE ______________________________________________________________ 34

RUN-AWAY OR CHIMNEY FIRE .................................................................................................... 34

CHIMNEY MAINTENANCE ........................................................................................................... 35

ASH REMOVAL ............................................................................................................................... 35

LOADING DOOR GASKET INSPECTION...................................................................................... 36

LOADING DOOR GASKET REPLACEMENT................................................................................. 36

BYPASS DOOR GASKET INSPECTION .......................................................................................... 36

BYPASS DOOR GASKET REPLACEMENT ..................................................................................... 37

DOOR GLASS GASKET INSPECTION ........................................................................................... 38

DOOR GLASS GASKET REPLACEMENT ...................................................................................... 38

DOOR GLASS, CLEANING ............................................................................................................. 38

LOADING DOOR TENSION ADJUSTMENT ................................................................................. 39

OPTIONAL FAN ASSEMBLY .......................................................................................................... 40

CATALYTIC THERMOMETER ..................................................................................................... 40

THERMOSTAT ................................................................................................................................ 40

TROUBLESHOOTING __________________________________________________________ 41

REPLACEMENT PARTS ________________________________________________________ 44

WARRANTY _________________________________________________________________ 48

INSTALLER NOTES ____________________________________________________________ 52

TABLE OF CONTENTS

180-CK30.2 v1.03 February 28, 2020

Page 4

CK30.2

INTRODUCTION

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND IS PROHIBITED BY

FEDERAL AND STATE LAWS.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Before installing this appliance, contact the local building or ﬁ re authority and follow their guidelines.

• This appliance must be installed by a qualiﬁ ed installer.

• Risk of burns. The appliance should be turned oﬀ and cooled before servicing.

• Do not operate without fully assembling all components.

• Do not let the appliance become hot enough for any part to glow red.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may be sharp.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing

ignition.

• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and

others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house.

To restrict access to an appliance or appliance, install an adjustable safety gate to keep toddlers, young children and other at risk

individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance. Objects placed in front of the appliance must be

kept a minimum of 48” away from the front face of the appliance.

• Due to high temperatures, the appliance should be located out of traﬃ c and away from furniture and draperies.

• Ensure you have incorporated adequate safety measure to protect infants / toddlers from touching hot surfaces.

• Even after the appliance is out, all surfaces, including the glass and/or any attachment will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety hearth guards to protect children from hot surfaces. These guards must be

fastened to a wall and/or to the ﬂ oor.

• Any safety guard removed for servicing must be replaced prior to operating the appliance.

• Under no circumstances should this appliance be modiﬁ ed.

• This appliance must not be connected to a chimney ﬂ ue pipe servicing a separate solid fuel burning appliance.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done by a licensed

or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Operate only with the doors tightly closed.

• Appliance will over-ﬁ re if door is not shut and latched.

• Only certiﬁ ed doors / optional fronts / and surrounds for inserts with the unit are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags, these are

not toys and should be kept away from children and infants.

• If the appliance is not properly installed, a house ﬁ re may result. Do not expose the appliance to the elements (rain, etc.) and keep the

appliance dry at all times.

• The chimney must be sound and free of cracks and obstructions. Clean your chimney regularly as required.

• Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter ﬂ uid, or similar liquids to start or ‘freshen up’ a ﬁ re in this

heater. Keep all such liquids well away from the heater while it is in use.

• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to smoke spillage in your

home.

• Higher eﬃ ciencies and lower emissions will generally result when burning air dried seasoned woods, as compared to wet, green or

freshly cut wood. Burning wet unseasoned wood can cause excessive creosote accumulation. When ignited it can cause a chimney

ﬁ re that may result in a serious house ﬁ re.

• The appliance is designed to burn seasoned wood only. Do not burn treated wood, coal, charcoal, colored paper, cardboard, solvents

or garbage.

• Burn wood directly on the ﬁ rebricks. Do not use a grate or elevate the ﬁ re.

• Do not store wood within appliance installation clearances or within the space required for re-fueling and ash removal.

• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well away from the home or

structure until completely cool.

CALIFORNIA PROPOSITION 65

WARNING: This product can expose you to chemicals including

benzene, which is known to the State of California to cause cancer and birth

defects or other reproductive harm. For more information:

www.P65Warnings.ca.gov

180-CK30.2 v1.03 February 28, 2020

Page 5

CK30.2

SPECIFICATIONS

This unit was tested and listed UL 1482-11(R2015) and

ULC-S627-00 by OMNI-Test Laboratories.

This manual describes the installation and operation of the Ashford

AF30.2 catalytic equipped wood heater.

This heater is certiﬁ ed to comply with the 2020 U.S. Environmental

Protection Agency’s particulate emission standards using crib wood.

Under speciﬁ c test conditions this heater has been shown to deliver

heat at rates ranging from 11553 to 27116 Btu/hr.

This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating

instructions in this manual.

This wood heater contains a catalytic combustor, which needs periodic inspection and replacement for proper

operation. It is against federal regulations to operate this wood heater in a manner inconsistent with operating

instructions in this manual, or if the catalytic element is deactivated or removed.

The combustor supplied with this heater is a Z0336A-M or Z0334 metal combustor. Consult the catalytic

combustor warranty also supplied with this wood heater. Warranty claims should be addressed to:

in Canada in USA

Blaze King Industries / Valley Comfort Systems

Warranty Department, 1290 Commercial Way

Penticton, BC Canada V2A 3H5, Ph: 250-493-7444

Blaze King Industries

Warranty Department, 146A Street

Walla, Walla, Washington 99362, Ph: 509-522-2730

Model Chinook 30.2 (catalytic)

Height 35 1/2” (902 mm)

Width 29 1/4” (743 mm) (without removable bypass handle)

Depth 27 7/8” (708 mm) (without optional fan kit)

28 1/2” (724 mm) (with optional fan kit)

Flue collar 6” I.D.

Fire door opening 18 5/8” x 9 7/8” (473 mm x 251 mm)

Firebox depth 18” (457 mm) brick to brick, 20 1/2” (521 mm) brick to glass

Firebox width 20” (508 mm)

Firebox height 12 7/8” (327 mm)

Fire box capacity 2.9 cu. ft.

Recommended Fuel length 18” (457 mm) max.

Wood capacity (approximate): White oak - 60 lbs. (27.2 kg)

Fir - 40 lbs. (18.1 kg)

Construction 10 gauge & 1/4” ﬁ rebox, brick lined

18 gauge outer shields

Shipping Weight 425 lbs. (192.7 kg)

Chimney recommendation (Minimum) 15’ from stove top to chimney cap: Insulated liner recommended

EMISSIONS CO Average(%) g/hr

Low Burn 0.03 0.25

Med-low Burn 0.19 0.28

Med-high Burn 0.21 0.71

High Burn 0.19 3.23

EPA emission rate weighted average .80 g/hr

180-CK30.2 v1.03 February 28, 2020

Page 6

CK30.2

APPLIANCE DIMENSIONS













































































ZRSWLRQDOIDQ



























180-CK30.2 v1.03 February 28, 2020

Page 7

CK30.2

CERTIFICATION LABEL

MINIMUM CLEARANCES TO COMBUSTIBLES (See owners manual for complete description of all requirements)

DÉGAGEMENTS MINIMUM AUX COMBUSTIBLES (voir les directives d’installation pour la description complète de toutes les conditions)

Residential Installations

ABCDEFJ

Roof exit, parallel and corner.

Sortie de toit, parallèle et coin.

9.5”

241 mm

6.0”

153 mm

24.125”

603 mm

16.375”*

416 mm

4”

102 mm

17.625”*

448 mm

37”

940 mm

Wall exit, parallel and corner.

Sortie de mur, parallèle et coin.

9.5”

241 mm

6.0”

153 mm

24.125”

603 mm

16.375”*

416 mm

4”

102 mm

17.625”*

448 mm

37”*

940 mm

Alcove roof exit. Fan kit or rear shield required.

Sortie de toit en alcôve. Kit de ventilateur et protection arrière requise.

9.5”

241 mm

6.0”

153 mm

24.125”

603 mm

16.375”*

416 mm

37”

940 mm

Mobile Home Installations

Roof exit, parallel and corner. Fan kit or rear shield required. Outside air kit required.

La sortie du toit, parallèle et en coin. Kit de ventilateur et protection arrière requise. Kit d’air

extérieur requis.

9.5”

241 mm

6.0”

153 mm

24.125”

603 mm

16.375”*

416 mm

4”

102 mm

17.625”*

448 mm

37”

940 mm

*Check with local codes and pipe manufacturers for pipe clearances. In Canada 18” clearances from single wall pipe is required.

* Vériﬁ er avec le code du bâtiment local et avec le manufacturier de tuyaux pour les dégagements. Au Canada un dégagement de 18 po est exigé pour un tuyau à simple paroi.

Floor protection may be any non-combustible material or Listed Floor Protector, and must extend at least 18” (456 mm) in Canada or 16” (406 mm) in U.S.A., in front of the loading

door opening: In USA minimum size is 35" x 42 1/8” (889 mm x 1070 mm).

In Canada, minimum size is 45 1/4" x 52 1/8" (1150 mm x 1324 mm)

US ENVIRONMENTAL PROTECTION AGENCY Certiﬁ ed to comply with 2020 particulate emission standards using crib wood. (EPA test methods 28R/5G with an emission-rate of .80g/

hr). This wood heater needs periodic inspection and repair for proper operation. Consult the owner’s manual for further information. It is against federal regulations to operate this

wood heater in a manner inconsistent with operating instructions in the owner’s manual, or if the catalytic element is deactivated or removed.

*ONLY OPERATE WITH DOORS CLOSED. Open door to feed ﬁ re ONLY. *DO NOT OBSTRUCT COMBUSTION AIR OPENINGS. Do not obstruct the space beneath the heater. For Use

With Solid Wood Fuel Only - Do not burn other fuels, this may make the catalyst in the combustor inactive. The performance of the catalytic device or its durability has not been

evaluated as part of the certiﬁ cation. Combustor part number: 115-0336-A-M or 115-0556. Provide adequate outside air for combustion. *Replace with only ceramic glass, 5 mm.

Thickness.

BLAZE KING CATALYST STOVE - POÊLE À BOIS CATALYTIQUE

ROOM HEATER, SOLID FUEL TYPE, ALSO FOR USE IN MOBILE HOMES. / APPAREIL APPROUVÉ DE TYPE CARBURANT SOLIDE,

AUSSI ADAPTÉ POUR INSTALLER DANS UNE MAISON MOBILE.

SUITABLE FOR MOBILE-HOME INSTALLATION / CONCU POUR MAISONS MOBILES.

MODEL / MODÈLE: CK30.2

Tested to / Testé: UL 1482-11(R2015) / ULC S627-00

CERTIFIED IN BOTH UNITED STATES AND CANADA / CERTIFIÉ POUR LES ÉTATS-UNIS ET LE CANADA

MANUFACTURE DATE

JAN  FEB  MAR  APR  MAY  JUN 

JUL  AUG  SEP  OCT  NOV  DEC 

2019  2020  2021  2022  2023  2024 

La protection de plancher peut être de n’importe quel matériel non combustible ou Protecteur de plancher approuvé, et doit se prolonger au moins de 18” (456 mm) au Canada ou

16" (406 mm) aux États-Unis devant la porte de chargement: Aux États-Unis, la taille minimum est de 35" x 42 1/8” (889 mm x 1070 mm)

Au Canada la taille minimum est de 45 1/4" x 52 1/8" (1150 mm x 1324 mm)

L’AGENCE DE PROTECTION ENVIRONNEMENTALE DES U.S. - Certiﬁ é conformément aux normes d'émission de particules 2020 , en utilisant du bois machiné (méthodes d'essai

EPA 28R / 5G, ASTM E2515 et ASTM E2780, avec un taux d'émission de 0.80 g /hre). Cet appareil de chauﬀ age au bois nécessite des inspections périodiques et des réparations pour

un fonctionnement adéquat. Consulter le manuel du propriétaire pour plus d’informations. Il est contre les règlements fédéraux de faire fonctionner cet appareil de chauﬀ age à

l’encontre des instructions d’utilisation fournies dans le manuel du propriétaire, ou si l’élément catalytique est enlevé ou désactivé.

*Utiliser le uniquement avec les portes fermées. Ouvrir la porte pour alimenter le feu SEULEMENT. *Ne pas obstruer l’entrée d’air de combustion. Fournir l'apport d’air extérieur

adéquat pour alimenter la combustion. Ne pas obstruer l’espace sous l'appareil. Utiliser uniquement avec des combustibles solides - ne pas brûler aucun autre combustible, ce

qui peut rendre le catalyseur de la chambre à combustion inactif. La performance du catalyseur ou sa longévité n’a pas été évaluée dans le cadre de la certiﬁ cation. Numéro du

catalyseur: 115-0336-A-M ou 115-0556. *Employer seulement le verre en céramique d’une épaisseur de 5mm si le remplacement est nécessaire.

PREVENT HOUSE FIRES- Install and use only in accordance with Blaze King’s installation and operation instructions. Contact local building or ﬁ re oﬃ cials about restrictions and

installation inspection in your area. The ﬂ ue size is 6".

CHIMNEYS: DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. Except for installation detailed below, use 6” listed factory built chimney suitable

for use with solid fuels and conforming to, ULC629 in Canada or UL-103HT in the USA or a masonry residential type chimney.

Mobile home, residential close clearance, and residential alcove installations require a 6” listed double wall close clearance chimney connector, with matching listed factory built

chimney suitable for use with solid fuels and conforming to, ULC629 in Canada or UL-103HT in the USA. Mobile Home installations are only allowed with a roof exit.

Do not install in a sleeping room. Passing through a wall or ceiling requires special methods: see instructions and local building codes.

MANUFACTURED IN

 USA:

Blaze King Industries

146A Street

Walla Walla, WA.

99362

 CANADA:

Valley Comfort Systems

1290 Commercial Way

Penticton, B.C.

V2A 3H5

SN - 20.

CHINOOK CK30.2

170-0233 [02 19]

G - 3” (77 mm) in U.S.A.

8” (203 mm) in Canada

H - 16” (406 mm) in U.S.A.

18” (456 mm) in Canada

I - 0” (0 mm) in U.S.A.

8” (203 mm) in Canada

K - 18” (456 mm) *

ALCOVE

min. width / min. largeur

max. depth / max. profondeur

min. height above stove / hauteur min.

au-dessus du poêle

48”

37”

POUR PRÉVENIR UN INCENDIE - Installer et employer seulement selon le manuel d’installation de Blaze King. Contacter les autorités locales en bâtiments ou en matière de

prévention d'incendies au sujet des normes d'inspection et d'installation dans votre secteur. La dimension des conduits de cheminée est de 6”.

CHEMINÉE: NE PAS CONNECTER CETTE UNITÉ A UNE CONDUITE DE CHEMINÉE SERVANT UN AUTRE APPAREIL. Excepté pour les situations détaillées ci-dessous, employer

une cheminée de 6” homologuée par le fabricant à des ﬁ ns d'utilisation pour combustibles solides conformément à la norme ULC629 au Canada ou UL-103HT aux Etats-Unis ou

employer une cheminée en maçonnerie de type résidentiel.

L'installation dans une maison mobile, en espace restreint ou dans des endroits à faible dégagement, requiert l'utilisation de connecteurs muraux à doubles parois et ayant une

épaisseur 6” pour la cheminée. Ceux-ci doivent être homologués par le fabricant à des ﬁ ns d'utilisation pour combustibles solides conformément à la norme ULC629 au Canada ou

UL-103HT aux Etats-Unis. L'installation dans une maison mobile est permise seulement avec une sortie passant par le toit. Ne pas installer dans une chambre à coucher. Passer à

travers un mur ou un plafond requiert une méthode spéciﬁ que décrite dans les instructions et dans le code local du bâtiment.

0142WS014E

0142WS014S

180-CK30.2 v1.03 February 28, 2020

Page 8

CK30.2

This appliance must be connected to a listed high temperature (ULC629 IN CANADA OR

UL-103HT IN THE USA) residential type factory built solid fuel chimney or an approved

masonry chimney with a ﬂ ue liner.

Chimney and chimney connector must be in good condition and kept clean.

NEVER vent the stove to other rooms of the building. Must be vented to the outside ONLY.

NEVER use a chimney or chimney connector smaller then the stove exhaust, unless

approved by your local inspector.

NEVER vent the stove into a “Class B” gas vent chimney.

DO NOT CONNECT IN CONJUNCTION WITH ANY AIR DISTRIBUTION DUCTWORK

UNLESS SPECIFICALLY APPROVED FOR SUCH INSTALLATIONS.

Inspect the chimney connector and chimney regularly during each burning season and

clean when necessary.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

NEVER intentionally start a chimney ﬁ re to clean the ﬂ ue.

When installed in a mobile home, this appliance must be bolted to the ﬂ oor and provided

with outside air.

WARNING: DO NOT INSTALL IN A SLEEPING ROOM

CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME

FLOOR, WALL, AND CEILING/ROOF MUST BE MAINTAINED.

Check with local building oﬃ cials.

If the Optional Fan Kit is

installed, connect this unit to

a properly grounded, 110-volt

electrical outlet. Do not route

the power cord in front of or

under the appliance.

Do not make any changes or

modiﬁ cations to an existing

masonry ﬁ replace or chimney

to install this appliance. Do

not make any changes to

the appliance to increase

combustion air.

SAFETY PRECAUTIONS

IF THIS BLAZE KING APPLIANCE IS NOT PROPERLY INSTALLED OR OPERATED, A HOUSE FIRE MAY

RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. CONTACT LOCAL

BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION

REQUIREMENTS IN YOUR AREA.

PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW APPLIANCE. FAILURE TO

FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH.

180-CK30.2 v1.03 February 28, 2020

Page 9

CK30.2

Never try to repair or replace

any part of this appliance

unless instructions are given

in this manual. All other work

must be done by a trained

technician.

Allow the appliance to cool

down before carrying out any

maintenance or cleaning.

Maintain the door and glass

seal and keep them in good

condition. A leaking door seal

will shorten burn times and

may harm the combustor.

Avoid placing wood against

the glass when loading. Do

not slam the door or strike the

glass.

Do not throw this manual

away. This manual has

important operating and

maintenance instructions that

you will need at a later time.

Always follow the instructions

in this manual.

Do not place clothing or other

ﬂ ammable items on or near

this appliance.

Do not use a grate or other

device to elevate the ﬁ re oﬀ of

the ﬁ rebox ﬂ oor. Burn the ﬁ re

directly on the bricks.

Ashes should be placed in a

steel container with a tightly

ﬁ tting lid and moved outdoors

immediately. If the ashes are

disposed of by burial in soil or

otherwise locally dispersed,

they should be retained in

the closed container until

all cinders have thoroughly

cooled. Other waste shall not

be placed in this container.

SAFETY PRECAUTIONS

It is required in some jurisdictions to install smoke and carbon monoxide detectors where

heaters are installed. Install at least one smoke detector on each ﬂ oor of your home to

ensure your safety. It should be located away from the wood appliance and close to the

sleeping areas. Locating a smoke detector too close to a wood appliance can cause the

smoke detector alarm to sound if a puﬀ of smoke is emitted while the wood appliance door

is open during reloading. Follow the smoke detector manufacturers placement, installation,

and maintenance instructions.

DO NOT OVER FIRE THIS

HEATER. Attempts to

achieve heat output rates

that exceed heater design

speciﬁ cations can result in

permanent damage to the

heater and to the catalytic

combustor. Over ﬁ ring the

appliance may cause a house

ﬁ re. Never burn the appliance

so hot that the appliance or

chimney connector begins to

glow.

180-CK30.2 v1.03 February 28, 2020

Page 10

CK30.2

36”

Never burn the appliance

with the loading door open.

Leaving the door cracked

open may damage the

combustor.

Never block free airﬂ ow

through vents on this

appliance.

HOT WHILE IN OPERATION.

KEEP CHILDREN,

CLOTHING AND FURNITURE

AWAY.

CONTACT MAY CAUSE SKIN

BURNS.

Do not touch the appliance

when it is hot and educate all

children of the danger of a

high temperature appliance.

Young children should be

supervised when they are

in the same room as the

appliance.

This appliance must be

properly installed to prevent

the possibility of a house

ﬁ re. The instructions must

be strictly adhered to. Do not

use makeshift methods or

compromise in the installation.

Do not use chemicals or ﬂ uids

to start the ﬁ re. Never use

gasoline, gasoline-type lantern

fuel, kerosene, charcoal lighter

ﬂ uid, or similar liquids to start or

‘freshen up’ a ﬁ re in this heater.

Keep all such liquids well away

from the heater while it is in use.

Some fuels could generate

carbon monoxide and are very

dangerous.

Keep furniture, curtains,

wood, paper and other

combustibles a minimum of

36in (914mm) away from

the front of the appliance.

ALSO, DO NOT STORE

COMBUSTIBLES UNDER

THE APPLIANCE (WOOD,

PAPER etc.).

Contact local building oﬃ cials

to obtain a permit and

information on any installation

restriction or inspection

requirements in your area.

Notify your insurance

company as well.

SAFETY PRECAUTIONS

This appliance is designed and approved for burning cord wood only. DO NOT burn trash,

garbage; artiﬁ cial or paper logs; gift wrappings; coal; lighter ﬂ uids; chemical cleaners;

chemical starters; treated or painted wood; salt water driftwood or foil-backed paper such

as gum wrappers or cigarette packages; lawn clippings or yard waste; materials containing

rubber (including tires), plastic, asbestos; waste petroleum products, paints or paint

thinners, or asphalt products; construction or demolition debris; railroad ties or pressure-

treated wood; manure or animal remains; unseasoned wood or paper products, cardboard,

plywood, or particleboard. The prohibition against burning these materials does not prohibit

the use of ﬁ re starters made from paper, cardboard, saw dust, wax and similar substances

for the purpose of starting a ﬁ re in an aﬀ ected wood heater. Burning these materials may

result in the release of toxic fumes or render the heater ineﬀ ective and cause smoke.

Burn natural wood only. It will void all warranties and safety listings and may damage the

combustor.

180-CK30.2 v1.03 February 28, 2020

Page 11

CK30.2

INSTALLATION INSTRUCTIONS

FLOOR PROTECTION

If the stove sits on a combustible ﬂ oor, a non-combustible shield must be used underneath the

stove and extending 16” out from the front and 8” on either side of the fuel-loading door in the

USA. In Canada a non-combustible shield must be used underneath the stove and extending 8”

on either side and rear and 18” out in front of the loading door.

A non-combustible shield is also required underneath the chimney connector and extending at

least 2” (50.8mm) on either side of the chimney connector.

See the next page for minimum sizes depending on model. This ﬂ oor protection is required

to prevent sparks from falling onto the combustible ﬂ oor. See CSA B365-M87). This product

does not require thermal hearth pad protection.

• BEFORE INSTALLING THIS APPLIANCE, CONTACT THE LOCAL BUILDING OR FIRE OR OTHER

AUTHORITY HAVING JURISDICTION AND FOLLOW THEIR GUIDELINES.

• THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. FOLLOW THE

INSTALLATION DIRECTIONS. DO NOT OPERATE WITHOUT FULLY ASSEMBLING ALL

COMPONENTS.

• IF THIS APPLIANCE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT.

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF

CONTACTED. CHILDREN AND PETS MUST BE KEPT FROM TOUCHING THE APPLIANCE

WHEN IT IS HOT.

• COMBUSTIBLE MATERIAL SUCH AS FIRE WOOD, WET CLOTHING, ETC. PLACED TOO CLOSE

CAN CATCH FIRE. OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A

MINIMUM OF 48”(1219 MM) FROM THE FRONT OF THE APPLIANCE.

Blaze King grants no warranty, implied or

stated, for the installation or maintenance of the

appliance and assumes no responsibility of any

consequential damage(s).

PARTS INCLUDED

1. Poker

2. Manual Kit (w/ warranty cards, thermometer, bypass handle, ﬂ ue ring)

OPTIONAL EQUIPMENT

1. Fan Kit (Z1714) 2. Rear shield (Z4015)

180-CK30.2 v1.03 February 28, 2020

Page 12

CK30.2

INSTALLATION INSTRUCTIONS

MINIMUM CLEARANCES

Residential Installations A B C D E F J

Roof exit, parallel and corner.

9.5”

241 mm

6”

153 mm

24.125”

603 mm

16.375”*

416 mm

4”

102 mm

17.625”*

448 mm

37”

940 mm

Wall exit, parallel and corner.

9.5”

241 mm

6”

153 mm

24.125”

603 mm

16.375”*

416 mm

4”

102 mm

17.625”*

448 mm

37”*

940 mm

Alcove, roof exit. Fan kit or rear shield required.

9.5”

241 mm

6”

153 mm

24.125”

603 mm

16.375”*

416 mm

37”

940 mm

Mobile Home Installation

Roof exit, parallel and corner. Fan kit or rear shield required. Outside air kit

required.

9.5”

241 mm

6”

153 mm

24.125”

603 mm

16.375”*

416 mm

4”

102 mm

17.625”*

448 mm

37”

940 mm

* Check with local codes and pipe manufacturer for pipe clearances. In Canada, 18” clearances from single wall pipe is required.

Clearances may only be reduced by means approved by the regulatory authority

G = 3” (77mm) in USA

8” (203mm) in Canada

H = 16” (406mm) in USA

18” (456mm) in Canada

I = 0” (0mm) in USA

8” (203mm) in Canada

K = 18” (456mm) for single wall pipe in Canada

Ember protection shield (not required to have an insulation value) or

a listed UL 1618 Type 1 ﬂ oor protector must have a minimum size of:

In USA: 35 x 42 1/8” (889 mm x 1070 mm)

In Canada: 45 1/4” x 52 1/8” (1150 mm x 1324 mm)

Min. Alcove minimum width 48”, maximum depth 48”, minimum height above stove top 37”

This stove must be installed in compliance with all local codes and regulations.



(

)

 





LQ&DQDGDDQG





LQ86$

 





LQ&DQDGDDQG





LQ86$



PP

0,1IW

IWUHFRPHQGHG

180-CK30.2 v1.03 February 28, 2020

Page 13

CK30.2

INSTALLATION INSTRUCTIONS

COMBUSTION AIR

Ensure adequate combustion air allowing for all other exhausting type appliances in the dwelling (range hoods,

dryers, etc.). In air tight homes and modern constructions, careful considerations must be taken into account

when using a wood burning appliance. Heat recovery ventilators (HRV) systems along with constant running

fan motors in air handlers must be taken into account when balancing the system. Failure to do so may

result in air starvation, smoke spillage and carbon monoxide threats. Consult a HVAC specialist for proper

installation. Ensure adequate combustion air allowing for all other exhausting type appliances in the dwelling

(range hoods, dryers, etc.). In airtight houses it is recommended to install a fresh air inlet into the room where

the appliance is located, to prevent air starvation.

ROLE OF THE CHIMNEY

Without a proper installed chimney, this appliance will not burn correctly.

The role of the chimney is to pull the proper amount of air into the ﬁ rebox for the purpose of complete

combustion. Incomplete combustion will lead to more smoke and pollution of the outside air. A proper

operating chimney will allow the user to enjoy peak performance at all burn operating levels from low to high.

Blaze King therefore recommends vertical installations with a minimum length of 15’ from stove top to chimney

cap. In all freestanding stove installations, use double wall stove pipe from the stove top to the ceiling support

box. The use of double wall stove pipe does allow for reduced clearances, however most importantly, it helps

to keep the chimney warm and improve draft.

For wall exits, the same suggestion applies. With the addition of the recommendation to use two 45 degree

elbows rather than a single 90 degree elbow. The use of two 45 degree elbows will allow for both a smoother

transition to the exterior chimney and will also shorten the horizontal run to the outside chimney. A minimum

36” rise is recommended prior to any elbows being used. When possible, outside chimney systems should

be isolated from direct exposure to winter weather by building a chase around the chimney, observing all

clearances as speciﬁ ed by the venting manufacturer. Doing so will help to keep the chimney warmer and

improve draft. (see RECOMMENDED FLUE HEIGHTS)

DRAFTING PERFORMANCE

Draft is the force which moves air into the appliance up through the chimney. The amount of draft created by

your chimney depends upon length, oﬀ sets, insulating properties, obstructions (such as architectural design,

trees), local geography and other factors.

External forces, such as outdoor temperature, wind, barometric pressure, topography, or factors inside the

home (negative pressure from exhaust fans, chimneys, air inﬁ ltration, etc) may adversely aﬀ ect draft.

Too much draft may cause excessive temperatures in the appliance and may damage the heater. An

uncontrollable burn or excessive temperature indicates excessive draft.

Inadequate draft may cause back puﬃ ng (spillage) into the room and plugging of the chimney, chimney cap or

spark arrestor screen. Inadequate draft may cause smoke to leak into the room through appliance or chimney

connector joints. Poor draft can also lead to poor heat production and the inability for the combustor to remain

active in lower burn rate settings.

High eﬃ ciency appliances, such as your Blaze King stove, may require some ﬁ ne tuning of your chimney

system in order to maximize performance.

Blaze King cannot be responsible for external forces leading to less than optimal performance.

180-CK30.2 v1.03 February 28, 2020

Page 14

CK30.2

VENTING SYSTEMS

The venting system consists of a chimney connector and a chimney. These get extremely hot during use.

Temperatures inside the chimney may exceed 2000 degrees in the event of a creosote ﬁ re. To protect against

the possibility of a house ﬁ re, the chimney connector and chimney must be properly installed and maintained.

A listed thimble must be used when a connection is made through a combustible wall to a chimney. A chimney

support package must be used when a connection is made through the ceiling to a listed prefabricated

chimney. These accessories are absolutely necessary to provide safe clearances to combustible wall and

ceiling material.

This stove may be connected to a lined masonry chimney or a listed factory built chimney suitable for use with

solid fuels and conforming to, ULC629 in Canada or UL-103HT in the USA. Do not connect it to a chimney

serving another appliance. To do so will aﬀ ect the safe operation of both appliances, and will void the stove

warranty. You must comply with the local authority having jurisdiction and/or in Canada, CSA installation

standard B365-M87.

The chimney connector must be 6” diameter, 24 MSG Black/Blue steel. Do not use aluminum or galvanized

steel. They cannot properly withstand the extreme temperatures of a wood ﬁ re. The chimney connector

between the stove and the chimney should be as short and direct as possible.

The chimney connector must be attached to either an approved masonry chimney or one of the listed factory

built chimneys suitable for use with solid wood fuel. All joints must be tight and fastened with sheet metal

screws.

THE CHIMNEY CONNECTOR IS TO BE USED ONLY WITHIN THE ROOM, BETWEEN THE STOVE

AND CEILING / WALL. NEVER USE A CHIMNEY CONNECTOR TO PASS THROUGH AN ATTIC

OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED SPACE, OR A FLOOR, OR CEILING. AN

EFFECTIVE VAPOR BARRIER MUST BE MAINTAINED AT THE LOCATION WHERE THE CHIMNEY

OR COMPONENT PENETRATES TO THE EXTERIOR OF THE STRUCTURE. ALWAYS MAINTAIN

THE MINIMUM CLEARANCES TO COMBUSTIBLES AS REQUIRED BY THE APPLICABLE BUILDING

CODES.

INSTALLATION INSTRUCTIONS

180-CK30.2 v1.03 February 28, 2020

Page 15

CK30.2

INSTALLATION INSTRUCTIONS

CONNECTION TO A METAL PREFABRICATED CHIMNEY

Refer to “RECOMMENDED FLUE HEIGHTS” chart for minimum ﬂ ue height recommendations and ULC629

in Canada or UL-103HT in the USA for installation codes. When a metal prefabricated chimney is used, the

manufacturer’s installation instructions must be followed precisely. You must also purchase (from the same

manufacturer) and install the ceiling support package or wall pass through and “T” section package, ﬁ re

stops (when needed), insulation shield, roof ﬂ ashing, chimney cap, etc. Maintain the proper clearance to the

structure as recommended by the manufacturer. This clearance is usually a minimum of 2 inches, although it

may vary by manufacturer or for certain components.

There are basically two methods of metal chimney installation. One method is to install the chimney inside

the residence through the ceiling(s) and the roof. The other method is to install an exterior chimney that runs

up the outside of the residence (not recommended). If it is necessary to run the chimney outside, build an

outside chase around the chimney.

The chimney must be the required height above the

roof or other obstruction for safety and for proper draft

operation. The requirement is that the chimney must

be at least 3 feet higher than the highest point where it

passes through the roof and at least 2 feet higher than

the highest part of the roof or structure that is within 10

feet of the chimney, measured horizontally (Fig. 1). The

height requirement is necessary in the interest of safety

and does not necessarily assure proper ﬂ ue draft. Use

a minimum total system height of 15 feet, measured

from the stove ﬂ ue collar to the top of the chimney, not

including the chimney cap.

STANDARD HORIZONTAL INSTALLATION

STANDARD VERTICAL INSTALLATION

3 ft. (.91 m)

recommended

180-CK30.2 v1.03 February 28, 2020

Page 16

CK30.2

INSTALLATION INSTRUCTIONS

CONNECTION TO A MASONRY CHIMNEY

Masonry chimney***

Ensure that a masonry chimney meets the minimum standards

(NFPA) by having it inspected by a professional. Make sure there

are no cracks, loose mortar or other signs of deterioration and

blockage. Have the chimney cleaned before the stove is installed

and operated. When connecting the stove through a combustible

wall to a masonry chimney, special methods are needed.

In Canada, the wall cut away is to provide 18” clearance for the

connector. The resulting space must remain empty. A ﬂ ush

mounted sheet metal cover may be used on one side only. If

covers are to be used on both sides, each cover must be mounted

on noncombustible spacers at least 1” clear of the wall.

***Blaze King recommends the use of a Stainless steel liner,

preferably insulated, inside a masonry chimney. This is to

maintain proper draft and overall better operation of the unit.

Your local dealer or local jurisdiction can provide details of

approved methods of passing a chimney connector through a

combustible wall in your area. In USA, the National Fire

Protection Association has minimum standards to comply

with. In Canada , this type of installation must conform to

CAN/CSA-B365, Installation Code for Solid Fuel Burning

Appliances and Equipment.

180-CK30.2 v1.03 February 28, 2020

Page 17

CK30.2

INSTALLATION INSTRUCTIONS

RECOMMENDED FLUE HEIGHTS

1. At sea level the minimum height is a 15 ft (4.6 m) straight run.

2. Add the following vertical height to the ﬂ ue to compensate for:

45° elbow = 1.0 ft (.30 m)

90° elbow = 2.0 ft (.61 m)

“T” section= 3.0 ft (.91 m)

3. Each foot of horizontal run = 2 ft (.61 m) of vertical rise.

Example: One 90° elbow = 2ft (.61 m)

2ft Horizontal run = 4ft (1.2 m)

One base “T” = 3ft (.91 m)

Total height addition = 9ft (2.7 m) at sea level

MINIMUM RECOMMENDED FLUE HEIGHT

ELEVATION

ABOVE SEA

LEVEL

NUMBER OF ELBOWS

0 2 X 15° 2 X 30° 2 X 45°

0 - 1000 ft

0 - 305 m

4.6 m

4.9 m

5.5 m

5.8 m

1000 - 2000 ft

305 - 610 m

15.5

4.7 m

16.5

5.0 m

18.5

5.6 m

19.5

5.9 m

2000 - 3000 ft

610 - 914 m

4.9 m

5.2 m

5.8 m

6.1 m

3000 - 4000 ft

914 - 1219 m

16.5

5.0 m

17.5

5.3 m

19.5

5.9 m

20.5

6.2 m

4000 - 5000 ft

1219 - 1524 m

5.2 m

5.5 m

6.1 m

6.4 m

5000 - 6000 ft

1524 - 1829 m

17.5

5.3 m

18.5

5.6 m

20.5

6.2 m

21.5

6.6 m

6000-7000 ft

1829 - 2134 m

5.5 m

5.8 m

6.4 m

6.7 m

7000 - 8000 ft

2134 - 2438 m

18.5

5.6 m

19.5

5.9 m

21.5

6.6 m

22.5

6.9 m

NOTE: No more than one oﬀ set (two elbows allowed).

Two 45°elbows equal one 90° elbow

Please note: These are only guidelines. Please refer to the section in the manual pertaining to draft. Every

installation is unique and can be inﬂ uenced by topographical and geographical phenomena.

The use of a manometer and an understanding of pressure planes and the stack eﬀ ect are imperative in

planning and executing a successful installation.

180-CK30.2 v1.03 February 28, 2020

Page 18

CK30.2

INSTALLATION INSTRUCTIONS

In mobile home installations, the stove must be securely fastened to the ﬂ oor using the tie-downs

provided in the Outside Air kit. To access the screw down hole, remove side shields (see “SIDESHIELD

REMOVAL AND CHANGE-OUT”.

ALSO, a #8 ground wire must be attached to the stove and an appropriate ground.

MOBILE HOME (AND RESIDENTIAL ALCOVE INSTALLATIONS)

Requires outside air kit, and either rear shield OR fan kit. (See next page for kits and part numbers).  e outside

air kit is easiest to mount before the stove is installed. See instructions packed with each kit.

NOTE: UNDER NO CIRCUMSTANCES SHOULD THE FRESH AIR TUBE EVER BE INSTALLED

HIGHER THAN THE BOTTOM OF THE APPLIANCE FIREBOX FLOOR.

When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed

precisely. You must also purchase (from the same manufacturer) and install the ceiling support package,  re

stops (when needed), insulation shield, roof  ashing, chimney cap, etc. Maintain the proper clearance to the

structure as recommended by the manufacturer.

 e Chimney connector must be a listed double wall close clearance type. Insulated chimney components must

be a listed factory built chimney suitable for use with solid fuels and conforming to ULC629 in Canada and

UL-103HT in the USA. Single wall stove pipe is not allowed in mobile homes or alcove installations. For mobile

home, the chimney needs to be removable to allow for transportation of the mobile home.

DO NOT INSTALL IN SLEEPING ROOM. THE STRUCTURAL INTEGRITY OF THE MOBILE

HOME FLOOR, WALL AND CEILING / ROOF MUST BE MAINTAINED.

180-CK30.2 v1.03 February 28, 2020

Page 19

CK30.2

INSTALLATION INSTRUCTIONS

OPTIONAL ACCESSORIES

Outside air kit, rear shield or fan kit are optional accessories, but are required for the following installations:

MOBILE HOME INSTALLATION — Requires outside air kit and fan kit or rear shield

RESIDENTIAL ALCOVE — Requires fan kit or rear shield

REAR SHIELD KIT (Z4015)

EITHER this rear shield OR the fan kit (P/N Z1714) is REQUIRED FOR:

MOBILE HOME, any installation

RESIDENTIAL ALCOVE

FAN KIT (P/N Z1714)

EITHER this fan kit or the rear shield (Z4015) is REQUIRED FOR:

MOBILE HOME, any installation

RESIDENTIAL ALCOVE

NOTE: Fan kit should be installed before the stove is placed into position

ELECTRICAL CONNECTION

Your Blaze King fan kit is equipped with a three-prong (grounded) plug to decrease shock hazard.

THIS PLUG SHOULD BE INSERTED DIRECTLY INTO A PROPERLY-GROUNDED, THREE-HOLE

RECEPTACLE. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THIS PLUG. Do not route

the power cord in front or under the stove.

OUTSIDE AIR KIT (P/N 1726B)

REQUIRED FOR: MOBILE HOME (any installation)

The outside air inlet hose is a ﬂ exible tube to bring outside air for combustion into the stove from outside

the residence, through the wall or up through the ﬂ oor. The ﬂ exible tube will allow some adjustment over

or around ﬂ oor joists or plumbing. DO NOT CHANGE THE STRUCTURAL INTEGRITY OF THE FLOOR.

This air hose must be kept open at all times to provide outside air for combustion.

INSTALLATION:

See instructions included with the outside air kit. Tools needed: 1/4" or 3/8" drill motor, saber saw, saber

saw wood & metal blades, 5/16" nut driver or wrench, 7/16" wrench, small tube of hi-heat silicone.

180-CK30.2 v1.03 February 28, 2020

Page 20

CK30.2

INSTALLATION INSTRUCTIONS

DOOR REMOVAL AND CHANGE-OUT

If the door needs to be removed or changed out, follow the steps below:

DOOR IS HEAVY AND FALLS OUT WHEN PIN BOLTS ARE PULLED OUT PLEASE HOLD

DOOR FIRMLY.

1. Insert a 1/4” Allen key into

the bolt head.

2. Secure the nut with a

9/16” wrench.

3. Turn the bolt counter-

clockwise to remove the

nut.

4. Repeat STEP 1-3 on other

hinge.

5. Holding the door securely,

pull out the bolts.

6. Pull the door away from

the stove.

La page charge ...

Blaze King Chinook 30.2 Le manuel du propriétaire

Marque: Blaze King

Modèle: Chinook 30.2

Catégorie: Poêle à bois

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Blaze King Chinook 30.2 Owner's manual

Blaze King Chinook 30.2 Le manuel du propriétaire

Blaze King Chinook 30.2 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents