AT&T TL88102 Manuel utilisateur

Marque: AT&T

Modèle: TL88102

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

TL88002

User’s manual

TL88002/TL88002BK

DECT 6.0 2-line

expansion handset

for use with AT&T models

TL88102/TL88102BK/TL88202

Congratulations

on your purchase of this AT&T product. Before using this AT&T

product, please read the Important safety information section on

pages 19-21 of this manual. For complete instructions, please refer

to the manual provided with your TL88102/TL88102BK/TL88202TL88102/TL88102BK/TL88202

telephone. You can also visit our website at

www.telephones.att.com or call 1 (800) 222-3111. In

Canada, dial 1 (866) 288-4268.

This telephone meets the California Energy Commission

regulations for energy consumption. Your telephone is set up to

comply with the energy–conserving standards right out of the box.

No further action is necessary.

Model number: TL88002/TL88002BK

Type: DECT 6.0 2-line expansion handset

Serial number: _______________________________________________

Purchase date: _______________________________________________

Place of purchase: _____________________________________________

Both the model and serial numbers of your AT&T product can be

found on the bottom of the charger.

Save your sales receipt and original packaging in case it is

necessary to return your telephone for warranty service.

Telephones identied with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Compatible with

Hearing Aid T-Coil

TIA-1083

Parts checklist

Your telephone package contains the following items. Save your

sales receipt and original packaging in the event warranty service

is necessary.

Battery for

cordless handset

Cordless handset

Charger for cordless

handset with power

adapter installed

Battery compartment

cover

User’s manual

Belt clip

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1349

User’s manual

TL88002/TL88002BK

DECT 6.0 2-line

expansion handset

for use with AT&T models

TL88102/TL88102BK/TL88202

User’s manual

TL88002/TL88002BK

DECT 6.0 2-line expansion handset

for use with AT&T models

TL88102/TL88102BK/TL88202

Table of contents

Getting started

Installation .......................................................................................................................... 1

Quick reference guide - handset .........................................................................2

Charger installation ......................................................................................................5

Battery installation and charging .......................................................................6

Registration and deregistration

Adding and registering handsets ........................................................................8

Deregistering handsets .............................................................................................9

Deregister all handsets from your telephone base ...........................9

Appendix

Troubleshooting........................................................................................................... 10

Maintenance ................................................................................................................... 18

Important safety information .............................................................................19

Safety information ..................................................................................................19

Especially about cordless telephones .......................................................20

Precautions for users of implanted cardiac pacemakers ............21

Pacemaker patients ...............................................................................................21

Especially about telephone answering systems.................................21

For C-UL compliance ................................................................................................. 22

Mesures de sécurité importantes ............................................................... 22

FCC Part 68 and ACTA ..............................................................................................26

FCC Part 15 .......................................................................................................................28

California Energy Commission battery charging testing

instructions ..................................................................................................................29

Limited warranty .........................................................................................................30

Technical specications .......................................................................................... 33

DECT 6.0 digital technology ............................................................................. 33

Telephone operating range ............................................................................. 33

Redening long range coverage and clarity ......................................... 33

See pages 6-7

for easy instructions.

You must install and

charge the battery before

using the telephone.

STOP!

Installation

Your product may be shipped with a protective sticker covering the

handset display - remove it before use.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

Avoid placing the telephone base too close to:

Communication devices such as television sets, VCRs, or other

cordless telephones.

Excessive heat sources.

Noise sources such as a window with trac outside, motors,

microwave ovens, refrigerators, or uorescent lighting.

Excessive dust sources such as a workshop or garage.

Excessive moisture.

Extremely low temperature.

Mechanical vibration or shock such as on top of a washing

machine or workbench.

•

Getting started

Quick reference guide - handset

Getting started

REDIAL/PAUSE

Press to review the redial list.

While dialing or entering numbers into the

directory, press and hold to insert a dialing

pause.

•

DIR/VOLUME

Press to enter the directory when the

telephone is not in use.

Press to scroll up while in menus.

During a call or message playback, press to

increase the listening volume.

While entering names or numbers, press to

move the cursor to the right.

•

LINE 1/FLASH

Press to make or answer a call on line 1.

During a call, press to answer an incoming

call on line 1 when you receive a call waiting

alert.

•

While reviewing a call log entry, press

repeatedly to add or remove 1 in front of the

telephone number before dialing or saving it

in the directory.

•

/SPEAKER

Press to make or join a call using the first

available line, starting with line 1.

Press to answer a call using the

speakerphone.

During a call, press to switch between

speakerphone and handset use.

•

CHARGE light

On when the handset is charging in the

telephone base or charger.

•

Quick reference guide - handset

Getting started

CID/VOLUME

Press to review the call log when the

telephone is not in use.

Press to scroll down while in menus.

During a call or message playback, press to

decrease the listening volume.

While entering names or numbers, press to

move the cursor to the left.

•

OFF/CANCEL

During a call, press to hang up.

Press and hold while the telephone is not in

use to erase the missed calls indicator.

Press to delete a digit or character while

entering a number or name.

While in a menu, press to cancel an

operation, back up to the previous menu, or

exit the menu display; or press and hold to

return to the idle mode.

•

Soft keys (2)

Press to select a menu item displayed above

the key.

•

LINE 2/FLASH

Press to make or answer a call on line 2.

During a call, press to answer an incoming

call on line 2 when you receive a call waiting

alert.

•

# (pound key)

Press repeatedly to show other dialing

options when reviewing a call log entry.

•

INT

Press to initiate an intercom conversation or

transfer a call.

•

HOLD

Press to put a call on hold.•

Quick reference guide - handset

Getting started

Main menu

ANSWERING SYS

DIRECTORY

CALL LOG

RINGERS

SETTINGS

•

Using menus:

Press the MENU soft key to show the menu.

Press qCID or pDIR to scroll through menu items.

Press the SELECT soft key to confirm or save changes to a

highlighted menu item.

Press the BACK soft key or OFF/CANCEL to cancel an

operation, back to the previous menu without making any

changes, or exit the menu display.

For complete instructions, refer to the user’s manual provided with

your TL88102/TL88102BK/TL88202 telephone system.TL88102/TL88102BK/TL88202 telephone system. telephone system.

If you are unable to nd your user’s manual, go to

www.telephones.att.com/manuals to read and/or

download the manual.

•

Main menu

HANDSET

12:45am 12/31

IMPORTANT INFORMATION

Use only the power adapter supplied with this product. To order a replacement

power adapter, visit our website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

The power adapter is intended to be correctly oriented in a vertical or oor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

•

Plug the power adapter into a

power outlet not controlled by a

wall switch.

Charger installation

Install the charger, as shown below.

Getting started

Step 1

Plug the battery connector

securely into the socket

inside the handset battery

compartment. Insert the

supplied battery with the

label THIS SIDE UP facing

up, as indicated.

Battery installation and charging

Install the battery, as shown on pages 6-7. Once you have installed

the battery, the screen indicates the battery status (see the

following table). If necessary, place the handset in the telephone

base or charger to charge the battery. For best performance, keep

the handset in the telephone base or charger when not in use. The

battery is fully charged aer 16 hours of continuous charging. See

the table on page 33 for battery operating times.

If the screen shows Place handset in charger and ashes, you

need to charge the handset without interruption for at least 30

minutes to give the handset enough charge to use the telephone

for a short time. The following table summarizes the battery

charge indicators and actions to take.

Getting started

Battery indicators Battery status Action

The screen is blank,

or shows Place

handset in charger

and (ashing).

Battery has no or

very little charge. The

handset cannot be used.

Charge without interruption

(at least 30 minutes).

The screen shows

Low battery and

(ashing).

Battery has enough

charge to be used for a

short time.

Charge without interruption

(at least 30 minutes).

The screen shows

HANDSET X.

Battery is charged. To keep the battery charged,

place it in the telephone base or

charger when not in use.

NOTE: If you are on a phone call in low battery mode, you hear four short beeps

every minute.

THIS SI

UP / CE

CÔ

TÉ

VERS LE HA

Batt

y Pa

k / Bloc-piles

BT1833

42/BT283342 (2.4V 400mAh Ni-MH)

RNING /

ERTISSEMENT

O NOT BURN

PUNCTURE BA

TTERIES

S INCINÉRER

U PERCER LES PILES.

Made in

China / Fabriqué

chine BY

1021

THIS SIDE

Battery Pack / Bloc

BT183342/BT283342

ARNING /

ERTISS

DO NOT BURN OR PU

S INCINÉRER

Made in China / Fa

Battery installation and charging

Getting started

Step 2

Align the cover at against the battery compartment, then slide it

upwards until it clicks into place.

Step 3

Charge the handset by placing it face forward in the

telephone base or charger. The CHARGE light under

the screen of the handset is on during charging.

IMPORTANT INFORMATION

Use only the supplied rechargeable battery or replacement battery

(model BT183342/BT283342). To order, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

If you do not use the handset for a long time, disconnect and remove

the battery to prevent possible leakage.

•

Aer you install your telephone or power returns following a power

outage, you have to reset the date and time. For instructions, see

Set date/time in the telephone system’s user’s manual for details.

LE HA

CHARGE light

Adding and registering handsets

Before using a new TL88002/TL88002BK handset, you must

telephone system (purchased separately). The telephone system

accommodates up to 12 handsets.

TL88002 (silver) is for use with TL88102 telephone system.

TL88002BK (black) is for use with TL88102BK telephone system.

The handset provided with your telephone system is already

registered as HANDSET. Additional handsets registered to the

telephone system are assigned in sequential order they are

registered (up to HANDSET 12).

You must register each handset separately. When rst purchased,

each expansion handset shows Press [HOLD] on base for 4 sec,

then press [#] on handset.

telephone base

1. Before you begin registration, make sure the

handset displays Press [HOLD] on base for 4

sec, then press [#] on handset.

2. Place the unregistered handset in the

telephone base.

3. Press and hold HOLD on the telephone base

for about four seconds until the telephone base

displays Registering handset.... Then, release

the HOLD button. While the handset is still in

the telephone base, press # (pound key) on

the handset. The handset shows Registering...

Please wait and it takes up to 60 seconds to

complete the registration. The handset and the

telephone base show HANDSET X Registered

(X represents the handset number assigned)

and you hear a beep when the registration completes.

NOTES:

If the registration fails, the handset shows Registration failed. To reset the handset,

unplug the power from the telephone base and the battery from the handset for a

few seconds, then plug them back in. Try the registration process again.

You cannot register a handset if any other system handset is in use.

•

Registration and deregistration

HANDSET X

Registered

Registering...

Please wait

Press [HOLD] on

base for 4 sec,

then press [#]

on handset

Deregistering handsets

You may need to deregister your handsets if:

You have 12 registered handsets and need to replace a handset.

-OR-

You wish to change the designated handset number of your

registered handsets.

You must rst deregister ALL handsets, and then register each

handset you wish to use again, one at a time.

Please read carefully through all the instructions on this page

before beginning the deregistration process.

Deregister all handsets from your telephone base

1. Press and hold HOLD on the telephone base for about 10

seconds until it shows Deregister all handsets?. Release the

HOLD button.

2. Press the YES so key. There is a conrmation tone.

3. The deregistration process takes about 10 seconds to complete.

All handsets show Press [HOLD] on base for 4 sec, then press

[#] on handset when the deregistration completes.

If deregistration fails, you may need to reset the telephone and try

again.

To reset:

1. Pick up the registered handset and then press LINE 1/FLASH or

LINE 2/FLASH.

2. Press OFF/CANCEL and then place the handset back in the

telephone base.

-OR-

Unplug the power adapter from the telephone base, then plug it

back in.

NOTES:

You cannot deregister the handsets if any system handset or the telephone

base is in use.

Even if the battery is depleted, you can still deregister the handsets by following

the steps mentioned above. After the handset is charged for at least 10 minutes,

the screen shows Press [HOLD] on base for 4 sec, then press [#] on handset.

•

Registration and deregistration

Troubleshooting

If you have diculty with your phone, please try the following

suggestions. For Customer Service, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

The handset registration is unsuccessful.

Follow the handset registration instructions to register the

handset again (see Adding and registering handsets on

page 8).

My telephone doesn’t work at all.

Make sure the power cord is securely plugged in.

Make sure you plug the battery connector securely into the

cordless handset.

Make sure you plug the telephone line cord securely and rmly

into the telephone base and the telephone wall jack.

Charge the battery in the cordless handset for at least 16 hours.

For optimum daily performance, return the cordless handset to

the telephone base or charger when not in use.

If the battery is depleted, it may take approximately 30 minutes

to charge the handset before it shows Low battery. See page 6

for details.

Reset the telephone base. Unplug the electrical power. Wait for

approximately 15 seconds, then plug it back in. Allow up to one

minute for the cordless handset and telephone base to reset.

You may need to purchase a new battery. Refer to Battery

installation and charging in this user’s manual on pages 6-7.

The display shows L1>NO LINE or L2>NO LINE. I cannot get a

dial tone.

Try all the suggestions mentioned above.

If the previous suggestions do not work, disconnect the

telephone line cord from your telephone and connect the

telephone line cord to another telephone.

•

Appendix

Troubleshooting

If there is no dial tone on that other telephone either, your

telephone line cord may be defective. Install a new telephone

line cord.

If changing the telephone line cord does not help, the wall

jack (or the wiring to this wall jack) may be defective. Try

using a different wall jack in your home to connect your

TL88102/TL88102BK/TL88202 telephone, or contact your

telephone service provider (charges may apply).

I cannot dial out.

Try all the suggestions mentioned above.

Make sure you have a dial tone before dialing. The cordless

handset may take a second or two to nd the telephone base

and produce a dial tone. This is normal. Wait an extra second

before dialing.

Eliminate any background noise. Noise from a television, radio

or other appliances may cause the phone to not dial out

properly. If you cannot eliminate the background noise, try

muting the cordless handset before dialing, or dialing from

another room with less background noise.

If other phones in your home are having the same problem,

contact your telephone service provider (charges may apply).

My cordless handset isn’t performing normally.

Make sure you plug the power cord securely into the telephone

base. Plug the power adapter into a dierent, working electrical

outlet without a wall switch.

Move the cordless handset closer to the telephone base. You

may have moved out of range.

Reset the telephone base. Unplug the electrical power. Wait for

15 seconds, then plug it back in. Allow up to one minute for the

cordless handset and telephone base to reset.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types

of electronic devices.

•

Appendix

Troubleshooting

Out of range OR No power at base appears on my cordless

handset.

Ensure you plug the telephone base in properly and the power

is on.

Place the cordless handset in the telephone base for one

minute to allow the cordless handset and base to synchronize.

Move the cordless handset closer to the telephone base. You

may have moved out of range.

Reset the telephone base. Unplug the electrical power. Wait for

15 seconds, then plug it back in. Allow up to one minute for the

cordless handset and telephone base to reset.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types

of electronic devices.

The batteries do not hold a charge.

If the cordless handset is in the telephone base or charger and

the charge light is not on, refer to The charge light is o or

blinking on page 17 in this Troubleshooting guide.

Charge the battery in the cordless handset for at least 16 hours.

For optimum daily performance, return the cordless handset to

the telephone base or charger when not in use.

If the battery is depleted, it may take approximately 30 minutes

to charge the handset before it shows Low battery. Refer to

the table on page 6 for details.

You may need to purchase a new battery. Refer to Battery

installation and charging in this user’s manual on pages 6-7.

I hear other calls while using my phone.

Disconnect the telephone base from the telephone jack, and

plug in a dierent telephone. If you still hear other calls, call

your telephone service provider.

•

Troubleshooting

I get noise, static, or weak signals even when I’m near the

telephone base.

If you subscribe to high-speed Internet service (DSL - digital

subscriber line) through your telephone line, you must install a

DSL lter between the telephone line cord and the telephone

wall jack. The lter prevents noise and caller ID problems as

a result of DSL interference. Please contact your DSL service

provider for more information about DSL lters.

You may be able to improve the performance of your cordless

phone by installing your telephone base as far as possible from

any other existing cordless telephone system that may already

be installed.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types

of electronic devices.

Do not install this phone near a microwave oven or on the same

electrical outlet. You may experience decreased performance

while the microwave oven is operating.

If you plug your phone in with a modem or a surge protector,

plug the phone (or modem/surge protector) into a dierent

location. If this does not solve the problem, relocate your phone

or modem farther apart from one another, or use a dierent

surge protector.

Move your phone to a higher location. The phone may have

better reception in a high area.

If other phones in your home are having the same problem,

contact your telephone service provider (charges may apply).

I experience poor sound quality when using the speakerphone.

For increased sound quality while using the speakerphone, place

the handset on a at surface with the dialing keys facing up.

•

Appendix

Troubleshooting

My cordless handset does not ring when I receive a call.

Make sure that the ringer is not o. Refer to Ringer volume in

the TL88102/TL88102BK/TL88202 user’s manual provided with

your telephone.

Make sure you plug the telephone line cord securely into the

telephone base and telephone jack. Make sure you plug in the

power cord securely.

The cordless handset may be too far from the telephone base.

Charge the battery in the cordless handset for at least 16 hours.

For optimum daily performance, return the cordless handset to

the telephone base or charger when not in use.

You may have too many extension phones on your telephone

line to allow all of them to ring simultaneously. Try unplugging

some of the other phones.

The layout of your home or oce may be limiting the operating

range. Try moving the telephone base to another location,

preferably on an upper oor.

If other phones in your home are having the same problem,

contact your telephone service provider (charges may apply).

Test a working phone at the phone jack. If another phone has

the same problem, contact your telephone service provider

(charges may apply).

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types

of electronic devices.

Remove the battery. Replace it and place the cordless handset

into the telephone base. Allow up to one minute for the handset

to reestablish its connection with the telephone base.

Your line cord may be defective. Try installing a new line cord.

•

Appendix

Troubleshooting

My calls cut in and out while I’m using my cordless handset.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types

of electronic devices.

Do not install this phone near a microwave oven or on the same

electrical outlet. You may experience decreased performance

while the microwave oven is operating.

If you plug your phone in with a modem or surge protector, try

plugging the phone (or modem/surge protector) into a dierent

location. If this does not solve the problem, relocate your phone

or modem farther apart from one another, or use a dierent

surge protector.

Move your telephone base to a higher location. The phone may

have better reception when installed in a high area.

If other phones in your home are having the same problem,

contact your telephone service provider (charges may apply).

My caller ID isn’t working.

Caller ID is a subscription service. You must subscribe to this

service from your telephone service provider for this feature to

work on your phone.

The caller may not be calling from an area that supports caller

ID.

Both your and your caller’s telephone service providers must

use caller ID compatible equipment.

If you subscribe to high-speed Internet service (DSL - digital

subscriber line) through your telephone line, you must install a

DSL lter between the telephone line cord and the telephone

wall jack. The lter prevents noise and caller ID problems

resulting from DSL interference. Please contact your DSL

service provider for more information about DSL lters.

•

Appendix

Troubleshooting

System does not receive caller ID when on a call.

Make sure you subscribe to caller ID with call waiting features

from your telephone service provider. Caller ID features work

only if both you and the caller are in areas oering caller

ID service, and if both telephone service providers use

compatible equipment.

I subscribe to a nontraditional telephone service that uses

my computer to establish connections, and my telephone

doesn’t work.

Make sure your computer is powered on.

Make sure your Internet connection is working properly.

Make sure that the soware is installed and running for your

nontraditional telephone service.

Make sure to plug your USB telephone adapter into a dedicated

USB port on your computer. Do not plug it into a multiple port

USB hub (USB splitter) that is not powered.

In a few rare instances, the USB port on your computer may not

have enough power. In these instances, try using a USB hub with

its own external power supply.

If you are using a rewall, it may prevent access to your

nontraditional telephone service provider. Contact your service

provider for more information.

•

La page charge ...

AT&T TL88102 Manuel utilisateur

Marque: AT&T

Modèle: TL88102

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

TL88002

Télécharger le PDF

rapport

dans d''autres langues

English: AT&T TL88102 User manual

AT&T TL88102 Manuel utilisateur

Ce manuel convient également à

AT&T TL88102 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents