Chief TPP2000B Le manuel du propriétaire

Chief
Marque
Chief
Modèle
TPP2000B
Catégorie
Mur
Taper
Le manuel du propriétaire

Ce manuel convient également à

INSTALLATION INSTRUCTIONS
Truss Tilt Adjustable Mount
TPP Series
TPP Series Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the TPP does not exceed 150 lbs
(68.04 kg).
•The weight capacity of the TPP may be LIMITED to the
lowest weight capacity of any other component or
accessory used within the mounting system.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The TPP mount is designed for
installation to a variety of pipe/truss dimensions and can
span a distance of up to 14".
--SAVE THESE INSTRUCTIONS--
Installation Instructions TPP Series
3
DIMENSIONS
DIMENSIONS: INCHES
TPP Series Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Measure
Medir
Messen
Medir
Misurare
Meten
Mesurer
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Hammer
Martillo
Hammer
Martelo
Martello
Hamer
Marteau
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Installation Instructions TPP Series
5
TOOLS REQUIRED FOR INSTALLATION
REQUIRED PARTS (NOT INCLUDED)
#2 (included)
5/32"
7/16" 7/16"
9/16"
9/16"
[TPK Truss/Pole Kit] (example)
X 4 X 8 X 8
TPK-3
or
TPK-4
or
TPK-5
Backplate
A (1)
[TPP mount assembly]
Tilt-adjustable
plate
C (1)
(5/32")
Faceplate
B (1)
[PSB Interface bracket kit]
(example)
PARTS
TPP Series Installation Instructions
6
INSTALLATION
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
The TPP assembly ships configured for vertical pole mounting.
The TPP can be reconfigured to attach to horizontal pipes.
Figure 1
To change the TPP for horizontal pole mounting, proceed to
Horizontal Installation section. To use the TPP in the vertical
configuration, proceed to Vertical Installation section.
Horizontal Installation
1. Detach backplate from tilt adjustable plate/faceplate
assembly by removing the four hex head cap screws. (See
Figure 2)
Figure 2
2. Rotate the backplate 90°.
Figure 3
Faceplate
Backplate
Vertical (Default) Configuration
Tilt-adjustable plate assembly
Faceplate Hex head cap
1
Tilt-adjustable
plate
Backplate
screws (x 4)
2
Installation Instructions TPP Series
7
3. Re-attach backplate to tilt-adjustable plate/faceplate
assembly using the four hex head cap screws (inserted
from inside the tilt-adjustment plate). (See Figure 4)
Figure 4
4. Securely anchor TPP assembly to horizontal poles using
Chief TPK accessory clamps (not included) following
instructions included with TPK kit. (See Figure 5)
Figure 5
5. Proceed to Display Installation section.
Vertical Installation
The TPP assembly ships configured for vertical pole mounting.
1. Securely anchor TPP backplate to vertical poles using Chief
TPK accessory clamps (not included) following instructions
included with TPK kit. (See Figure )
Figure 6
Display Installation
IMPORTANT ! : Make sure no power is supplied to the
display and the latching flag on the TPP is in the
unlocked position before attempting to attach the display.
(See Figure 7)
Figure 7
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the TPP does not exceed 150 lbs
(68.04 kg).
Faceplate
Horizontal Configuration
Hex head cap screws
3
x 4
Backplate
Tilt-adjustmentplate
Horizontal
TPK clamps x 4
(not provided)
4
Installation
2
TPK clamps
(not included)
x 8
Backplate
Note: Faceplate and tilt-adjustable
plate not shown for clarity.
(x 4)
Unlocked
Locked
TPP Series Installation Instructions
8
1. Attach PSB interface bracket (B) to display using the
instructions included with the PSB package.
2. Using two people, slide display with attached interface
bracket (B) down over the four slots in the faceplate of the
TPP (A). Make sure all four mounting buttons engage all
four Q-Latch slots in the TPP (A). (See Figure 8)
Figure 8
3. With the mounting buttons of the display fully engaged in
the slots of the TPP (A), secure the display on the TPP by
raising the flag all the way up to the locked position. (See
Figure 9)
Figure 9
4. If the flag does not fully engage, remove the display and
make sure all four mounting buttons are fully engaged in
slots.
NOTE: A security lock may be installed through the hole in the
Q-Latch flag for added security. See (Optional)
Security Lock section.
Tilt Adjustment
WARNING: IMPROPER HANDLING CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate support
of display while adjusting tilt may cause display to fall! Watch
for pinch points. Do not put your fingers between movable
parts.
1. Loosen tilt adjustment screws, adjust to desired tilt (up to
15°), and tighten tilt adjustment screws. (See Figure 10)
Figure 10
(B)
(A)
(Q-Latch
slots) x 4
Latching flag
Display
2
(on other side)
(A)
Locked
Display
Mounting buttons in slots (x 4)
Note: Trusses not
shown for clarity.
3
(B)
Tilt adjustment screws
1
x 2
Note: Interface bracket, display and
trusses not shown for clarity.
Installation Instructions TPP Series
9
(Optional) Locking Angle Tilt Holes
The TPP can be tilted up to 15 degrees, and features three
holes used to set specific tilt (0°, 5° and 10°).
1. Loosen tilt adjustment screws, adjust to desired tilt, and
tighten tilt adjustment screws. (See Figure 11)
2. Install 1/4" fastener (Grade 2 or better) (not provided) into
desired degree tilt hole (See Figure 11):
•0° (outside hole)
•5° (middle hole)
•10° (inside hole)
Figure 11
Removing the Display
WARNING: IMPROPER HANDLING CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate support
of display while removing it may cause display to fall! Watch
for pinch points. Do not put your fingers between movable
parts.
WARNING: Ensure Q-Latch flag securing display is
completely raised at all times except when removing or
installing display. The flag must be all the way up when
installing or removing cables.
1. With display securely supported, unlock display from TPP
(A) by lowering the flag all the way down to the unlocked
position. (See Figure 12)
Figure 12
2. Using two people, slide display up and out of TPP (A). (See
Figure 13)
Figure 13
Tilt adjustment screws
1
x 2
0° tilt hole
5° tilt hole
10° tilt hole
2
Unlocked
(A)
Locked
1
(A)
(A)
Display
2
(Q-Latch
slots) x 4
TPP Series Installation Instructions
10
(Optional) Security Lock
A hole is provided in the Q-Latch flag and faceplate to
accommodate the insertion of a padlock (not included) or
similar locking device.
1. Insert padlock through lower hole in Q-Latch flag and face
plate. (See Figure 14)
Figure 14
1
Locked Faceplate
Installation Instructions TPP Series
11
TPP Series Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002566 Rev00
2014 Milestone AV Technologies
www.chiefmfg.com
04/14
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Chief TPP2000B Le manuel du propriétaire

Chief
Marque
Chief
Modèle
TPP2000B
Catégorie
Mur
Taper
Le manuel du propriétaire
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents