HME AC70 Mode d'emploi

Taper
Mode d'emploi
Quick Start Guide
HM ELECTRONICS, INC.
2848 Whiptail Loop, Carlsbad, CA 92010 USA
Phone: 1-800-848-4468 Fax: 858-552-0172
Website: www.hme.com Email: [email protected]
HME# PUB - 000xx
Rev A 10/26/20
AC70 BATTERY CHARGER
The AC70 Battery Charger can charge up to four BAT70 lithium-ion
batteries at the same time. LEDs at the charging ports indicate bat-
tery status. Charge time is two hours. The AC70 can be used on a
desktop or mounted on a wall.
TOOLS/EQUIPMENT REQUIRED (for wall mounting only)
Drill and drill bits (~ 3/16th inch (4.76 mm))
Screwdriver (Phillips #2)
Safety Glasses
INSTALLATION AND SETUP
Note: The AC70 is wireless and requires close physical proximity to
communicate with the Base Station/Remote Transceiver.
Desktop instructions:
1. Place the AC70 on a level desktop or shelf.
2. Connect the power adapter to a wall outlet, and the other end to
the power connector on the AC70 (Fig. 1).
Wall mount instructions:
1. Drill two holes two inches apart along a vertical axis on the wall
(avoid electrical or plumbing obstructions).
2. Install the provided hardware but do not tighten, leave a gap (~
¹/8th inch (3.2 mm)) between the screw heads and wall.
3. Align the AC70 mounting holes with the two screws (Fig. 2).
4. Mount the AC70 over the screw heads until flush against the
wall, then slide it down onto the screws to secure it in place.
OPERATION
1. Connect the power adapter to a wall outlet, and the other end to
the power connector on the AC70 (Fig. 1).
2. Position the BAT70 battery correctly for insertion into the AC70.
3. Insert the BAT70 battery into a vacant port to begin charging.
LED activity indicates battery status (see table below).
Battery Charger LED Reference Table
LED Color Status/Description
Green Flashing Green = Charging
Solid Green = Fully charged
Red Flashing Red = Incompatible battery
Red/Yellow Flashing Red & Yellow (alternating)= Fault condition
Mounting Holes
/Slots
Power Connector
AC70 BATTERY CHARGER
REAR VIEW
Fig. 2
Fig. 1
1 2 3 4
HME
WALL OUTLETAC70 BATTERY CHARGER
FRONT VIEW
POWER ADAPTER
Note: Only use the HME
approved Power Adapter
provided with your AC70
*Batteries shown in image
are not included
© 2020 HM Electronics, Inc. All rights reserved.
2
REGULATORY AND SAFETY
CHANGING POWER SUPPLY ADAPTER
1. Replace a power adapter to match your coun-
try's outlet by using your thumb and forefinger to
squeeze in on both sides of the latch (see Fig. 3).
2. Continue squeezing latch and slide the adapter
out, away from the power supply to remove.
3. Release the latch and slide another adapter on until
it bottoms out and the latch clicks to secure it in
place.
TECHNICAL SPECIFICATIONS
Power Supply: Wall plug with switchable adapters
Input Voltage: 100 - 240VAC nominal
Output Voltage: 5V; 4A
MTBF (min.): 300,000 hours demonstrated
AC70 Battery Charger
Input Voltage: 5V; 4A
Charge Output: ~ 3W per port
Temperature
Operating: 32°F - +122°F (0°C - +50°C)
Storage: -40°F - +176°F (-40°C - +80°C)
Humidity: 0 - 95%, non-condensing
Press in here on both
sides of latch to release
Slide in these directions
to remove and replace
Latch
Adapter
Fig. 3
Dimensions
5.0in L x 3.5in W x 1.8in H
(127mm x 88.9mm x 45.72mm)
Weight
0.373lb (0.169kg)
Wireless PAN
2.4GHz Wireless Technology
REGULATORY COMPLIANCE
Applicant Name: HM Electronics, Inc.
Applicant Address: 2848 Whiptail Loop, Carlsbad CA 92010, United States
Manufacturer Name: HM Electronics, Inc.
Manufacturer Address: 2848 Whiptail Loop, Carlsbad CA 92010, United States
Country of Origin: USA
Brand: HME
Model: AC70
Caution: All products are compliant with regulatory requirements detailed in this document when the
user follows all installation instructions and operating conditions per HME specifications.
Caution: Use of accessories and peripherals other than those recommended by HME may void the
product’s compliance as well as the user’s authority to operate the equipment.
Caution: All products are designed for use with the standard, integral or dedicated (external) antenna(s)
that are shipped together with the equipment. Any product changes or modifications will invalidate all
applicable regulatory certifications and approvals.
Caution: The use of software or firmware not supported/provided by HME products may result that the
equipment is no longer compliant with the regulatory requirements.
Warning: The power adapter is the equipment’s disconnection device. The power outlet must be
located nearby the equipment and its access must be easy.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communication. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
Changes or modifications not expressly approved by HME could void the user’s authority to operate this
equipment.
FCC/IC/EC RF EXPOSURE WARNING
This product complies with FCC/IC/EC radiation exposure limits set forth for an uncontrolled
environment.
3
© 2020 HM Electronics, Inc. All rights reserved.
Produits HME sont conformes aux limites IC d’exposition aux rayonnements définies pour un
environnement non contrôlé.
This product may not be co-located or operated in conjunction with any other antenna or transmitter.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une
autre antenne ou transmetteur.
To comply with FCC/IC/EC RF exposure requirements, this unit must be installed and operate at least 20
cm (8 inches) from any person.
Produits HME doivent être installés et utilisés avec distance minimum de 20cm entre le radiateur et
votre corps.
INDUSTRY CANADA COMPLIANCE STATEMENT
Avis de conformité à la réglementation d’Industrie Canada
Cet appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est soumise aux deux conditions suivantes:
(1) cet appareil ne doit pas provoquer d’interféence, et
(2) cet appareil doit accepter toute interféence radioéectrique subie, mêe si l’interféence est
susceptible d’en comprom-ettre le fonctionnement.
Cet éetteur exempt de licence est éuipéd’une antenne intéré. Cet éetteur exempt de licence n’est pas
autoriséàfonctionner avec une autre antenne.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une
autre antenne ou transmetteur.
Cet appareil numérique de la class[A] est conforme à la norme NMB-003 du Canada.
This Class[A] digital device complies with Canadian ICES-003.
4
© 2020 HM Electronics, Inc. All rights reserved.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

HME AC70 Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues