Hitachi SP18V Instruction Manual And Safety Instructions
- Catégorie
- Ponceuses électriques
- Taper
- Instruction Manual And Safety Instructions
MODEL ELECTRONIC SANDER POLISHER
MODÈLE
POLISSEUSE/LUSTREUSE ÉLECTRONIQUE
MODELO
LIJADORA PULIDORA ELECTRÓNICA
SP 18V
DOUBLE INSULATION
DOUBLE ISOLATION
AISLAMIENTO DOBLE
MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE
AVERTISSEMENT
Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la
mort ou de sérieuses blessures corporelles!
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de
ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil
motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant
qu’ils utilisent l’outil motorisé.
INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS
WARNING
Improper and unsafe use of this power tool can result in death or serious bodily
injury!
This manual contains important information about product safety. Please read
and understand this manual before operating the power tool. Please keep this
manual available for others before they use the power tool.
MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD
ADVERTENCIA
¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar
en lesiones serias o en la muerte!
Este manual contiene información importante sobre la seguridad del producto.
Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde
este manual para que puedan leerlo otras personas antes de que utilicen la
herramienta eléctrica.
CONTENTS
Page
OPERATION AND MAINTENANCE
NAME OF PARTS ...................................... 10
SPECIFICATIONS ...................................... 10
ACCESSORIES .......................................... 11
STANDARD ACCESSORIES .................. 11
APPLICATIONS ......................................... 11
PRIOR TO OPERATION ............................. 11
PRACTICAL ELECTRONIC SANDER
POLISHER APPLICATIONS ................... 12
ASSEMBLING AND DISASSEMBLING
THE SANDING DISC AND WOOL BONNET ....
14
MAINTENANCE AND INSPECTION ......... 15
SERVICE AND REPAIRS ........................... 15
PARTS LIST ............................................... 44
TABLE DES MATIERES
Page
INFORMATIONS IMPORTANTES ............ 16
SIGNIFICATION DES MOTS
D’AVERTISSEMENT .............................. 16
SECURITE
CONSIGNES DE SECURITE IMPORTANTES POUR
L’UTILISATION DE TOUS LES OUTILS ELECTRIQUES
... 17
CONSIGNES DE SECURITE IMPORTANTES POUR L’UTILISATION
DU POLISSEUSE/LUSTREUSE ÉLECTRONIQUE
.............. 21
PIECES DE RECHANGE ............................ 21
FICHE POLARISEES .................................. 21
UTILISATION D’UN CORDON DE RALLONGE
... 22
DOUBLE ISOLATION POUR UN
FONCTIONNEMENT PLUS SUR ........... 23
Page
UTILISATION ET ENTRETIEN
NOM DES PIECES ..................................... 24
SPECIFICATIONS ...................................... 24
ACCESSOIRES .......................................... 25
ACCESSOIRES STANDARD .................. 25
APPLICATIONS ......................................... 25
AVANT L’UTILISATION ............................ 25
APPLICATIONS PRATIQUES DE LA POLISSEUSE/
PONCEUSE ÉLECTRONIQUE
......................... 26
MONTAGE ET DÉMONTAGE DU DISQUE DE
PONÇAGE ET DE LA PEAU DE MOUTON
..........
28
ENTRETIEN ET INSPECTION ................... 29
SERVICE APRES-VENTE ET REPARATIONS
... 29
LISTE DES PIÉCES .................................... 44
ÍNDICE
Página
INFORMACIÓN IMPORTANTE ................. 30
SIGNIFICADO DE LAS PALABRAS DE
SEÑALIZACIÓN ..................................... 30
SEGURIDAD
INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA
UTILIZACIÓN DE TODAS LAS HERRAMIENTAS ELÉCTRICAS
... 31
INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA
UTILIZACIÓN DEL LIJADORA PULIDORA ELECTRÓNICA
.... 35
PIEZAS DE REEMPLAZO .......................... 35
ENCHUFES POLARIZADOS ...................... 35
UTILIZACIÓN DE UN CABLE PROLONGADOR
.. 36
AISLAMIENTO DOBLE PARA OFRECER
UNA OPERACIÓN MÁS SEGURA ........ 37
Página
OPERACIÓN Y MANTENIMIENTO
NOMENCLATURA ..................................... 38
ESPECIFICACIONES .................................. 38
ACCESORIOS ............................................ 39
ACCESORIOS ESTÁNDAR .................... 39
APLICACIONES ......................................... 39
ANTES DE LA OPERACIÓN ...................... 39
APLICACIONES PRÁCTICAS DE LA
PULIDORA/LIJADORA ELECTRÓNICA
.... 40
ENSAMBLAJE Y DESENSAMBLAJE DEL
DISCO LIJADOR Y DE LA FUNDA DE LANA
... 42
MANTENIMIENTO E INSPECCIÓN .......... 43
SERVICIO Y REPARACIONES ................... 43
LISTA DE PIEZAS ...................................... 44
English
Page
IMPORTANT INFORMATION ..................... 3
MEANINGS OF SIGNAL WORDS............... 3
SAFETY
IMPORTANT SAFETY INSTRUCTIONS
FOR USING ALL POWER TOOLS ........... 4
IMPORTANT SAFETY INSTRUCTIONS FOR USE OF
THE ELECTRONIC SANDER POLISHER ..................
7
REPLACEMENT PARTS .............................. 7
POLARIZED PLUGS .................................... 7
USE OF EXTENSION CORD ....................... 8
DOUBLE INSULATION FOR SAFER
OPERATION ............................................. 9
Français
Español
English
3
IMPORTANT INFORMATION
Read and understand all of the operating instructions, safety precautions and warnings in
the Instruction Manual before operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the
failure to observe basic safety rules or precautions. An accident can often be avoided by
recognizing a potentially hazardous situation before it occurs, and by observing appropriate
safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and
in the sections which contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identified by
WARNINGS on the power tool and in this Instruction Manual.
Never use this power tool in a manner that has not been specifically recommended by
HITACHI, unless you first confirm that the planned use will be safe for you and others.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in
serious personal injury.
CAUTION indicates a hazardous situations which, if ignored, could result in moderate
personal injury, or could cause machine damage.
NOTE emphasizes essential information.
English
4
SAFETY
INPORTANT SAFETY INSTRUCTIONS
FOR USING ALL POWER TOOLSaaaa
WARNING: Death or serious bodily injury could result from improper or unsafe use
of power tools. To avoid these risks, follow these basic safety instruc-
tions:
READ ALL INSTRUCTIONS
1. NEVER TOUCH MOVING PARTS.
Never place your hands, fingers or other body parts near the tool’s moving parts.
2. NEVER OPERATE WITHOUT ALL GUARDS IN PLACE.
Never operate this tool without all guards or safety features in place and in proper working
order. If maintenance or servicing requires the removal of a guard or safety feature, be sure
to replace the guard or safety feature before resuming operation of the tool.
3. ALWAYS WEAR EYE AND EAR PROTECTOR.
Protect yourself from flying or expelled wood chips, metal particles or other debris by
using protective goggles or equivalent eye protector. Wear ear protector to protect
yourself from excessive noise.
4. PROTECT YOURSELF AGAINST ELECTRIC SHOCK.
Prevent body contact with grounded surfaces such as pipes, radiators, ranges and
refrigeration enclosures. Never operate the tool in damp or wet locations.
5. DISCONNECT TOOLS.
Never leave the tool connected to a power source. Always disconnect the tool from its
power source before servicing, inspecting, maintaining, cleaning and before changing or
checking any parts.
6. AVOID UNINTENTIONAL STARTING.
Don’t carry the tool while it is connected to its power source. Don’t carry the tool with your
finger near the power switch. Be sure the power switch is in the “off” position before
connecting the tool to its power source.
7. STORE TOOL PROPERLY.
When not in use, the tool should be stored in a dry place. Keep out of reach of children.
Lock-out the storage area.
8. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite injuries. Clear all work areas and work benches of
unnecessary tools, debris, furniture, etc.
9. CONSIDER WORK AREA ENVIRONMENT.
Don’t expose power tools to rain. Don’t use power tools in damp or wet locations. Keep
work area well lit and well ventilated.
Don’t use tool in presence of flammable liquids or gases.
Power tools produce sparks during operation. They also spark when switching ON/
OFF. Never use power tools in sites containing lacquer, paint, benzine, thinner,
English
5
gasoline, gases, adhesive agents, and other materials which are combustible or
explosive.
10. KEEP CHILDREN AWAY.
Do not let visitors contact tool or extension cord.
All visitors should be kept safely away from work area.
11. DON’T FORCE TOOL.
It will do the job better and safer at the rate for which it was intended.
12. USE RIGHT TOOL.
Don’t force small tool or attachment to do the job of a heavy-duty tool.
Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting
tree limbs or logs.
13. DRESS PROPERLY.
Do not wear loose clothing or jewelry. They can be caught in moving parts.
Rubber gloves and non-skid footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
14. USE FACE, DUST MASK OR RESPIRATOR IF OPERATION IS DUSTY.
All persons in the area where power tools are being operated should also wear face, dust
mask or respirator.
15. DON’T ABUSE CORD.
Never carry tool by cord or yank it to disconnect from receptacle.
Keep cord from heat, oil and sharp edges.
16. SECURE WORK.
Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands
to operate tool.
17. DON’T OVERREACH.
Keep proper footing and balance at all times.
18. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and if damaged, have repaired by an authorized service
center. Inspect extension cords periodically and replace if damaged.
Keep handles dry, clean, and free from oil and grease.
19. REMOVE ADJUSTING KEYS AND WRENCHES.
Keys and adjusting wrenches remove from tool before turning it on.
20. OUTDOOR USE EXTENSION CORD.
When tool is used outdoors, use only extension cord intended for use outdoors and so
marked.
21. STAY ALERT.
Watch what you are doing. Use common sense. Do not operate tool when you are tired.
Tools should never be used by you if you are under the influence of alcohol, drugs or
medication that makes you drowsy.
22. CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its operation.
English
6
A guard or other part that is damaged should be properly repaired or replaced by an
authorized service center unless otherwise indicated elsewhere in this Instruction
Manual.
Have defective switches replaced by the authorized service center.
Do not use tool if switch does not turn it on and off.
23. NEVER USE A POWER TOOL FOR APPLICATIONS OTHER THAN THOSE SPECIFIED.
Never use a power tool for applications other than those specified in the Instruction
Manual.
24. HANDLE TOOL CORRECTLY.
Operate the tool according to the instructions provided herein. Do not drop or throw the
tool. Never allow the tool to be operated by children, individuals unfamiliar with its
operation or unauthorized personnel.
25. CHECK FOR LIVE WIRES.
Avoid the risk of severe electrical shock by checking for live electrical wires that may be
buried in walls, floors or ceilings. The wires should be de-energized before work begins.
26. KEEP ALL SCREWS, BOLTS AND COVERS TIGHTLY IN PLACE.
Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.
27. DO NOT USE POWER TOOLS IF THE PLASTIC HOUSING OR HANDLE IS CRACKED.
Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not
be used until repaired.
28. BLADES AND ACCESSORIES MUST BE SECURELY MOUNTED TO THE TOOL.
Prevent potential injuries to youself or others. Blades, cutting implements and accessories
which have been mounted to the tool should be secure and tight.
29. KEEP MOTOR AIR VENT CLEAN.
The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check
for dust build-up frequently.
30. OPERATE POWER TOOLS AT THE RATED VOLTAGE.
Operate the power tool at voltages specified on its nameplate.
If using the power tool at a higher voltage than the rated voltage, it will result in
abnormally fast motor revolution and may damage the unit and the motor may burn out.
31. NEVER USE A TOOL WHICH IS DEFECTIVE OR OPERATING ABNORMALLY.
If the tool appears to be operating unusually, making strange noises, or otherwise
appears defective, stop using it immediately and arrange for repairs by a Hitachi
authorized service center.
32. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF.
Don’t leave tool until it comes to a complete stop.
33. CAREFULLY HANDLE POWER TOOLS.
Should a power tool be dropped or struck against hard materials inadvertently, it may be
deformed, cracked, or damaged.
34. DO NOT WIPE PLASTIC PARTS WITH SOLVENT.
Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may
damage and crack plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry
thoroughly.
35. USE ONLY GENUINE HITACHI REPLACEMENT PARTS.
Replacement parts not manufactured by Hitachi may void your warranty and can lead to
malfunction and resulting injuries. Genuine Hitachi parts are available from your dealer.
English
7
IMPORTANT SAFETY INSTRUCTIONS FOR USE OF
THE ELECTRONIC SANDER POLISHER
WARNING: Death or serious bodily injury could result from improper or unsafe use
of the electronic sander polisher. To avoid these risks, follow these basic
safety instructions:
1. Keep away from a revolving sanding disc and wool bonnet.
2. Pay strict attention to sparks.
3. Use the side handle to securely grip the Sander Polisher.
4. Never use depressed center wheel as a disc grinder.
5. Do not use this machine near welding machine.
6. Do not operate on direct current.
7. Should the revolving speed suddenly decrease due to overload, leave the machine from
workpiece and turn the switch OFF and then ON again.
8. Do not push the lock pin while the spindle is running.
9. Always hold the body handle and side handle of the power tools firmly. Otherwise the
counterforce produced may result in inaccurate and even dangerous operation.
REPLACEMENT PARTS
When servicing use only identical replacement parts.
Repairs should be conducted only by a Hitachi authorized service center.
POLARIZED PLUGS
To reduce the risk of electrick shock, this equipment has a polarized plug (one blade is wider
than the other).
This plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to install the proper outlet.
Do not change the plug in any way.
English
8
USE OF EXTENSION CORD
Make sure your extension cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. Table shows the correct size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the
heavier the cord.
MINIMUM GAGE FOR CORD SETS
Total Length of Cord in Feet (Meter)
0 – 25 26 – 50 51 – 100 101 – 150
(0 – 7.6) (7.9 – 15.2) (15.5 – 30.5) (30.8 – 45.7)
Ampere Rating AWG
More Not More
Than Than
0 – 618 16 16 14
6 – 10 18 16 14 12
10 – 12 16 16 14 12
12 – 16 14 12 Not Recommended
WARNING: Avoid electrical shock hazard. Never use this tool with a damaged or
frayed electrical cord or extension cord.
Inspect all electrical cords regularly. Never use in or near water or in any
environment where electric shock is possible.
English
9
DOUBLE INSULATION FOR SAFER OPERATION
To ensure safer operation of this power tool, HITACHI has adopted a double insulation
design. “Double insulation “ means that two physically separated insulation systems have
been used to insulate the electrically conductive materials connected to the power supply
from the outer frame handled by the operator. Therefore, either the symbol “
” or the words
“Double insulation” appear on the power tool or on the nameplate.
Although this system has no external grounding, you must still follow the normal electrical
safety precautions given in this Instruction Manual, including not using the power tool in wet
environments.
To keep the double insulation system effective, follow these precautions:
䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this
power tool, and only genuine HITACHI replacement parts should be installed.
䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy water,
and dry thoroughly.
Never use solvents, gasoline or thinners on plastic components; otherwise the plastic
may dissolve.
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO
OTHER USERS OF THIS TOOL!
English
10
OPERATION AND MAINTENANCE
NOTE:
The information contained in this Instruction Manual is designed to assist you in the safe
operation and maintenance of the power tool.
Some illustrations in this Instruction Manual may show details or attachments that differ
from those on your own power tool
NAME OF PARTS
Fig. 1
Brush Cap
Switch Trigger
Rubber Pad
Lock Pin
Sandig Disc
Gear Cover
Handle
Name Plate
Housing
Side Handle
Dial
Motor Single-Phase, Series Commutator Motor
Power Source Single-Phase 115V AC 60Hz
Current 9.2A
No-Load Speed 1400–3400rpm
Sanding Disc Size:
external diam. 7" (180mm)
hole diam. 7/8" (22mm)
Weight 6.6lbs (3.0kg)
SPECIFICATIONS
English
11
ACCESSORIES
WARNING: Accessories for this power tool are mentioned in this Instruction
Manual.
The use of any other attachment or accessory can be dangerous and
could cause injury or mechanical damage.
STANDARD ACCESSORIES
䡬 Rubber Pad (Code No. 953255) ........................................................................................... 1
䡬 Wrench (Code No. 937913Z) ............................................................................................... 1
䡬 Side Handle (Code No. 981205) .......................................................................................... 1
NOTE:
Accessories are subject to change without any obligation on the part of the HITACHI.
APPLICATIONS
䡬 Sanding metal surfaces.
䡬 Preliminary sanding of metal surfaces before painting, rust removal, removing old paint
before repainting.
䡬 Finishing woodwork, correcting projections of timbers from joints or assemblies.
䡬 Preliminary sanding of wood surfaces before applying paint.
䡬 Polishing or shining painted metal surfaces, such as those of automobiles, trains,
elevators, refrigerators, sewing machines, washing machines, metal appliances, etc.
䡬 Polishing varnished surfaces of wooden furniture, etc.
䡬 Shining synthetic resin or ebonite products.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms to the power source requirements
specified on the product nameplate.
CAUTION: Do not operate on Direct Current power source.
2. Power switch
Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while
the switch is in the ON position, the power tool will start operating immediately and can
cause serious injury.
3. Extension cord
When the work area is far away from the power source, use an extension cord of sufficient
thickness and rated capacity. The extension cord should be kept as short as practicable.
WARNING: Damaged cord must be replaced or repaired.
English
12
4. Check the receptacle
If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact
a licensed electrician to make appropriate repairs.
If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard.
5. Confirming condition of the environment:
Confirm that the work site is placed under appropriate conditions conforming to
prescribed precautions.
When sanding a thin steel plate, depending upon the state of the workbench, a loud noise
will be created due to resounding noise from the steel plate being ground. To eliminate
unwanted noise in this instance, place a rubber mat beneath the material to be ground.
6. Confirming and mounting the sanding disc and wool bonnet
Confirm that the sanding disc is mounted under the specified condition and is firmly
clamped.
For details, refer to the item “Assembling and Disassembling the Sanding Disc and Wool
Bonnet”.
7. Confirm the lock pin
Confirm that the lock pin is disengaged by pushing lock pin two or three times before
switching the power tool on.
8. Fixing the side handle
Screw the side handle into the gear cover.
PRACTICAL ELECTRONIC SANDER POLISHER APPLICATIONS
● For use as a Sander
Motor speed can be varied as desired by rotating the dial:
It is increased by turning the dial towards “E”, decreased by turning it towards “A” (Fig.
2). Select the motor speed appropriate for the work being done. The following table gives
the motor speeds corresponding to each indication on the dial scale and shows the types
of work for which they are suitable.
CAUTION: The dial cannot be rotated further than the “E” or “A” on the scale in their
respective directions.
Dial Indication
A
B
C
D
E
R.P.M.
1400
1900
2400
2900
3400
Type of works
For polishing
For sanding
Dial
Fig. 2
}
}
English
13
1. This unit is designed to provide sufficient polishing (sanding) power with the disc pressed
lightly against the sanding/polishing surface: it is equipped with an electronic control
circuit to ensure that the motor will not slow down even when loaded. There is threfore
no need to press the sanding disc hard against the surface; doing so can overload the
motor, subsequently causing the overload cut device to step into operation by cutting the
motor’s power supply. If this should happen, cut the power switch and turn it back on to
reset the unit: it will resume rotation at the correct motor speed.
2. Rather than applying the entire disc surface to
the metal surface to be ground, use the sander
by inclining it approximately 15°~25° to grind
with the disc peripheral portion. (Fig. 3).
3. Switching on the sander polisher
When the trigger is pulled, the switch is turned
ON, when the trigger is released, the switch is
turned OFF.
4. Precaution after use
Do not lay the sander polisher down immediately
after use in a place where there are many
shavings and much dirt and dust until it has
completely stopped revolving.
● For use as a Polisher
1. Curved surface as well as plain one is treated for finishing. It is recommended to hold the
polisher without pushing on the material, and make the best of its own weight as the
excess pressure on the polishing surface will not only bring unsatisfactory result but also
put unnecessory load on the motor.
2. Polishing compound or wax are used corresponding to the state of finishing and the
maximum polishing effect will be attained when the following method is taken.
Polishing with a sander using fine sanding disc.
Polishing with wool bonnet using compound substance final waxing.
First put the compound and wax in small quantity on the surface to be polished, then, give
a polish with the wool bonnet.
CAUTION: Carefully guard against permitting the cord to touch the wool bonnet or
sanding disc during operation. If the cord touches them, there is danger that
it may become entangled.
Fig. 3
English
14
Fig. 4
Washer nut
Rubber pad
Sanding
disc
Spindle
Lock pin
ASSEMBLING AND DISASSEMBLING THE SANDING DISC AND
WOOL BONNET
WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle
to avoid serious trouble.
● For use as a Sander (Fig. 4)
(1) After placing the sanding disc on the rubber
pad, thread the washer nut onto the spindle.
(2) Press the lock pin to secure the spindle and
tighten the washer nut with a wrench.
(3) To remove the sanding disc, follow the above-
mentioned procedure in reverse order.
Fig. 5
Washer nut
Rubber pad
Wool
bonnet
Spindle
Lock pin
● For use as a Polisher (Fig. 5)
(1) Insert the washer nut through the rubber pad
and thread it onto the spindle.
(2) Press the lock pin to secure the spindle and
tighten the washer nut with a wrench.
(3) Wrap the rubber pad with the hood of the
wool bonnet and firmly secure it by tying a
string around it. Be sure the excess string is
firmly tucked inside the wool bonnet to
prevent it from flying out while polishing.
The unbalanced fitting of the wool bonnet
may cause vibration (Fig. 6).
(4) To remove the wool bonnet, follow the above-
mentioned procedure in reverse order.
CAUTION:
● Use a wrench to tighten the washer nut
sufficiently.
● After releasing the lock pin, check to be sure
that it has returned to its normal position.
Fig. 6
Tuck the excess
string into
Hood
English
15
MAINTENANCE AND INSPECTION
WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle
during maintenance and inspection.
1. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that they are properly tightened.
Should any of the screws be loosened, retighten them immediately.
WARNING: Using this electronic sander polisher with loosened screws is extremely
dangerous.
2. Inspecting the carbon brushes (Fig. 7)
The motor employs carbon brushes which are
consumable parts. Replace the carbon brush
with a new one when it becomes worn to its wear
limit. Always keep carbon brushes clean and
ensure that they slide freely within the brush
holders.
Wear limit
No. of carbon
Fig. 7
43
CAUTION: Using this electronic sander polisher with a carbon brush which is worn in
excess of the wear limit will damage the motor.
NOTE: Use HITACHI carbon brush No. indicated in Fig. 7.
䡬 Replacing carbon brushes:
Remove the brush caps (Fig. 1) with a slotted screwdriver. The carbon brushes can then
be easily removed.
3. Cleaning lock pin section
If the lock pin section becomes dirty, clean it at once.
SERVICE AND REPAIRS
All quality power tools will eventually require servicing or replacement of parts because of
wear from normal use. To assure that only authorized replacement parts will be used, all
service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER,
ONLY.
NOTE:
Specifications are subject to change without any obligation on the part of the HITACHI.
Français
16
INFORMATIONS IMPORTANTES
Lire et comprendre toutes les instructions de fonctionnement, les précautions de sécurité et
les avertissements dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.
La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé
proviennent d’un non respect des règles ou précautions de base de sécurité. Un accident
peut la plupart du temps être évité si l’on reconnaît une situation de danger potentiel avant
qu’elle ne se produise, et en observant les procédures de sécurité appropriées.
Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de
ce mode d’emploi et dans les sections qui contiennent les instructions de fonctionnement
et d’entretien.
Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un
endommagement de la machine sont identifiés par AVERTISSEMENTS sur l’outil motorisé
et dans ce mode d’emploi.
Ne jamais utiliser cet outil motorisé d’une manière qui n’est pas spécifiquement recommandée
par HITACHI sans avoir d’abord vérifié que l’utilisation prévue est sans danger pour vous et
les autres.
SIGNIFICATION DES MOTS D’AVERTISSEMENT
AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont
ignorées, pourraient entraîner de sérieuses blessures personnelles.
PRECAUTION indique des situations dangereuses qui, si elles sont ignorées, pourrait
entraîner de légères blessures personnelles ou endommager la machine.
REMARQUE met en relief des informations essentielles.
Français
17
SECURITE
CONSIGNES DE SECURITE IMPORTANTES POUR IIIII
L’UTILISATION DE TOUS LES OUTILS ELECTRIQUES
AVERTISSEMENT:Une utilisation incorrecte ou dangereuse des outils électriques
peut entraîner la mort ou des blessures graves.
LIRE TOUT CE MODE D’EMPLOI.
1. NE JAMAIS TOUCHER LES PARTIES MOBILES.
Ne jamais placer ses mains, ses doigts ou toute autre partie de son corps près des parties
mobiles de l’outil.
2. NE JAMAIS UTILISER L’OUTIL SANS QUE TOUS LES DISPOSITIFS DE SECURITE NE
SOIENT EN PLACE.
Ne jamais faire fonctionner cet outil sans que tous les dispositifs et caractéristiques de
sécurité ne soient en place et en état de fonctionnement. Si un entretien ou une réparation
nécessite le retrait d’un dispositif ou d’une caractéristique de sécurité, s’assurer de bien
remettre en place le dispositif ou la caractéristique de sécurité avant de recommencer à
utiliser l’outil.
3. TOUJOURS SE PROTEGER LES YEUX ET LES OREILLES.
Pour se protéger des projections de copeaux de bois, particules métalliques ou autres
débris, porter des lunettes de protection ou un masque pour les yeux. Porter des
protections anti-bruit pour se protéger du bruit.
4. SE PROTEGER CONTRE LES DECHARGES ELECTRIQUES.
Empêcher tout contact du corps avec les surfaces mises à la terre, par exemple tuyaux,
radiateurs, plaques de cuisson et enceintes de réfrigération. Ne jamais faire fonctionner
l’outil dans un endroit humide ou mouillé.
5. DEBRANCHER LES OUTILS.
Ne jamais laisser l’outil branché dans une source d’alimentation. Toujours débrancher
l’outil de la source d’alimentation avant tout travail de réparation, d’inspection, d’entretien,
de nettoyage, de remplacement ou de vérification des pièces.
6. EVITER TOUTE MISE EN MARCHE INOPINEE.
Ne pas transporter l’outil pendant qu’il est raccordé à la source d’alimentation. Ne pas
transporter l’outil avec le doigt près de l’interrupteur d’alimentation. Bien s’assurer que
l’interrupteur d’alimentation se trouve sur la position “OFF” (arrêt) avant de raccorder
l’outil à la source d’alimentation.
7. REMISER L’OUTIL CORRECTEMENT.
Lorsqu’on ne se sert pas de l’outil, le remiser dans un endroit sec. Veiller à ce qu’il soit
hors d’atteinte des enfants. Fermer le local de remisage à clé.
8. MAINTENIR L’AIRE DE TRAVAIL PROPRE.
Les aires de travail et les établis encombrés favorisent les accidents. Débarrasser l’aire
de travail et les établis des outils inutiles, débris, meubles, etc.
Français
18
9. CONSIDERER L’ENVIRONNEMENT DE L’AIRE DE TRAVAIL.
Ne pas exposer les outils à la pluie. Ne pas les utiliser dans un endroit humide ou mouillé.
Veiller à ce que l’aire de travail soit bien éclairée et bien aérée.
Ne pas utiliser l’outil en présence de liquides ou de gaz inflammables.
Les outils projettent des étincelles pendant qu’ils fonctionnent. Ne jamais utiliser les
outils dans un lieu renfermant de la laque, de la peinture, du diluant, de l’essence, des gaz,
des produits adhésifs ni aucun autre matériau combustible ou explosif.
10. ELOIGNER LES ENFANTS.
Ne pas laisser les visiteurs toucher l’outil ou le cordon de rallonge.
Tous les visiteurs devront être suffisamment éloignés de l’aire de travail.
11. NE PAS FORCER L’OUTIL.
Il effectuera le travail le meilleur et avec la sécurité maximale au régime pour lequel il a
été conçu.
12. UTILISER L’OUTIL CORRECT
Ne pas forcer sur un petit outil ou accessoire pour faire le travail d’un outil de grande
puissance. Ne pas utiliser un outil pour un usage pour lequel il n’a pas été prévu: par
exemple, ne pas utiliser une scie circulaire pour couper des branches d’arbre ou des
bûches.
13. SE VETIR CORRECTEMENT.
Ne pas porter de vêtements lâches ni de bijoux. Ils pourraient se prendre dans les pièces
en mouvement. Il est recommandé de porter des gants en caoutchouc et des chaussures
anti-glissantes lors d’un travail à l’extérieur.
Porter un couvre-chef qui recouvre les cheveux longs.
14. PORTER UN MASQUE, UN MASQUE ANTI-POUSSIERE OU UN APPAREIL RESPIRATOIRE
SI LE TRAVAIL DOIT DEGAGER DE LA POUSSIERE.
Toutes les personnes présentes sur l’aire de travail devront également porter un masque,
un masque anti-poussière ou un appareil respiratoire.
15. NE PAS MALTRAITER LE CORDON.
Ne jamais transporter l’outil par le cordon ni tirer brusquement sur le cordon pour le
débrancher.
Eloigner le cordon de la chaleur, de la graisse et des surfaces tranchantes.
16. FIXER LA PIECE.
Utiliser des dispositifs de serrage ou un étau pour tenir la pièce. Cela sera plus sûr que
de tenir la pièce à la main et libérera les deux mains pour le travail.
17. NE PAS TROP SE PENCHER.
Garder une bonne assise et un bon équilibre à tout moment.
18. ENTRETENIR LES OUTILS AVEC SOIN.
Maintenir les outils aiguisés et propres pour optimiser le travail et la sécurité.
Suivre les instructions de graissage et de remplacement des accessoires.
Vérifier périodiquement les cordons d’outil et les faire réparer par un centre de réparation
agréé s ’ils sont endommagés. Vérifier périodiquement les cordons de rallonge et les faire
remplacer s’ils sont endommagés. Maintenir les poignées sèches et propres, et enlever
toute graisse et toute huile dessus.
19. RETIRER LES CLAVETTES DE REGLAGE ET LES CLES.
Les clés et les clavettes de réglage devront être retirées de l’outil avant de sa mise en
marche.
Français
19
20. CORDONS DE RALLONGE POUR UTILISATION A L’EXTERIEUR.
Si l’outil doit être utilisé dehors, utiliser exclusivement des cordons de rallonge conçus
pour un usage extérieur et marqués à cet effet.
21. RESTER SUR SES GARDES.
Bien faire attention à ce que l’on fait. Faire preuve de bon sens. Ne pas utiliser l’outil
lorsqu’on est fatigué.
Ne jamais utiliser l’outil si l’on est sous l’influence d’alcool, de drogues ou de médicaments
qui rendent somnolent.
22. VERIFIER S’IL Y A DES PIECES ENDOMMAGEES.
Avant de continuer à utiliser l’outil, inspecter attentivement les protections ou autres
pièces endommagées pour voir si l’outil pourra fonctionner correctement et effectuer le
travail pour lequel il est conçu. Vérifier l’alignement et le couplage des pièces mobiles,
le voilage des pièces mobiles, la présence de pièces cassées, le montage, et toute autre
condition susceptible d’affecter le bon fonctionnement.
Si une protection ou une pièce est endommagée, la faire réparer ou remplacer par un
service après-vente agréé, sauf spécification contraire dans ce mode d’emploi.
Faire remplacer les interrupteurs défectueux par un centre de réparation agréé.
Ne pas utiliser l’outil si l’interrupteur ne fonctionne pas.
23. NE JAMAIS UTILISER UN OUTIL MOTORISE POUR DES APPLICATIONS AUTRES QUE
CELLES SPECIFIEES.
Ne jamais utiliser un outil motorisé pour des applications autres que celles spécifiées
dans le mode d’emploi.
24. MANIPULER L’OUTIL CORRECTEMENT
Utiliser l’outil de la façon indiquée dans ce mode d’emploi. Ne pas laisser tomber ou
lancer l’outil. Ne jamais permettre que l’outil soit utilisé par des enfants, des personnes
non familiarisées avec son fonctionnement ou un personnel non autorisé.
25. VERIFIER S’IL Y A DES FILS SOUS TENSION.
Pour éviter tout risque de choc électrique grave, vérifier s’il y a des fils électriques sous
tension encastrés dans le mur, le plancher ou le plafond. Couper l’alimentation des fils
avant le travail.
26. MAINTENIR TOUTES LES VIS, TOUS LES BOULONS ET LES COUVERCLES FERMEMENT
EN PLACE.
Maintenir toutes les vis, tous les boulons et les couvercles fermement montés. Vérifier
leurs conditions périodiquement.
27. NE PAS UTILISER LES OUTILS MOTORISES SI LE REVETEMENT DE PLASTIQUE OU LA
POIGNEE EST FENDU.
Des fentes dans le revêtement ou la poignée peuvent entraîner une électrocution. De tels
outils ne doivent pas être utilisés avant d’être réparé.
28.LES LAMES ET LES ACCESSOIRES DOIVENT ETRE FERMEMENT MONTES
SUR L’OUTIL.
Eviter les blessures potentielles personnelles et aux autres. Les lames, les instruments
de coupe et les accessoires qui ont été montés sur l’outil doivent être fixés et serrés
fermement.
29. GARDER PROPRES LES EVENTS D’AIR DU MOTEUR
Les évents d’air du moteur doivent être maintenus propres de façon que l’air puisse
circuler librement tout le temps. Vérifier les accumulations de poussière fréquemment.
Français
20
30. UTILISER L’OUTIL MOTORISE A LA TENSION NOMINALE.
Utiliser l’outil motorisé à la tension spécifiée sur sa plaque signalétique.
Si l’on utilise l’outil motorisé avec une tension supérieure à la tension nominale, il en
résultera une rotation anormalement trop rapide du moteur et cela risque d’endommager
l’outil et le moteur risque de griller.
31. NE JAMAIS UTILISER UN OUTIL DEFECTUEUX OU QUI FONCTIONNE ANORMALEMENT.
Si l’outil n’a pas l’air de fonctionner normalement, fait des bruits étranges ou sans cela
paraît défectueux, arrêter de l’utiliser immédiatement et le faire réparer par un centre de
service Hitachi autorisé.
32. NE JAMAIS LAISSER FONCTIONNER L’OUTIL SANS SURVEILLANCE. LE METTRE HORS
TENSION.
Ne pas abandonner l’outil avant qu’il ne soit complètement arrêté.
33. MANIPULER L’OUTIL MOTORISE AVEC PRECAUTION.
Si un outil motorisé tombe ou frappe un matériau dur accidentellement, il risque d’être
déformé, fendu ou endommagé.
34. NE PAS ESSUYER LES PARTIES EN PLASTIQUE AVEC DU SOLVANT.
Les solvants comme l’essence, les diluants, la benzine, le tétrachlorure de carbone et
l’alcool peuvent endommager et fissurer les parties en plastique. Ne pas les essuyer avec
de tels solvants.
Essuyer les parties en plastique avec un chiffon doux légèrement imbibé d’une solution
d’eau savonneuse et sécher minutieusement.
35. UTILISER EXCLUSIVEMENT DES PIECES DE RECHANGE HITACHI D’ORIGINE.
Les pièces de rechange non fabriquées par Hitachi risquent d’annuler la garantie et
d’entraîner un mauvais fonctionnement et des blessures. Les pièces Hitachi d’origine
sont disponibles auprès de son concessionnaire.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Hitachi SP18V Instruction Manual And Safety Instructions
- Catégorie
- Ponceuses électriques
- Taper
- Instruction Manual And Safety Instructions
dans d''autres langues
- English: Hitachi SP18V
- español: Hitachi SP18V
