SolarEdge PB250-AOB Guide d'installation

Disclaimers

SolarEdge Installation Guide – MAN-01-00002-1.6

2

Disclaimers

Important Notice

No part of this document may be reproduced, stored in a retrieval system or transmitted, in

any form or by any means, electronic, mechanical, photographic, magnetic or otherwise,

without the prior written permission of SolarEdge Inc.

This document is solely for the use of SolarEdge customers and employees.

The material furnished in this document is believed to be accurate and reliable. However,

SolarEdge assumes no responsibility for the use of this material. SolarEdge reserves the

right to make changes to the material at any time and without notice. You may refer to the

SolarEdge web site (www.solaredge.com) for the most updated version.

All company and brand products and service names are trademarks or registered

trademarks of their respective holders.

Exclusion of Liability

The general terms and conditions of delivery of SolarEdge shall apply.

The content of these documents is continually reviewed and amended, where necessary.

However, discrepancies cannot be excluded. No guarantee is made for the completeness of

these documents.

Table of Contents

SolarEdge Installation Guide – MAN-01-00002-1.6

3

Table of Contents

Disclaimers .................................................................................................... 2

Handling and Safety Instructions ................................................................ 6

Support and Contact Information ............................................................... 8

Chapter 1: Introducing the SolarEdge Power

Harvesting System .................................................................. 9

What is the SolarEdge Power Harvesting Solution? ................................. 9

SolarEdge Power Optimizer .................................................................... 9

Single Phase Inverter ............................................................................. 10

SolarEdge Monitoring Portal ................................................................. 11

Installation Workflow................................................................................. 12

Transport and Storage ............................................................................... 13

Single Phase Inverter Transport ............................................................. 13

Single Phase Inverter Storage ................................................................ 13

Equipment List............................................................................................ 13

Chapter 2: Installing the Power Optimizers ...................... 15

Applicable Notes and Warnings ................................................................ 15

Step 1, Mounting the Power Optimizers ................................................... 18

Step 2, Connecting Each PV Module to a Power Optimizer ..................... 20

OP250-LV, OP300-MV and OP400-MV .............................................. 20

PB250-AOB and PB350-AOB .............................................................. 21

Connecting Power Optimizers ............................................................... 22

Step 3, Connecting Power Optimizers in Strings ..................................... 23

Verifying Proper Power Optimizer Connection .................................... 24

Step 4, Recording Installation Information .............................................. 26

Chapter 3: Installing the Inverter ....................................... 27

Identifying the Inverter .............................................................................. 27

Selecting the Mounting Location ............................................................... 27

Chassis Clearance .................................................................................. 27

Mounting the Inverter ................................................................................ 28

Connecting the Inverter ............................................................................. 31

Inverter Connection Overview .............................................................. 31

AC Grids Supported .............................................................................. 34

Connecting the Single Phase Inverter .................................................... 35

Table of Contents

SolarEdge Installation Guide – MAN-01-00002-1.6

4

Completing the Single Phase Inverter Installation ................................. 41

Installing the AC/DC Safety Switch ...................................................... 42

Ground Fault Circuit Interrupter ............................................................. 55

Chapter 4: Commissioning the Installation ....................... 56

Commissioning – Workflow ....................................................................... 56

Step 1, Activating the System ................................................................ 57

Step 2, Pairing Power Optimizers to the Inverter .................................. 58

Step 3, Verifying Proper Operation ........................................................ 60

Step 4, Reporting and Monitoring Installation Data .............................. 61

Chapter 5: Replacing and Adding System Components .. 64

Modifying an Existing Installation ............................................................ 64

Chapter 6: Setting Up Communication .............................. 66

Communication Dataflow .......................................................................... 66

Connector Panel .......................................................................................... 66

Communication Types ................................................................................ 67

Creating an RS232 (UART) Connection ................................................... 69

Creating an Ethernet (LAN) Connection.................................................. 70

Creating an RS485 Bus Connection .......................................................... 75

Verifying the Connection ........................................................................... 81

Troubleshooting Communication .......................................................... 82

Chapter 7: Inverter User Interface ..................................... 83

Inverter LCD Panel and LEDs .................................................................. 83

Inverter LCD Panel and User Buttons ................................................... 84

Configuring the Inverter Using the LCD Panel and User Buttons ......... 88

Inverter Configuration Menu Options ................................................... 95

LCD Button Menu Options ................................................................... 98

Configuring the Inverter Using the SolarEdge Configuration Tool ....... 99

Appendix A: Errors and Troubleshooting ....................... 100

Appendix B: Technical Specifications .............................. 108

Single Phase Inverter ................................................................................ 108

OP250-LV, OP300-MV and OP400-MV .................................................... 111

PB250-AOB and PB350-AOB .................................................................. 113

Table of Contents

SolarEdge Installation Guide – MAN-01-00002-1.6

5

Appendix C: Power Optimizer Mechanical

Specifications ....................................................................... 115

OP250-LV, OP300-MV, OP400-MV Power Optimizers ....................... 116

PB250-AOB and PB350-AOB Power Optimizers .................................. 117

Appendix D: Inverters Power De-rating .......................... 118

Appendix E: Limited Product Warranty ......................... 119

Handling and Safety Instructions

SolarEdge Installation Guide – MAN-01-00002-1.6

6

Handling and Safety Instructions

During installation, testing and inspection adherence to the following handling

and safety instructions is mandatory.

Safety Symbols

The following safety symbols are used throughout this document. Familiarize

yourself with the symbols and their meaning before installing or operating this

instrument.

WARNING!

Denotes a hazard. It calls attention to a procedure that, if not correctly perf

ormed

or adhered to, could result in

injury or loss of life. Do not proceed beyond a

warning note until the indicated conditions are fully understood and met.

Dénote un risque: il attire l'attention sur une opération qui, si elle n'est pas faite ou

suivi c

orrectement, pourrait causer des blessures ou un danger de mort. Ne pas

dépasser une telle note avant que les conditions requises soient totallement

comprises et accomplies.

CAUTION:

Denotes a hazard. It calls attention to a procedure that, if not corre

ctly performed

or adhered to, could result in

damage or destruction of the instrument. Do not

proceed beyond a caution sign until the indicated conditions are fully understood

and met.

Dénote un risque: il attire l'attention sur une opération qui, si elle

n'est pas faite ou

suivi correctement, pourrait causer un dommage ou destruction de l'équipement.

Ne pas dépasser une telle note avant que les conditions requises soient

totallement comprises et accomplies.

NOTE:

Denotes additional information about

the current subject.

IMPORTANT SAFETY FEA

TURE:

Denotes information about safety issues.

Handling and Safety Instructions

SolarEdge Installation Guide – MAN-01-00002-1.6

7

Instructions

WARNING!

The cover must only be opened after shutting off the AC

/

DC switch located below

the inverter and waiting five minutes. This removes both DC

and AC voltage from

the inverter

.

Do not remove the inverter cover before five minutes have elapsed after

disconnecting all sources of power. Only use lockable connectors for DC input.

Otherwise, there is a risk of electric shock form energy stored in the

capacitor.

Ne pas ouvrir le couvercle de l'onduleur avant d'avoir coupé l'interrupteur CA/CC

situé en dessous de l'onduleur et que cinq minutes ne se soient ecoulées. Cela

supprime les tensions CC et CA de l'onduleur.

Ne pas ouvrir le couvercle de l'ondul

eur avant que cinq minutes ne se soient

ecoulées après coupure de toutes les sources de puissance. Sinon, il y a un

risque de choc électrique provenant de l'énergie stockée dans le capaciteur.

WARNING!

Before operating the Single Phase Inverter, ensure

that the system has been

grounded properly.

Avant d'utiliser l'onduleur monophasé, assurez

-vous que le système est

correctement mis à la terre.

WARNING!

No user

-serviceable parts inside. This unit must be opened only by qualified

service personnel.

Repairs or testing under power must only be performed by

qualified

service personnel who are familiar with and qualified to work with this

Single Phase Inverter.

Ne contient aucune pièce réparable par l'utilisateur. L’unité ne doit être ouverte

que par un

technicien qualifié dans le cadre de l'installation et de la maintenance

.

Les réparations ou les tests électriques sous tension ne doivent être effectués

que par des techniciens qualifiés de SolarEdge, possèdant les connaissances et

les qualifications nécessaires pour travailler avec cet onduleur monophasé.

WARNING!

The supplied AC/DC

Safety Switch meets all requirements for a code-compliant

installat

ion of this ungrounded system. The DC section opens both the positive

and negative conductors.

Le sectionneur CA/CC externe (inclus) repond aux exigences de conformité pour

l’installation de ce système non

-relié à la terre. Le coupeur CC ouvre les

conducteurs positif et négatif.

Support and Contact Information

SolarEdge Installation Guide – MAN-01-00002-1.6

8

WARNING!

This unit must be connected only to a dedicated

AC branch circuit with a

maximum

Overcurrent Protection Device (OCPD) of 40 A.

Cet appareil doit être connecté uniquement à un circuit de dérivation dédié avec

un coéfficient TPOC (

dispositif de protection contre les surintensités) maximal de

40 A.

Support and Contact

Information

If you have technical problems concerning our products, please contact us:

USA and Canada: 1877 360 5292

Germany: 089-45459730 and 089-4161703-39

France: 0800917410

Italy: 800 784 824

United Kingdom: 08002061058

Israel: 073 2403118

Australia: 1800149229

Rest of World: +1 (650) 319-8843

Fax: +972 73 240-3117

Email to:

 support@solaredge.com (US and Canada)

 support@solaredge.com (all other countries)

Before contact, please gather the following information:

 Inverter and power optimizer type.

 Serial number of the inverter and the power optimizer in question.

 The error indicated on the inverter screen or on the SolarEdge Monitoring

Portal.

 System configuration information, including the type and number of modules

connected and the number and length of strings.

 The communication method to the SolarEdge server.

The Support option on the top right of the SolarEdge Configuration Tool’s

main window can be used to automatically collect all relevant information to be

sent to SolarEdge Professional Services for support. This option is described in

detail in the SolarEdge Configuration Tool Software Guide.

Introducing the SolarEdge Power Harvesting System

SolarEdge Installation Guide – MAN-01-00002-1.6

9

Chapter 1

Int

roducing the SolarEdge Power

Harvesting System

What is the SolarEdge Power

Harvesting Solution?

The SolarEdge power harvesting solution maximizes the power output from any

type of solar PV installation while reducing the average cost per watt. The

sections below describe each of the system’s components.

SolarEdge Power Optimizer

SolarEdge power optimizers can be connected to existing PV modules in order to

maximize power harvesting by locally performing Maximum Power Point

Tracking (MPPT) at the PV module level.

The power optimizers keep the string voltage fixed, regardless of the length of the

string and of the environmental conditions. Each SolarEdge power optimizer

directly transmits performance data from every PV module over the power line.

Three types of power optimizers are provided by SolarEdge, as follows:

 Module add-on solutions, connected during installation to one or more PV

module. P/N: OP250-LV, OP300-MV, OP400-MV, OP480-IV, PB250-AOB

and PB350-AOB.

 Module Embedded Solution (CSI), is supplied embedded into a PV

module.

Introducing the SolarEdge Power Harvesting System

SolarEdge Installation Guide – MAN-01-00002-1.6

10

You may refer to the SolarEdge power optimizer datasheets in order to determine

which power optimizer is most suitable for you requirements.

Figure 1: Add-On Box Solution

Single Phase Inverter

The Single Phase Inverter efficiently converts DC power received from the PV

modules into AC power that can be fed into the main circuit board of the site and

from there to the grid. The inverter also receives the monitoring data from each

power optimizer and transmits it to a central server (called the Monitoring Server)

through an Ethernet network to an external modem connection.

Figure 2: Single Phase Inverter

Mounting Hole

Top

Front

Bottom

Heat Sink Fins

LCD

Introducing the SolarEdge Power Harvesting System

SolarEdge Installation Guide – MAN-01-00002-1.6

11

Single Phase Inverter Package Contents

The following lists the contents of the Single Phase Inverter installation package:

 One SolarEdge Single Phase Inverter.

 One wall-mounting bracket.

 Two flat head screws for fastening the inverter to the wall-mounting bracket.

 Installation Guide.

 Quick Installation Guide.

SolarEdge Monitoring Portal

The SolarEdge Monitoring Portal enables you to monitor the technical and

financial performance of one or more SolarEdge Photovoltaic sites. It provides

information about present and past performance of each PV module individually

and about the system as a whole.

NOTE:

You may refer to the

SolarEdge Monitoring Portal User Guide available on the

SolarEdge website at www.solaredge.com for more information about this option.

Introducing the SolarEdge Power Harvesting System

SolarEdge Installation Guide – MAN-01-00002-1.6

12

Installation Workflow

The following provides an overview of the workflow for installing and setting up

a new SolarEdge site. Most of these procedures can also be used for adding

components to an existing SolarEdge site.

Page

15

Page

s 26 and 61

Page

27

Page

56

Page

66

Page

88

Recording Power Optimizer Serial

Numbers

Installing the Inverter and

Connecting the String to the

Inverter

Commissioning and Activating the

Installation

Connecting the Inverter to the

SolarEdge Monitoring Server

Configuring the Inverter

Connecting Power Optimizers

to Panels and to a String

Introducing the SolarEdge Power Harvesting System

SolarEdge Installation Guide – MAN-01-00002-1.6

13

Transport and Storage

Single Phase Inverter Transport

The Single Phase Inverter should be transported in its original packaging, facing

up and without exposing the Single Phase Inverter to unnecessary shocks. If the

original package is no longer available, a similar box can be used which can

withstand the weight of the Single Phase Inverter (<52 lb/25 kg), has a handle

system and can be closed fully.

Single Phase Inverter Storage

Store the Single Phase Inverter in a dry place where ambient temperatures are

always between -25°C and +60°C.

Equipment List

Standard tools can be used during the installation of the SolarEdge system. The

following is a recommendation of the equipment to be used when installing a

SolarEdge system:

 Allen screwdriver for M6 and M5 screw types.

 Flat Head screwdriver.

 Electrical screwdriver (tester).

 Drilling machine and bits suitable for a wall or pole, where the inverter

mounting bracket is installed.

 Suitable screws for attaching the inverter mounting bracket to a wall.

 5/16” screws for attaching the power optimizer to the racking.

 Wire cutters.

 Wire strippers.

 Voltmeter.

Introducing the SolarEdge Power Harvesting System

SolarEdge Installation Guide – MAN-01-00002-1.6

14

For installing the communication option, you may also need the following:

 For Ethernet: RJ45 connectors

 For RS485: Four- or six-wire twisted pair telephone cable

An inverter has either RJ45/RJ11 connectors or block terminal connectors for

communication. To install an inverter with RJ45/RJ11 connectors, you also

require the following:

 For Ethernet:

• CAT5 twisted pair Ethernet cable

• RJ45 crimping tool

 For RS485:

• RJ11 six-pin connector (also known as RJ25)

• RJ11 crimping tool

Installing the Power Optimizers

SolarEdge Installation Guide – MAN-01-00002-1.6

15

Chapter 2

Installing the Power Optimizers

Applicable Notes and Warnings

The following notes and warnings apply when installing the SolarEdge power

optimizers:

WARNING:

Before performing these steps, turn OFF the Single Phase Inverter by turning off the

ON/OFF switch at the bottom of the inverter. All inverters in an installation site must

be switched OFF in this manner.

Avant de faire ces étapes, éteignez l'onduleur mon

ophasé en mettant sur OFF

l'interrupteur ON/OFF situé au bas de l'onduleur. Tous les onduleurs sur un site

d'installation doivent être etteints de la même manière.

CAUTION:

If installing directly on the module or module frame, first consult the module

manufacturer for guidance regarding location and the impact on the module

warranty.

Pour installation à m

ême le module ou la monture du module, consultez d'abord le

fabricant du module sur la position et son impact sur la garantie du module.

CAUTION:

Unused connectors must be sealed with appropriate plugs (not provided). Leaving

connectors

exposed may be unsafe or create funcional problems in the installation

and will

void the warranty.

Les connecteurs non

-utilisés doivent être scellés avec des bouchons (non-fournis).

Laisser des connecteurs exposés peut

être dangereux ou peut créer des probl

èmes

fonctionels lors de l’installation et par cons

équent ne seront pas couvert par la

guarantie.

Installing the Power Optimizers

SolarEdge Installation Guide – MAN-01-00002-1.6

16

CAUTION:

SolarEdge power optimizers and inverters use

connectors from the following

manufacturers:



Multi Contact MC4



Amphenol H4



Tyco keyed connector



Huber Suhner Raddox

Installing a SolarEdge system without ensuring compatibility of the module

connectors with the optimizer connectors may be unsafe and coul

d cause

functionality problems such as ground faults, resulting in inverter shut down.

In order to ensure mechanical compatibility of the SolarEdge optimizers and the

modules to which they are connected:



Use identical connectors from the same manufacturer and of the same type on

both the power optimizers and on the modules; or



Verify that the connectors are compatible in the following way:

▪ The connector manufacturer should explicitly verify compatibility with the

SolarEdge connector; and

▪ A third-party test report by one of the listed external labs (TUV, VDE,

Bureau Veritas UL, CSA, InterTek) should be obtained, verifying the

compatibility of the connectors.

Les optimiseurs de puissance et onduleurs SolarEdge utilisent des connecteurs des

fabricants suivants:



Multi Contact MC4



Amphenol H4



Tyco connecteur clé



Huber suhner Raddox

Les connecteurs du module doivent être mécaniquement compatibles avec les

optimiseurs de puissance. Sinon, le système SolarEdge installé peut être

dangereux ou causer des problèmes fonctionnels, tels que les défauts de terre, qui

peuvent provoquer un arręt

de l’onduleur.

Afin d'assurer la compatibilité mécanique entre les optimiseurs de puissance

SolarEdge et les modules auxquels ils sont connectés, il faut

:



Utiliser des connecteurs identiques du même fabricant et du même type aussi

bien pour les optimiseurs de puissance que pour les modules.



Vérifiez que les connecteurs sont compatibles de la manière suivante:

▪ Le fabricant du connecteur doit explicitement vérifier la compatibilité

avec le connecteur SolarEdge.

▪ Un rapport de test de tierce partie doit être effectué par l’un des

laboratoires externes indiqués ci-dessous:(TUV, VDE, Bureau Veritas UL,

CSA, Intertek), qui vérifiera la compatibilité des connecteurs.

Installing the Power Optimizers

SolarEdge Installation Guide – MAN-01-00002-1.6

17

NOTE:

The power optimizer is waterproof

when the input and output cable connectors are

mated

, and has no need for shelter. Do NOT leave the optimizer exposed to water

unless the connectors are mated.

The power optimizer can be placed in any

orientation, meaning there is no up side.

NOTE:

The power optimizer should be mounted in a location that is either ventilated or that

has a free space of air around it for heat dissipation.

NOTE

:

Mounting brackets are suited to either a flat surface or a pole and can be

attached

to any surface texture.

I

MPORTANT SAFETY FEATURE:

As long as the power optimizers are unconnected to the inverter and the inverter is

OFF, the power optimizers will output a safe 1V voltage during installation.

IMPORTANT NOTE:

SolarEdge

power optimizers are energized by the PV modules to which they are

connected. String length must not be less than eight power optimizers or the entire

string may shut down. (Please refer to the power optimizer datasheets for the exact

minimum and maximum number of power optimizers permitted in a string.)

NOTE:

Completely shaded PV modules may cause the affected power optimizers to

temporarily shut down. This will not affect the performance of the other power

optimizers in the string, as long as the minimum string length requirement is met

when taking into accoun

t the lighted panels only. If under typical conditions fewer

than eight modules will remain unshaded, add more PV modules.

Installing the Power Optimizers

SolarEdge Installation Guide – MAN-01-00002-1.6

18

Step 1, Mounting the Power

Optimizers

IMPORTANT NOTE:

Be sure to record

power optimizer serial numbers and locations during their

installation, as this information may be required later for troubleshooting

, and is

necessary for proper physical layout on the monitoring website.

 Determine the mounting location of each power optimizer. The power

optimizer should be mounted in a place where it can be mounted securely

using both mounting holes. It must also be located near enough so that the

power optimizer can connect to a single PV module (for the OP250-LV,

OP300-MV, OP400-MV, PB250-AOB and PB350-AOB models). Mark all

mounting hole locations.

 Each power optimizer must be attached to the rack using both mounting holes.

 Drill the holes.

CAUTION:

Do not drill through the power optimizer or through the mounting holes. The

vibrations created by the drill can damage the power optimizer

and will void

the warranty.

Ne pas percer à travers la optimiseur de puissance

ou ses trous de fixation.

Les vibrations qui en résulteraient peuvent endommager la optimiseur de

puissance.

 Mount one power optimizer at each location using 5/16” screws and washers.

 Verify that the power optimizer is securely attached.

Installing the Power Optimizers

SolarEdge Installation Guide – MAN-01-00002-1.6

19

WARNING!

The metallic enclosure of the

power optimizer must have equipment

grounding. Perform the following in order to properly ground the

power

optimizer

enclosure. Grounding of the power optimizer can be performed in

either of two ways:

L'enceinte metallique de la optimiseur de puissance doit

ê

tre mise à la terre.

Suivre la procédure suivante afin de mettre l'enceinte de la optimiseur de

puissance à la terre convenablement. La mise à la te

rre de la optimiseur de

puissance peut s'accomplir par l'une des deux méthodes suivantes:



For mounting the power optimizer on a grounded rail, use the provided

5/16'' stainless steel star washer between the railing and the flat side of

the mounting

bracket. The star washer should break through the anodize

coating of the railing to ensure low-resistive connection.

Pour le montage de l'optimiseur de puissance sur rail mis à la terre,

utilisez la rondelle étoile en acier inoxydable 5/16'' fournie,

entre le rail et

le côté de la bretelle de montage non recouverte. La rondelle étoile doit

traverser le revêtement anodisé du rail pour assurer une adhésion à

basse résistivité.



For mounting the power optimizer on an un-grounded structure (such as

a wooden structure), connect an equipment grounding conductor to the

grounding terminal. The grounding terminal will accept a wire size of

6-14 AWG, and must be sized for equipment per NEC 250.122.

Pour le montage de l'optimiseur de puissance sur un

e structure non mise

à la terre (comme une structure en bois), connectez un conducteur de

mise à la terre à la borne de mise à la terre. La borne de mise à la terre

accepte une taille de fil de 6-14 AWG, et doit être dimensionné pour

équipement conforme au NEC 250.122.

Installing the Power Optimizers

SolarEdge Installation Guide – MAN-01-00002-1.6

20

Step 2, Connecting Each PV Module

to a Power Optimizer

WARNING!

Before performing this step, turn OFF the Single Phase Inverter by turning off

the ON/OFF switch at the bottom of the inverter and the DC switch of the main

circuit

board. All inverters in an installation site should be switched OFF in this

manner. This step is required to verify that the power optimizers will output a

safe 1V voltage during installation.

Avant d'effectuer cette étape, éteignez l'onduleur monophasé av

ec le

sectionneur ON/OFF en bas de l'o

nduleur et avec le sectionneur CA/CC. Tous

les onduleurs d'une installation doivent être éteints de cette manière. Cette

étape est requise pour vérifier que les optimiseurs de puissance produisent une

tension de sécurité de 1V pendant l'installation.

OP250-LV, OP300-MV and OP400-MV

These power optimizers connect to a single PV module via its two inputs (a plus

and a minus).

Figure 3: OP250-LV, OP300-MV and OP400-MV

Input +

Input -

Output -

Output +

La page est en cours de chargement...

SolarEdge PB250-AOB Guide d'installation

Ce manuel convient également à

SolarEdge PB250-AOB Guide d'installation

dans d''autres langues

Autres documents