Extreme Networks 7520 Guide de référence

Marque: Extreme Networks

Modèle: 7520

Catégorie: Commutateurs réseau

Taper: Guide de référence

Extreme 7520 Series Quick

Reference

Follow these steps to get the switch ready for use.

For complete installation instructions see the Extreme 7520 Hardware

Installation Guide at www.extremenetworks.com/documentation/

Necessary Tools

• Appropriately grounded power receptacles

located within 1.8 m (6 ft.)

• A readily accessible device for disconnecting

power, such as a breaker or master switch

• Network cabling within reach

• Clearance of at least of 7.6 cm (3.0 in.) on all

sides for proper ventilation

• Temperature between 0°C (32°F) and 45°C

(113°F) -- or as noted in “Operating Temperature:” -- with fluctuations

of less than 10°C (18°F) per hour

If the switch appears to be damaged, contact Extreme Networks. See

“Getting Help” for more information.

Extreme Networks does not include power input cords with this product.

To purchase the correct power cord for your country, refer to

www.extremenetworks.com/product/powercords/.

1#2 Phillips screwdriver

(magnetic screwdriver recommended) 2ESD-protective wrist strap

1Prepare the Site

The installation site must meet the following requirements:

2Unpack the Box

Remove the packing material, and then verify that all of the

following components are included:

1Switch 4Mounting ears

24-post Rack Mount Kit 5Mounting ear screws

3Slider assembly 6Console cable

1Rack Mount Kit Quick Reference 3Screw sack

2Slide assemblies

Mount the 7520 switch in a standard equipment rack, in either of the

following ways:

• Four-post mount, using the mounting kit provided.

• Two-post mount, using mounting brackets (not provided) to attach

the front or the middle of the switch to the posts.

Four-Post Mount

1Separate the inner sliding rails from the outer rails by extending

the rails and pulling on the disconnect latch. Note which

direction the sliding rails slide from the outer rails for correct

installation.

2 Attach the outer rail to the rack, securing it with the M5 screws.

3 Attach an inner rail to the side of the unit, using the M4 screws. .

• If using the 1U long rack ears (already attached to the inner rail):

Ensure that the rack ear is flush with the either the front or the rear

panel of the unit and continue to step 4.

• If using the 1U or 2U short rack ears, attach one to the side of the unit

using the #6-32 screws, so that the rack ear is flush with either the

front or the rear panel of the unit.

4 Repeat steps 2 and 3 for the other side of the chassis.

5 Insert the chassis into the rail kit and secure it to the rack using the

thumb screws on the mounting ears.

Two-Post Mount

Note: The following diagram shows a mid-mounted configuration. The

brackets also support a front-mounted configuration.

1 Attach a mounting bracket to each side of the switch. You can attach

the brackets at the middle of the switch, as shown, or at the front

2 Secure the brackets to the rack posts using rack-mounting screws

that are appropriate for the rack (not provided).

3 Attach a mounting bracket to one side of the switch, so that its flange

(ear) aligns with the rack post. Then secure it to the rack post.

4 Attach a mounting bracket to the other side of the switch and then to

the rack post.

Connecting to the Primary Power Source

To attach the 7520 switch to a power source, do the following:

1 Connect the AC power cord to the AC power input socket on the

power supply and an AC power outlet.

2 When power is connected, verify that the switch’s PWR LED turns

green. If the PWR LED does not turn green, refer to the Extreme 7520

Hardware Installation Guide for troubleshooting information.

3Install the Switch

You can install any 7520 switch in a standard 19-inch

equipment rack.

5Connect Power

7520 switches run on AC or DC power. Connect the switch

to a primary power source.

Note: Installing the system as described in this guide meets the

protective earth grounding requirements of the National Electrical

Code (NEC) UL 60950 and IEC 60950 standards. However, in some

cases, it may be necessary to use an alternative grounding method.

In these cases, a 14 AWG wire can be connected between the

grounding lug on the chassis and a nearby building ground point.

To change the switch OS via the Bootloader Menu:

1 Connect the switch to a console with a baudrate of 115200.

2 When the switch is powered or reset, press the spacebar key within 30

seconds after seeing the “7520 Boot Menu” screen to activate the

Bootloader Menu.

3 Use the down-arrow key to select Change the switch OS to Fabric Engine,

then press Enter.

4 The switch will install Fabric Engine, then reset.

Safety Notices

Hardware Components

Figure 1 7520-48XT-6C and 7520-48Y-8C Switches: Front Panels

6Update and Configure the Switch

Upgrade to a generally available (GA) version of the

software before you use this unit. Switch Engine is the

default operating system (OS) for the 7520 Series. You can

change the switch OS from the Bootloader Menu on initial

activation only. See the Extreme 7520 Hardware Installation

Guide for all OS selection procedures.

Electrical Hazard: Only qualified instructed or skilled personnel should perform

installation, repair, or disassembly procedures.

Risques d’électrocution: Seul un personnel qualifié ou expérimenté peut

effectuer les procédures d'installation, de réparation ou de démontage.

Warning: Extreme Networks power supplies do not have switches for turning

the unit on and off. Before servicing, disconnect all power cords to remove

power from the device. Make sure that these connections are easily accessible.

Avertissement: Les alimentations d’Extreme Networks n’ont pas d’interrupteurs

pour allumer ou éteindre l'appareil. Avant l'entretien, débranchez tous les

cordons d'alimentation pour couper l'alimentation de l'appareil. Assurez-vous

que ces connexions sont facilement accessibles.

Warning: This equipment is designed for installation in restricted access

locations and suitable for installation in Information Technology Rooms in

accordance with Article 645 of the National Electrical Code and NFPA 75, not

suitable for use in locations where children are likely to be present.

Avertissement: Cet équipement est conçu pour être installé dans des endroits

à accès restreint et peut être installé dans des salles informatiques

conformément à l'article 645 du Code national de l'électricité et à la norme

NFPA 75, et ne peut être installé dans des endroits où des enfants sont

susceptibles d'être présents.

Warning: A dedicated Listed circuit breaker rated at 15A is to be used for each

power supply connection.

Avertissement: Un disjoncteur certifié 15A et dédié à l'installation doit être

utilisé pour chaque connexion d'alimentation.

Caution: Before mounting the device, ensure that the rack can support it

without compromising stability. Otherwise, personal injury or equipment

damage may result.

Caution: Follow appropriate ESD procedures when unpacking and handling

the switch. These include unpacking the switch in an ESD-safe environment

and wearing appropriate ESD protective gear, such as ESD-safe footwear and

ESD wrist straps where appropriate.

Caution: Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

Warning: Do not use optical instruments to view the laser output. The use of

optical instruments to view laser output increases eye hazard. Use only

UL/CSA, IEC/EN60825-1/-2 recognized pluggable modules.

Avertissement: Ne pas utiliser d'instruments optiques pour mesurer la

puissance laser. L'utilisation d’instruments optiques pour mesurer la puissance

laser peut augmenter les risques de dommages oculaires. Utilisez uniquement

des modules certifiés UL/CSA,

IEC/EN60825-1 /-2.

11/10/25G SFP28 ports for 7520-

48Y; 1G/10GBase-T RJ-45 ports

for 7520-48XT

4USB port

240/100Gbps QSFP28 ports 5Console port

3Management port 6System LEDs

Figure 2 7520-48XT-6C and 7520-48Y-8C Switches: Rear Panels

For component details, see the Extreme 7520 Hardware Installation

Guide.

Operating Conditions

Operating Temperature:

7520-48Y and 7520-48XT, AC/DC, front-to-back:

0°C (32°F) to 50°C (122°F) at sea level; 0°C (32°F) to 40°C (104°F) up to

3000 m (10,000 ft)

7520-48Y and 7520-48XT, AC/DC, back-to-front:

0°C (32°F) to 45°C (113°F) at sea level; 0°C (32°F) to 40°C (104°F) up to

3000 m (10,000 ft)

Storage Temperature:

-40°C to 70°C (-40°F to 158°F)

Operating Relative Humidity:

5% to 95% (non-condensing)

Interfaces

Each Extreme 7520 switch has an RJ-45 serial console port, a 10/100/

1000BASE-T out-of-band management port, and a USB Type A storage

port. A four-post rack mount kit (part no. XN-4P-RKMT298) is provided

with each switch. 7520 factory switches are pre-loaded with both Switch

Engine and Fabric Engine OSs.

The following table lists the specific interfaces for each switch.

Power Specifications

Power Supply and Fan Options

Available Rack-Mount Kits

1Grounding lug 3Fan modules

2Power supply slot(s)

7520-48Y-8C (base) 48 1/10/25Gbps SFP28 ports, 8 40/100Gbps QSFP28

ports, 2 empty power supply slots, 6 empty fan slots.

7520-48Y-8C-AC-F 48 1/10/25Gbps SFP28 ports, 8 40/100Gbps QSFP28

ports, dual AC power supplies, 6 fan units, front-to-

back airflow.

7520-48Y-8C-AC-R 48 1/10/25Gbps SFP28 ports, 8 40/100Gbps QSFP28

ports, dual AC power supplies, 6 fan units, back-to-

front airflow.

7520-48XT-6C (base) 48 1G/10GBase-T ports, 6 40/100Gbps QSFP28

ports, 2 empty power supply slots, 6 empty fan slots.

7520-48XT-6C-AC-F 48 1G/10GBase-T ports, 6 40/100Gbps QSFP28

ports, dual AC power supplies, 6 fan units, front-to-

back airflow.

7520-48XT-6C-AC-R 48 1G/10GBase-T ports, 6 40/100Gbps QSFP28

ports, dual AC power supplies, 6 fan units, back-to-

front airflow.

All models

AC Input: 100-120/200-240 VAC, 50/60 Hz, 3.5/1.8 A

Max. for each PSU

DC Input -48 VDC, 7.5A Max. for each PSU (Except for

China / 除中国地区)

XN-ACPWR-800W-F 800W AC power supply, Front-to-Back airflow

XN-ACPWR-800W-R 800W AC power supply, Back-to-Front airflow

XN-DCPWR-800W-F 800W DC power supply, Front-to-Back airflow

XN-DCPWR-800W-R 800W DC power supply, Back-to-Front airflow

XN-FAN-001-F Fan unit, Front-to-Back airflow

XN-FAN-001-R Fan unit, Back-to-Front airflow

XN-2P-RKMT299 Two-post rack mount kit for 7520 switches

XN-4P-RKMT298 Four-post rack mount kit for 7520 switches (included)

Getting Help

For additional support related to 7520 switches or this document, contact

Extreme Networks using one of the following methods:

Notice

Legal Notices

Extreme Networks, Inc. reserves the right to make changes in specifications

and other information contained in this document and its website without

prior notice. The reader should in all cases consult representatives of

Extreme Networks to determine whether any such changes have been

made.

The hardware, firmware, software or any specifications described or referred

to in this document are subject to change without notice.

Trademarks

Extreme Networks and the Extreme Networks logo are trademarks or

registered trademarks of Extreme Networks, Inc. in the United States and/or

other countries.

All other names (including any product names) mentioned in this document

are the property of their respective owners and may be trademarks or

registered trademarks of their respective companies/owners.

For additional information on Extreme Networks trademarks, please see:

www.extremenetworks.com/company/legal/trademarks/

Warranty

Warranty information for 7520 switches is located online at:

www.extremenetworks.com/support/policies/

Regulatory and Compliance Information

Federal Communications Commission (FCC) Notice

This device complies with Part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits

for a class A digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment uses, generates, and can radiate radio frequency energy and if

not installed in accordance with the operator’s manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause interference in which case the user will be

required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not

expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Industry Canada Notice

CAN ICES-3 (A)/NMB-3(A)

This digital apparatus does not exceed the class A limits for radio noise

emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de la class A

prescrites dans le Règlement sur le brouillage radioélectrique édicté par le

ministère des Communications du Canada.

Class A ITE Notice

WARNING: This equipment is compliant with Class A of CISPR 32. In a

residential environment this equipment may cause radio interference.

Product

Documentation

https://www.extremenetworks.com/documentation/

Global Technical

Assistance Center

(GTAC)

Phone: 1-800-998-2408 (toll-free in U.S. and Canada)

or +1-408-579-2826. For the support phone number in

your country, visit:

http://www.extremenetworks.com/support/contact/

GTAC Knowledge Get on-demand and tested resolutions from the GTAC

Knowledgebase, or create a help case if you need more

guidance.

Visit: https://gtacknowledge.extremenetworks.com/

The Hub A forum for Extreme customers to connect with one

another, get questions answered, share ideas and

feedback, and get problems solved. The community is

monitored by Extreme Networks employees, but is not

intended to replace specific guidance from GTAC.

Visit: https://community.extremenetworks.com

Support Portal Manage cases, downloads, service contracts, product

licensing, and training and certifications.

Visit: http://support.extremenetworks.com/

Product Safety

This product complies with the following international safety standards:

• UL 62368-1

• UL 60950-1

• CAN/CSA C22.2 No. 62368-1-14

• CAN/CSA C22.2 No. 60950-1-07

• IEC 62368-1

• IEC 60950-1

• EN 62368-1

• EN 60950-1

• 2014/35/EU

• CNS 15598-1

• GB 4943.1

Optical Module Compliance

Extreme Networks pluggable optical modules and direct-attach cables meet

the following regulatory requirements:

• UL and/or CSA registered component for North America

• Class 1 or Class 1M Laser Product

• FCC 21 CFR Chapter 1, Sub-chapter J in accordance with FDA & CDRH

requirements

• IEC/EN 60825-1:2007, IEC/EN 60825-2:2004+A1+A2 or later, European

Standard

Korea EMC Statement

Australia (RCM)

WARNING: This equipment is compliant with Class A of CISPR 32. In a

residential environment this equipment may cause radio interference.

Electromagnetic Compatibility (EMC)

This product complies with the following: FCC 47 CFR Part 15 Subpart B

Class A (US), ICES-003 (Canada), EN 55032 (ITE Emissions), EN 55035 (ITE

Immunity), EN 61000-3-2 (Harmonics), EN 61000-3-3 (Flicker), 2014/30/EU

(EMC Directive), EN 300 386 (Telecom), EN 55011 (ISM), EN 61000-6-2 (Ind.

Immunity), EN 61000-6-4 (Ind. Emissions), RCM (Australia), VCCI (Japan),

MSIP KCC (Korea), BSMI (Taiwan), ANATEL (Brazil), CQC (China)

VCCI Notice

This is a Class A product based on the standard of the Voluntary Control

Council for Interference by Information Technology Equipment (VCCI). If this

equipment is used in a domestic environment, radio disturbance may arise.

When such trouble occurs, the user may be required to take corrective

actions.

BSMI EMC Statement — Taiwan

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Battery Warning — Taiwan

Battery Notice

Hazardous Substances- China and Taiwan BSMI RoHS

Guidance concerning the China and Taiwan BSMI RoHS (Restriction of

Hazardous Substances) directive for this Extreme Networks® product can be

found on the following web page:

www.extremenetworks.com/support/documentation/restriction-hazardous-

substances/

The page contains tables detailing the presence of 10 substances defined by

the RoHS directive.

Hazardous Substances - EU

This product complies with the requirements of Directive 2011/65/EU of the

European Parliament and of the Council of 8 June 2011 on the restriction of

the use of certain hazardous substances in electrical and electronic

equipment.

European Waste Electrical and Electronic Equipment (WEEE)

Notice

In accordance with Directive 2012/19/EU of the European Parliament on

waste electrical and electronic equipment (WEEE):

1The symbol above indicates that separate collection of electrical and

electronic equipment is required.

2When this product has reached the end of its serviceable life, it cannot be

disposed of as unsorted municipal waste. It must be collected and treated

separately.

3It has been determined by the European Parliament that there are

potential negative effects on the environment and human health as a

result of the presence of hazardous substances in electrical and electronic

equipment.

4It is the users’ responsibility to utilize the available collection system to

ensure WEEE is properly treated.

For information about the available collection system, please contact

Extreme Customer Support at +353 61 705500 (Ireland).

Warning: This product contains a battery used to maintain product

information. If the battery should need replacement it must be

replaced by Service Personnel. Please contact Technical Support for

assistance.

Risk of explosion if battery is replaced by an incorrect type. Dispose

of expended battery in accordance with local disposal regulations.

Avertissement: Ce produit renferme une pile servant à conserver les

renseignements sur le produit. Le cas échéant, faites remplacer la

pile par le personnel du service de réparation. Veuillez communiquer

avec l’assistance technique pour du soutien.

Il y a risque d’explosion si la pile est remplacée par un type de pile

incorrect. Éliminez les piles usées en conformité aux règlements

locaux d'élimination des piles.

Extreme Networks

Extreme 7520 Series

Quick Reference

7520-48Y-8C

7520-48XT-6C

Read Me First - Switch OS Selection

Scan for instructions to choose your preferred Switch OS on the Universal Switch.

P/N 9037254-00 Rev. AD

Extreme Networks 7520 Guide de référence

Marque: Extreme Networks

Modèle: 7520

Catégorie: Commutateurs réseau

Taper: Guide de référence

Télécharger le PDF

rapport

dans d''autres langues

English: Extreme Networks 7520 Reference guide

Documents connexes

Extreme Networks Industrial Switches Guide de référence

Extreme Networks 7520 Guide de référence

Extreme Networks 7520 Guide de référence

dans d''autres langues

Documents connexes

Autres documents