Extreme Networks Industrial Switches Guide de référence

Marque: Extreme Networks

Modèle: Industrial Switches

Taper: Guide de référence

Industrial Switch Series

Quick Reference

Follow these steps to get the switch ready for use.

For complete installation instructions see the ISW Hardware Installation

& User Guide at www.extremenetworks.com/documentation

Necessary Tools

• Appropriately grounded power receptacles

located within 1.8 m (6 ft.).

• A readily accessible device for disconnecting

power, such as a breaker or primary switch.

• Network cabling within reach.

• Up to at least 7.6 cm (3.0 in.) on all sides, for

proper ventilation.

• Temperature between -40°C (-40°F) and

75°C (167°F) -- or as noted in “Operating Temperature:”-- with

fluctuations of less than 10°C (18°F) per hour.

If the switch appears to be damaged, contact Extreme Networks. See

“Getting Help” for more information.

Extreme Networks does not include power input cords with this product.

To purchase the correct power cord for your country, refer to

http://www.extremenetworks.com/product/powercords/.

DIN-Rail Mount

1 Screw the DIN-Rail bracket on with the bracket and screws in the

accessory kit.

2 Hook the unit over the DIN rail.

3 Push the bottom of the unit towards the DIN Rail until it snaps into

place.

1#2 Phillips screwdriver

(magnetic screwdriver recommended) 2ESD-protective wrist strap

1Prepare the Site

The installation site must meet the following requirements:

2Unpack the Box

Remove the packing material, and verify that all of the

following components are included:

DIN-Rail/Wall Mount Rack Mount

Management Ethernet switch 1 1

Wall-mount plates 2 n/a

DIN-RAIL clip 1 n/a

19” Rack mount brackets n/a 2

M3 Screws (for the wall mount plates

& DIN-RAIL clip or rack mount) 4 8

DC power terminal block 1 1

Console cable 1 1

QRG (this document) 1 1

RJ45 Ethernet port

Dust Cover SFP Ethernet port

Dust Cover Earth Ground

Screw

ISW-4W-4WS-4X 8 8 M4

ISW-24W-4X 24 4 M4

16801 3 2 M3

16802 4 4 M3

16803 3 2 M3

16804 4 4 M3

3Install the Industrial Switch Series switch

The 8-port and 12-port switch models can only be DIN-Rail

mounted or wall mounted.

Note: The ISW-24W-4X switch can be installed in a standard

two-post equipment rack. It does not support Din Rail or

Wall Mount options.

Wall Mount

Attach the wall-mounting plates with the screws provided in the

accessory kit.

Note: Wall anchors and wood screws are not provided.

Two-Post Mount

This procedure uses the two-post mounting kit.

1 Attach a rack ear to one side of the switch, screwing it into the holes

so that the flange (ear) is flush with the front of the switch.

2 Attach the other rack ear to the other side.

3 Attach the rack ears to the front rack posts, using the screws (rack

post screws not provided).

Connect to the primary power source

To attach your switch to a power source, do the following:

1 Verify that the power source circuit is de-energized.

2 Connect the DC outlets on the power supply to the DC power inlets

on the rear or the top of the switch.

3 Connect the AC power inlets on the power supply to the AC power

source.

4 Energize the circuit.

5 When power is connected, verify that the switch’s PWR LED turns

green. If the PWR LED does not turn green, refer to ISW Series

Hardware Installation Guide for troubleshooting information.

4Connect Power

Extreme Networks Industrial Switches support dual DC power

input. Extreme Networks also offers power supplies that

accept AC input and provide DC output for use by the

switches. Refer to the Hardware Install & User Guide for more

information on DC input rating of the Switches, and the AC

Input and DC Output rating of the power supplies.

Note: Installing the system as described in this guide meets the

protective earth grounding requirements of the National

Electrical Code (NEC), UL/CSA/IEC/EN 60950-1/UL/CSA/IEC/

EN -62368-1 standards. Ensure that the provided earth ground

screw (either M4 or M3) on the system is used to connect to an

earth ground using the green-and-yellow 16 AWG ground wire.

Note: The power supplies must be installed by qualified

personnel such as licensed electricians, in accordance with local

electrical codes, and connected to a well fused power source.

5Update and Configure the Switch

Upgrade to a generally available (GA) version of the

software before you use this unit. For more information,

see ISW Hardware Installation & User Guide.

Safety Notices

Hardware Components

Figure 1 Industrial Series: 12-Port PoE Series Front Panel

Figure 2 Industrial Series: 12-Port PoE Series Top Panel

Figure 3 Industrial Switch Series: 28-Port PoE Series Front Panel

Electrical Hazard: Only qualified instructed or skilled personnel should perform

installation, repair, or disassembly procedures.

Risques d’électrocution: Seul un personnel qualifié ou expérimenté peut

effectuer les procédures d'installation, de réparation ou de démontage.

Warning: Extreme Networks power supplies do not have switches for turning

the unit on and off. Before servicing, disconnect all power cords to remove

power from the device. Make sure that these connections are easily accessible.

Avertissement: Les alimentations d’Extreme Networks n’ont pas d’interrupteurs

pour allumer ou éteindre l'appareil. Avant l'entretien, débranchez tous les

cordons d'alimentation pour couper l'alimentation de l'appareil. Assurez-vous

que ces connexions sont facilement accessibles.

Warning: This equipment is designed for installation in restricted access

locations and suitable for installation in Information Technology Rooms in

accordance with Article 645 of the National Electrical Code and NFPA 75, not

suitable for use in locations where children are likely to be present.

Avertissement: Cet équipement est conçu pour être installé dans des endroits

à accès restreint et peut être installé dans des salles informatiques

conformément à l'article 645 du Code national de l'électricité et à la norme

NFPA 75, et ne peut être installé dans des endroits où des enfants sont

susceptibles d'être présents.

Warning: A dedicated Listed circuit breaker rated at 15A is to be used for each

power supply connection.

Avertissement: Un disjoncteur certifié 15A et dédié à l'installation doit être

utilisé pour chaque connexion d'alimentation.

Caution: Before mounting the device, ensure that the rack can support it

without compromising stability. Otherwise, personal injury or equipment

damage may result.

Caution: Follow appropriate ESD procedures when unpacking and handling

the switch. These include unpacking the switch in an ESD-safe environment

and wearing appropriate ESD protective gear, such as ESD-safe footwear and

ESD wrist straps where appropriate.

Caution: Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

Warning: Do not use optical instruments to view the laser output. The use of

optical instruments to view laser output increases eye hazard. Use only

UL/CSA, IEC/EN60825-1/-2 recognized pluggable modules.

Avertissement: Ne pas utiliser d'instruments optiques pour mesurer la

puissance laser. L'utilisation d’instruments optiques pour mesurer la puissance

laser peut augmenter les risques de dommages oculaires. Utilisez uniquement

des modules certifiés UL/CSA,

IEC/EN60825-1 /-2.

1Combo ports:

10/100/1000BASE-T 90W 802.3bt

PoE ports or 1000BASE-X (SFP)

ports

210GBASE-X SFP+ ports

3System status LEDs

4Device info/status

510/100/1000BASE-T 90W PoE

802.3bt ports

6Port LEDs

7USB Type A port

1Dual power input (6p terminal

block)

2RJ45 serial console port

3Reset

4Grounding lug

1USB Type A port 5Device info/status

210/100/1000BASE-T OOB management

port 6System status LEDs

Figure 4 Industrial Series: 28-Port PoE Series Rear Panel

Figure 5 Industrial Switch Series: 8-Port PoE Series Front Panels

Figure 6 Industrial Switch Series: 12-Port PoE Series Front Panels

Figure 7 Industrial Switch Series: Top Panel of All 8-Port and 12-Port

Models

For component details, see ISW Hardware Installation & User Guide.

Operating Conditions

Operating Temperature:

-40°C (-40°F) to 75°C (167°F)

Temperature restrictions might apply. See ISW Series Hardware

Installation Guide for details.

Storage Temperature:

-40°C to 85°C (-40°F to 185°F)

Operating Relative Humidity:

5% to 95% (non-condensing)

310/100/1000Base-T PoE 802.3bt ports 7RJ-45 serial console port

4SFP+ ports (1/2.5/10G) 8Reset

1Dual power input (4p terminal block) 2Grounding lug

1PoE LEDs

2System status LEDs

310/100 Ethernet Copper Ports

4Gigabit Ethernet SFP Ports

5Device info/status

6Gigabit Ethernet SFP ports

7Gigabit Ethernet Copper Ports

1PoE LEDs

2System status LEDs

310/100 Ethernet Copper Ports

4Gigabit Ethernet SFP ports

5Device info/status

6Gigabit Ethernet Copper Ports

1Dual power input (6p terminal

block)

2RJ45 serial console port

3Reset

4Grounding lug

Note: The operating temperature range is -40°C (-40°F) to

59°C (138°F) when using the IS AC-DC PS 240W power supply

with the ISW-4W-4WS-4X and ISW-24W-4X switch models.

Interfaces

Each Industrial Switch Series switch includes an RJ-45 serial console

port, dual DC power inputs for redundancy and reverse power

protection, fanless cooling, and PoE ports that are 802.3af, 802.3at and

802.bt compliant with support for up to 90W.

The following table lists the specific interfaces for each switch.

Power Supply and Rail-Kit Options

Getting Help

For additional support related to Industrial Switch Series switches or this

document, contact Extreme Networks using one of the following methods:

Notice

Legal Notices

Extreme Networks, Inc. reserves the right to make changes in specifications

and other information contained in this document and its website without

prior notice. The reader should in all cases consult representatives of

Extreme Networks to determine whether any such changes have been

made.

The hardware, firmware, software or any specifications described or referred

to in this document are subject to change without notice.

Trademarks

Extreme Networks and the Extreme Networks logo are trademarks or

registered trademarks of Extreme Networks, Inc. in the United States and/or

other countries.

All other names (including any product names) mentioned in this document

are the property of their respective owners and may be trademarks or

registered trademarks of their respective companies/owners.

For additional information on Extreme Networks trademarks, please see:

https://www.extremenetworks.com/company/legal/trademarks/

Warranty

Warranty information for Industrial Switch Series is located online at:

https://www.extremenetworks.com/support/policies/

ISW-12 802.3bt 4GbP 4

Combo 4 SFP+

(ISW-4W-4WS-4X)

(12-Port model): 4 10/100/1000Base-T 90W 802.3bt

ports, 4 combo ports supporting either 4 10/100/

1000Base-T 90W PoE OR 4 1000Base-X (SFP), plus 4

10GBase-X SFP+ ports dual DC power inputs, fanless

ISW-28 802.3bt 24GbP

4 SFP+ 1RU

(ISW-24W-4X)

(28-Port model): ISW Industrial Ethernet Switch 24 10/

100/1000Base-T 90W PoE 802.3bt ports, plus 4

10GBase-X SFP+ ports dual DC power inputs, fanless,

1RU

ISW 4-10/100P, 2-10/

100T, 2-SFP

(16801)

(8-Port model): 4-Port PoE+ 10/100 2-Port 10/100 w/2-

Port SFP dual DC power inputs, fanless

ISW 8-10/100P, 4-SFP

(16802) (12-Port model): 8-Port PoE+ 10/100 w/ 4-Port SFP

dual DC power inputs, fanless

ISW 4GbP, 2GbT, 2-SFP

(16803) (8-Port model): 4-Port PoE + Gigabit, 2-Port Gigabit w/

2-Port SFP dual DC power inputs, fanless

ISW 8 GbP, 4-SFP

(16804) (12-Port model): 8-Port PoE+ Gigabit w/ 4-Port SFP

dual DC power inputs, fanless

IS AC-DC PS 240W

(16807) IS AC-DC Power Supply 240W Output DIN Rail

IS AC-DC PS 480W

(16920) IS AC-DC Power Supply 480W Output DIN Rail

ISW AC-DC PS 960W DIN

Rail

(ISW-AC-DC-PS-960W)

ISW AC-DC Power Supply 960W Output DIN Rail

Product

Documentation

View hardware and software documentation for

products on the website at:

https://www.extremenetworks.com/documentation/

From this page, you can view and download hardware

installation guides, software release notes, compatibility

matrices, software license information, and other

documents.

Global Technical

Assistance Center

(GTAC)

Phone: 1-800-998-2408 (toll-free in U.S. and Canada) or

+1-408-579-2826. For the support phone number in your

country, visit:

http://www.extremenetworks.com/support/contact/

GTAC Knowledge Get on-demand and tested resolutions from the GTAC

Knowledgebase, or create a help case if you need more

guidance.

Visit: https://gtacknowledge.extremenetworks.com/

The Hub A forum for Extreme customers to connect with one

another, get questions answered, share ideas and

feedback, and get problems solved. The community is

monitored by Extreme Networks employees, but is not

intended to replace specific guidance from GTAC.

Visit: https://community.extremenetworks.com

Support Portal Manage cases, downloads, service contracts, product

licensing, and training and certifications.

Visit: http://support.extremenetworks.com/

To request an Extreme Portal account, use the Log in or

home page and click Create a new Extreme Portal

account.

Regulatory and Compliance Information

Federal Communications Commission (FCC) Notice

This device complies with Part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits

for a class A digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment uses, generates, and can radiate radio frequency energy and if

not installed in accordance with the operator’s manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause interference in which case the user will be

required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not

expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Industry Canada Notice

CAN ICES-3 (A)/NMB-3(A)

This digital apparatus does not exceed the class A limits for radio noise

emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de la class A

prescrites dans le Règlement sur le brouillage radioélectrique dicté par le

Ministère des Communications du Canada.

Class A ITE Notice

WARNING: This equipment is compliant with Class A of CISPR 32. In a

residential environment this equipment may cause radio interference.

Product Safety

This product complies with the following international safety standards:

• UL 62368-1

• UL 60950-1

• CAN/CSA C22.2 No. 62368-1-14

• CAN/CSA C22.2 No. 60950-1-07

• IEC 62368-1

• IEC 60950-1

• EN 62368-1

• EN 60950-1

• 2014/35/EU

• CNS 14336-1

• GB 4943.1

Optical Module Compliance

Extreme Networks pluggable optical modules and direct-attach cables meet

the following regulatory requirements:

• UL and/or CSA registered component for North America

• Class 1 or Class 1M Laser Product

• FCC 21 CFR Chapter 1, Sub-chapter J in accordance with FDA & CDRH

requirements

• IEC/EN 60825-1, IEC/EN 60825-2 or later, European Standard

Korea EMC Statement

Australia (RCM)/European Union (CE)/United Kingdom (UKCA)

WARNING: This equipment is compliant with Class A of CISPR 32. In a

residential environment this equipment may cause radio interference.

Electromagnetic Compatibility (EMC)

This product complies with the following: FCC 47 CFR Part 15 Subpart B

Class A (US), ICES-003 (Canada), EN 55032 (ITE Emissions), EN 55035 (ITE

Immunity), EN 61000-3-2 (Harmonics), EN 61000-3-3 (Flicker), 2014/30/EU

(EMC Directive), Electromagnetic Compatibility Regulations 2016 (S.I. 2016/

1091), EN 300 386 (Telecom), EN 55011 (ISM), EN 61000-6-2 (Ind. Immunity),

EN 61000-6-4 (Ind. Emissions), RCM (Australia), VCCI (Japan), MSIP KCC

(Korea), BSMI (Taiwan), ANATEL (Brazil), and CCC (China).

VCCI Notice

This is a Class A product based on the standard of the Voluntary Control

Council for Interference by Information Technology Equipment (VCCI). If this

equipment is used in a domestic environment, radio disturbance may arise.

When such trouble occurs, the user may be required to take corrective

actions.

BSMI EMC Statement — Taiwan

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Hazardous Substances- China and Taiwan BSMI RoHS

Guidance concerning the China and Taiwan BSMI RoHS (Restriction of

Hazardous Substances) directive for this Extreme Networks® product can be

found on the following web page:

https://www.extremenetworks.com/support/documentation/restriction-

hazardous-substances/

The page contains tables detailing the presence of 10 substances defined by

the RoHS directive.

Hazardous Substances - EU

This product complies with the requirements of Directive 2011/65/EU of the

European Parliament and of the Council of 8 June 2011 on the restriction of

the use of certain hazardous substances in electrical and electronic

equipment.

European Waste Electrical and Electronic Equipment (WEEE)

Notice

In accordance with Directive 2012/19/EU of the European Parliament on

waste electrical and electronic equipment (WEEE):

1The symbol above indicates that separate collection of electrical and

electronic equipment is required.

2When this product has reached the end of its serviceable life, it cannot be

disposed of as unsorted municipal waste. It must be collected and treated

separately.

3It has been determined by the European Parliament that there are

potential negative effects on the environment and human health as a

result of the presence of hazardous substances in electrical and electronic

equipment.

4It is the users’ responsibility to utilize the available collection system to

ensure WEEE is properly treated.

For information about the available collection system, please contact

Extreme Customer Support at +353 61 705500 (Ireland).

Extreme Networks

Industrial Switch Series

Quick Reference

ISW-4W-4WS-4X

ISW-24W-4X

16801

16802

16803

16804

P/N 9037597-00 Rev. AE

Extreme Networks Industrial Switches Guide de référence

Marque: Extreme Networks

Modèle: Industrial Switches

Taper: Guide de référence

Télécharger le PDF

rapport

dans d''autres langues

English: Extreme Networks Industrial Switches Reference guide

Documents connexes

Extreme Networks 7520 Guide de référence

Extreme Networks Industrial Switches Guide de référence

Extreme Networks Industrial Switches Guide de référence

dans d''autres langues

Documents connexes

Autres documents