Graymills Solvent Handi-Kleen PL364 PL424 -1204 Le manuel du propriétaire

795-93851 1 of 48 12/23/21

HANDI-KLEEN® PARTS CLEANER – SOLVENT

Models PL364, PL424

Operations and Maintenance Instructions

Graymills Corporation

2601 S. 25th Ave., Broadview, IL 60155

www.graymills.com

795-93851 2 of 48 12/23/21

SHIPPING INFO

Unpacking and Inspection

You should inspect your equipment for possible shipping damage.

Thoroughly check the equipment for any damage that might have occurred in transit, such as broken or

loose wiring and components, loose hardware, and mounting screws, etc.

In the Event of Shipping Damage

According to the contract terms and conditions of the Carrier, the responsibility of the Shipper ends at

the time and placement of shipment.

Notify the transportation company’s local agent if you discover damage.

Hold the damaged goods and packing material for the examining agent’s inspection. Do not return any

goods before the transportation company’s inspection and authorization.

File a claim with the transportation company. Substantiate the claim by referring to the agent’s report. A

certified copy of our invoice is available upon request. The original Bill of Lading is attached to our original

invoice. If the shipment was prepaid, write us for a receipted transportation bill.

Advise customer service regarding your wish for assistance and obtain an RMA (return material

authorization) number.

If the Shipment is Not Complete

Check the packing list as back-ordered items are noted on the packing list. You should have:

• Bill of lading

• Packing list

• User’s Manual

Re-inspect the container and packing material to see if you missed any smaller items during unpacking.

If the Shipment is not Correct

If the shipment is not what you ordered, contact the parts and service department immediately. Have the

order number and item number available. Hold the items until you receive shipping instructions.

Returns

Do not return any damaged or incorrect items until you receive shipping instructions from the customer

service department.

795-93851 3 of 48 12/23/21

INTRODUCTION

The Handi-Kleen parts cleaner is an economical and effective parts cleaner. Parts are scrubbed by a

hand-held brush (see ACCESSORIES section) under a flex hose, resting on a removable metal shelf

above fluid level or may be soaked in solvent below the shelf. Cleaning fluid is circulated through a sludge

basket with foam filters to trap finer particles.

PL364 PL424

Standard Features

• Flexible Stay-Put metal flush hose for directable hands-free flushing action

• 16-gauge minimum steel tank leak tested for 24 hours after welding with powder-coat finish for

durability and long-life

• Fusible safety link closes lid in event of fire

• Bottom drain convenient for fluid change-outs

• Small parts basket

• Removable work shelf for parts cleaning above fluid or soaking in solvent tank

• Filter and sludge collector basket

• Freeboard compliant (only when removable shelf is installed)

• 400 GPH Graymills Superflo™ pump

795-93851 4 of 48 12/23/21

SAFETY WARNINGS / CAUTIONS

Read all the SAFETY INSTRUCTIONS on the machine and those in the manual BEFORE installing

or using this equipment. Keep this manual handy for reference/training.

You will find various types of safety information on the following pages and on the labels attached to

Graymills equipment. The following Safety Statements explain their meaning.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey

all safety messages that follow this symbol to avoid personal injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTION, used with the safety alert symbol, indicates a hazardous situation which,

if not avoided, could result in minor or moderate injury.

CAUTION, without the safety alert symbol, is used to address practices not related

to personal injury.

Read and understand the user manual before operating this unit.

Do not operate above 100°F (38°C) maximum ambient temperature, near open flames, sparks, or

smoking materials. Keep cover closed when unattended.

To provide continued protection against risk of electrical shock, fire, and explosion, connect to

properly grounded supply or outlets only.

Risk of explosion. This equipment has internal arcing and sparking parts, which shall not be

exposed to flammable vapors. This equipment shall not be located in a recessed floor are or below

grade.

Only cleaning fluids with a flash point at or above 104°F (40°C) shall be used. Refer to user manual

for a list of solvents which have been evaluated for use.

Do NOT contaminate cleaning solution with fluids below 104°F (40°C) flash point including

gasoline, alcohol, or other flammable liquids. Even small amounts will create a hazardous

condition.

Ensure fusible link and closing device are in proper working order. Fusible link melts at

165°F(74°C) causing lid to close. When open the lid must lean forward so it will close automatically

when link melts. Do NOT tamper with or remove the fusible safety link. If the safety link breaks or

is lost, do NOT use the unit. Replace the safety link immediately.

Hazardous voltage present. Disconnect power before repairing or cleaning. Unit must be properly

grounded to prevent electric shock, fire, and explosion hazard. Connect only to three prong outlets.

Should cord become cracked, frayed, or damaged in any way, it should be repaired immediately

by a qualified electrician. Never use an extension cord. Since operator safety at all times is a

priority, we strongly recommend that, whether or not required by local code, this equipment be

connected only into a power supply equipped with a “Ground Fault Interrupter” (GFI). All electrical

connections should conform to national/local codes and be made by qualified personnel.

Do not leave objects in the tank or let hose attachments exit the tank which prevent lid from closing

completely in the event of fire.

Do not operate below minimum liquid level marking. Low liquid level may result in motor failure,

creating a potential fire hazard. Fill tank to recommended operating capacity range before plugging

795-93851 5 of 48 12/23/21

in power cord Do not operate with tank empty.

Operator shall wear appropriate PPE (personal protective equipment). Refer to cleaning fluid SDS

(safety data sheet) for details. If any cleaning solutions are splashed on clothing, remove wet

clothing promptly and thoroughly wash body areas that have been in contact with the solution. Do

NOT permit saturated clothing to remain in contact with skin. Cleaning solutions may irritate skin

and eyes. If splashed in eyes, flush thoroughly with water. Consult Safety Data Sheet (SDS) and a

physician. Always wear appropriate safety items such as gloves, apron, safety glasses or goggles.

Floor may be slippery when wet, do not splash fluids out of tank.

Use with solvent cleaning fluids only. The use of aqueous based (water) cleaning fluids will damage

the finish and cause rusting.

Install unit on level surface. Do not overload tank floor, shelf, or trays. Load items evenly, do not

allow items to overhang outside tank.

Never work with equipment you feel may be unsafe. Contact your supervisor immediately if you

feel a piece of equipment is in an unsafe condition.

SPECIFICATIONS AND DIMENSIONS

Depending on the model, the Handi-Kleen parts cleaner operates at either 115V or 230V or can be

powered by an air motor. To determine the electrical requirements of your model, check the nameplate

located on the side of the tank near the motor. An “A” designation after the model number indicates it

operates at 115V, 60 Hz, 1 ph. A “B” following the model number means the unit is rated at 230V, 60 Hz,

1 ph. Air powered units are designated with a -GAM suffix.

The Handi-Kleen is designed to be used with combustible (flash point over 104°F) petroleum-based

cleaning fluids such as Regular Agitene® 141 or Super Agitene® 141. Super Agitene® 141 has a mild,

fresh odor and is far superior in cleaning ability than normal safety solvents. Super Agitene® 141 also

contains “HandEase,” a lanolin formulation that helps prevent skin irritation, plus seven other ingredients

that make it a unique cleaning fluid that cleans faster, more easily and lasts longer than other cleaning

fluids. Super Agitene® 141 also leaves a light rust retarding film. Regular Agitene® 141 is a fast-drying,

film-free cleaner which contains Tergene, a detergent additive for better cleaning efficiency. It is especially

recommended for cleaning electrical parts and parts to be painted since it will not harm varnish or leave

behind any film.

795-93851 6 of 48 12/23/21

INSTALLATION AND OPERATION

The work area should be well ventilated.

Provide adequate lighting in the work area to allow observation of the cleaning process and the floor area

around the machine. Be sure to allow adequate room to bring work to and from the machine. Provide

sufficient clearance around the machine for fluid changeovers and servicing.

Site Preparation

Before installing, careful consideration should be given to the place of operation. Place unit on a smooth,

level surface. To the extent possible avoid installing machine in areas subject to high forklift traffic.

Reasonable precautions shall be taken to avoid damaging the legs and tank walls.

MODEL

A

B

C

D

E

F

G

MAX

MIN

PL364

36’’

22’’

60.5’’

28’’

21’’

16.25’’

39’’

4.5”

2.5’’

PL424

42’’

38''

20.25”

8”

4.5”

MODEL NO.

FLUID CAPACITY

MAX LOAD CAPACITY - SHELF/FLOOR

PL364

5-15 GAL

100/300 LBS

PL424

18-34 GAL

795-93851 7 of 48 12/23/21

Assembly

After removing the Handi-Kleen from its shipping carton remove any shelves or loose internal parts from

the tank (FIGURE 1(A)) and place tank on its side and assemble legs (FIGURE 1(B)) on the outside of

tank brackets (if placed on inside of brackets, holes will not align). It is recommended that the flattened

shipping carton be placed under the tank while assembling the legs to avoid scratching the paint and that

a minimum of two assemblers be employed for this task. Securely tighten all 16 screws (FIGURE 1(C))

into the weldnuts on the tank making sure to include all flat washers (FIGURE 1(D)). [On PL424 there is

only one set of legs. One leg runs the full width of the tank at each end.] Turn unit upright. Install the Handi-

Kleen in a convenient location close to an electrical outlet or compressed air supply, away from open

flame or sparks. Check and tighten all fittings before filling with solvent. Liquid level should remain under

the high-level line. Do NOT overfill. Keep cover closed when not in use to reduce evaporation of cleaning

fluid. The reflective white cover aids visibility when open.

FIGURE 1

Automatic Safety Cover

Open the automatic Safety Cover (FIGURE 2(E)) on your Handi-Kleen and you will notice that it lifts

simply and easily with one hand. There is nothing to connect or disconnect to open or close the cover.

Your Handi-Kleen cover is equipped with a two-way gas spring (FIGURE 2(L)) that also incorporates a

fusible link (FIGURE 2(G)). When open, the cover mechanism supports the cover at a slightly forward

angle. This angle is necessary to assure the cover’s fusible link will operate in the unlikely event of fire in

the tank. In the event of a fire, the fusible link will melt at 165°F permitting the lid to slam shut, reducing

oxygen supply to the fire.

REF.

DESCRIPTION

QTY.

A

TANK ASSEMBLY

1

B

LEG EXTENSION

4

C

M/S RD HD 10-32 X 1/2

16

D

FLAT WASHER #10

12

795-93851 8 of 48 12/23/21

FIGURE 2

Never leave the Handi-Kleen unattended with parts in the tank which would prevent the cover from closing

completely in the event of a fire. Always make sure that the cover remains in its correct, slightly tilted

forward position when open. Do NOT tamper with or remove the fusible safety link. If the safety link

breaks or is lost, replace immediately. Keep the cover closed when the unit is not being used.

Filter Baskets

The filter basket (FIGURE 2(N)) rests on the tank floor for the PL364 and hooks to the back of the tank on

the PL424, underneath the work shelf and is easily removed for cleaning. Solvent flows from the flex hose

(FIGURE 2(O)) onto the work shelf and drains through slots in the back of the work shelf into the filter

basket located at the middle rear of the tank. Heavy soils will drop to the bottom of the rectangular container.

Solvent will then flow through the filter pad (FIGURE 2(M)) and back into the tank.

Keeping the filter basket clean will prolong solvent life.

Work Shelves and Parts Baskets

Position the work shelf support legs to the rear of the unit; the filter is in between the legs. Hook the parts

basket on the right side of tank in front of pump.

COMP.

REF.

DESCRIPTION

E

LID WELDMENT ASSY.

F

STUD, GAS SHOCK

G

FUSE LINK ASSY. SOLDERED (TYPE K)

H

NUT, CAP PUSH 5/16"

J

C/S,HEX,HD,1/4-20 X 5/8

K

SLEEVE 5/16OD X 1/4ID X 5/16LG

L

GAS

SPRING,PL36/PL422/PL424/C.O.M.

M

FILTER

N

FILTER BASKET

O

FLEX HOSE 1/4" NPT Stl. 30"

P

PIPE,PLUG 3/4NPS-POLY,GASKET

795-93851 9 of 48 12/23/21

Handi-Kleen Pumps

The pumping unit is a valuable aid in parts cleaning. It is particularly useful for flushing away softened

grease and grime as you brush the parts. Graymills VP Series pumps, which are designed into the Handi-

Kleen models, are of a centrifugal type with bottom intake and operate at low pressure to aid against splash.

These pumps are made of high strength, reinforced thermoplastic.

Make sure the wire mesh screen is in position, protecting pump intake.

Handi-Kleen Motors

Handi-Kleens are equipped with either an air or electric motor, depending on your model. Electric motors

should have the same cycle, phase, and voltage as the electric power available. Electric motors require no

lubrication. However, motor ventilating openings should not be closed off or blocked in any way. Air motors

require clean compressed air with some oil mist mixed by an air filter lubricator (FRL-1) connected near the

motor.

The flexible hose is capable of splashing solvent and/or ejecting it from the machine. The hose must be

directed into the tank at all times and eye protection worn while operating the equipment.

All models:

• Never work with equipment you feel may be unsafe. Contact your supervisor immediately if you

feel a piece of equipment is in an unsafe condition.

• Fill tank with Graymills Regular Agitene® 141/Super Agitene® 141 or comparable cleaning fluid

with a flash point of 104°F (40°C) or higher.

• Insert plug into a properly grounded compatible outlet. For air-powered units the tank should be

connected to ground to dissipate static electricity.

• Turn on rocker switch on right side of tank to start fluid recirculating.

795-93851 10 of 48 12/23/21

MAINTENANCE

Cleaning

To maximize fluid life, sludge collector basket (FIGURE 2(N)) and foam filter blocks (FIGURE 2(M))

should be cleaned regularly. At least once a week, lift out, drain sludge, and rinse filter element.

Changing Fluid

• Remove the flexible hose (FIGURE 2(O)) from the "L" support bracket, aim it over the tank sides

into a proper container and remove all but the last 1” of solvent using the pump.

• Open the drain (FIGURE 2(P)) located in the center of the tank bottom to allow the remaining

sludge to drain into a dirty pail.

• Wipe the tank clean when empty. Rinse the part basket, replace the drain plug, and refill the tank.

The cleaning process normally takes 10 - 15 minutes.

• Always dispose of used cleaning fluid properly. Refer to the cleaning chemical SDS (safety data

sheet) and manufacturer's package label for instructions.

If your model is equipped with external filters, they can be removed simply be unscrewing them from the

manifold. See REPLACEMENT PARTS section for more information on replacement filter part numbers.

795-93851 11 of 48 12/23/21

Pump Service

Decreased solvent flow from the nozzle could mean not enough solvent is getting to the pump, indicating

a sludge build-up at the pump intake area. Clean pump screen weekly for best operation, more often in

heavy use.

To remove the pumping unit from the Handi-Kleen, perform the following procedures:

• Disconnect the Handi-Kleen from the power or air source.

• Remove the motor cover by unscrewing all machine screws. Remove four machine screws on

motor/filter shelf to free up pump shelf assembly.

• Remove the flexible hose from the "L" support bracket

• Detach ground wire from ground stud on tank

• Lift pump out of compartment and check bottom of pump compartment for sludge.

• If it is necessary to clean the pump interior, remove the bottom screws, plate and gasket. Unscrew the

set- screw in the impeller and lift it with the help of two small screwdrivers.

• Rinse and reassemble the pump.

TROUBLESHOOTING GUIDE

CONDITION

POSSIBLE CAUSE

CORRECTION

Pump

Pump does not run

(-A and -B units)

Machine is unplugged

Plug machine into outlet

Circuit breaker is tripped

Check breaker and correct.

If problems persist, contact

Graymills.

Pump motor is burned out

Replace pump

Pump does not run

(-GAM units)

Insufficient air pressure

Ensure air pressure is set to

60 psi min

Air motor vanes seized

Inject 5 drops #10 oil into air

motor inlet

Pump runs but does not

pump fluid

(ALL units)

Pump filter screen is clogged

Clear debris from around

pump

Flexible metal hose clogged

Clear debris from metal

hose

Pump rubber discharge hose

clogged

Clear debris from hose or

replace hose

Pump runs but does not

pump fluid (external filter

units)

External filter is clogged

Replace external filters

Pump runs but is noisy

(Some noise is normal).

Cavitation due to low liquid

level

Raise liquid level to correct

level

795-93851 12 of 48 12/23/21

REPLACEMENT PARTS

ITEM

NO.

PART NUMBER

DESCRIPTION

1

597-36908-86

STUD, GAS SHOCK

2

740-93713

FUSE LINK 165F

3

755-90109-11

NUT, CAP PUSH 5/16"

4

752-90405-81

C/S,HEX,HD,1/4-20 X 5/8

5

760-23677

SLEEVE 5/16OD X 1/4ID X 5/16LG

6

765-09853

GAS

SPRING,PL36/PL422/PL424/C.O.M.

7

742-07095

FILTER

8

645-35265 PL364

645-44865 PL424

FILTER BASKET

9

728-20552

FLEX HOSE 1/4" NPT Stl. 30"

10

724-05658

PIPE,PLUG 3/4NPS-POLY,GASKET

795-93851 13 of 48 12/23/21

#

PART NUMBER

DESCRIPTION

11

744-91276

FOAM RUBBER

STRIP,ADH.BK,NEOPRENE

12

314-06963 PL364, 115V

311-06123 PL364, 230V

312-44876 PL424, 115V

312-44878 PL424, 230V

MOTOR

13

730-07036

ELBOW,BARBED 3/8NPT X

5/8TUBE

14

756-07305

TRUARC RETAINER RING

5/8 I.D.

15

543-16763-74

DISC GM2GG

16

502M22478-74 PL364

502M22480-74 PL424

PUMP BODY

17

526-15486

VOLUTE COVER PLATE

18

647-26965 PL364

647-20551 PL424

SCREEN CYLINDER

19

432-44717

MOTOR COVER PL36 / PS6 /

PL422

20

646-44733-A

PUMP/MTR.MTG. PLATE

21

724-00991-13

Reducer Cplg. 3/8 x 1/4 galv

22

733-05546

HOSE CLAMP 7/8 NOM

23

729-06468

TUBE; 5/8" ID.

24

753-02877-81

SETSCREW, SOC HD 10-24

X 1/4

25

525-26542-76

IMPELLER 1-1/2 DIA

POLYPROP

26

744-91616

SANTOPRENE GASKET

27

543-16765-74

INTAKE SCREEN

795-93851 14 of 48 12/23/21

ACCESSORIES

Graymills manufacturers a wide variety of parts cleaning supplies and accessories for use with your

Handi-Kleen parts cleaner. Contact your Graymills Jobber or Distributor for more information on the

items listed below. (See Catalog GM100 for additional items)

Cleaning Brushes

Graymills parts cleaning brushes are specifically designed for tough parts cleaning work. The crimped

nylon fibers outwear ordinary brushes and won't ball up, flare out, or get flabby.

3B-G Standard Brush – with 2-1/2” polypropylene bristles.

5D Double Brush – 12 long, with heavy 2-1/2” bristles at one end and a fine 1-1/2” brush at the other

for crevices, holes, etc.

6A Flow-Thru Brush – flushes parts as they are cleaned. Solvent flows through the core of the handle.

Manufactured with a 2’ connecting hose, 2·1/2” nylon bristles, and a rubber connector which slips

over the nozzle of the flexible metal hose.

7A Flat Angular Flow-Thru cleaning brush with polyester bristles; can attach to pump nozzle with

included hose. Plastic Handle.

8A Round Angular handle cleaning brush with polyester bristles; can attach to pump nozzle with

included hose. Plastic handle.

Baskets

L-3 Permits flushing of small parts while keeping them organized. It measures 10” in diameter.

L-7 Ideal for small parts, the versatile basket is 8” L x 6” W x 4” H and hooks over the edge of any

Handi-Kleen unit or stands on legs.

L-8 Constructed of expanded metal on sides and bottom to accommodate big parts for thorough

soaking, the basket measures 13” L x 12” W x 5” H.

Drain Shelf

L-61 The Handi-Kleen parts cleaner also has a convenient 15-3/4” x 14-1/2” drain shelf which quickly

hooks on the left side of the cleaning tank. Fluid draining off clean parts runs directly back into

the tank.

Solvent Savers

Oil and Grease Removal (Packed two/carton)

SS-11 7" diameter x 11" long–includes one connecting hose

SS-18 7" diameter x 18" long–includes one connecting hose

Oil and Grease Plus Particulate Removal (Packed two/carton) In addition to special absorbent materials,

it contains a 5-micron filter cartridge that filters particulate from the solvent prior to oil and grease

absorbing stage.

SSC-11 7" diameter x 11" long–includes one connecting hose

SSC-18 7" diameter x 18" long-includes one connecting hose

Solvent Saver Hanging Bracket-Stainless Steel bracket holds filter out of way on inside of parts washer.

SS-BRAC 12" long x 9" deep X 8" high

795-93851 15 of 48 12/23/21

WARRANTY INFORMATION

Graymills Corporation warrants that the equipment manufactured and delivered, when properly

installed and maintained, shall be free from defects in workmanship and will function as quoted in the

published specification. Graymills does not warrant process performance, nor assume any liability for

equipment selection, adaptation, or installation.

Warranty does not apply to damages or defects caused by shipping, operator carelessness, misuse,

improper application or installation, abnormal use, use of add-on-parts or equipment which damages or

impairs the proper function of the unit, and modifications made to the unit. Warranty does not apply to

expendable parts needing replacement periodically due to normal wear and tear.

A new Warranty period shall not be established for repaired or replaced materials or products. Such items

shall remain under Warranty for only the remainder of the Warranty period of the original material or

product.

THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, WHETHER ORAL,

WRITTEN, EXPRESSED, IMPLIED OR STATUTORY. GRAYMILLS CORPORATION MAKES NO

OTHER WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. ALL IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE

AFORESTATED OBLIGATION ARE HEREBY DISCLAIMED BY GRAYMILLS CORPORATION AND

EXCLUDED FROM THIS SALE. Graymills warranty obligations and Buyer remedies (except to title), are

solely and exclusively stated herein. In no case will Graymills be liable for consequential damages, loss

of production, or any other loss incurred due to interruption of service.

Graymills' obligation under this Warranty shall be limited to:

1. Repairing or replacing (at Graymills sole discretion) any non-conforming or defective component

within one year from the date of shipment from Graymills.

2. Repairing or replacing (at Graymills sole discretion), components supplied by, but not

manufactured by Graymills, to the extent of the warranty given by the original manufacturer.

3. This warranty does not cover rusting of a mild-steel parts cleaner used with aqueous (water-

based) materials. Buyer must give Graymills prompt notice of any defect or failure.

Buyer must give Graymills prompt notice of any defect or failure.

If you believe you have a Warranty claim, contact Graymills at (773) 477-4100. Any return material must

have an RMA number on the outside of the package and shipping prepaid or shipment will be refused.

Graymills will promptly examine the material and determine if it is defective and within the Warranty

period.

795-93851 16 of 48 12/23/21

This page intentionally left blank.

795-93851 17 of 48 12/23/21

HANDI-KLEEN® LIMPIADORA DE PIEZAS –

SOLVENTE

Modelos PL364, PL424

Instrucciones de operación y mantenimiento

Graymills Corporation

2601 S. 25th Ave., Broadview, IL 60155

www.graymills.com

795-93851 18 of 48 12/23/21

INFORMACIÓN DE ENVÍO

Desempacado e inspección

Debe inspeccionar su equipo por posibles daños durante el envío.

Revise minuciosamente el equipo para detectar cualquier daño que pueda haber ocurrido durante el

transporte, por ejemplo, componentes y cables sueltos o rotos, herrajes o tornillos de montaje sueltos,

etc.

En caso de daños durante el envío

De conformidad con los términos y condiciones de contrato del transportista, la responsabilidad del

expedidor termina al momento de hacer el envío.

En caso de que encuentre daños, notifique al agente local de la empresa transportista.

Guarde la mercancía dañada y el material de empaque para que el agente de revisión lo inspeccione.

No devuelva ninguna mercancía antes de la inspección y autorización por parte de la empresa

transportista.

Presente un reclamo ante la empresa transportista. Fundamente el reclamo haciendo referencia al

reporte del agente. Tiene disponible una copia certificada de su factura cuando usted la solicite. La hoja

de envío original está adjunta a nuestra factura original. Si el envío fue prepagado, contáctenos para

obtener el recibo de transporte.

Avise a servicio al cliente en caso de que desee recibir asistencia y obtener un número de autorización

de devolución de material (RMA, por sus siglas en inglés).

Si el envío no está completo

Revise el manifiesto de carga, ya que los artículos que se envían sobre pedido están indicados en el

manifiesto de carga. Usted debe tener lo siguiente:

• Hoja de envío

• Manifiesto de carga

• Manual del usuario

Vuelva a inspeccionar el contenedor y material de empaque para verificar que no haya pasado por alto

ningún artículo pequeño durante el desempaque.

Si el envío no es correcto

Si el envío que recibió no está de acuerdo con lo que usted pidió, comuníquese con el departamento de

piezas y servicio inmediatamente. Tenga el número de pedido y el número de artículo a la mano. Guarde

los artículos hasta que reciba instrucciones para su envío.

Devoluciones

No devuelva ningún artículo dañado o incorrecto hasta que reciba instrucciones para el envío de

devolución por parte del departamento de servicio al cliente.

795-93851 19 of 48 12/23/21

INTRODUCCIÓN

La limpiadora de piezas Handi-Kleen es una limpiadora eficaz y económica. Las piezas se friegan con

un cepillo de mano (ver sección de ACCESORIOS) bajo una manguera flexible, mientras se posan sobre

un estante de metal móvible por encima del nivel del líquido o se pueden dejar en remojo en solvente

debajo del estante. El líquido de limpieza circula a través del colador de lodos con filtros de espuma para

atrapar las partículas más finas.

PL364 PL424

Características estándar

• Manguera de enjuague metálica flexible de puesta fija para enjuague dirigido a manos libres

• Depósito de acero con calibre 16 como mínimo y probado durante 24 horas después de soldarse

como resistente a las fugas, con acabado de revestimiento en polvo para larga vida y durabilidad

• Eslabón fusible de seguridad para cerrar la tapa en caso de incendio

• Drenado inferior conveniente para los cambios de líquido

• Canasta para piezas pequeñas

• Estante de trabajo extraíble para limpiar piezas por arriba del líquido o para ponerlas en remojo

en el depósito de solvente

• Cedazo y colador recolector de lodos

• Cumplimiento con norma de bordo libre (únicamente cuando el estante extraíble está instalado)

• Bomba 400 GPH Graymills Superflo™

795-93851 20 of 48 12/23/21

ADVERTENCIAS / PRECAUCIONES DE SEGURIDAD

ANTES de instalar o usar este equipo, lea todas las INSTRUCCIONES DE SEGURIDAD que vienen

en la máquina y en el manual. Mantenga este manual a la mano para referencia o capacitación.

Encontrará diferentes tipos de información sobre seguridad en las páginas siguientes y en las etiquetas

adheridas a los equipos Graymills. Las siguientes Declaraciones de seguridad explican su significado.

Este es el símbolo de alerta de seguridad. Se utiliza para ponerlo en alerta sobre posibles

riesgos de lesiones personales. Obedezca todas las indicaciones de seguridad que siguen a

este símbolo para evitar lesiones personales o la muerte.

PELIGRO significa que existe una situación de riesgo que, si no la evita, causará

lesiones graves o la muerte.

ADVERTENCIA significa que existe una situación de riesgo que, si no la evita,

podría causar lesiones graves o la muerte.

PRECAUCIÓN, utilizada junto con el símbolo de alerta de seguridad, significa que

existe una situación de riesgo que, si no la evita, podría causar lesiones menores a

moderadas.

PRECAUCIÓN, sin el símbolo de alerta de seguridad, se utiliza para indicar

prácticas que no están relacionadas con lesiones personales.

Antes de operar esta unidad lea y entienda el manual del usuario.

No opere la unidad cuando la temperatura ambiente máxima sea mayor que 100 °F (38 °C) ni

cerca de llamas, chispas o materiales humeantes. Mantenga la tapa cerrada cuando no esté en

uso.

Para mantener la protección continua contra riesgos de descarga eléctrica, incendio y explosión,

conecte la unidad a tomacorrientes o fuentes de alimentación conectadas a tierra correctamente.

Riesgo de explosión. Este equipo contiene piezas que generan arco eléctrico y chispas internas,

los cuales no deben exponerse a vapores inflamables. Este equipo no debe ubicarse en piso

desnivelado o por debajo del nivel del suelo.

Use únicamente líquidos limpiadores con punto de ignición mayor a 104 °F (40 °C). Consulte el

manual del usuario para ver la lista de solventes que ya fueron evaluados para su uso.

NO contamine la solución limpiadora con líquidos cuyo punto de ignición sea menor a 104 °F (40

°C), incluidos gasolina, alcohol u otros líquidos inflamables. Incluso pequeñas cantidades

generarán condiciones peligrosas.

Asegúrese de que el eslabón fusible y el dispositivo de cierre funcionen correctamente. El eslabón

fusible se funde a 165 °F (74 °C), lo cual causa que la tapa se cierre. Cuando está abierta, la tapa

debe inclinarse hacia adelante de modo que se cierre automáticamente cuando se funde el fusible.

NO manipule ni desmonte el eslabón fusible de seguridad. Si el eslabón fusible se rompe o se

pierde, NO use la unidad. Reemplace el eslabón fusible inmediatamente.

El nivel de voltaje presente es peligroso. Desconecte la alimentación eléctrica antes de realizar

cualquier reparación o limpieza del equipo. La unidad debe estar conectada a tierra correctamente

para prevenir riesgos de descarga eléctrica, incendio y explosión. Conecte la unidad únicamente

a tomacorrientes de tres clavijas. En caso de que el cable se agriete, deshilache o dañe de alguna

manera, debe ser reparado inmediatamente por un técnico electricista calificado. Nunca utilice

cables de extensión. Debido a que la seguridad del operador es una prioridad en todo momento,

recomendamos con firmeza que, más allá de que sea requerido o no por los reglamentos locales,

este equipo se conecte únicamente a una fuente de alimentación equipada con un "Interruptor de

La page est en cours de chargement...

Graymills Solvent Handi-Kleen PL364 PL424 -1204 Le manuel du propriétaire

Graymills Solvent Handi-Kleen PL364 PL424 -1204 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents