AstroStart RS-415 Le manuel du propriétaire

i

Congratulations

Congratulations on the purchase of your remote start system. Reading

this Owner’s Guide prior to using your system will help maximize the

use of your system and its many features. For more information please

visit us online (see back cover for URL). For any additional questions

please contact your authorized Directed dealer or contact Directed at

1-800-753-0600. (U.S. only) or 1-800-361-7271 (Canada only)

Additional support is also available at: http://support.directed.com

Important Information

Government Regulations and Safety Information

Read the Government Regulations and Warning! Safety

First sections of this manual prior to operating this system.

Warning! Failure to heed this information can result in

death, personal injury or property damage and may also

result in the illegal use of the system beyond its intended

purpose.

This product is designed for fuel-injected, automatic trans-

mission vehicles only. Installing it in a standard transmis-

sion vehicle is dangerous and is contrary to its intended

use. If your vehicle is equipped with a manual transmis-

sion cease use of this product and immediately return the

vehicle to an authorized Directed dealer.

G4115.2 2017-06

ii

Your Warranty

Your system comes with a warranty. The warranty terms are detailed at

the end of this guide. Make sure that you receive the proof of purchase

from your dealer, indicating the product was installed by an authorized

Directed dealer. Please register online (see back cover for URL).

Replacement Remote Controls

Please see your authorized dealer or visit us at www.directedstore.com

to order additional remote controls. Remote control part numbers are

found on the back of the device.

Contents

Congratulations .................................................................................................i

Important Information .........................................................................................i

Government Regulations and Safety Information ............................................i

Your Warranty ..........................................................................................ii

Replacement Remote Controls .....................................................................ii

Using Your System ........................................................................................... 2

Commands At a Glance ............................................................................2

Control Center ..........................................................................................2

Start Engine .............................................................................................2

Unlock Doors ...........................................................................................3

Stop Engine .............................................................................................3

Car Finder ...............................................................................................3

Using Remote Start ............................................................................................3

Key Takeover............................................................................................5

Safety Features .........................................................................................5

Pit Stop ....................................................................................................5

Optional Rear Defogger ............................................................................6

Optional Starter Anti-Grind Circuitry ...........................................................7

Disabling the Remote Start System/Garage Mode ........................................7

Remote Start Diagnostics ...........................................................................7

Pairing a Remote Control ...................................................................................9

Programming Options ......................................................................................10

Rapid Resume Logic .......................................................................................10

Battery Information ..........................................................................................11

Replacing the Battery ..............................................................................11

Battery Disposal .....................................................................................11

Patent Information ...........................................................................................12

Government Regulations ..................................................................................13

Warning! Safety first .......................................................................................14

Installation .............................................................................................14

Remote Start Capable .............................................................................14

Interference ............................................................................................15

Upgrades ..............................................................................................15

Water/Heat Resistance ...........................................................................15

Limited lifetime consumer warranty ....................................................................16

2

Using Your System

Commands At a Glance

System State Press/Release Press/Hold for 3 sec.

ENGINE OFF START ENGINE CAR FINDER

ENGINE ON UNLOCK DOORS STOP ENGINE

Control Center

Valet switch

LED

Button

LED

Control Center

Valet switch

LED

Button

LED

Control Center

Antenna

LED

Button

Antenna

Status LED

Control button

The Control Center, typically located on the upper part of the front

windshield receives commands from your system. It consists of:

• The antenna.

• The control center LED: a visual indicator of the system’s status.

• The control center button: for placing the system into Valet Mode

and to perform the Emergency Override operation.

Start Engine

When the engine is OFF, press and release the remote control button

to start the engine.

See"Using Remote Start" on page 3 for more feature details.

3

Unlock Doors

When the engine is ON, press and release the remote control but-

ton. The doors unlock, the parking lights ﬂash, the horn sounds (if con-

nected) as conﬁrmation.

Note: Horn honk may be an optional feature that requires additional

parts and labor.

Stop Engine

When the engine is ON, press and hold the remote control button for

three seconds. The engine stops running and the parking lights turn off.

Car Finder

When the engine is OFF, press and hold the remote control button for

three seconds. The parking lights ﬂash slowly several times allowing

you to locate your vehicle.

Using Remote Start

This feature allows you to remotely start and run your vehicle for a

programmable period of time. This makes it possible to warm up the

engine, and adjust the interior temperature of the vehicle with the cli-

mate control system. If interior heating or cooling is desired, the climate

controls must be preset, and the fan blower must be set to the desired

level prior to remote starting the vehicle.

Important! (1) Never remotely start the vehicle with the vehicle

in gear, and (2) Never remotely start the vehicle with the key

in the ignition.

4

Starting the Engine:

1. Make sure the parking brake is set. Press and release the remote

control button once* (or the amount of times the system has been

programmed to activate the remote start).

2. The parking lights ﬂash to conﬁrm that the vehicle is attempting to

start. In gasoline vehicles the engine will start approximately four

seconds after the parking lights ﬂash, in diesel vehicles the engine

starts after the WTS (WAIT-TO-START) timer has expired.

3. Once the vehicle has started, it will run for the pre- pro gram med

period of time (12, 24, or 60 minutes) or until a shutdown input

is trig gered.

* The factory setting is one press but this can also be programmed for

two or three presses maximum (see your authorized Directed installer

for the amount of presses programmed).

Record the number of presses to activate remote start here:

If the engine fails to start, refer to "Disabling the Remote Start System"

and "Remote Start Diagnostics" sections of this guide.

Satmode,

bank

selector

AUDIO

PWR

12

REWFF

PLAY/PROG NR

3456

DISC- DISC+

11:53

XM1-1 CH-001

CH

VOL

SCAN

SOUND

AM/FM

CD/AUX

SAT

RADIO

SEEK

SKIP

RPT

DISP -

MODE

A.SEL

RDM

TUNE

AUTO

OFF

DUAL

A/C

MODE

Channel control

category

modes

Bank and

present

indicator

Upper display

text mode

selector

Sat mode

and bank

selector

Preset 1-6.

Press until

beepto save

to a preset.

Channeland text

Indicator

fields

Toggles

Scan

mode

Tune mode

indicator

ANTENNA

SC OUTPUT

Sirius-Ready, SAT Radio Ready or select OEM headunits with optional Honda Bus Compatible Translator

Headunit bus cableSiriusConnect Cable

HON-SC1

Honda Bus

Compatible

Translator

Warning! It is unsafe to operate a vehicle's motor in a

garage or other closed off area. Such operation can

create a buildup of harmful gas. Breathing the exhaust

from the vehicle is hazardous and may lead to injury

or death.

5

Key Takeover

When you are ready to drive the vehicle:

1. Unlock the doors.

2. Enter the vehicle. Do not step on the foot brake.

3. Insert the key, turn it to the RUN (not START) position. Step on the

foot brake. The remote start is disabled and the parking lights turn

off.

4. Disengage the parking brake and begin driving.

Note

If your vehicle uses a Smart Key or PTS (Push-To-Start) system,

please refer to the vehicle speciﬁc instructions included with

the owner's guide of the interface module or consult your

authorized dealer.

Safety Features

The following safety features will disable the remote start when acti-

vated or not allow the engine to start if not properly set before starting.

• Foot Brake is depressed.

• Hood is open.

• Garage Mode is ON (see Disabling the Remote Start System).

• The pre-programmed run time (12, 24 or 60 minutes) has elapsed.

• Pressing and holding the button on the remote for three seconds

while the remote start is active.

• Parking brake is disengaged .

• Engine over-rev protection (Tachometer mode only).

Pit Stop

This remote start can keep the engine running during short trips away

from the vehicle.

6

Enabling Pit Stop Mode:

1. Park in a well ventilated area and set the parking brake.

2. With the engine running, set the transmission in the park position.

3. Press and release the remote control button once (or the amount

of times the system has been programmed to activate the remote

start). The parking lights turn on to conﬁrm.

4. Turn off the ignition and remove the key, the engine continues

running.

5. Exit and secure the vehicle, the engine runs for the programmed

runtime.

Important: This feature will not work if the brake pedal is being pressed.

Note

If your vehicle uses a Smart Key or PTS (Push-To-Start) system,

please refer to the vehicle speciﬁc instructions included with

the owner's guide of the interface module or consult your

authorized dealer.

Optional Rear Defogger

If connected, the Defogger circuit automatically activates after remote

starting the vehicle.

Note: The optional rear defogger feature can be programmed to be

on during remote start by your installer, however, you do not have the

capability to turn on and off the feature at will with the 1-button remote.

The rear defogger will always be active during the remote start runtime.

7

Optional Starter Anti-Grind Circuitry

This system includes an anti-grind circuit that can prevent damage to

the starter motor if the key is turned to the start position while the remote

start is ON.

Note: Anti-grind circuitry only works if an optional relay has been add-

ed and the remote start system is op er at ing the motor.

Disabling the Remote Start System/Garage Mode

Garage Mode is a safety feature that disables the remote start system if

the vehicle is parked in a garage, being serviced, or used by someone

unfamiliar with remote start systems.

When Garage Mode is ON, any attempt to start the engine, activate

Timer Mode, or enter Pit Stop mode is denied, and remote start diag-

nostics ﬂashes the parking lights nine times.

Turn Garage Mode ON or OFF:

1. Turn the ignition on then off.

2. Within 10 seconds, press and release the Control Center button

once. The Control Center LED turns on.

3. The parking lights ﬂash:

• Nine times quickly when turning on.

• Nine times slowly when turning off.

Remote Start Diagnostics

For user safety, the system must be properly conﬁgured or remote start

will not activate. A Remote Start Fault may be caused by any of several

conﬁguration issues. If the remote start fails to activate, refer to the table

8

below for the command type and parking light ﬂashes that will identify

the conﬁguration issue and solution.

Light Flash Problem Solution

5 ﬂashes Brake is on Release the foot brake

6 ﬂashes Hood is open Close the hood

8 ﬂashes Neutral safety is disconnected Set the parking brake or move

the shifter to the park position

9 ﬂashes Garage Mode is ON Turn Garage Mode OFF

9

Pairing a Remote Control

Your system comes with the remote controls already programmed, how-

ever, if you are replacing or adding additional remote controls, they

must be paired to the system prior to operating the system. To pair the

remote, you need to know where the Control button is located. If the

horn honk is not connected, the Control Center LED needs to be visible

for visual conﬁrmation. If you cannot locate or access the main unit, it is

recommended that you visit your authorized dealer to pair the remote.

The system is capable of accepting up to four remote controls.

1. Turn key to the ON position

2. Within 10 seconds, press and release Control button once.

3. Within 10 seconds, press and hold the Control button. The LED

ﬂashes one time and the horn honks (if connected) to conﬁrm entry

into remote pairing. Do not release the Control button.

4. Press the button on the remote control. The horn honks to conﬁrm

the remote has been paired.

5. Release the Control button.

6. Turn the key to the OFF position. The horn sounds one long honk

(if connected) to conﬁrm that remote pairing has exited.

The programming routine exits if any of the following occurs:

• The ignition is turned off.

• There is no activity for 30 seconds.

• The Control button is pressed too many times.

10

Programming Options

Feature options will control your system's normal operation. Some op-

tions may require additional parts and installation labor. The following

is a list of the programmable options with the factory settings in bold.

• 12 minute to 60 minute runtime. Your system can be programmed

to allow the vehicle to run for up to 60 minutes when remote

started. This can be set up to minute increments by your installer.

• Parking lights ﬂashing or constant. Your system can be programmed

to ﬂash the parking lights or have them come on constantly during

the remote start operation.

• Ignition controlled door locking ON or OFF. With this feature on,

the doors will lock three seconds after the ignition key is turned on,

and will unlock when the ignition key is turned off.

Important: The door lock option must be installed for the ignition

controlled door lock feature to work.

Rapid Resume Logic

This Directed system stores its current state to non-volatile memory. If the

power to the system is disconnected and then reconnected, the system

recalls the stored state from memory.

11

Battery Information

The remote control is powered by two 3V, CR2016 batteries. When

the battery begins to weaken, operating range is reduced and the LED

on the remote control dims.

Replacing the Battery

1. Use a small ﬂat blade screw driver and insert it into the slot lo-

cated along the bottom of the remote, near the key ring. Carefully

pry open the case.

2. Remove the old batteries from the holding clip. Orient the new

batteries for the correct polarity and insert into the holding clip.

3. Reposition the case parts, then snap together by pressing ﬁrmly

and evenly on the front and back.

Battery Disposal

Directed cares about the environment. If you need to dispose

of the battery, please do so in accordance with your munici-

pal requirements for battery disposal or return to Directed.

12

Patent Information

This product is covered by one or more of the following United States

patents:

Remote Start Patents:

5,349,931; 5,872,519; 5,914,667; 5,952,933; 5,945,936;

5,990,786; 6,028,372; 6,467,448; 6,561,151; 7,191,053;

7,483,783

Vehicle Security Patents:

5,467,070; 5,532,670; 5,534,845; 5,563,576; 5,646,591;

5,650,774; 5,673,017; 5,712,638; 5,872,519; 5,914,667;

5,952,933; 5,945,936; 5,990,786; 6,028,505; 6,452,484

Other patents pending.

13

Government Regulations

This device complies with Part 15 of FCC rules. Operation is subject to the fol-

lowing two conditions: (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency ener-

gy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television, which can

be determined by turning the equipment OFF and ON, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

This device complies with the Industry Canada Radio Standards Speciﬁcation

RSS 210. Its use is authorized only on a no-interference, no-protection basis; in

other words, this device must not be used if it is determined that it causes harm-

ful interference to services authorized by IC. In addition, the user of this device

must accept any radio interference that may be received, even if this interference

could affect the operation of the device.

Warning: Changes or modiﬁcations not expressly approved by the party re-

sponsible for compliance could void the user’s authority to operate this device.

14

Warning! Safety ﬁrst

Please read the safety warnings below before proceeding. Improper use of the

product may be dangerous or illegal.

Installation

Due to the complexity of this system, installation of this product must only be performed

by an authorized Directed dealer. If you have any questions, ask your retailer or contact

Directed directly at 1-800-753-0600.

Remote Start Capable

When properly installed, this system can start the vehicle via a command signal from the

remote control transmitter. Therefore, never operate the system in an enclosed area or par-

tially enclosed area without ventilation (such as a garage). When parking in an enclosed

or partially enclosed area or when having the vehicle serviced, the remote start system must

be disabled using the "Disabling the Remote Start System/Garage Mode" procedure in this

guide. It is the user’s sole responsibility to properly handle and keep out of reach from chil-

dren all remote control transmitters to assure that the system does not unintentionally remote

start the vehicle. IT IS RECOMMENDED THAT THE USER INSTALL A CARBON MONOX-

IDE DETECTOR IN THE LIVING AREAS ADJACENT TO THE VEHICLE. ALL DOORS LEAD-

ING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED

VEHICLE STORAGE AREA MUST BE CLOSED AT ALL TIMES. These precautions are the sole

responsibility of the user.

Use of this product in a manner contrary to its intended mode of operation may result in

property damage, personal injury, or death. (1) Never remotely start the vehicle with the ve-

hicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user

must also have the neutral safety feature of the vehicle periodically checked, wherein the

vehicle must not remotely start while the car is in gear. This testing should be performed by

an authorized Directed dealer in accordance with the Safety Check outlined in the product

installation guide. If the vehicle starts in gear, cease remote start operation immediately and

consult with the authorized Directed dealer to ﬁx the problem.

After the remote start module has been installed, contact your authorized dealer to have him

or her test the remote start module by performing the Safety Check outlined in the product

installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit

test, the remote start unit has not been properly installed. The remote start module must be

15

removed or the installer must properly reinstall the remote start system so that the vehicle

does not start in gear. All installations must be performed by an authorized Directed dealer.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS

CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE

START SYSTEM UNDER THESE CONDITIONS MAY CAUSE THE VEHICLE TO UNEXPECT-

EDLY LUNGE FORWARD RESULTING IN PROPERTY DAMAGE OR SERIOUS PERSONAL

INJURY INCLUDING DEATH. YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT

AND SEEK THE ASSISTANCE OF AN AUTHORIZED DIRECTED DEALER TO REPAIR OR

DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD

RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

This product is designed for fuel-injected, automatic transmission vehicles only. Installing it in

a standard transmission vehicle is dangerous and is contrary to its intended use.

Interference

All radio devices are subject to interference which could affect proper performance.

Upgrades

Any upgrades to this product must be performed by an authorized Directed dealer. Do not

attempt to perform any unauthorized modiﬁcations to this product.

Water/Heat Resistance

This product is not designed to be water and/or heat-resistant. Please take care to keep

this product dry and away from heat sources. Any damage from water or heat will void

the warranty.

16

Limited lifetime consumer warranty

Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace (at

Directed’s election) with a comparable reconditioned model any Directed unit (hereafter the

“unit”), excluding without limitation the siren, the remote transmitters, the associated sensors

and accessories, which proves to be defective in workmanship or material under reason-

able use during the lifetime of the vehicle provided the following conditions are met: the

unit was purchased from an authorized Directed dealer, the unit was professionally installed

and serviced by an authorized Directed dealer; the unit will be profession¬ally reinstalled

in the vehicle in which it was originally installed by an authorized Directed dealer; and the

unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other

dated proof of purchase bearing the following information: consumer’s name, telephone

number and address; the authorized dealers name, telephone number and address; com-

plete product description, including accessories; the year, make and model of the vehicle;

vehicle license number and vehicle identification number. All components other than the

unit, including without limitation the siren, the remote transmitters and the associated sensors

and accessories, carry a one-year warranty from the date of purchase of the same. ALL

PRODUCTS RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF

PURCHASE FROM AN AUTHORIZED DEALER WILL BE DENIED. This warranty is non-

transferable and is automatically void if: the unit’s date code or serial number is defaced,

missing or altered; the unit has been modified or used in a manner contrary to its intended

purpose; the unit has been damaged by accident, unreasonable use, neglect, improper

service, installation or other causes not arising out of defects in materials or construction.

The warranty does not cover damage to the unit caused by installation or removal of the

unit. Directed, in its sole discretion, will determine what constitutes excessive damage and

may refuse the return of any unit with excessive damage.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING

BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF

MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-

INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND

DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME

FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.

DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS

OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED

SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE

THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST

VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS;

AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING

WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS

WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR

REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND.

IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY,

THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.

CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN

THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED

SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE

PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES

WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,

INCIDENTAL DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME,

LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY

AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER

A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT TO

THE CONDITIONS AS DESCRIBED HEREIN. THIS WARRANTY IS VOID IF THE UNIT

HAS NOT BEEN PURCHASED FROM DIRECTED, OR AN AUTHORIZED DIRECTED

DEALER, OR IF THE UNIT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE,

NEGLIGENCE, ACTS OF GOD, NEGLECT, IMPROPER SERVICE, OR OTHER CAUSES

NOT ARISING OUT OF DEFECT IN MATERIALS OR CONSTRUCTION.

Some states do not allow limitations on how long an implied warranty will last or the exclu-

sion or limitation of incidental or consequential damages. This warranty gives you specific

legal rights and you may also have other rights that vary from State to State.

This warranty is only valid for sale of product(s) within the United States of America and

in Canada. Product(s) sold outside of the United States of America or Canada are sold

“AS-IS” and shall have NO WARRANTY, express or implied.

For further details relating to warranty information of Directed products, please visit the

support section of Directed’s website at: www.directed.com

This product may be covered by a Guaranteed Protection Plan (“GPP”). See your

authorized Directed dealer for details of the plan or call Directed Customer Service at

1-800-876-0800.

920-10011-01 2011-06

La page charge ...

AstroStart RS-415 Le manuel du propriétaire

AstroStart RS-415 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents