AstroStart RS-405 Le manuel du propriétaire

i

Congratulations

Congratulations on the purchase of your state-of-the-art keyless entry

and remote start system. Reading this Owner’s Guide prior to using

your system will help maximize the use of your system and its many

features. For more information please visit us online (see back cover

for URL). For any additional questions please contact your authorized

Directed dealer or contact Directed at 1-800-753-0600. (U.S. only) or

1-800-361-7271 (Canada only). Additional support is also available

at: http://support.directed.com

Important Information

Government Regulations and Safety information

Read the Government Regulations and Warning! Safety

First sections of this manual prior to operating this system.

Warning! Failure to heed this information can result in

death, personal injury or property damage and may also

result in the illegal use of the system beyond its intended

purpose.

This product is designed for fuel-injected, automatic trans-

mission vehicles only. Installing it in a standard transmis-

sion vehicle is dangerous and is contrary to its intended

use. If your vehicle is equipped with a manual transmis-

sion cease use of this product and immediately return the

vehicle to an authorized Directed dealer.

G4105.2 2017-06

ii

Your Warranty

Your system comes with a warranty. The warranty terms are detailed at

the end of this guide. Make sure that you receive the proof of purchase

from your dealer, indicating the product was installed by an authorized

Directed dealer.

Replacement remote controls

Please see your authorized dealer or visit us at www.directedstore.com

to order additional remote controls. Remote control part numbers are

found on the back of the device.

Contents

Congratulations ................................................................................................i

Important Information .........................................................................................i

Government Regulations and Safety information ........................................... i

Your Warranty ..........................................................................................ii

Replacement remote controls ...................................................................... ii

Remote Control .................................................................................................3

Control Center ..........................................................................................3

Remote Control Functions ...................................................................................4

Standard Configuration .............................................................................4

Using the System .............................................................................................6

Locking ....................................................................................................6

Unlocking ................................................................................................6

Disabling (optional) Starter Disable ............................................................6

Panic Mode .............................................................................................7

Remote Start ............................................................................................. 7

Key Takeover............................................................................................8

Safety Features .........................................................................................9

Pit Stop ....................................................................................................9

Car Finder .............................................................................................10

Optional Starter Anti-Grind Circuitry .........................................................10

Disabling the Remote Start System/Garage Mode ......................................10

Remote Start Diagnostics .........................................................................11

Pairing a Remote Control .................................................................................12

Programming Options ......................................................................................13

Rapid Resume Logic .......................................................................................13

Battery Information ..........................................................................................14

Replacing the Battery ..............................................................................14

Battery Disposal .....................................................................................14

Patent Information ...........................................................................................15

Government Regulations ..................................................................................16

Warning! Safety first .......................................................................................17

Installation .............................................................................................17

Remote Start Capable .............................................................................17

Interference ............................................................................................18

Upgrades ..............................................................................................18

Water/Heat Resistance ...........................................................................18

Limited lifetime consumer warranty ....................................................................19

3

Remote Control

Feature Description

Internal Antenna Used for transmitting information

Transmit LED Active when transmitting information

Command buttons (4)

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

AUX

Used to perform:

Locking

Unlocking

Remote Start

Silent mode/Auxiliary channel

Trunk Release

Control Center

Valet switch

LED

Button

LED

Control Center

Valet switch

LED

Button

LED

Control Center

Antenna

LED

Button

Antenna

Status LED

Control button

The Control Center, typically located on the upper part of the front

windshield receives commands from your system. It consists of:

• The antenna.

• The Control Center LED: a visual indicator of the system’s status.

• The Control Center button: for placing the system into Garage

Mode and to perform the Emergency Override operation.

4

Remote Control Functions

The remote buttons are used to send commands to the system. The but-

tons indicated below are for standard conﬁguration.

Standard Conﬁguration

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

Button

The lock function is controlled by pressing

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

on the remote control

for one second. When held for approximately two seconds, Panic is

activated.

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.

Button

The unlocking function is controlled by pressing

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

on the remote con-

trol for one second. You can also turn Panic off with this button.

or Button

Silent Mode

™

and an optional auxiliary function are controlled by

pressing

or . Silent Mode works by pressing or

for less than one second before locking or unlocking. An optional auxil-

iary function such as trunk release may be controlled by pressing and

holding

or for approximately two seconds.

AUX

Button

The remote start function of your system is controlled by pressing this

button for one second.

AUX

and or Buttons

Car Finder is controlled by pressing these two buttons.

5

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

and

AUX

and or Buttons

When simultaneously pressed these buttons control the optional rear

window defogger during remote starting. The parking lights ﬂash three

times to conﬁrm activation. Once activated, the defogger will turn on

whenever the vehicle is remote started.

The parking lights ﬂash twice when the defogger is deactivated. The

defogger does not turn on when the vehicle is remote started.

Important note: Defogger is an optional feature. Additional parts and

labor may be required. See your Directed dealer for details.

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

and

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.

Buttons

Timer Mode is activated when these buttons are pressed simultaneously.

When you activate Timer Mode the parking lights ﬂash four times, after a

one second delay the engine starts. To turn the engine off, without exiting

Timer Mode, press the

AUX

.

The system remains in Timer Mode and will start every three hours for a

maximum of six starts unless cancelled by turning on the ignition, or by

activating any of the shutdown inputs to the system.

The parking lights ﬂash four times indicating Timer Mode is exited.

6

Using the System

Locking

Pressing

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.

for one second locks the system (if the door locks are con-

nected). The horn honks and the parking lights ﬂash once to conﬁrm

the system is locked. The Failsafe

®

Starter Disable also activates and

prevents the vehicle’s starter from cranking.

Important note: Horn honk and Failsafe are both optional features.

Unlocking

Pressing

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.

for one second unlocks the doors (if connected). The horn

honks twice and the parking lights ﬂash twice to conﬁrm unlocking of

the system. The Failsafe Starter Disable (if connected) is deactivated.

Disabling (optional) Starter Disable

If your remote control is lost or damaged, you can manually override

the Starter Disable. To do this, you must have the ve hi cle's ignition key

and know where the Control button is located. Be sure to check with

the installer for the location of the Control button.

To override the Starter Disable, turn the ignition on and press and

release the Control button within 10 seconds. The vehicle should now

start. If it does not start, you may have waited too long; turn the ignition

off and repeat the process.

Location of Control button: ____________________

7

Panic Mode

If you are threatened in or near your vehicle, you can attract atten-

tion by trig ger ing the system with your remote control. Press

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

for

approximately two seconds to enter Panic Mode. In Panic Mode, the

horn will honk and the parking lights will ﬂash for 30 seconds. To stop

Panic Mode at any time, press

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

, or

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

on the remote control.

Note: In order for Panic Mode to be effective, the vehicle’s horn (or

optional siren) and the vehicle's parking lights must be connected.

Remote Start

This feature allows you to remotely start and run your vehicle for a

pro gram ma ble period of time. This makes it possible to warm up the

engine, and adjust the interior tem per a ture of the ve hi cle with the cli-

mate control system. If interior heating or cooling is desired, the climate

controls must be preset, and the fan blower must be set to the desired

level prior to remote starting the vehicle.

Satmode,

bank

selector

AUDIO

PWR

12

REWFF

PLAY/PROG NR

3456

DISC- DISC+

11:53

XM1-1 CH-001

CH

VOL

SCAN

SOUND

AM/FM

CD/AUX

SAT

RADIO

SEEK

SKIP

RPT

DISP -

MODE

A.SEL

RDM

TUNE

AUTO

OFF

DUAL

A/C

MODE

Channel control

Category

Control

Text selector.

Hold for 10secto toggle

channelor category

tune

modes.

Toggles

Scan

mode

Bank and

present

indicator

Channel

and text

indicator

Preset 1-6.

Hold until beepto

savetoapreset.

CATEGORY

Tune mode

indicator

MODE

DUAL

OFF

AUTO

MAP/

GUIDE

MENU

SETUP

INFO

ZOOM

CANCEL

AUDIO

AUTO

MODE

A/C

LOAD

DISC

TAPE

AM/FM

DISP

MODE

SCAN RPT A.SEL/RDM-SEEK +

1

2

34

5

6

DISC-

DISC+

VOL

PWR

PUSH

TUNE

SOUND

PUSH

XM1-1

VOL

CH

CHANNEL

CATEGORY

NAME

TITLE

:

1

CH

2

CH

3

CH

6

CH

5

CH

4

CH

MODE SCAN SOUND

001-HITS1

POP

MUSICNAME

MUSIC TITLE

Channel control

Category

Control

001 014 018

040 065

115

Toggles between

channel and

Category

Control

Text selector.

Hold for 10secto toggle

channelor category

tune

modes.

Toggles

Scan

mode

Bank and

present

indicator

Channel

and text

indicator

Preset 1-6.

Hold until beepto

savetoapreset.

CATEGORY

Tune mode

indicator

MODE

DUAL

OFF

AUTO

MAP/

GUIDE

MENU

SETUP

INFO

ZOOM

CANCEL

AUDIO

AUTO

MODE

A/C

LOAD

DISC

TAPE

AM/FM

DISP

MODE

SCAN RPT A.SEL/RDM-SEEK +

1

2

34

5

6

DISC-

DISC+

VOL

PWR

PUSH

TUNE

SOUND

PUSH

XM1-1

VOL

CH

CHANNEL

CATEGORY

NAME

TITLE

:

1

CH

2

CH

3

CH

6

CH

5

CH

4

CH

MODE SCAN SOUND

001-HITS1

POP

MUSICNAME

MUSIC TITLE

Channel control

Category

Control

001 014 018

040 065

115

Toggles between

channel and

category

modes

Bank and

present

indicator

Upper display

text mode

selector

Sat mode

and bank

selector

Preset 1-6.

Press until

beepto save

to a preset.

Channeland text

Indicator

fields

Toggles

Scan

mode

Tune mode

indicator

ANTENNA

SC OUTPUT

Sirius-Ready, SAT Radio Ready or select OEM headunits with optional Honda Bus Compatible Translator

Headunit bus cableSiriusConnect Cable

HON-SC1

Honda Bus

Compatible

Translator

Warning! It is unsafe to operate a vehicle's motor in a

garage or other closed off area. Such operation can

create a buildup of harmful gas. Breathing the exhaust

from the vehicle is hazardous and may lead to injury

or death.

Key Takeover

When you are ready to drive the vehicle:

1. Unlock the doors.

2. Enter the vehicle. Do not step on the foot brake.

3. Insert the key, turn it to the RUN (not START) position. Step on the

foot brake. The remote start is disabled and the parking lights turn

off.

4. Disengage the parking brake and begin driving.

Note

If your vehicle uses a Smart Key or PTS (Push-To-Start) system,

please refer to the vehicle speciﬁc instructions included with

the owner's guide of the interface module or consult your

authorized dealer.

9

Safety Features

The following safety features will disable the remote start when acti-

vated or not allow the engine to start if not properly set before starting.

• Foot Brake is depressed.

• Hood is opened.

• Garage Mode is ON (see Disabling the Remote Start System).

• The pre-programmed run time (12, 24 or 60 minutes) has elapsed.

• Remote Start activation procedure is repeated.

• Parking brake is disengaged.

• Engine over-rev protection (Tachometer mode only).

•

Pit Stop

This remote start can keep the engine running during short trips away

from the vehicle.

To enable Pit Stop Mode:

1. Park in a well ventilated area.

2. With the engine running, set the transmission in the park position

and ensure the parking brake is set.

3. Press and release the

AUX

button once (or the amount of times the

system has been programmed to activate the remote start), the

parking lights turn on to conﬁrm.

4. Turn off the ignition and remove the key, the engine continues

running.

5. Exit and secure the vehicle, the engine runs for the programmed

runtime.

Important: This feature will not work if the brake pedal is being pressed.

10

Note

If your vehicle uses a Smart Key or PTS (Push-To-Start) system,

please refer to the vehicle speciﬁc instructions included with

the owner's guide of the interface module or consult your

authorized dealer.

Car Finder

Car ﬁnder allows you to locate your vehicle, by having the system ﬂash

the parking lights.

To activate:

1. Press and release the

AUX

and or buttons at the same

time.

2. The parking lights ﬂash slowly several times, allowing you to lo-

cate your vehicle.

Optional Starter Anti-Grind Circuitry

This system includes an anti-grind circuit that can prevent damage to

the starter motor if the key is turned to the start position while the remote

start is ON.

Note: Anti-grind circuitry only works if an optional relay has been add-

ed and the vehicle is remote started.

Disabling the Remote Start System/Garage Mode

Garage Mode is a safety feature that disables the remote start system if

the vehicle is parked in a garage, being serviced, or used by someone

unfamiliar with remote start systems.

When Garage Mode is ON, any attempt to start the engine, activate

Timer Mode, or enter Pit Stop mode is denied and remote start diag-

nostics ﬂashes the parking lights nine times.

11

Turn Garage Mode ON or OFF:

1. Turn the ignition on then off.

2. Within 10 seconds, press and release the Control Center button

once. The Control Center LED turns on.

3. The parking lights ﬂash:

• Nine times quickly when turning on.

• Nine times slowly when turning off.

Remote Start Diagnostics

For user safety, the system must be properly conﬁgured or remote start

will not activate. A Remote Start Fault may be caused by any of several

conﬁguration issues. If the remote start fails to activate, refer to the table

below for the command type and parking light ﬂashes that will identify

the conﬁguration issue and solution.

Light Flash Problem Solution

5 ﬂashes Brake is on Release the foot brake

6 ﬂashes Hood is open Close the hood

8 ﬂashes Neutral safety is disconnected Set the parking brake or move

the shifter to the park position

9 ﬂashes Garage Mode is ON Turn Garage Mode OFF

12

Pairing a Remote Control

Your system comes with the remote controls already programmed, how-

ever, if you are replacing or adding additional remote controls, they

must be paired to the system prior to operating the system. To pair the

remote, you need to know where the Control button is located. If the

horn honk is not connected, the Control Center LED needs to be visible

for visual conﬁrmation. If you cannot locate or access the main unit, it is

recommended that you visit your authorized dealer to pair the remote.

The system is capable of accepting up to four remote controls.

1. Turn key to the ON position

2. Within 10 seconds, press and release the Control button once.

3. Within 10 seconds, press and hold the Control button. The LED

on the Control Center ﬂashes one time and the horn (if connected)

honks to conﬁrm entry into remote pairing. Do not release the

Control button.

4. Press the

AUX

Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pr y case apart. Replace battery and then snap case together.

button on the remote control. The horn honks to con-

ﬁrm the remote has been paired.

5. Release the Control button.

6. Turn the key to OFF position. The horn sounds one long honk (if

connected) to conﬁrm that remote pairing has exited.

The programming routine exits if any of the following occurs:

• The ignition is turned off.

• There is no activity for 30 seconds.

• The Control button is pressed too many times.

13

Programming Options

Feature options will control your system's normal operation. Some op-

tions may require additional parts and installation labor. The following

is a list of the programmable options with the factory settings in bold.

• 12 minute to 60 minute runtime. Your system can be programmed

to allow the vehicle to run for up to 60 minutes when remote

started. This can be set up to minute increments by your installer.

• Parking lights ﬂashing or constant. Your system can be programmed

to ﬂash the parking lights or have them come on constantly during

the remote start operation.

• Ignition controlled door locking ON or OFF. With this feature on,

the doors will lock three seconds after the ignition key is turned on,

and will unlock when the ignition key is turned off.

Important: The door lock option must be installed for the ignition

controlled door lock feature to work.

Rapid Resume Logic

This Directed system stores its current state to non-volatile memory. If the

power to the system is disconnected and then reconnected, the system

recalls the stored state from memory.

14

Battery Information

The remote control is powered by two 3V, CR2016 batteries. When

the battery begins to weaken, operating range is reduced and the LED

on the remote control dims.

Replacing the Battery

1. Use a small ﬂat blade screw driver and insert it into the slot lo-

cated along the bottom of the remote, near the key ring. Carefully

pry open the case.

2. Remove the old batteries from the holding clip. Orient the new

batteries for the correct polarity and insert into the holding clip.

3. Reposition the case parts, then snap together by pressing ﬁrmly

and evenly on the front and back.

Battery Disposal

Directed cares about the environment. If you need to dispose

of the battery, please do so in accordance with your munici-

pal requirements for battery disposal.

15

Patent Information

This product is covered by one or more of the following United States

patents:

Remote Start Patents:

5,349,931; 5,872,519; 5,914,667; 5,952,933; 5,945,936;

5,990,786; 6,028,372; 6,467,448; 6,561,151; 7,191,053;

7,483,783

Vehicle Security Patents:

5,467,070; 5,532,670; 5,534,845; 5,563,576; 5,646,591;

5,650,774; 5,673,017; 5,712,638; 5,872,519; 5,914,667;

5,952,933; 5,945,936; 5,990,786; 6,028,505; 6,452,484

Other patents pending.

16

Government Regulations

This device complies with Part 15 of FCC rules. Operation is subject to the fol-

lowing two conditions: (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential instal-

lation. This equipment generates and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television, which can be determined by

turning the equipment OFF and ON, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with the Industry Canada Radio Standards Speciﬁcation

RSS 210. Its use is authorized only on a no-interference, no-protection basis; in

other words, this device must not be used if it is determined that it causes harm-

ful interference to services authorized by IC. In addition, the user of this device

must accept any radio interference that may be received, even if this interference

could affect the operation of the device.

Warning:

Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate this device.

17

Warning! Safety ﬁrst

Please read the safety warnings below before proceeding. Improper use of the

product may be dangerous or illegal.

Installation

Due to the complexity of this system, installation of this product must only be performed

by an authorized Directed dealer. If you have any questions, ask your retailer or contact

Directed directly at 1-800-753-0600.

Remote Start Capable

When properly installed, this system can start the vehicle via a command signal from

the remote control. Therefore, never operate the system in an enclosed area or partially

enclosed area without ventilation (such as a garage). When parking in an enclosed or

partially enclosed area or when having the vehicle serviced, the remote start system must

be disabled using the "Disabling the Remote Start System/Garage Mode" procedure in

this guide. It is the user’s sole responsibility to properly handle and keep out of reach from

children all remote control devices to assure that the system does not unintentionally remote

start the vehicle. IT IS RECOMMENDED THAT THE USER INSTALL A CARBON MONOX-

IDE DETECTOR IN THE LIVING AREAS ADJACENT TO THE VEHICLE. ALL DOORS LEAD-

ING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED

VEHICLE STORAGE AREA MUST BE CLOSED AT ALL TIMES. These precautions are the sole

responsibility of the user.

Use of this product in a manner contrary to its intended mode of operation may result in

property damage, personal injury, or death. (1) Never remotely start the vehicle with the ve-

hicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user

must also have the neutral safety feature of the vehicle periodically checked, wherein the

vehicle must not remotely start while the car is in gear. This testing should be performed by

an authorized Directed dealer in accordance with the Safety Check outlined in the product

installation guide. If the vehicle starts in gear, cease remote start operation immediately and

consult with the authorized Directed dealer to ﬁx the problem.

After the remote start module has been installed, contact your authorized dealer to have him

or her test the remote start module by performing the Safety Check outlined in the product

installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit

18

test, the remote start unit has not been properly installed. The remote start module must be

removed or the installer must properly reinstall the remote start system so that the vehicle

does not start in gear. All installations must be performed by an authorized Directed dealer.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS

CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE

START SYSTEM UNDER THESE CONDITIONS MAY CAUSE THE VEHICLE TO UNEXPECT-

EDLY LUNGE FORWARD RESULTING IN PROPERTY DAMAGE OR SERIOUS PERSONAL

INJURY INCLUDING DEATH. YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT

AND SEEK THE ASSISTANCE OF AN AUTHORIZED DIRECTED DEALER TO REPAIR OR

DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD

RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

This product is designed for fuel-injected, automatic transmission vehicles only. Installing it in

a standard transmission vehicle is dangerous and is contrary to its intended use..

Interference

All radio devices are subject to interference which could affect proper performance.

Upgrades

Any upgrades to this product must be performed by an authorized Directed dealer. Do not

attempt to perform any unauthorized modiﬁcations to this product.

Water/Heat Resistance

This product is not designed to be water and/or heat-resistant. Please take care to keep

this product dry and away from heat sources. Any damage from water or heat will void

the warranty.

La page charge ...

AstroStart RS-405 Le manuel du propriétaire

AstroStart RS-405 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents