Simplicity 7800954-01 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
7106180USCN
Revision D
en
Operator’s Manual
es
Manual del operador
fr
Manuel d’utilisation
Copyright © Briggs & Stratton Power Products Group, LLC
Milwaukee, WI USA. All Rights Reserved
Not For
Reproduction
2
Not For
Reproduction
3
en
Thank you for purchasing this quality-built Rear Engine
Rider. We’re pleased that you’ve placed your confidence
in the brand. When operated and maintained according
to the manuals, your product will provide many years of
dependable service.
The manuals contain safety information to make you aware
of the hazards and risks associated with the unit and how
to avoid them. This Rear Engine Rider was designed to be
used as described in operator’s manual and is not intended
for any other purpose. It is important that you read and
understand the instructions thoroughly before attempting
to start or operate this equipment. Save these original
instructions for future reference.
This product requires final assembly before use. Refer
to the setup guide for instructions on final assembly
procedures. Follow the instructions completely.
Manual Contents:
Operator Safety ............................................................... 3
Features and Controls
.................................................... 9
Safety Interlock Systems Checks ................................ 10
Operation ....................................................................... 10
Maintenance .................................................................. 19
Troubleshooting ............................................................ 24
Specifications ................................................................ 25
The images in this document are representative, and are
meant to complement the instructional text they accompany.
Your unit may vary from the images displayed. LEFT and
RIGHT are as seen from the operator’s position.
Operator Safety
Safety Alert Symbol and Signal Words
The safety alert symbol indicates a potential personal
injury hazard. A signal word (DANGER, WARNING, or
CAUTION) is used with the alert symbol to designate a
degree or level of hazard seriousness. A safety symbol may
be used to represent the type of hazard. The signal word
NOTICE is used to address practices not related to
personal injury.
DANGER indicates a hazard which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE indicates an action that could result in damage to
the product.
Hazard Symbols
General Operator Safety Warning
Symbol Meaning Symbol Meaning
Safety
information
about hazards
that can result in
personal injury.
Read and
understand
the operator’s
manual before
operating or ser-
vicing the unit.
Thrown objects
hazard.
Amputation
hazard - rotating
blade. Keep feet
away.
Amputation
hazard - do not
touch moving
parts.
Amputation
hazard - rotat-
ing blade. Keep
hands away.
Keep
bystanders and
children away.
Toxic fume haz-
ard.
Fire hazard. Explosion haz-
ard.
Battery
explosion
hazard.
Shock hazard.
Hot surface
hazard.
Explosion haz-
ard.
Shock hazard. Kickback haz-
ard.
Eye protection
recommended.
Ear protection
recommended
for extended
use.
Remove the
key before
performing
service.
Remove the
spark plug wire
before perform-
ing service.
Not For
Reproduction
4
3. DO NOT allow children or others to ride on machine,
attachments or towed equipment (even with the blades
OFF). They may fall and be seriously injured.
4. DO NOT allow pre-teenage children to operate machine.
5. ALLOW only responsible adults & teenagers with
mature judgment under close adult supervision to
operate machine.
6. DO NOT operate blades in reverse unless absolutely
necessary. STOP BLADES. LOOK and SEE behind and
down for children, pets and hazards before and while
backing.
7. USE EXTRA CARE when approaching blind corners,
shrubs, trees, or other objects that may obscure vision.
Protection Against Tip-Overs/Roll-Overs
Slopes are a major factor related to loss-of-control and
tipover/roll-over accidents, which can result in severe injury
or death. All slopes require extra CAUTION. If you cannot
back up the slope or if you feel uneasy on the slope, DO
NOT mow it. Use extra care with grass catchers or other
attachments; these affect the handling and the stability of
the machine.
1. DO NOT operate machine on slopes exceeding 10
degrees (18% grade).
2. Turn blades OFF when traveling uphill. Use a slow
speed and avoid sudden or sharp turns.
3. DO NOT operate machine back and forth across face of
slopes. Operate up and down. Practice on slopes with
blades off.
4. AVOID starting, stopping or turning on slopes. If
machine stops going uphill or tires lose traction, turn
blades OFF and back slowly straight down the slope.
5. STAY ALERT for holes and other hidden hazards. Tall
grass can hide obstacles. Keep away from ditches,
washouts, culverts, fences and protruding objects.
6. KEEP A SAFE DISTANCE (at least two mower widths)
away from edge of ditches and other drop offs. The
machine could turn over if an edge caves in.
7. Always begin forward motion slowly and with caution.
8. DO NOT begin forward motion while the machine is
rolling backwards. A rearward tip-over may result.
9. Use weights or a weighted load carrier in accordance
with instructions supplied with a grass catcher or other
attachments. DO NOT operate machine on slopes
exceeding 10 degrees (18% grade) when equipped with
grass catcher or other attachments.
10. DO NOT put your foot on the ground to try to stabilize
the machine.
11. DO NOT operate machine on wet grass. Reduced
traction could cause sliding.
WARNING
This powerful cutting machine is capable of amputating
hands and feet and can throw objects that can cause
injury and damage! Failure to comply with the following
SAFETY instructions could result in serious injury or
death to the operator or other persons. The owner of the
machine must understand these instructions and must
allow only persons who understand these instructions to
operate machine. Each person operating the machine
must be of sound mind and body and must not be under
the influence of any substance, which might impair vision,
dexterity or judgment.
Carbon Monoxide Warning
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains
carbon monoxide, a poisonous gas that could kill
you in minutes. You CANNOT see it, smell it, or taste
it. Even if you do not smell exhaust fumes, you could
still be exposed to carbon monoxide gas. If you start
to feel sick, dizzy, or weak while using this product,
shut it off and get to fresh air RIGHT AWAY. See a
doctor. You may have carbon monoxide poisoning.
Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for
hours, even after this product has shut off.
ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
Protection for Children
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
machine and the mowing activity. Children who have been
given rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over by the
machine. Never assume that children will remain where you
last saw them.
1. KEEP children out of the mowing area and under the
watchful care of a responsible adult other than the
operator.
2. DO NOT allow children in yard when machine is
operated (even with the blade OFF).
Not For
Reproduction
5
en
12. Choose a low enough speed setting so that you will not
have to stop or shift on a slope. Tires may lose traction
on slopes even though the brakes are functioning
properly.
13. DO NOT operate machine under any condition where
traction, steering or stability is doubtful.
14. Always keep the machine in gear when going down
slopes. DO NOT shift to neutral (or actuate hydro roll
release) and coast downhill.
15. Machine stability is tested in accordance with the
applicable ANSI B71 standard using an operator weight
of 200 lbs. To minimize the risk of a tip-over or roll-over,
operators weighing more than 200 lbs. should further
limit the ground speed and the degree of slope to be
mowed.
Preparation
1. Read, understand, and follow instructions and warnings
in this manual and on the machine, engine and
attachments. Know the controls and the proper use of
the machine before starting.
2. Only mature, responsible persons shall operate the
machine and only after proper instruction.
3. Data indicates that operators age 60 and above, are
involved in a large percentage of mower-related injuries.
These operators should evaluate their ability to operate
the mower safely enough to protect themselves and
others from serious injury.
4. Handle fuel with extra care. Fuels are flammable
and vapors are explosive. Use only an approved fuel
container. DO NOT remove fuel cap or add fuel with
engine running. Add fuel outdoors only with engine
stopped and cool. Clean spilled fuel from machine. DO
NOT smoke.
5. Practice operation of machine with BLADES OFF to
learn controls and develop skills.
6. Check the area to be mowed and remove all objects
such as toys, wire, rocks, limbs and other objects that
could cause injury if thrown by blade or interfere with
mowing.
7. Keep people and pets out of mowing area. Immediately
STOP blades, STOP engine, and STOP machine if
anyone enters the area.
8. Check shields, deflectors, switches, blade controls and
other safety devices frequently for proper operation and
location.
9. Make sure all safety decals are clearly legible. Replace
if damaged.
10. Protect yourself when mowing and wear safety glasses,
a dust mask, hearing protection, long pants and
substantial footwear.
11. Know how to STOP blades and engine quickly in
preparation for emergencies.
12. Use extra care when loading or unloading the machine
into a trailer or truck.
13. Check grass catcher components frequently for signs of
wear or deterioration and replace as needed to prevent
injury from thrown objects going through weak or worn
spots.
Safe Handling of Gasoline
To avoid personal injury or property damage, use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive.
1. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
2. Use only an approved fuel container.
3. DO NOT remove fuel cap or add fuel with the engine
running. Allow the engine to cool before refueling.
4. DO NOT refuel the machine indoors.
5. DO NOT store the machine or fuel container inside
where there is an open flame, spark or pilot light such as
on a water heater or other appliances.
6. DO NOT fill fuel containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always place the
containers on the ground away from the vehicle before
filling.
7. Remove gas-powered equipment from the vehicle or
trailer and refuel it on the ground. If this is not possible,
then refuel equipment using a portable container, rather
than a gasoline dispenser nozzle.
8. DO NOT start gas powered equipment in enclosed
vehicles or trailers.
9. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. DO NOT use a nozzle lock-open device.
10. If fuel is spilled on clothing, change clothing
immediately.
11. Never overfill a fuel tank. Replace fuel cap and tighten
securely.
Operation
1. Mount and dismount machine from left side. Keep clear
of discharge opening at all times.
2. Start engine from operator’s seat, if possible. Make sure
blades are OFF and parking brake is set.
3. DO NOT leave machine with engine running. STOP
engine, STOP blades, SET brake, and remove key
before leaving operators position of any reason.
4. DO NOT operate machine unless properly seated with
feet on feet rests or pedal(s).
Not For
Reproduction
6
5. STOP BLADES and ENGINE and make sure blades
have stopped before removing grass catcher or
unclogging mower to prevent loss of fingers or hand.
6. Blades must be OFF except when cutting grass. Set
blades in highest position when mowing over rough
ground.
7. Keep hands and feet away from rotating blades
underneath deck. DO NOT place foot on ground while
BLADES are ON or machine is in motion.
8. DO NOT operate machine without entire grass
catcher or guards in place and working. DO NOT point
discharge at people, passing cars, windows or doors.
9. Slow down before turning.
10. Watch out for traffic when near or crossing roadways.
11. STOP engine immediately after striking an obstruction.
Inspect machine and repair damage before resuming
operation.
12. Operate machine only in daylight or with good artificial
light.
13. Exercise CAUTION when pulling loads. Limit loads to
those you can safely control and attach loads to hitch
plate as specified with attachment instructions.
14. On slopes, the weight of the towed equipment may
cause loss of traction and loss of control. When towing,
travel slowly and allow extra distance to stop.
15. DO NOT operate engine in enclosed areas. Engine
exhaust gases contain carbon monoxide, a deadly
poison.
16. DO NOT discharge material against a wall or
obstruction. Material may ricochet back towards the
operator.
17. Only use accessories approved by the manufacturer.
See manufacturer’s instructions for proper operation
and installation of accessories.
18. Duration of machine operation may need to be limited
due to exposure to noise and vibration.
19. DO NOT operate machine when the risk of lightning is
present.
Towing
1. Tow only with a machine that has a hitch designed for
towing. DO NOT attach towed equipment except at the
hitch point.
2. Refer to “Towing Implements” in the Operation section
regarding weight limits for towed equipment and towing
on slopes.
3. DO NOT allow children or others on towed equipment.
4. On slopes, the weight of the towed equipment may
cause loss of traction and loss of control. Use caution
while operating on slopes.
5. Travel slowly and allow extra distance to stop.
Maintenance
1. DO NOT store machine or fuel container inside where
fumes may reach an open flame, spark or pilot light
such as in a water heater, furnace, clothes dryer or
other gas appliance. Allow engine to cool before storing
machine in an enclosure. Store fuel container out of
the reach of children in a well ventilated, unoccupied
building.
2. Keep engine and machine free of grass, leaves or
excess grease to reduce fire hazard and engine
overheating.
3. When draining fuel tank, drain fuel into an approved
container outdoors and away from open flame.
4. Check brakes frequently; adjust, repair or replace as
needed.
5. Keep all bolts, nuts and screws properly tight. Check
that all cotter pins are in proper position.
6. Always provide adequate ventilation when running
engine. Exhaust gases contain carbon monoxide, an
odorless and deadly poison.
7. Disconnect negative (black) cable from battery before
performing maintenance or service. Cranking engine
could cause injury.
8. DO NOT work under machine without safety blocks.
9. DO NOT stand unit on end.
10. Service engine and make adjustments only when
engine is stopped. Remove spark plug wire(s) from
spark plug(s) and secure wire(s) away from spark
plug(s).
11. DO NOT change engine governor speed settings or
overspeed engine.
12. Lubricate machine at intervals specified in manual to
prevent controls from binding.
13. Mower blades are sharp and can cut. Wrap the blades
or wear heavy leather gloves and use CAUTION when
handling them.
14. DO NOT test for spark by grounding spark plug next
to spark plug hole; spark plug could ignite gas exiting
engine.
15. Have machine serviced by an authorized dealer at least
once a year and have the dealer install any new safety
devices.
16. Maintain or replace safety and instruction labels as
necessary.
17. Use only factory authorized replacement parts or
equivalent when making repairs.
Not For
Reproduction
7
en
Safety and Instructional Decals - Domestic
Before operating your unit, read and understand the safety
and instructional decals (compare Figure 1 with the table).
The cautions, warnings, and instructions are for your safety.
To avoid personal injury or damage to the unit, understand
and follow all the decals.
WARNING
If any safety or instructional decals become worn or
damaged, and cannot be read, order replacement decals
from your dealer.
F
I
H
G
A
J
C
H
B
D
E
Figure 1
A
Clutch/Brake Operation
Blade Engage
Operation
General Warnings
B
Forward Speed
(Manual Drive Models)
C
Reverse Speed
(Manual Drive Models)
D
Use Caution When
Refueling
E
Transmission Release
(Hydro Drive Models)
F
Weight Limitation
I
Cutting Height
G
Engine Speed
Control
Choke Control
(Select Models)
H
Discharge Safety (2 - 1
on each side of deck)
Not For
Reproduction
8
Safety and Instructional Decals - ANSI Export
Before operating your unit, read and understand the safety
and instructional decals (compare Figure 2 with the table)
A
C
B
Figure 2
A
1
2
3
4
5
6
7
8
B
9
C
10
1. WARNING: Read and understand the Operator’s
Manual before using this machine. Know the location
and function of all controls. Do not operate this machine
unless you are trained.
2. DANGER - LOSS OF TRACTION, SLIDING,
STEERING AND CONTROL ON SLOPES HARZARD:
If machine stops forward motion or starts sliding on a
slope, stop the blades and drive slowly off the slope.
3. DANGER: FIRE HAZARD: Keep unit free of grass,
leaves and excess oil. Do not add fuel while engine is
hot or running. Stop engine, remove key and allow to
cool for at least 3 minutes prior to adding fuel. Do not
add fuel indoors, in an enclosed trailer, garage or other
enclosed areas. Clean up spilled fuel. Do not smoke
while operating this machine.
4. DANGER - TIPPING AND SLIPPING HAZARD: Mow
up and down slopes not across. Do not operate on
slopes over 10 degrees. Avoid sudden and sharp (fast)
turns while on slopes.
5. DANGER - AMPUTATION AND DISMEMBERMENT
HAZARD: To avoid injury from rotating blades and
moving parts, keep safety devices (guards, shields and
switches) in place and working.
6. Do not mow when children or others are around. Never
carry riders especially children even with the blades off.
Do not mow in reverse unless absolutely necessary.
Look down and behind – before and while backing.
7. Consult technical literature before performing technical
repairs or maintenance. When leaving the machine,
shutoff engine, set the parking brake to the lock position
and remove the ignition key.
8. Keep by-standers and children a safe distance away.
Remove objects that can be thrown by the blade. Do not
mow without discharge chute in place.
9. Do not mow without discharge chute or entire grass
catcher in place.
10. To avoid injury from rotating blades, stay clear of deck
edge and keep others away.
Not For
Reproduction
9
en
Features and Controls
Compare the features and controls in Figure 3 with the table
below.
B
Q
C
H
P
D
F
E
G
J I
O
AN
L
M
K
Figure 3
Ref.
Description Icon(s) Icon Definition
A Operator Seat
-- --
B Steering Wheel -
controls direction of
unit
-- --
C
Engine Speed
Control (hidden
from view) - controls
engine speed
Choke on (closed) -
if equipped
Engine speed fast
Engine speed low
D
Cutting Height Adjust
Lever - adjusts
cutting height
Cutting height low
Cutting height high
E Parking Brake Latch
(hidden from view) -
locks brake
Parking brake on
(engaged)
F Blade Control -
engages mower
blade
Blade on (engaged)
Blade off
(disengaged
Ref.
Description Icon(s) Icon Definition
G
Clutch/Brake Pedal
- engages clutch
(manual drive
models) and brake
Clutch engaged
(manual drive
models)
Brake on (engaged)
H
Headlight (not shown;
select models)
-- --
I
Mulching Cover
-- --
J
Ignition Switch -
starts engine
Engine off
Engine on (run)
Engine start
K
Transmission
Release Lever
(hidden from view;
hydro drive models) -
releases transmission
so unit can roll freely
Transmission
engaged (locked)
Transmission
released (unlocked)
L
Reverse Mowing
Switch - temporarily
allows mower blade
to operate with
transmission in
reverse
-- --
M
Recoil Start Handle
(hidden from view)
-- --
N
Transmission Shift
Lever (manual drive
models) - selects
transmission speed
and direction
Forward ground
speed
Neutral (no ground
speed)
Reverse ground
speed
O
Fuel Tank
-- --
P
Forward Ground
Speed Pedal (hydro
drive models) -
controls forward
ground speed
Forward ground
speed
Q
Reverse Ground
Speed Pedal (hydro
drive models) -
controls reverse
ground speed
Reverse ground
speed
Not For
Reproduction
10
Safety Interlock Systems Checks
WARNING
DO NOT operate machine if any safety interlock or safety
device is not in place and functioning properly. Contact
your dealer immediately for assistance. DO NOT attempt
to defeat, modify or remove any safety device.
Engine must not start if:
1. The Clutch/Brake Pedal is not fully depressed OR,
2. The Blade Control is in the ON (engaged) position.
Engine should start if:
1. The Blade Control is in the OFF (disengaged) position
AND,
2. The Clutch/Brake Pedal is fully depressed.
Engine and blade must stop if:
1. The operator rises off of the operator seat while the
Blade Control is in the ON (engaged) position OR,
2. The operator rises off of the operator seat while the
Clutch/Brake Pedal is not fully depressed OR,
3. The operator attempts to drive the unit in reverse with
the mower blade engaged and the reverse mowing
option function (RMO) not activated.
WARNING
Once mower blade is disengaged, it should come
to a complete stop in 5 seconds or less. If the blade
continues to rotate after 5 seconds, DO NOT operate the
machine. Return the machine to an authorized dealer for
adjustment.
Operation
Before Starting
Make the following checks and perform the service required
before each start-up:
1. Check the tire pressure; add or release air as
needed. Refer to “How To Check Tire Pressure” in the
Maintenance section.
2. Check guards, deflectors and covers to make sure all
are in place and securely tightened.
3. Check engine oil and add oil as needed. Refer to “How
To Check/Add Oil”.
4. Add fuel to the fuel tank as needed. Refer to “How to
Add Fuel”.
5. Adjust the operator seat as needed to the most
comfortable position. Refer to “How To Adjust The
Operator Seat”.
6. Check all operator controls to ensure they operate freely
without binding.
7. Perform the Safety Interlock System Checks. Refer to
“Safety Interlock System Checks”.
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF,
SG, SH, SJ or higher. Do not use special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
SAE 30 *
10W-30
Synthetic 5W-30
5W-30
A
B
C
D
A SAE 30 - Below 40°F (4°C) the use of SAE 30 will
result in hard starting.
B 10W-30 - Above 80°F (27°C) the use of 10W-30 may
cause increased oil consumption. Check oil level
more frequently.
C Synthetic 5W-30
D 5W-30
Not For
Reproduction
11
en
How To Check/Add Oil
Before adding or checking the oil
Place engine level.
Clean the oil fill area of any debris.
1. Remove the dipstick (A, Figure 4) and wipe with a clean
cloth.
NOTE:
On some models, the dipstick is accessible through an
opening behind the operator seat.
2. Insert and tighten the dipstick.
3. Remove the dipstick and check the oil level. It should be
at the top of the full indicator (B) on the dipstick.
4. If low, add oil slowly into the engine oil fill (C). Do not
overfill. After adding oil, wait one minute and then
recheck the oil level.
5. Replace and tighten the dipstick.
B
A
A
C
Figure 4
Fuel Recommendations
Fuel must meet these requirements:
Clean, fresh, unleaded gasoline.
A minimum of 87 octane/87 AKI (91 RON). High altitude
use, see below.
Gasoline with up to 10% ethanol (gasohol) is
acceptable.
NOTICE: Do not use unapproved gasolines, such as E15
and E85. Do not mix oil in gasoline or modify the engine to
run on alternate fuels. Use of unapproved fuels will damage
the engine components, which will not be covered under
warranty.
To protect the fuel system from gum formation, mix a fuel
stabilizer into the fuel. See Storage. All fuel is not the
same. If starting or performance problems occur, change
fuel providers or change brands. This engine is certified to
operate on gasoline.
The emissions control system for this engine is EM (Engine
Modifications).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 85
octane/85 AKI (89 RON) gasoline is acceptable.
For carbureted engines, high altitude adjustment is
required to maintain performance. Operation without this
adjustment will cause decreased performance, increased
fuel consumption, and increased emissions. Contact a
Briggs & Stratton Authorized Service Dealer for high altitude
adjustment information. Operation of the engine at altitudes
below 2,500 feet (762 meters) with the high altitude
adjustment is not recommended.
For Electronic Fuel Injection (EFI) engines, no high altitude
adjustment is necessary.
Not For
Reproduction
12
How To Adjust The Operator Seat
With the engine stopped:
1. Raise the operator seat.
2. Loosen the two adjusting knobs (A, Figure 6) and
move the seat to the desired position. After adjustment,
tighten the knobs securely.
3. Lower the operator seat.
A
Figure 6
How To Add Fuel
WARNING
Fuel and its vapors are extremely flammable and
explosive. Fire or explosion can cause severe burns or
death.
When Adding Fuel
Turn engine off and let engine cool at least 5 minutes
before removing the fuel cap.
Fill fuel tank outdoors or in well-ventilated area.
Do not overfill fuel tank. To allow for expansion of the
fuel, do not fill above the bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
Check fuel lines, tank, cap, and fittings frequently for
cracks or leaks. Replace if necessary.
If fuel spills, wait until it evaporates before starting
engine.
1. Clean the fuel cap area of dirt and debris. Remove the
fuel cap (A, Figure 5).
2. Fill the fuel tank with fuel. To allow for expansion of the
fuel, do not fill above the bottom of the fuel tank neck
(B).
3. Reinstall the fuel cap.
B
A
Figure 5
Not For
Reproduction
13
en
How To Start The Engine
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains
carbon monoxide, a poisonous gas that could kill
you in minutes. You CANNOT see it, smell it, or taste
it. Even if you do not smell exhaust fumes, you could
still be exposed to carbon monoxide gas. If you start
to feel sick, dizzy, or weak while using this product,
shut it off and get to fresh air RIGHT AWAY. See a
doctor. You may have carbon monoxide poisoning.
Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially
being drawn towards occupied spaces.
Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for
hours, even after this product has shut off.
ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
Electric Start:
1. Sit squarely in the operator seat.
2. Manual Drive Models - Move the transmission shift lever
to the Neutral (‘N’) position. Refer to “How To Engage
The Transmission”.
WARNING
DO NOT start the engine with the transmission shift lever
in a drive position. Follow starting instructions carefully.
3. Make sure the Blade Control (A, Figure 7) is in the OFF
position.
A
Figure 7
4. Fully depress the Clutch/Brake Pedal (A, Figure 8).
A
Figure 8
5. Move the engine speed control (A, Figure 9) to the
FAST position (or CHOKE position, if equipped).
NOTE: The CHOKE position is not required when starting
a warm engine.
A
Figure 9
Not For
Reproduction
14
6. Insert the ignition key (A, Figure 10) into the ignition
switch. Turn the key to the START position until the
engine starts.
NOTE: When the ignition key is turned to START, the
engine will turn over, but will not start unless the Clutch/
Brake pedal is fully depressed and the Blade Control is in
the OFF position.
A
Figure 10
NOTE: If after 5 seconds of cranking the engine does not
start, release the key, make sure the Clutch/Brake Pedal is
fully depressed, and attempt starting again after waiting for
approximately 20 seconds.
7. After the engine starts, move the engine speed control to
the FAST position (if equipped with choke) and allow a
brief warm-up until engine runs smooth.
NOTE: Always operate with the engine speed control in the
FAST position.
NOTE: The headlight (featured on select models) is opera-
tional any time the ignition switch is in the RUN or START
position.
Recoil Start:
1. Manual Drive Models - Move the transmission shift lever
to the Neutral (‘N’) position. Refer to “How To Engage
The Transmission”.
WARNING
DO NOT start the engine with the transmission shift lever
in a drive position. Follow starting instructions carefully.
2. Make sure the Blade Control (A, Figure 7) is in the OFF
position.
3. Set the parking brake. Refer to “How To Set The Parking
Brake”.
4. Move the engine speed control (A, Figure 9) to the
FAST position (or CHOKE position, if equipped).
NOTE: The CHOKE position is not required when starting
a warm engine.
5. Insert the ignition key (A, Figure 11) into the ignition
switch. Turn the key to the RUN position (B).
A
B
Figure 11
6. Grasp the recoil start handle on the engine (A, Figure
12) and pull briskly until the engine starts.
7. After the engine starts, move the engine speed control
to the FAST position (if equipped with choke) and allow
a brief warm-up period until engine runs smooth.
NOTE: Always operate with the engine speed control in the
FAST position.
NOTE: The headlight (featured on select models) is opera-
tional any time the ignition switch is in the RUN position.
A
Figure 12
Not For
Reproduction
15
en
How To Engage The Mower Blade
1. Start the engine.
2. Move the blade control (A, Figure 13) to the ON position.
A
Figure 13
How To Engage The Transmission
Manual Drive Models:
1. Start the engine.
2. To move forward:
Depress the clutch/brake pedal (A, Figure 8).
Move the transmission shift lever (A, Figure 14) from
the Neutral (‘N’) position (B) into the first forward speed
notch (C).
Release the clutch/brake pedal to begin forward motion.
During forward motion, the transmission shift lever may
be placed in any desired forward speed (D) without
depressing the clutch/brake pedal.
A
B C
D
E
Figure 14
3. To move backward:
Depress the clutch/brake pedal (A, Figure 8).
Move the transmission shift lever (A, Figure 14) from the
Neutral (‘N’) position (B) into the reverse speed slot (E).
During reverse motion, the transmission shift lever
may be placed in any desired reverse speed without
depressing the clutch/brake pedal.
Hydro Drive Models:
1. Start the engine.
2. Make sure the parking brake is released. Refer to “How
To Set The Parking Brake”.
3. To move forward:
Slowly depress the forward ground speed pedal (A,
Figure 15) to begin forward motion. Increase ground
speed by further depressing the pedal.
4. To move backward:
Slowly depress the reverse ground speed pedal (B) to
begin reverse motion. Increase ground speed by further
depressing the pedal.
NOTE: For best cutting results, choose a slow forward
speed with the engine speed control in the FAST position.
This combination will allow the mower blade to lift the grass
while cutting smoothly and evenly.
NOTICE: If the transmission is moved into reverse while the
mower blade is engaged, the engine will shut off. If mowing
in reverse is necessary, refer to “Reverse Mowing Option
(RMO)”.
WARNING
LOOK and SEE behind and down for children, pets and
hazards before and while backing.
B A
Figure 15
Not For
Reproduction
16
WARNING
DO NOT leave the machine with the engine running.
STOP Blade. STOP engine. Shift to neutral and engage
parking brake. Remove key.
How To Stop The Engine, Transmission And
Mower Blade
Engine
1. Stop the engine by turning the ignition key (A, Figure 16)
to the OFF position.
2. Remove the key.
A
Figure 16
Transmission
Manual Drive Models:
1. Stop motion of the unit by fully depressing the clutch/
brake pedal (A, Figure 8) to disengage the clutch and
apply the brake.
2. Return the transmission shift lever to the Neutral (‘N’)
position. Refer to “How To Engage The Transmission”.
Hydro Drive Models:
1. Stop motion of the unit by fully releasing the ground
speed pedals (A, Figure 17). Additional braking can be
achieved by depressing the brake pedal (A, Figure 8).
A
Figure 17
Mower Blade
1. Stop the mower blade by moving the blade control (A,
Figure 7) to the OFF position.
WARNING
Once blade is disengaged, it should come to a complete
stop in 5 seconds or less. If the blade continues to rotate
after 5 seconds, the blade brake must be adjusted.
Return machine to an authorized dealer for adjustment.
DO NOT CONTINUE to operate machine until blade
brake is adjusted and functioning properly.
How To Set The Parking Brake
1. Fully depress the clutch/brake pedal (A, Figure 18).
2. Slide the parking brake latch (B) up and hold while
releasing the clutch/brake pedal. The parking brake is now
set.
B
A
Figure 18
3. To release the parking brake, fully depress the clutch/
brake pedal. The parking brake will release automatically.
WARNING
DO NOT park the machine on slopes.
Not For
Reproduction
17
en
How To Adjust The Cutting Height
1. Raise or lower the cutting height adjust lever (A, Figure
19) into the desired height of cut notch.
A
Figure 19
Reverse Mowing Option (RMO)
WARNING
Mowing in reverse can be hazardous to bystanders.
Tragic accidents can occur if the operator is not alert to
the presence of children. Never activate RMO if children
are present. Children are often attracted to the unit and
the mowing activity.
1. Engage the mower blade. Refer to “How To Engage The
Mower Blade”.
2. Insert the supplied key (A, Figure 20) into the RMO
switch (B), and turn the key to activate the RMO
function. The LED light (C) indicates that the RMO
function is now activated.
3. Engage the transmission in reverse. Refer to “How To
Engage The Transmission”.
4. The RMO function is deactivated when the mower blade
is disengaged.
C
A
B
Figure 20
How To Install The Discharge Deflector
WARNING
DO NOT attempt any adjustments, maintenance, service
or repairs with the engine running.
STOP engine.
STOP blade.
Engage parking brake.
Remove key.
Remove spark plug wire from spark plug and secure
away from plug.
Engine and components are HOT. Avoid serious
burns, allow all parts to cool before working on
machine.
1. Remove the nut and washer (A, Figure 21) securing the
bottom edge of the mulching cover (B) to the mower
deck.
A
B
Figure 21
Not For
Reproduction
18
Hydro Drive Models:
1. Make sure the unit is parked on a flat, even surface.
2. Release the parking brake, if set. Refer to “How To Set
The Parking Brake”.
3. Move the transmission release lever (located behind
the right rear tire) out and down into the locking slot (A,
Figure 23) to disengage the transmission.
4. The unit can now be pushed by hand.
5. After moving the unit to the desired location, move the
transmission release lever up and in (B) to engage the
transmission.
A
B
Figure 23
Towing A Trailer
The maximum horizontal drawbar force allowed is 34 lbs
(150N) *.
The maximum vertical drawbar force is 20 lbs (90 N) *.
* Approximate
2. Raise the mulching cover. Replace the washer and nut
onto the retaining bolt in the deck, tightening securely.
3. Install the discharge deflector (A, Figure 22) to the
mower deck, making sure that the slots (B) in the
deflector fit over the locking tabs (C) on the mulching
cover hinge bracket.
4. Lower the mulching cover.
5. To remove the discharge deflector:
Raise the mulching cover.
Lift and remove the discharge deflector from the mower
deck.
Remove the nut and washer from the retaining bolt in
the deck.
Lower the mulching cover, securing with the washer and
nut. Tighten securely.
B
C
A
Figure 22
How To Push The Unit By Hand
Manual Drive Models:
1. Make sure the unit is parked on a flat, even surface.
2. Make sure the transmission shift lever is in the
Neutral (N) position. Refer to “How To Engage the
Transmission”.
3. Release the parking brake, if set. Refer to “How To Set
The Parking Brake”.
4. The unit can now be pushed by hand. Be sure to set
the parking brake after the unit is moved to the desired
location.
Not For
Reproduction
19
en
Maintenance
WARNING
DO NOT attempt any adjustments, maintenance, service
or repairs with the engine running.
STOP engine.
STOP blade.
Engage parking brake.
Remove key.
Remove spark plug wire from spark plug and secure
away from plug.
Engine and components are HOT. Avoid serious burns,
allow all parts to cool before working on machine.
Maintenance Schedule
RIDER
Every 8 Hours or Daily
• Check safety interlock system
• Clean debris off rider
• Clean debris from engine area
Every 25 Hours or Annually *
• Check tire pressure
• Check mower blade stopping time
• Check rider for loose hardware
Every 50 Hours or Annually *
• Clean battery and cables
• Check brakes
See Dealer Annually to
• Lubricate rider
• Check mower drive belts
• Check mower blades **
* Whichever comes first
** Check blades more often in regions with sandy soils or
high dust conditions.
Rider Maintenance (Basic)
How To Check The Safety Interlock System
Refer to “Safety Interlock System Checks” in the Operation
section.
How To Clean The Rider And Mower Deck
WARNING
Wear heavy leather gloves when handling or working
around cutting blades. Blades are extremely sharp and
can cause severe injury.
1. Raise the mower deck to the highest cutting position.
Refer to “How To Adjust The Cutting Height”.
2. Clean the underside of the mower deck, removing all
accumulation of grass clippings and debris.
3. Clean the top of the deck, removing all grass clippings
and debris.
4. Use a brush or compressed air to remove loose debris
from the rider.
How To Clean The Engine
Use a brush or compressed air to remove loose debris on
or around the engine.
How To Check Tire Pressure
Use a tire gauge to check the tire pressure; add or release
air as needed. Refer to “Product Specifications” for correct
pressure.
Not For
Reproduction
20
How To Check Mower Blade Stopping Time
WARNING
The following procedure requires the engine and blades
to be operated. Exercise extreme caution. Clear area of
loose parts & tools first. Only operate blades when seat-
ed in the operator’s seat.
1. Start the engine.
2. Engage the mower blade.
3. Disengage the mower blade. The blade should stop
rotating in 5 seconds or less after moving the blade
control to the OFF position.
WARNING
Blade must stop rotating in 5 seconds or less after the
blade has been turned off. DO NOT operate machine.
Contact an authorized dealer for adjustment.
4. If the blade continues to rotate longer than 5 seconds,
do not operate the machine. Contact an authorized
dealer for assistance.
NOTE: Any adjustments and service regarding mower
blade stopping time should be performed by an authorized
dealer.
How To Perform Battery Service
Refer to “Battery Service”.
How To Check The Brake / Parking Brake
1. Check the machine brake for proper function:
Engage the parking brake, and push the machine. The
rear tires should skid.
Drive the machine forward and apply the brake. The
machine should come to a complete stop in less than 5
feet (1,5 meters).
2. If the brakes are not functioning properly, do not oper-
ate the machine. Contact an authorized dealer for ser-
vice.
Rider Maintenance (Advanced)
WARNING
DO NOT stand the unit on end. Attempting to do so may
cause an unstable condition, resulting in serious injury or
equipment damage.
Shift Lever (Manual Drive Models)
Lubricate the shift lever grease fitting (A, Figure 24) with
two shots of general purpose grease from a grease gun.
A
Figure 24
Rear Axle Bearing (Manual Drive Models)
1. The grease fitting (A, Figure 25) on the left rear axle
bearing requires three shots of general purpose grease
from grease gun.
2. The right rear axle bearing is lubricated by the
differential lubricant and requires no grease.
A
Figure 25
Differential / Chain Case (Manual Drive Units)
Lubrication of the differential and chain case should be
performed by an authorized dealer.
Mower Blade Spindle
The mower blade spindles used on these units are
equipped with sealed spindle bearings, which do not
require lubrication.
Mower Deck Linkage
See your authorized dealer for lubrication of mower deck
linkage pivot points.
Not For
Reproduction
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Simplicity 7800954-01 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur