Sony SCD-C333ES Manuel utilisateur

Marque: Sony

Modèle: SCD-C333ES

Catégorie: Lecteur CD

Taper: Manuel utilisateur

4-230-687-12(1)

Super Audio CD

Player

 2000 Sony Corporation

SCD-C333ES

Operating Instructions

Mode d’emploi

WARNING

To prevent fire or shock

hazard, do not expose the

unit to rain or moisture.

Welcome!

Thank you for purchasing the Sony Super

Audio CD Player. Before operating the

unit, please read this manual thoroughly

and retain it for future reference.

About This Manual

The instructions in this manual are for

model SCD-C333ES.

Conventions

• Instructions in this manual describe the

controls on the player.

You can also use the controls on the

remote if they have the same or similar

names as those on the player.

• The following icons are used in this

manual:

Indicates that you can do the

task using the remote.

Indicates hints and tips for

making the task easier.

This symbol is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a

risk of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

The shielded interface cable recommended

in this manual must be used with this

equipment in order to comply with limits

for a digital device pursuant to Subpart B

of Part 15 FCC Rules.

For the customers in the United States

CAUTION

You are cautioned that any changes or

modification not expressly approved in this

manual could void your authority to

operate this equipment.

Owner’s Record

The model and serial numbers are located

at the rear of the unit.

Record the serial number in the space

provided below. Refer to them whenever

you call upon your Sony dealer regarding

this product.

Model No. SCD-C333ES

Serial No. _________________________

The following caution label is located

inside the unit.

For the customers in Canada

CAUTION

TO PREVENT ELECTRIC SHOCK, DO

NOT USE THIS POLARIZED AC PLUG

WITH AN EXTENSION CORD,

RECEPTACLE OR OTHER OUTLET

UNLESS THE BLADES CAN BE FULLY

INSERTED TO PREVENT BLADE

EXPOSURE.

Features

Playback of the Super Audio CD recorded

in the DSD format

The DSD (Direct Stream Digital) format is the core

technology of a Super Audio CD, allowing music

reproduction that is extremely faithful to the original

sound.

The DSD format, using a 2.8224 MHz sampling frequency

64 times higher than that of a conventional CD, and the 1-

bit quantization, makes possible recording of more than

four times the data information of the PCM format which

is used for a conventional CD.

Different from the PCM format which performs data

decimation and interpolation via digital filters, the DSD

format adopts the simple playback process. In other

words, the A/D converted 1-bit digital signal only passes

through an analog low-pass filter before playback.

As a whole, the DSD format achieves both a wide

frequency range of, theoretically, over 100 kHz, and a

wide dynamic range across the audible frequency range

resulting in high-quality music reproduction faithful to

the original sound.

To play back a Super Audio CD recorded in the DSD

format with exceptional quality, the SCD-C333ES employs

a newly developed DSD decoder and a D/A converter

system, as well as a chassis and loading mechanism

especially designed for this unit.

Playback of a conventional CD with

higher quality

The SCD-C333ES can also play back a conventional CD

with higher quality than a conventional CD player. To

provide enhanced quality, the SCD-C333ES employs

various advanced technologies. For example, a 24-bit

precision variable coefficient (V.C.) digital filter is

provided for CD playback (see page 20). By selecting one

of five filters which have different cutoff characteristics,

you can adjust the tone quality in accordance with the

music source or your audio system.

Others

• A Super Audio CD can mark up to 255 track numbers.

This feature applies to SCD-C333ES.

• The supplied remote is capable of controlling either the

SCD-C333ES and a conventional Sony CD player.

TABLE OF CONTENTS

Getting Started 4

Before You Start the Hookup 4

Hooking Up the Audio Components 5

Location and Functions of Parts 6

Front Panel Parts Descriptions 6

Rear Panel Parts Descriptions 8

Remote Parts Descriptions 9

Playing Discs 10

Compatible Disc Types 10

Playing a Disc 11

Using the Display 13

Replacing Discs While Playing a Disc 15

Locating a Specific Disc 15

Locating a Specific Track 16

Locating a Particular Point in a Track 16

Playing Tracks Repeatedly 17

Playing Tracks in Random Order (Shuffle Play) 18

Creating Your Own Program (Program Play) 19

Listening to a CD Using a Filter (Digital Filter

Function) 20

Storing Information About CDs 22

What You Can Do With the Disc Name 22

Labeling Discs (Disc Name) 23

Additional Information 25

Precautions 25

Notes on Discs 26

Troubleshooting 27

Specifications 27

Index 28

Getting

Started

This chapter provides information on

the supplied accessories and how to

connect various audio components to

the Super Audio CD player. Be sure

to read this chapter thoroughly before

you actually connect anything to the

player.

Before You Start the

Hookup

Checking the supplied accessories

This player comes with the following items:

• Audio connecting cord

(phono jack × 2 y phono jack × 2) (1)

• Remote commander (remote) RM-SC300 (1)

• R06 (size-AA) batteries (2)

• CONTROL A1 cord (1)

Inserting batteries into the remote

Insert two R06 (size-AA) batteries into the battery

compartment with the + and – correctly oriented to the

markings. When using the remote, point it at the remote

sensor

on the player.

When to replace the batteries

Under normal conditions, the batteries should last for about six

months. When the remote no longer operates the player, replace

both batteries with new ones.

Notes

• Do not leave the remote in an extremely hot or a humid place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not use a new battery with an old one.

• Do not expose the remote sensor to direct sunlight or lighting

apparatus. Doing so may cause a malfunction.

• If you do not intend to use the remote for an extended period

of time, remove the batteries to avoid possible damage from

battery leakage and corrosion.

Getting Started

Hooking Up the Audio Components

Stereo amplifier, etc.

About the CONTROL A1 jack

If you have a Sony component with the CONTROL A1 (or

CONTROL A1) jack

Connect the component via the CONTROL A1 (or CONTROL

A1) jack with a monaural (2P) mini-plug cord. You can simplify

the operation of audio systems composed of separate Sony

components. For details, refer to the supplementary “CONTROL

A1 Control System” instructions.

When using another Sony CD player in conjunction with this

player

You can set the supplied remote to be effective on this player

only.

• If the other player’s command mode can be set:

Set the CD1/2 switch of this player’s remote to CD1 (factory

setting), and set the other player’s remote to CD2.

• If the other player’s command mode cannot be set:

Set the CD1/2 switch of this player’s remote to CD2.

If you connect this player with another Sony CD player, you

have to set the command mode of each player.

To set the command mode of this player:

1 Press MENU.

2 Turn l AMS L to select “COMMAND MODE.”

3 Push l AMS L.

The current command mode appears.

4 Turn l AMS L to select CD1 or CD2, then push

l AMS L again.

Connecting the AC power cord

Connect the AC power cord to a wall outlet.

Transporting the player

Before transporting the player, follow the procedure below to

return the internal mechanisms back to their original position.

1 Remove all the discs from the disc tray.

2 Press A OPEN/CLOSE to close the disc tray.

“NO DISC” appears in the display.

3 Wait for 10 seconds, then press POWER to turn off

the player.

White (L)

Red (R)

White (L)

Red (R)

Connect the Super Audio CD player to an audio

component. Be sure to turn off the power of all

components before making connections and connect

securely to prevent noise.

Connecting via ANALOG OUT jacks

Use an audio connecting cord for this connection. Be sure to

match the colour-coded pin to the appropriate jacks: white (left)

to white and red (right) to red.

Audio connecting cord (supplied)

Connecting via DIGITAL (CD) OUT OPTICAL

connector

Use an optical digital cable for this connection. When connecting

the optical digital cable to the DIGITAL (CD) OUT OPTICAL

connector, take the cap off the connectors and push the cable

plugs in until they click into place.

Be careful not to bend or twist the optical cable.

Optical digital cable (not supplied)

Note

Only the audio signals of conventional CDs can be output from

the DIGITAL (CD) OUT connectors. Those of the Super Audio

CD cannot be output through DIGITAL (CD) OUT.

Connecting via DIGITAL (CD) OUT COAXIAL

connector

Use a coaxial digital cable to connect the audio components

equipped with coaxial digital input connectors.

Coaxial digital cable (not supplied)

Note

Only the audio signals of conventional CDs can be output from

the DIGITAL (CD) OUT connectors. Those of the Super Audio

CD cannot be output through DIGITAL (CD) OUT.

OUT

ANALOG

CONTROL

ΙΙ

OUT

DIGITAL CD

COAXIALOPTICAL

INPUT

1 POWER switch (11)

Press to turn on/off the player.

2 Remote sensor

(4)

3 DISC 1–5 button (12)

Press to select the disc.

4 SACD/CD button (with an LED) (10)

Each time you press the button while the Hybrid disc

(page 11) is loaded, the layer changes between an HD

layer (the LED turns on) and CD layer (the LED turns

off).

5 Display window (13)

Shows various information.

6 N button (12)

Press to start play.

N indicator

Lights up during playback.

7 X button (12)

Press to pause play.

X indicator

Lights up during pause.

Location and

Functions of

Parts

This chapter tells you about the

location and functions of the various

buttons and controls on the front and

rear panels and the supplied remote.

Further details are provided on the

pages indicated in parentheses.

It also tells you about the information

that appears in the display window.

Front Panel Parts

Descriptions

Location and Functions of Parts

8 x button (12)

Press to stop play.

9 EX-CHANGE button (15)

Press to replace discs while playing a disc.

0 CHECK button (19)

Press to check the programmed order.

qa lAMSL dial (AMS: Automatic Music Sensor)

(12)

When you turn the lAMSL dial

counterclockwise by one click, you go back to the

preceding track; when you turn the lAMSL dial

clockwise by one click, you go to the succeeding track.

qs CLEAR button (20)

Press to delete a programmed track number.

qd DISC SKIP button (11)

Press to select the disc.

qf PHONE LEVEL control

Adjust the headphones volume.

qg PHONES jack

Connect the headphones.

POWER

PHONES

LEVEL

MIN MAX

AMS

PUSH ENTER

SACD

CHECK CLEAR

DISC SKIPEX-CHANGE

DISC 1

CONTINUE

DISC 2

SHUFFLE

DISC 3

PROGRAM

DISC 4

DISC 5

TIME/TEXT

OPEN/CLOSE

qh A OPEN/CLOSE button (11)

Press to open/close the disc tray.

qj Disc tray (11)

Press A OPEN/CLOSE to open/close the disc tray.

qk TIME/TEXT button (13)

Each time you press the button, the playing time of the

track, the total remaining time on the disc, or TEXT

information appears in the display.

ql MENU button (5)

Press to enter the menu.

w; PROGRAM button (19)

Press to select Program Play.

wa SHUFFLE button (18)

Press to select Shuffle Play.

w; CONTINUE button (12)

Press to resume normal play from Shuffle Play or

Program Play.

Location and Functions of Parts

Rear Panel Parts Descriptions

1 ANALOG OUT jacks (5)

Connect to an audio component using the audio

connecting cord.

2 DIGITAL (CD) OUT OPTICAL connector (5)

Connect to an audio component using an optical

digital cable.

3 DIGITAL (CD) OUT COAXIAL connector (5)

Connect to an audio component using the coaxial

digital cable.

4 CONTROL A1

jack (5)

Connect to the Sony audio component using the

monaural (2P) mini-plug cord.

Note

Only the audio signals of the CD can be output from the

DIGITAL (CD) OUT connectors shown in 2 and 3. Those of

the Super Audio CD cannot be output through DIGITAL (CD)

OUT.

OUT

ANALOG

CONTROL

ΙΙ

OUT

DIGITAL (CD)

COAXIALOPTICAL

Location and Functions of Parts

Remote Parts Descriptions

CONTINUE SHUFFLE

PLAY MODE

PROGRAM

123

456

10/0

SPACE

TIME/TEXT

CAPS

DISC

REPEAT CHECK

AMS

CLEAR

INPUT

NAME

SACD/CD

>10 ENTER

MODE

DISPLAY

FILTER

DIGITAL

DISC SKIP

–+

CD1

ABC DEF&,!,?

JKL MNOGHI

TUV WXYZPQRS

CD2

1 CONTINUE button (12)

Press to resume normal play from Shuffle Play or

Program Play.

SHUFFLE button (18)

Press to select Shuffle Play.

PROGRAM button (19)

Press to select Program Play.

2 DIGITAL FILTER button (20)

Press to select the digital filter type when a CD is

played.

3 DISC/CAPS button (15, 23)

Press to select the disc.

Press to select the capital letter.

4 Number buttons (15)

Press to enter the track numbers.

10 button (16)

Press to locate a track numbered over 10.

6 REPEAT button (17)

Press repeatedly to play all tracks or only one track on

the disc.

7 NAME INPUT button (23)

Press to enter the name input mode.

8 H button (12)

Press to start play.

X button (12)

Press to pause play.

x button (12)

Press to stop play.

9 AMS ./> (AMS: Automatic Music Sensor)

buttons (16)

Press to locate a specific track.

0 m/M buttons (16)

Press to locate a portion you want to play within a

track.

qa DISC SKIP +/– buttons (11)

Press to select the disc.

qs CD1/2 (COMMAND MODE) switch (5)

Select the command mode.

qd DISPLAY MODE button (13)

Press to turn off the information.

qf TIME/TEXT/SPACE button (13, 23)

Each time you press the button, the playing time of the

track, the total remaining time on the disc, or TEXT

information appears in the display.

Press to insert a space.

qg ENTER button (23)

Press to decide the selection.

qh CLEAR button (19)

Press to delete a programmed track number.

qj CHECK button (19)

Press to check the programmed order.

qk SACD/CD button (10)

Each time you press the button while the Hybrid disc

(page 11) is loaded, the layer changes between an HD

layer (the SACD/CD LED turns on) and CD layer (the

SACD/CD LED turns off).

Compatible Disc Types

You can play the following discs with this player.

Depending on the type of disc to be played, select the

appropriate indicator by pressing SACD/CD on the

remote (pages 11).

Super Audio CD (single layer disc)

This disc consists of a single HD layer*.

Press SACD/CD repeatedly so that “SACD” appears in

the display (the SACD/CD LED turns on).

*High density signal layer for the Super Audio CD

Super Audio CD (dual layer disc)

This disc consists of dual HD layers and is capable of

extended play over long periods.

Press SACD/CD repeatedly so that “SACD” appears in

the display (the SACD/CD LED turns on).

Also, as the dual layer disc consists of dual HD layers on

one side only, it is not necessary to turn the disc over.

Conventional CD

This disc is the standard format.

Press SACD/CD repeatedly so that “CD” appears in the

display (the SACD/CD LED turns off).

HD (high density) layer

HD layer

CD layer

Playing Discs

This chapter explains the various

ways to play discs.

Playing Discs

Playing a Disc

The operations for normal play and the basic operations

during play are explained below.

1 Turn on the amplifier. Turn down the volume level

to the lowest.

2 Select the player position using the input selector

on the amplifier.

3 Press POWER to turn on the player.

4 Press A OPEN/CLOSE to open the disc tray, and

place a disc on the tray.

5 To place other discs, press DISC SKIP and place the

discs in the order you want to play.

Each time you press the button, the disc tray turns and

you can place the discs in the empty disc

compartments. The player plays the disc in front of

you first.

CD layer

HD layer

Super Audio CD + CD (Hybrid disc)

This disc consists of an HD layer and a CD layer. Press

SACD/CD to select the layer you want to listen to. Also,

as the dual layers are on one side, it is not necessary to

turn the disc over. You can play the CD layer using a

conventional CD player.

Incompatible Discs

This player cannot play the following discs. If you try to

play them, the error message “TOC Error” or “NO DISC”

will appear or there will be no sound.

• CD-ROM

• DVD, etc.

lAMSL

POWER

A OPEN/CLOSE

With the label side up

CONTINUE

Disc number

SACD/CD

DISC SKIP

Playing Discs

Basic operations during play

To Press

Stop play x

Pause play X

Resume play after pausing X or N

Locate a succeeding track Turn lAMSL clockwise

Locate the beginning of the Turn lAMSL

current track or a preceding counterclockwise

track

Go to the next disc DISC SKIP

Select a disc directly DISC 1–5

Eject the disc A OPEN/CLOSE

You can select the disc you want to start playing first

Press one of the DISC 1–5 buttons.

To select a layer you want to listen to when playing a hybrid

disc (page 11)

After you stop play using x, press SACD/CD repeatedly to light

either the “SACD” or “CD”.

The selected layer is effective until you play another disc or turn

the player off. When you select another disc (even if you select

the same disc), the player selects an HD layer automatically

(default layer).

To select the CD layer automatically when you play a Hybrid

disc, change the default layer as follows:

1 Press MENU.

2 Turn lAMSL to select “LAYER SELECT.”

3 Push lAMSL.

The current default layer appears.

4 Turn lAMSL to select CD or SACD, then push

lAMSL again.

Note

During playback, increase the volume level gradually starting

from the lowest level. The output from this unit may contain

band width that are out of the normal listening range. This may

cause damage to the speakers or ears.

6 Press CONTINUE to select ALL DISCS or 1 DISC

Continuous Play mode.

Each time you press the CONTINUE button, “ALL

DISCS” or “1 DISC” appears in the display.

7 Press SACD/CD to select the SACD or CD.

Each time you press the button, the SACD or CD

appears alternately in the display. Select the type of

disc on the tray. For details, see page 10.

8 Press N.

Playback starts from the first track. If you want to start

playing from a specific track, turn lAMSL to

select the track number before pressing N.

9 Adjust the volume on the amplifier.

Playing a Disc

When you select

ALL DISCS

1 DISC

The player plays

All discs in the player consecutively in

the order of disc number

Only the disc you’ve selected

Playing Discs

Using the Display

The display window shows various information about the

disc or track being played. This section describes the

information that appears for each play status.

Displaying information while the player is

stopped

Press TIME/TEXT.

The display shows the current disc number, total number

of tracks, total playing time, and music calendar on the

disc.

TIME/TEXT

DISPLAY MODE

Total playing time

Current disc number

DISCSALL

110 1 45.57

SACD

DISC TRACK INDEX MIN SEC

12345

678910

12345

Music calendar

Displaying information while the player is

playing

Press TIME/TEXT.

Each time you press the button, the current track number

and its elapsed time or remaining time appears, or the

total remaining time for the disc appears in the display.

Turning off the information in the display

Each time you press DISPLAY MODE on the remote while

playing a disc, the display turns off and on alternately.

Even when the display is turned off, the display turns on

if you pause or stop play. When you resume play, the

display turns off again.

Before you start playing, when you press DISPLAY

MODE to turn off the display, “DISPLAY OFF” appears,

and when you press the button to turn on the display,

“DISPLAY ON” appears.

DISCSALL

1 -43.32

SACD

CD1

DISC MIN SEC

12345

678910

12345

DISCSALL

1 1 -1.56

SACD

CD1

DISC TRACK MIN SEC

12345

678910

12345

DISCSALL

111 1.57

SACD

CD1

DISC TRACK INDEX MIN SEC

12345

678910

12345

Playing track number and elapsed playing time of

the current track (default display)

Press TIME/TEXT

Playing track number and remaining time of

the current track

Total remaining time on the disc

Press TIME/TEXT

Press

TIME/

TEXT

Total number of tracks

The information also appears when you press the

A OPEN/CLOSE button to close the disc tray.

The tracks numbered over 16 cannot be displayed in

the music calendar.

Notes on the disc number indications

• The red circle around a disc number indicates the disc is

ready to be played.

• When all the tracks on a disc have been played, the semi-

circle around the disc number disappears.

• When a disc compartment is recognized as empty, the semi-

circled disc number disappears.

Playing Discs

Displaying the information of a TEXT disc

TEXT discs contain information, such as the disc name or

artist name, as well as the audio signals. This player can

display the disc name, artist name, and current track

name as TEXT information.

When the player detects a TEXT disc, “TEXT” appears in

the display.

Displaying the information of a TEXT disc

in stop mode

Press TIME/TEXT.

Each time you press the button, the disc name or artist

name appears in the display. When you select the artist

name, “ART.” appears in the display.

• Before you start playing

Display information of a TEXT disc while

playing a disc

The current track name appears. If the disc name has

more than 15 characters, the first 14 characters will remain

after the name scrolls by in the display.

• While playing a disc

Notes

• The display may not show all the characters, depending on the

disc.

• This player can display only the disc name, artist name, and

track names from TEXT discs. Other information cannot be

displayed.

DISCSALL

SONY BAND

ART

CD1

TEXT

12345

678910

12345

DISCSALL

SONYHITS

CD1

TEXT

12345

678910

12345

DISCSALL

1 10 45.28

CD1

TEXT

DISC TRACK INDEX MIN SEC

12345

678910

12345

Disc title

Artist name

Total number of tracks and total playing time

Press TIME/TEXT

DISCSALL

HITECHBLUES

CD1

TEXT

TRACK

12345

678910

12345

DISCSALL

1 1 -1.57

CD1

TEXT

DISC TRACK INDEX MIN SEC

12345

678910

12345

DISCSALL

1 -43.32

CD1

TEXT

DISC MIN SEC

12345

678910

12345

DISCSALL

111 1.56

CD1

TEXT

DISC TRACK INDEX MIN SEC

12345

678910

12345

Remaining time on the current track

Remaining time on the disc

Playing time of the current track

Track title

Press TIME/TEXT

Press

TIME/

TEXT

Press TIME/TEXT

Using the Display

Press

TIME/

TEXT

Playing Discs

Locating a Specific Disc

You can locate any disc before or while playing a disc.

Number

buttons

>10

Replacing Discs While

Playing a Disc

You can open the disc tray while playing a disc so that

you can check what discs are to be played next and

replace discs without interrupting play of the current disc.

1 Press EX-CHANGE.

The disc tray opens and two disc compartments

appear. Even if the player is playing a disc, it doesn’t

stop playing.

2 Replace discs in the compartments with new ones.

The player plays the disc on the left side compartment

after the current disc, and then the one on the right

side compartment.

3 Press DISC SKIP.

The disc tray turns and other two disc compartments

appear.

4 Replace discs in the compartments with new ones.

5 Press EX-CHANGE.

The disc tray closes.

Note

Do not push the disc tray to close it in Step 5, as you may damage

the player.

While the disc tray is open by pressing the EX-CHANGE button

• If the play of the current disc ends, the player stops playing. If

the disc is played in 1 DISC Repeat Play mode (see page 17),

the current disc starts playing again.

• In ALL DISCS Shuffle Play mode (see page 18), tracks are

reshuffled on the current disc.

• In Program Play mode (see page 19), only the tracks on the

current disc are played.

EX-CHANGE

DISC SKIP

To locate

The next disc

The next or succeeding

discs

The current or preceding

discs

A specific disc directly

Press

DISC SKIP while playing a disc

DISC SKIP + repeatedly until you

find the disc

DISC SKIP – repeatedly until you

find the disc

DISC 1–5.

When using the remote, follow the

procedure below.

1 Press DISC.

2 Press the number button of the

disc.

3 Press ENTER.

DISC SKIP

DISC 1–5

DISC SKIP +/–

DISC

Playing Discs

Locating a Specific Track

During stop or play mode, you can locate any track to be

played.

lAMSL

Number

buttons

./>

>10

To locate

The next or

succeeding tracks

The current or

preceding tracks

A specific track directly

You need to

Turn l AMS L clockwise until

you find the track. When using the

remote, press > repeatedly until

you find the track.

Turn l AMS L

counterclockwise until you find the

track. When using the remote, press

. repeatedly until you find the

track.

Turn l AMS L until you find

the track number you want. When

using the remote, press . or >

repeatedly until you find the track.

Locating a track directly by entering the

track number Z

Press the number button(s) to enter the track number.

To enter a track number over 11 Z

1 Press >10.

2 Enter the corresponding digits.

To enter 0, press 10/0 instead.

Examples:

• To play track number 30, press >10, then 3 and 10/0.

• To play track number 100, press >10 twice, then 1, and 10/0

twice.

Locating a Particular Point

in a Track Z

You can locate a particular point in a track during play or

play pause.

Locating a point while monitoring the

sound (Search)

Press and hold m/M during play.

You will hear intermittent playback as the disc goes

forward or reverses.

When you reach the desired point, release the button.

Locating a point by observing the time

indication (High-Speed Search)

Press m/M during play pause.

You will not hear the playback sound.

When “Over!!” appears in the display

The disc has reached its end. Press . or m to go back.

Note

Tracks that are only a few seconds long may be too short for

monitoring. In this case, the player may not search correctly.

Locating a point by setting the start time

(Time Search)

1. Turn l AMS L or press ./> to select the

desired track in stop mode.

2. Press m/M to set the time to start play while

looking at the display.

You can set the time from the beginning of the desired a

track when you press M at first, and set the time from

the end of the desired track backward’s when you press

m at first.

3. Press H.

Play will start at the time search.

./>

m/M

DISCSALL

1 5 2.57

SACD

DISC TRACK MIN SEC

12345

678910

12345

lAMSL

Playing Discs

Repeating the current track

(Repeat 1 Play)

While the track you want to repeat is being played,

press REPEAT repeatedly until “REPEAT 1” appears in

the display.

Repeat 1 Play starts.

To stop Repeat 1 Play

Press x.

To resume normal play

Press REPEAT repeatedly until “REPEAT” goes off.

Playing Tracks Repeatedly

You can play an entire disc or portions thereof repeatedly.

This function can be used with Shuffle Play to repeat all

the tracks in random order (page 18), or with Program

Play to repeat all the tracks in a program (page 19).

Note

If you turn off the player or disconnect the mains lead, the player

will store the last setting of repeat play (“REPEAT” or “REPEAT

1”) and recall it the next time you turn on the player.

Repeating all the tracks on the disc

(Repeat All Play)

Press REPEAT once, then press H.

“REPEAT” appears in the display and Repeat All Play

starts.

The repeat play changes depending on the play mode you

select.

When the play mode is The player repeats

ALL DISCS Continuous

Play (page 12)

1 DISC Continuous Play

(page 12)

ALL DISCS Shuffle Play

(page 18)

1 DISC Shuffle Play

(page 18)

Program Play

(page 19)

To stop Repeat All Play

Press x.

To resume normal play

Press REPEAT repeatedly until “REPEAT” goes off.

REPEAT

All the tracks on all discs

All the tracks on the current disc

All the tracks on all discs in random

orders

All the tracks on the current disc in

random orders

All the tracks in the program in

sequence

Playing Discs

Playing Tracks in Random

Order (Shuffle Play)

You can have the player “shuffle” tracks and play in a

random order. The player shuffles all the tracks on all

discs or on the disc you’ve specified.

Shuffle Play on all discs

You can play all tracks on all discs in a random order.

1 Press SHUFFLE repeatedly until “ALL DISCS”

appears in the display.

2 Press H to start ALL DISCS Shuffle Play.

“;” appears while the player is “shuffling” the tracks.

The player will stop after playing all the tracks once.

CONTINUE

SHUFFLE

./>

Shuffle Play on one disc

You can play all tracks on the specific disc in a random

order.

1 Press SHUFFLE repeatedly until “1 DISC” appears in

the display.

2 Press DISC 1–5 to start 1 DISC Shuffle Play on the

selected disc.

“;” appears while the player is “shuffling” the tracks.

The player will stop after playing all the tracks once.

To resume normal play

Press CONTINUE.

You can locate tracks during Shuffle Play

Turn lAMSL or press ./>.

The player does not go back to tracks which have already been

played.

You can start Shuffle Play while playing

Press SHUFFLE, and Shuffle Play starts from the current track.

DISC 1–5

lAMSL

CONTINUE

SHUFFLE

Playing Discs

Creating Your Own

Program (Program Play)

You can pick out the tracks that you like and specify the

playback order in a program containing up to 32 tracks.

1 Press PROGRAM in stop mode.

“PROGRAM” appears in the display.

2 Press DISC.

Cursor flashes in the display.

3 Press the number button of the disc.

The selected disc number appears in the display.

4 Press ENTER.

When you want to program the whole disc as one

step, skip Steps 5 to 6, and go to Step 7.

5 Press the number buttons to enter the track

number.

If you entered the wrong track number

Press CLEAR to erase the track number and reenter

the correct track number using the number buttons.

To select a track number over 11

Press >10 (page 16).

6 Press ENTER.

7 Repeat steps 2 to 6 to enter other tracks.

8 Press H.

Program Play starts.

CLEAR

CONTINUE

Number

buttons

>10

PROGRAM

CHECK

./>

To resume normal play

Press CONTINUE.

You can create your program while checking the disc labels

While the disc tray is open, follow Steps 1 to 8 with pressing the

DISC SKIP button to check the disc labels. If you close the disc

tray before Step 8, the total playing time appears in the display

after a while.

Note that, if the programmed track number isn’t found on the

disc, that step is automatically erased.

The program remains even after Program Play ends

Press H to play from the beginning of the program again.

The program remains even if you stop play.

The program remains until you erase it

If you replace discs, the programmed disc and track numbers

remain. So, the player plays only the existing disc and track

numbers. However, the disc and track numbers that aren’t found

in the player or on the disc are deleted from the program, and the

rest of the program is played in the programmed order.

Notes

• When tracks which are not numerically consecutive on the disc

are programmed consecutively (i.e. 1, 3, 5, etc.), the actual

playing time may become longer than the total playing time.

• If you turn off the player, disconnect the mains lead, or press

A OPEN/CLOSE the program will be erased.

Checking the contents of the program

Before you start playing or while the player is playing,

press CHECK.

Each time you press the button, the track numbers will

appear in the display in the programmed order.

When you press CHECK while the player is playing, the

track number appears from the next track numbers of the

current playing track number.

ENTER

DISC

Playing Discs

Do the following:

1 Press CHECK repeatedly until the track

number you want to erase appears.

2 Press CLEAR.

Press CLEAR.

Each time you press the button, the last

track of the program is erased.

Press DISC SKIP +/– and ./> to

select the track you want to add, then press

PROGRAM. When using the remote, press

the number button of the track to be added.

Hold down CLEAR until ”CLEAR“ appears

in the display.

Listening to a CD Using a

Filter (Digital Filter Function) Z

This player is equipped with a variable coefficient (V.C.*)

digital filter. By selecting one of five types of filters

(“STD,” “1,” “2,” “3,” and “4”), you can adjust the sound

to match your listening environment and the music

source.

*V.C. is a trademark of Variable Coefficient. For details,

see “What is a variable coefficient (V.C.) digital filter?”

Note

Digital filters are effective only when you play a conventional

CD. You cannot select the digital filter when you play a Super

Audio CD.

Press DIGITAL FILTER repeatedly until you locate

the filter you want.

If you press DIGITAL FILTER to change the type of filters

during play, the type of filter appears in the display and

the sound will be interrupted momentarily.

DIGITAL FILTER

Creating Your Own Program (Program Play)

Changing the contents of the program

You can change the contents of the program in stop mode.

Erase a track

Erase from the last

track in the program

Add a track to the

end of the program

Erase all tracks

La page charge ...

Sony SCD-C333ES Manuel utilisateur

Marque: Sony

Modèle: SCD-C333ES

Catégorie: Lecteur CD

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sony SCD-C333ES User manual

Sony SCD-C333ES Manuel utilisateur

Sony SCD-C333ES Manuel utilisateur

dans d''autres langues

Documents connexes