Samsung HT-J4100 Manuel utilisateur

5.1CH Blu-ray™

Home Entertainment System

User manual

HT-J4100

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at

www.samsung.com/register

HT-J4100_ZC-0206.indd 1HT-J4100_ZC-0206.indd 1 2015-02-06  7:02:392015-02-06  7:02:39

2 - English

Safety Information

•

The slots and openings in the cabinet and in the back

or bottom are provided for necessary ventilation. To

ensure reliable operation of this apparatus, and to

protect it from overheating, these slots and openings

must never be blocked or covered.

-

Do not place this apparatus in a confined space,

such as a bookcase, or built-in cabinet, unless proper

ventilation is provided.

-

Do not place this apparatus near or over a radiator or

heat register, or where it is exposed to direct sunlight.

-

Do not place vessels (vases etc.) containing water on

this apparatus. A water spill can cause a fire or electric

shock.

•

Do not expose this apparatus to rain or place it near water

(near a bathtub, washbowl, kitchen sink, or laundry tub,

in a wet basement, or near a swimming pool, etc.). If this

apparatus accidentally gets wet, unplug it and contact an

authorized dealer immediately.

•

This apparatus uses batteries. In your community, there

might be environmental regulations that require you to

dispose of these batteries properly. Please contact your

local authorities for disposal or recycling information.

•

Do not overload wall outlets, extension cords or adaptors

beyond their capacity, since this can result in fire or

electric shock.

•

Route power-supply cords so that they are not likely to be

walked on or pinched by items placed on or against them.

Pay particular attention to cords at the plug end, at wall

outlets, and the point where they exit from the apparatus.

•

To protect this apparatus from a lightning storm, or when

it is left unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the antenna

or cable system. This will prevent damage to the set due

to lightning and power line surges.

•

Before connecting the AC power cord to the DC adaptor

outlet, make sure the voltage designation of the DC

adaptor corresponds to the local electrical supply.

•

Never insert anything metallic into the open parts of this

apparatus. Doing so may create a danger of electric

shock.

•

To avoid electric shock, never touch the inside of this

apparatus. Only a qualified technician should open this

apparatus.

•

Make sure to plug the power cord in until it is firmly

seated. When unplugging the power cord from a wall

outlet, always pull on the power cord's plug. Never unplug

by pulling on the power cord. Do not touch the power

cord with wet hands.

•

If this apparatus does not operate normally - in particular,

if there are any unusual sounds or smells coming from it -

unplug it immediately and contact an authorized dealer or

service center.

•

Maintenance of Cabinet.

-

Before connecting other components to this product,

be sure to turn them off.

-

If you move your product suddenly from a cold place

to a warm place, condensation may occur on the

operating parts and lens and cause abnormal disc

playback. If this occurs, unplug the product, wait for

two hours, and then connect the plug to the power

outlet. Then, insert the disc, and try to play back again.

•

Be sure to pull the power plug out of the outlet if the

product is to remain unused or if you are leaving the

house for an extended period of time (especially when

children, elderly, or disabled people will be left alone in the

house).

-

Accumulated dust can cause an electric shock, an

electric leakage, or a fire by causing the power cord

to generate sparks and heat or the insulation to

deteriorate.

•

Contact an authorized service center for information if

you intend to install your product in a location with heavy

dust, high or low temperatures, high humidity, chemical

substances, or where it will operate 24 hours a day such

as in an airport, a train station, etc. Failing to do so may

lead to serious damage of your product.

•

Use only a properly grounded plug and wall outlet.

-

An improper ground may cause electric shock or

equipment damage. (Class l Equipment only.)

•

To turn this apparatus off completely, you must disconnect

it from the wall outlet. Consequently, the wall outlet and

power plug must be readily accessible at all times.

CAUTION

RISK OF ELECTRIC SHOCK. DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK). THERE ARE NO USER

SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO

QUALIFIED PERSONNEL.

This symbol indicates that high voltage is

present inside. It is dangerous to make

any kind of contact with any internal part

of this product.

This symbol indicates that important

literature concerning operation and

maintenance has been included with this

product.

HT-J4100_ZC-0206.indd 2HT-J4100_ZC-0206.indd 2 2015-02-06  7:02:512015-02-06  7:02:51

3 - English

Safety Information

•

Do not allow children to hang on the product.

•

Store the accessories (battery, etc.) in a location safely out

of the reach of children.

•

Do not install the product in an unstable location such

as a shaky self, a slanted floor, or a location exposed to

vibration.

•

Do not drop or strike the product. If the product is

damaged, disconnect the power cord and contact a

service center.

•

To clean this apparatus, unplug the power cord from

the wall outlet and wipe the product using a soft, dry

cloth. Do not use any chemicals such as wax, benzene,

alcohol, thinners, insecticide, air fresheners, lubricants, or

detergent. These chemicals can damage the appearance

of the product or erase the printing on the product.

•

Do not expose this apparatus to dripping or splashing.

Do not put objects filled with liquids, such as vases on the

apparatus.

•

Do not dispose of batteries in a fire.

•

Do not plug multiple electric devices into the same wall

socket. Overloading a socket can cause it to overheat,

resulting in a fire.

•

There is danger of an explosion if you replace the batteries

used in the remote with the wrong type of battery. Replace

only with the same or equivalent type.

WARNING :

•

TO PREVENT THE SPREAD OF FIRE,

KEEP CANDLES AND OTHER ITEMS

WITH OPEN FLAMES AWAY FROM THIS

PRODUCT AT ALL TIMES.

•

To reduce the risk of fire or electric shock, do not expose

this appliance to rain or moisture.

NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer’s

attention to Section 820~40 of the NEC which provides

guidelines for proper grounding and, in particular, specifies

that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as

practical.

CLASS 1 LASER PRODUCT

This product is classified as a CLASS 1 LASER product. Use

of controls, adjustments or performance of procedures other

than those specified herein may result in hazardous radiation

exposure.

Complies with 21CFR 1040.10 except for deviations

pursuant to Laser Notice No. 50, dated June 24, 2007.

DANGER :

•

VISIBLE AND INVISIBLE LASER RADIATION WHEN

OPEN. AVOID DIRECT EXPOSURE TO BEAM.

(FDA 21 CFR)

CAUTION :

•

CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION

WHEN OPEN. AVOID EXPOSURE TO THE BEAM (IEC

60825-1)

•

THIS PRODUCT UTILIZES A LASER. USE OF

CONTROLS OR ADJUSTMENTS OR PERFORMANCE

OF PROCEDURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS RADIATION

EXPOSURE. DO NOT OPEN THE COVER. DO NOT

REPAIR THE PRODUCT YOURSELF. REFER SERVICING

TO QUALIFIED PERSONNEL.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

PRODUCTO LÁSER CLASE 1

Important Safety Instructions

Read these operating instructions carefully before using the

unit. Follow all the safety instructions listed below. Keep

these operating instructions handy for future reference.

1.

Read these instructions.

2.

Keep these instructions.

3.

Heed all warnings.

4.

Follow all instructions.

5.

Do not use this apparatus near water.

6.

Clean only with a dry cloth.

7.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8.

Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including AV

receivers) that produce heat.

HT-J4100_ZC-0206.indd 3HT-J4100_ZC-0206.indd 3 2015-02-06  7:02:522015-02-06  7:02:52

4 - English

Safety Information

9.

Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10.

Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where it exits the apparatus.

11.

Only use attachments/accessories specified by the

manufacturer.

12.

Use only with the cart, stand,

tripod, bracket, or table specified

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination to

avoid injury from tip-over.

13.

Unplug this apparatus during lightning storms or when

unused for long periods of time.

14.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as when the power-supply

cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not

operate normally, or has been dropped.

HT-J4100_ZC-0206.indd 4HT-J4100_ZC-0206.indd 4 2015-02-06  7:02:522015-02-06  7:02:52

5 - English

Contents

GETTING STARTED

6 Accessories

6 Speaker Components

6 Front Panel

7 Rear Panel

8 Remote Control

CONNECTIONS

9 Connecting the Speakers

11 Connecting to a TV and External Devices

SETTINGS

12 The Initial Settings Procedure

12 The Home Screen at a Glance

13 Accessing the Settings Screen

13 Settings Menu Functions

16 Radio Setup

17 Upgrading Software

PLAYING CONTENT

18 Switching the Source Device

18 Playing Commercial Discs

18 Playing a Disc with User Recorded Content

19 Playing Files on a USB Device

20 Controlling Video Playback

22 Playing a Pre-Recorded Commercial Audio Disc

22 Controlling Music Playback

24 Playing Photo Content

24 Using the Special Effects Remote Control Buttons

APPENDIX

26 Additional Information

27 Disk and Format Compatibility

32 Troubleshooting

35 Specifications

36 Licenses



Figures and illustrations in this User Manual

are provided for reference only and may differ

from actual product appearance.

HT-J4100_ZC-0206.indd 5HT-J4100_ZC-0206.indd 5 2015-02-06  7:02:532015-02-06  7:02:53

6 - English

Getting Started

Check the box for the accessories and speaker components listed or shown below.

Accessories

•

Remote Control

•

Batteries (AAA size)

•

User Manual

Power Cable FM Antenna

Speaker Components

Front x 2 Surround x 2 Center Subwoofer

Front Panel

DISPLAY ICONS

FUNCTION STOP PLAY/PAUSE

OPEN/

CLOSE

VOLUME

CONTROL

POWER

5V 0.5A

USBREMOTE CONTROL SENSOR

DISPLAY

DISC TRAY

✎

When the product is on, do not let children touch the product's surface. It will be hot.

✎

To upgrade the product's software through the USB jack, you must use a USB flash drive.

HT-J4100_ZC-0206.indd 6HT-J4100_ZC-0206.indd 6 2015-02-06  7:02:532015-02-06  7:02:53

7 - English

Getting Started

✎

When the product displays a Blu-ray Disc menu, you cannot start the movie by pressing the /

6

button

on the product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and

then press the

E

button.

✎

If you are playing content from a USB device on your TV through the home theater, you cannot select the

BD/DVD mode with the

FUNCTION button. To select the BD/DVD mode, stop the content you are playing

on the TV, and then select the BD/DVD mode.

Rear Panel

SURROUND

COOLING FAN

* FM ANTENNA

AUX IN

HDMI OUT

SPEAKER OUTPUT

CONNECTORS

POWER CORD EXTERNAL DIGITAL

AUDIO IN (OPTICAL)

* Connecting the FM Antenna

1.

Connect the supplied FM antenna to the FM ANT Jack.

2.

Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or

other rigid surface.

✎

Maintain a minimum of 4 inches of clear space on all sides of the home theater to ensure adequate

ventilation.

Do not obstruct the cooling fan or ventilation holes.

✎

This product does not receive AM broadcasts.

HT-J4100_ZC-0206.indd 7HT-J4100_ZC-0206.indd 7 2015-02-06  7:02:562015-02-06  7:02:56

8 - English

Getting Started

Remote Control

Tour of the Remote Control

Turn the product on and off.

Adjust the volume.

Press numeric buttons to operate

options.

Press to skip backwards or forwards.

Selects the disc subtitle language.

Press to move to the Home screen.

Select on-screen menu items and

change menu values.

Return to the previous menu.

These buttons are used both for

menus on the product and also

several Blu-ray Disc functions.

Press to view the disc menu.

Press to use the Tools menu.

Press to play a disc or files.

Press to direct the audio signal to the

home theater speakers or TV speaker.

(See page 24)

Select the desired DSP/EQ audio

mode.

Press to record FM radio broadcasts.

Press to stop a disc or files.

Cut off the sound temporarily.

Press to search backwards or

forwards.

Press to pause playing.

Allows you to repeat a title,

chapter, track or disc.

Use to enter the Popup menu/

Title menu.

Select MONO or STEREO for radio

broadcasts.

Search for active FM stations and

to change channels.

Use to display the playback

information when playing

a Blu-ray/DVD disc or files.

To open and close the disc tray.

Press to exit the menu.

Press to select Home Theater's

mode. (BD/DVD, D. IN, AUX, etc.).

Use to set a preset radio frequency.

TOOLS

RETURN

EXIT

INFO

SUBTITLE HOME REPEAT

1

2

3

7

89

DISC MENU TITLE MENU

0

POPUP

4

56

MUTE

MO/ST

TUNER

MEMORY

ABCD

TUNING

DOWN

UP

VOLUME

-

+

DSP/EQTV SOUND

FUNCTION

Installing batteries in the Remote Control

✎

Make sure to match the "+" and "–" ends of the batteries with

the diagram inside the compartment.

✎

Assuming typical usage, the batteries last for about one year.

✎

The remote control can be used up to approximately

23 feet from the product in a straight line.

Battery size: AAA

HT-J4100_ZC-0206.indd 8HT-J4100_ZC-0206.indd 8 2015-02-06  7:02:572015-02-06  7:02:57

9 - English

Connections

This section describes various methods of connecting the product to other external components.

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting the Speakers

Surround (L)

Surround (R)

Product

Center

Subwoofer

Front (L)

Front (R)

Position of the product

Place it on a stand or cabinet shelf,

or under the TV stand.

Selecting the Listening Position

The listening position should be

located about 2.5 to 3 times the

TV's screen size away from the TV.

For example, if you have a 46 inch

screen, locate the listening position

115 to 138 inches (9.6 to 11.5 feet)

from the screen.

Front Speakers

Place these speakers in front of your listening position, facing inwards (about 45°)

toward you. Place the front speakers so that their tweeters will be at the same height

as your ear. Align the front face of the front speakers with the front face of the center

speaker or place them slightly in front of the center speakers.

Center Speaker

It is best to install the center speaker at the same height as the front speakers. You

can also install it directly over or under the TV.

Surround Speakers

Place these speakers to the side of your listening position. If there isn't enough

room, place these speakers so they face each other. Position them about 2 to

3 feet above your ear, facing slightly downward.

* Unlike the front and center speakers, the surround speakers are used mainly for

sound effects. Sound will not come from them all the time.

Subwoofer

The position of the subwoofer is not so critical. Place it anywhere you like.

* The appearance of your speakers may differ from the illustrations in this manual.

* Each speaker has a colored label on its back or underside. Each cable has a single colored band near

its end. Match the band on each cable to the speaker label by color, and then connect the cable to the

speaker. See page 10 for exact instructions.

Connections

HT-J4100_ZC-0206.indd 9HT-J4100_ZC-0206.indd 9 2015-02-06  7:02:592015-02-06  7:02:59

10 - English

Connections

Speaker Cable Connections

SURROUND

Front Speaker (R)

Subwoofer

Center Speaker

Surround

Speaker (L)

Front Speaker (L)

Surround

Speaker (R)

✎

If you place a speaker near your TV set, the screen color may be distorted because of the magnetic field.

| CAUTION |



If you want to install the speakers on the wall, fasten screws or nails (not provided) firmly to the wall wherever

you want to hang a speaker, and then, using the hole in the rear of each speaker, carefully hang each

speaker on a screw or nail.



Do not let children play with or near the speakers. They could get hurt if a speaker falls.



When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.



Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien

substances into the duct (hole) of the subwoofer speaker.



Do not hang the subwoofer on the wall

by

the duct (hole).

HT-J4100_ZC-0206.indd 10HT-J4100_ZC-0206.indd 10 2015-02-06  7:03:002015-02-06  7:03:00

11 - English

Connections

Connecting to a TV and External Devices

OPTICAL OUT

AUDIO OUT

HDMI IN (ARC)

SURROUND

Method 1 Method 2

R

Red

W

White

External Devices

Connecting to a TV

Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack on

your TV. If the TV supports ARC, you can hear the audio from your TV through the home theater with only this cable

connected. See page 14 in this manual and the section on ARC in your TV's user's manual for details.

Connecting to External Devices

Two methods of connecting external devices to your home theater are explained below.

Method 1 AUX IN : Connecting an External Analog Component

Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out jack on the

external analog component.



Select the AUX mode.

•

Be sure to match the colors on the cable plugs to the colors on the input and output jacks.

Method 2 OPTICAL : Connecting an External Digital Audio Component

Use to connect the digital audio output of digital signal components such as Cable Boxes and Satellite Receivers (Set-

Top-Boxes) to the home theater. Using a digital optical cable (not supplied), connect the Optical Digital Audio In jack

on the product to the Digital Optical Out jack of the external digital device using a digital optical cable.



Select the

D. IN mode.

✎

To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.

✎

This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.

✎

This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.

Selecting an External Device to Use

To select an external device after you have connected it, press the FUNCTION button. Each time you press the

button, the mode changes in this order : BD/DVD



D. IN



AUX



FM

HT-J4100_ZC-0206.indd 11HT-J4100_ZC-0206.indd 11 2015-02-06  7:03:002015-02-06  7:03:00

12 - English

Settings

The Initial Settings Procedure

•

The Home menu will not appear if you do not

configure the initial settings.

•

The OSD (On Screen Display) may change in this

product after you upgrade the software version.

•

The access steps may differ depending on the

menu you selected.

1.

Turn on your TV after connecting the product, and

then turn on the product. When you turn on the

product for the first time, the product automatically

displays the Setup Language screen.

2.

Press the ▲▼ buttons to select the desired

language, and then press the

E

button.

3.

The TV Aspect Ratio screen appears. Press the

▲▼ buttons to select a TV aspect ratio, and then

press the

E

button.

You have four choices:

16:9 Original - For widescreen TVs. Displays

widescreen pictures in their original 16:9 format

and 4:3 pictures (the old, standard format) in 4:3

pillar box format with black bars on the left and

right.

16:9 Full - For widescreen TVs. Displays

widescreen pictures in their original 16:9 format

and expands 4:3 pictures to fill the 16:9 screen.

4:3 Letter Box - For older, standard screen, analog

TVs. Displays 4:3 pictures in full screen and 16:9

pictures in letter box format that retains the 16:9

aspect ratio but puts black bars above and below

the picture.

4:3 Pan-Scan - For older, standard screen, analog

TVs. Displays 4:3 pictures in full screen and 16:9

pictures in Pan-Scan format that fills the screen,

but cuts off the left and right sides of the picture

and enlarges the middle vertically.

4.

The "Initial settings completed." screen appears,

and then the Home screen appears.

✎

If you want to display the Setup screen again

and make changes, select the Reset option. (See

page 15)

✎

If you use an HDMI cable to connect the product

to an Anynet+ (HDMI-CEC)-compliant Samsung

TV and 1.) You have set the Anynet+ (HDMI-CEC)

feature to On in both the TV and the product and

2.) You have set the TV to a language supported

by the product, the product will select that

language as the preferred language automatically.

The Home Screen at a Glance

PLAY DISC

Change

Device

Function

No Disc

Settings

PHOTOS VIDEOS MUSIC

1

345

2

1

PLAY DISC

The disc currently in the tray is displayed.

Press

E

to start playing the disc.

2

PHOTOS/VIDEOS/MUSIC

Play photos, videos, or music content from a

Disc or a USB device.

3

Change Device

Displays a list of external devices connected to the

main unit. Switch to the desired device.

4

Function

Use for switching to an external device or to the radio.

You can use the remote control’s FUNCTION button

and the main unit’s button for mode switching.

5

Settings

Set various functions to suit your personal

preferences.

HT-J4100_ZC-0206.indd 12HT-J4100_ZC-0206.indd 12 2015-02-06  7:03:022015-02-06  7:03:02

13 - English

Settings

Accessing the Settings Screen

1.

Select Settings on the Home screen, and then

press

E

. The Settings screen appears.

Settings

Picture

Sound

System

Language

Security

Support

TV Aspect Ratio : 16:9 Original

BD Wise : Off

Resolution : Auto

Movie Frame (24Fs) : Off

HDMI Color Format : Auto

HDMI Deep Color : Off

Progressive Mode : Auto

2.

To access the menus, sub-menus, and options

on the Settings screen, please refer to the remote

control illustration. (See below)

✎

If you leave the product in the stop mode for more

than 5 minutes without using it, a screen saver

appears on your TV. If the product is left in the

screen saver mode for more than 20 minutes, the

power automatically turns off.

Buttons on the Remote Control Used for

the Settings Menu

TOOLS

RETURN

EXIT

INFO

SUBTITLE HOME REPEAT

TUNER

24

3

1

HOME Button : Press to move to the Home

screen.

2

RETURN Button : Press to return to the

previous menu.

3

E

(

ENTER) / DIRECTION Button :

•

Press ▲▼◄► to move the cursor or select

an item.

•

Press the

E

button to activate the currently

selected item or confirm a setting.

4

EXIT Button : Press to exit the current menu.

Detailed Function Information

Each Settings function, menu item, and individual option

is explained in detail on-screen. To view an explanation,

use the ▲▼◄► buttons to select the function, menu

item, or option. The explanation will usually appear on

the bottom of the screen.

A short description of each Settings function starts

on this page. Additional information on some of the

functions is also in the Appendix of this manual.

Settings Menu Functions

Picture

TV Aspect Ratio

Lets you adjust the output of the product to the

screen size of your TV. (See page 26)

BD Wise

BD Wise is Samsung’s latest inter-connectivity

feature. When you connect a Samsung product and

a Samsung TV with BD Wise to each other via HDMI,

and BD Wise is on in both the product and TV, the

product outputs video at the video resolution and

frame rate of the Blu-ray/DVD Disc.

Resolution

Lets you set the output resolution of the HDMI video

signal to BD Wise, Auto, 1080p, 1080i, 720p, 480p.

The number indicates the number of lines of video per

frame. The i and p indicate interlaced and progressive

scan, respectively. The more lines, the higher quality.

Movie Frame (24Fs)

Setting the Movie Frame (24Fs) feature to Auto lets

the product adjust its HDMI output to 24 frames per

second automatically for improved picture quality if

attached to a 24Fs compatible TV.

•

You can enjoy the Movie Frame (24Fs) feature

only on a TV supporting this frame rate.

•

Movie Frame is only available when the product is

in the HDMI 1080p output resolution modes.

HT-J4100_ZC-0206.indd 13HT-J4100_ZC-0206.indd 13 2015-02-06  7:03:032015-02-06  7:03:03

14 - English

Settings

HDMI Color Format

Lets you set the color space format for the HDMI

output to match the capabilities of the connected

device (TV, monitor, etc).

HDMI Deep Color

Lets you set the product to output video from the

HDMI OUT jack with Deep Color. Deep Color provides

more accurate color reproduction with greater color

depth.

Progressive Mode

Lets you improve picture quality when viewing DVDs.

Sound

Speaker Settings

Lets you adjust the following speaker settings and

turn the speaker test on and off so you can test the

speakers.



Level

: Lets you adjust the relative loudness of

each speaker from 6dB to -6dB. For example, if

you like deep bass, you can increase the loudness

of the subwoofer by 6dB.



Distance

: Lets you adjust the relative distance

of each speaker from the listening position up to

30 feet. The farther the distance, the louder the

speaker will be.



Speaker Test

:

Lets you run the Speaker Test

function so you can test your adjustments. Setting

Speaker Test to On turns the Speaker Test on.

Setting it to Off turns it off.

Speaker Selection

Lets you select which speakers you want active,

either the TV's speakers or the home theater's

speakers.

Equalizer Mode

Set Equalizer Mode on to use the equalizer.

Equalizer Settings

Lets you set the equalizer.

✎

Equalizer Settings only appears when

Equalizer Mode is On.

Audio Return Channel

Lets you direct the sound from the TV to the Home

Theater speakers. Requires an HDMI connection and

an Audio Return Channel (ARC) compatible TV.

•

If Audio Return Channel is set to on and you are

using an HDMI cable to connect the product to the

TV, digital optical input will not work.

•

If Audio Return Channel is set to Auto and you

are using an HDMI cable to connect the product

to the TV, ARC or digital optical input is selected

automatically.

Digital Output

Lets you set the Digital Output to match the

capabilities of the AV receiver you’ve connected to

the product. For more details, please refer to the

digital output selection table. (See page 31)

Dynamic Range Control

Lets you apply dynamic range control to Dolby Digital,

Dolby Digital Plus, and Dolby TrueHD audio.



Auto:

Automatically controls the dynamic range of

Dolby TrueHD audio, based on information in the

Dolby TrueHD soundtrack. Also turns dynamic range

control off for Dolby Digital and Dolby Digital Plus.



Off: Leaves the dynamic range uncompressed,

letting you hear the original sound.



On: Turns dynamic range control on for all three

Dolby formats. Quieter sounds are made louder

and the volume of loud sounds is reduced.

Downmixing Mode

Lets you select the multi-channel downmix method

that is compatible with your stereo system. You can

choose to have the product downmix to Normal

Stereo or to Surround Compatible.

Audio Sync

When the product is attached to a digital TV, lets you

adjust the audio delay so that the audio syncs with

the video. You can set the delay between 0 and 300

milliseconds.

HT-J4100_ZC-0206.indd 14HT-J4100_ZC-0206.indd 14 2015-02-06  7:03:042015-02-06  7:03:04

15 - English

Settings

System

Setup

Lets you re-run the Setup procedure. (See page 12)

Quick Start

You can turn on the power quickly by decreasing the

boot time.

✎

If this function is set to On, Standby power

consumption will be increased. (About 12W ~

20W)

Anynet+ (HDMI-CEC)

Anynet+ is a convenient function that offers linked

operations with other Samsung products that have

the Anynet+ feature and lets you control those

products with one Samsung TV remote. To operate

this function, you must connect this product to an

Anynet+ Samsung TV using an HDMI cable.

BD Data Management

Enables you to manage the downloaded contents

you accessed through a Blu-ray disc and stored on a

flash drive.

You can check the device's information including the

available storage size, delete the BD data, or change

the Flash memory device.

Language

Lets you select the language you prefer for the On-

Screen Menu, Disc Menu, etc.

•

The selected language will only appear if it is

supported on the disc.

Security

The default PIN is 0000. Enter the default PIN to

access the security function if you haven't created

your own PIN.

BD Parental Rating

Prevents playback of Blu-ray Discs with a rating equal

to or above a specific age rating unless you enter the

PIN.

DVD Parental Rating

Prevents playback of DVDs with a rating above a

specific numerical rating unless you enter the PIN.

Change PIN

Changes the 4-digit PIN used to access security

functions.

Support

Software Upgrade

For more information about this function, see page

17.

Contact Samsung

Provides contact information for assistance with your

product.

Reset

Reverts all settings to their defaults. Requires that you

enter your security PIN. The default security PIN is

0000.

HT-J4100_ZC-0206.indd 15HT-J4100_ZC-0206.indd 15 2015-02-06  7:03:042015-02-06  7:03:04

16 - English

Settings

Radio Setup

•

To listen to the radio, you must connect the

supplied FM antenna.

Operating the Radio with the Remote Control

1.

Press the FUNCTION button to select FM.

2.

Tune to the desired station.

•

Preset Tuning 1 : Press the

5

button to select

PRESET, and then press the TUNING UP,

DOWN button to select a preset station.

Before you can tune to preset stations, you

must add preset stations to the product's

memory.

•

Manual Tuning : Press the

5

button to select

MANUAL, and then press the TUNING UP,

DOWN button to tune in to a lower or higher

frequency.

•

Automatic Tuning : Press the

5

button to

select MANUAL, and then press and hold the

TUNING UP, DOWN button for a few seconds

to automatically search the band.

Selecting Mono or Stereo

Press the MO/ST button.

•

Each time you press the button, the sound switches

between STEREO and MONO.

•

In a poor reception area, select MONO for a clear,

interference-free broadcast.

Presetting Stations

Example : Presetting FM 89.10 into memory.

1.

Press the FUNCTION button to select FM.

2.

Press the TUNING UP, DOWN button to scroll the

FM frequencies, and then select <89.10>.

3.

Press the TUNER MEMORY button (the yellow C

button at the bottom of the remote).

4.

Press the TUNER MEMORY button again within

about 5 seconds. The station is stored in memory.

✎

If you press the

TUNER MEMORY

button

repeatedly without changing the station, the

inputted station may be overwritten.

5.

To preset another station, repeat steps 2 to 4.

•

To tune in to a preset station, press the TUNING

UP, DOWN button.

✎

To delete all Preset FM stations at once, press the

TITLE MENU button for about 5 seconds in FM

Manual mode until DEFAULT PRESET appears

on the display.

Recording FM Radio

You can record your favorite radio broadcast on a USB

storage device.

1.

Insert a USB device into the USB jack on the front

of the product.

2.

Press the FUNCTION button to select FM, and

then press the TUNING UP, DOWN button to

select the station you want to record.

3.

Press the RED (A) button to start recording. The

recording process begins.

•

The recorded time is displayed on the left and

the recording time still available, based on the

amount of free space in the USB storage device,

is displayed on the right.

4.

Press the EXIT button to finish your recording. The

recording is stopped and saved as an .mp3 file at

the same time. To play the recorded file, refer to

"Playing Files on a USB Device".

✎

The recorded file is saved in the Tuner folder which

is created automatically.

✎

Only the (OPEN/CLOSE), (POWER), EXIT,

MUTE, and VOLUME +/-, buttons are operable

while FM radio is being recorded.

✎

If you don't press any buttons while recording, the

screen saver will be enabled.

✎

Sound effects, such as DSP, EQ, etc., are not

recorded during FM radio recording.

✎

The radio is recorded at a set, default volume

even if you change the volume or press the

MUTE

button during the recording process.

✎

If you remove the USB device or Power Cable

during the recording process, the portion of the

file which has already been recorded may not play

back.

HT-J4100_ZC-0206.indd 16HT-J4100_ZC-0206.indd 16 2015-02-06  7:03:052015-02-06  7:03:05

17 - English

Settings

✎

Recording will not start if the remaining free space

in the USB storage device is less than 2MB.

✎

If the USB device is removed or has insufficient

space (under 2MB), the appropriate message is

displayed and the recording stops.

Upgrading Software

The Software Upgrade menu allows you to upgrade

the product’s software for performance improvements or

additional services.

•

Never turn the product off or back on manually

during the update process.

•

The update is complete when the product turns off

after restarting. Press the POWER button to turn

on the updated product for your use.

1.

Visit www.samsung.com.

2.

Click OWNERS & SUPPORT on the top right of

the page, and then select Manuals & Downloads

from the drop down that appears.

3.

On the next screen, enter the product's model

number into the search field. As you enter the

model number, a drop down will display products

that match the model number.

4.

Left click your product's model number in the drop

down list.

5.

On the page that appears, select Downloads.

6.

Find the Upgrade File (USB type) in the Description

column. Click the ZIP icon in the Download File

column on the right.

7.

Click Send in the pop-up that appears. The file

downloads to your PC.

8.

Unzip the zip archive to your computer. You should

have a single folder with the same name as the zip

file.

9.

Copy the folder to a USB flash drive.

10.

Make sure no disc is inserted in the product, and

then insert the USB flash drive into the USB port of

the product.

11.

In the product’s menu, go to Settings > Support >

Software Upgrade.

12.

Select By USB.

13.

The home theater searches for the software on the

USB drive. When it finds the software, the Update

Request pop-up appears.

14.

Select OK. The home theater turns off, turns on,

and then begins the upgrade. When the upgrade is

done, the home theater turns off.

15.

Press the POWER button to turn on the home

theater.

✎

There should be no disc in the product when you

upgrade the software using the USB Host jack.

✎

When the software upgrade is done, check the

software details in the Software Upgrade menu.

HT-J4100_ZC-0206.indd 17HT-J4100_ZC-0206.indd 17 2015-02-06  7:03:052015-02-06  7:03:05

18 - English

Playing Content

Your home theater can play content located on

Blu-ray/DVD/CD discs and USB devices.

Switching the Source Device

If two or more external devices are connected to

the main unit, you can use any of the three methods

described below to change the source device.

Method 1

From the Home screen, use the ▲▼◄► buttons to

move to Change Device, and then press

E

.

The Change Device popup window will appear. Use the

▲▼ buttons to move to the desired device, and then

press

E

.

Method 2

If you move to PHOTOS, VIDEOS, MUSIC or other file-

based contents, a list of folders and files will appear.

Press the RED (A) button to display the Change Device

popup window, use the ▲▼ buttons to move to the

desired device, and then press

E

.

Method 3

When a device is connected for the first time, a popup

window appears. In the popup, you can change the

source device by using the ◄► buttons, and then

pressing

E

.

Playing Commercial Discs

1.

Press the



button to open the disc tray.

2.

Place a disc gently into the disc tray with the disc’s

label facing up.

3.

Press the



button to close the disc tray.

Playback starts automatically.

4.

If playback does not start automatically, press the

6

button on the remote.

Disc Storage & Management

•

Holding Discs

- Fingerprints or scratches on

a disc may reduce sound and

picture quality or cause skipping.

- Avoid touching the surface of a disc where data has

been recorded.

- Hold the disc by the edges so that fingerprints will

not get on the surface.

- Do not stick paper or tape on the disc.

•

Cleaning Discs

- If you get fingerprints or dirt on a disc,

clean it with a mild detergent diluted in

water and wipe with a soft cloth.

- When cleaning, wipe gently from the

inside to the outside of the disc.

- Disc Storage



Do not keep in direct sunlight.



Keep in a cool ventilated area.



Keep in a clean protective jacket and store

vertically.

Playing a Disc with User Recorded

Content

You can play multimedia files you have recorded on Blu-

ray, DVD, or CD discs.

1.

Place a user recorded disc into the disc tray with

the disc’s label facing up, and then close the tray.

2.

Use the ◄► buttons to select the type of content

you want to view or play - PHOTOS, VIDEOS, or

MUSIC - and then press the

E

button.

OR

2

-1

. Select PLAY DISC from the Home screen. The

PLAY DISC screen appears. Use the ▲▼ buttons

to select the desired content type, Photos, Videos,

or Music.

3.

A screen appears listing the contents of the disc.

Depending on how the contents are arranged, you

will see either folders, individual files, or both.

4.

If necessary, use the ▲▼◄► buttons to select a

folder, and then press the

E

button.

HT-J4100_ZC-0206.indd 18HT-J4100_ZC-0206.indd 18 2015-02-06  7:03:062015-02-06  7:03:06

19 - English

Playing Content

5.

Use the ▲▼◄► buttons to select a file to view or

play, and then press the

E

button.

6.

Press the RETURN button one or more times to

exit a current screen, exit a folder, or to return to

the Home screen.

Press the

EXIT button to return directly to the

Home Screen.

7.

Go to pages 20~24 for instructions that

explain how to control playback of videos, music,

and pictures on a disc.

Playing Files on a USB Device

There are two methods you can use to play or view

multimedia files located on a USB device through your

product.

Method 1 : If you connect a USB device while

the product is turned on

1.

The "New device connected." pop-up appears.

PLAY DISC

Change

Device

Function

No Disc

Settings

PHOTOS VIDEOS MUSICPLAY DI

SC

C

han

g

e

D

e

vi

ce

Fu

n

c

ti

o

n

N

o

Di

s

c

Settin

gs

PH

O

T

OS

V

IDE

OS

MUS

I

C

New device connected.

STORAGE DEVICE

Photos

Videos

Music

> Move " Enter ' Return

✎

If the pop-up does not appear, go to Method 2.

2.

Use the ▲▼ buttons to select Photos, Videos, or

Music and then press the

E

button. Depending

on how the contents are arranged, you will see

either folders, individual files, or both.

3.

If necessary, use the ▲▼◄► buttons to select a

folder, and then press the

E

button.

4.

Select a file to view or play, and then press the

E

button.

5.

Press the RETURN button to exit a folder or the

EXIT button to return to the Home screen.

6.

Go to pages 20~24 for instructions that

explain how to control playback of videos, music,

and pictures on a USB device.

Method 2 : If the product is turned on after

you connect a USB device

1.

Turn the product on.

2.

Press Change Device and select a USB device.

3.

Use the ◄► buttons to select PHOTOS, VIDEOS,

or MUSIC on the Home screen, and then press the

E

button.

4.

If necessary, use the ▲▼◄► buttons to select a

folder, and then press the

E

button.

5.

Select a file to view or play, and then press the

E

button.

6.

Press the RETURN button to exit a folder or the

EXIT button to return to the Home screen.

7.

Go to pages 20~24 for instructions that

explain how to control playback of videos, music,

and pictures on a USB device.

✎

If you insert a disc while playing a USB device, the

device mode changes to "Disc" automatically.

HT-J4100_ZC-0206.indd 19HT-J4100_ZC-0206.indd 19 2015-02-06  7:03:072015-02-06  7:03:07

20 - English

Playing Content

Controlling Video Playback

You can control the playback of video content located

on a Blu-ray/DVD disc or USB device. Depending on the

disc or contents, some of the functions described in this

manual may not be available.

Buttons on the Remote Control used for

Video Playback

SUBTITLE HOME REPEAT

DISC MENU TITLE MENU

0

POPUP

1

2

3

1

Playback related buttons

The product does not play sound in Search, Slow, or

Step mode.

•

To return to normal speed playback, press the

6

button.

6

Starts playback.

5

Stops playback.

7

Pauses playback.

Fast Motion

Play

During playback, press the

3

or



button.

Each time you press the

3

or



button, the playback speed will

change.

Slow

Motion Play

In pause mode, press the



button.

Each time you press the



button,

the playback speed will change.

Step Motion

Play

In pause mode, press the

7

button.

Each time you press the

7

button, a

new frame appears.

Skip Motion

Play

During playback, press the

1

or

2

button.

Each time you press the

1

or

2

button, the disc moves to the

previous or next chapter or file.

2

Using the disc menu, title menu, popup

menu, and title list

DISC MENU

During playback, press this button to display the Disc

menu.

TITLE MENU

During playback, press this button to display the Title

menu.

•

If your disc has a playlist, press the GREEN (B)

button to go to the playlist.

POPUP MENU

During playback, press this button to display the

Popup menu.

3

Repeat Playback

1.

During playback, press the REPEAT button on

the remote control.

2.

Press the ▲▼ buttons to select Off, Title,

Chapter, All or Repeat A-B, and then press the

E

button.



Repeat A-B

1.

Press the

E

button at the point where you

want repeat play to start (A).

2.

Press the

E

button at the point where you

want repeat play to stop (B).

3.

To return to normal play, press the REPEAT

button again.

4.

Press the

E

button.

✎

Depending on the disc, the screen may not

display all repeat options.

✎

The screen may not display Chapter or Title

immediately. Continue to press the ▲▼ buttons

until your choice is inside the applicable field.

✎

To return to normal play, press the REPEAT

button again, press the ▲▼ buttons to select

Off, and then press the

E

button.

✎

The screen may not display Repeat A-B

immediately. Continue to press the ▲▼ buttons

until Repeat A-B is inside the applicable field.

✎

You must set point (B) at least 5 seconds of

playing time after point (A).

HT-J4100_ZC-0206.indd 20HT-J4100_ZC-0206.indd 20 2015-02-06  7:03:082015-02-06  7:03:08

La page charge ...

Samsung HT-J4100 Manuel utilisateur

Samsung HT-J4100 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents