AR Blue Clean AR112S Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur
Questions, problems, missing parts?
Before returning to your retailer, call our
customer service department at 1-866-235-5112,
8 a.m. - 5:00 p.m., CST, Monday - Friday.
www.arblueclean.com
1500 PSI
Electric Pressure Washer
ASSEMBLY, CARE AND
USE INSTRUCTIONS
Model AR 112 S
READ CAREFULLY
IMPORTANT: RETAIN THESE INSTRUCTIONS
AND ATTACH RECEIPT TO MANUAL FOR FUTURE
REFERENCE
92723-LQ
Product Specications ...................................................................................................... 2
Package Contents ............................................................................................................. 3
Hardware Contents ........................................................................................................... 3
Safety Information ............................................................................................................. 4
Assembly Instructions ....................................................................................................... 6
Operating Instructions .....................................................................................................11
Care and Maintenance ................................................................................................... 13
Pump Saver ..................................................................................................................... 14
Troubleshooting ............................................................................................................... 15
Limited Warranty ............................................................................................................. 16
Replacement Parts List .................................................................................................. 17
2
TABLE OF CONTENTS
SPECIFICATIONS
Model
Rated PSI
(lbs/sq. in.)
Max GPM
(Gal/per min) Cold Water Volts Amps
Weight (lbs.)
AR 112 S 1500 1.4
120 12 15
PRODUCT SPECIFICATIONS
3
PACKAGE CONTENTS
HARDWARE CONTENTS
PART DESCRIPTION QUANTITY
I Variable Spray Nozzle Lance 1
J Extension Lance 1
K Clear Quick Connect with
Filter
1
L Garden Hose Adapter 1
M Nozzle Cleaning Wire 1
N O-Ring Kit 1
AA Screws 2
PART DESCRIPTION QUANTITY
A Spray Gun Holster 1
B Handle 1
C Power Washer Unit 1
D Cord Hook 1
E High Pressure Hose 1
F Spray Gun 1
G Spray Gun Lock/Unlock 1
H Detergent Bottle 1
OFF/O
ON/I
1500 PSI
E
F
H
B
C
M
A
J
I
L
G
K
D
N
AA
O-Rings
AA
Screw
Qty. 2
Note: Screws are located in
manual package
4
SAFETY INFORMATIONSAFETY INFORMATION
Please read and understand this entire manual before
attempting to assemble, operate, or install the product.
This manual contains information that relates to
PROTECTING PERSONAL SAFETY and PREVENTING
EQUIPMENT PROBLEMS. It is very important to read this
manual carefully and understand it thoroughly before
using the product. The symbols listed below are used to
indicate this information.
DANGER
Potential hazard that will result in serious injury or
loss of life.
WARNING
Hazard that could result in serious injury or loss of
life.
CAUTION
Potential hazard that may result in moderate injury
or damage to equipment.
Note: The word “Note” is used to inform the reader of
something the operator needs to know about the tool.
WARNING
To reduce the risk of injury, the user must read
and understand the instructions before using
this product.
1. Warning – When using this product basic,
precautions should always be followed, including the
following
2. Read all the instructions before using the product
3. Know how to stop the product and bleed pressures
quickly. Be thoroughly familiar with the controls.
4. Keep operating area clear of persons
5. Do not overreach or stand on unstable support. Keep
good footing and balance at all times.
6. Follow the maintenance instructions as specied in
the manual
7. To avoid personal injury and/or damage to property
and to maximize your power washing experience,
carefully follow all of the safety tips, instructions,
warnings and safeguards and become familiar with
all of the controls.
8. This power washer conforms to CSA and other safety
and consumer standards. DO NOT modify or rebuild
any part of your power washer.
9. DO NOT use your power washer when you are under
the inuence of alcohol or drugs. Use this power tool
carefully and only when you are alert.
10. Watch your balance and footing while using your
power washer. Surfaces become slippery when wet
and are extra slippery when using a detergent or
cleaner.
11. NEVER operate the power washer in bare feet,
sandals, or open-toed shoes.
12. When using the power washer near children, make
sure they are closely supervised by an adult to avoid
injury. NEVER let a child use the power washer.
13. Keep ngers, hands, feet and any part of your body
clear of the stream of high pressure water. The
powerful spray can cause blindness or blast holes in
the skin. It can break a window if you are too close
when you pull the trigger on the spray gun.
14. ALWAYS wear eye protection to prevent injury to
eyes when operating the power washer.
15. To avoid mishaps or injury, ALWAYS use the trigger
safety lock when not using the power washer even if
the spraying stops for a moment.
16. The power washer is equipped with a Ground Fault
Circuit Interrupter (GFCI) which greatly reduces the
chance of electric shock while the unit is in use. If
replacement of the plug or cord is needed, use only
identical replacement parts.
17. Point the spray gun in a safe direction when
beginning a power washing session.
18. NEVER spray directly at a person, animal, electrical
device or the unit itself.
19. When rst using the spray gun, hold the spray gun
and lance with two hands when pulling the trigger
(one hand to pull the trigger and the other to
stabilize the gun assembly) until you get used to the
“kickback” from the spray gun.
20. When you press the power switch to turn off the
power washer, water pressure may remain in the
system. To discharge the pressure, point the spray
gun in a safe direction and pull the trigger.
21. NEVER spray ammable liquids.
22. NEVER use the power washer in areas that contain
combustible dust, liquids or vapors.
23. Avoid contact of the pressure hose with sharp
objects and examine the hose regularly. Replace
if damaged. Due to the high pressure involved, it
cannot be repaired if cut or damaged.
24. Only use detergent specically formulated for power
washers and follow instructions on the detergent’s
label.
25. Protect eyes, lungs, and skin from exposure to
SAFETY INFORMATION
5
Double Insolated Product
SAFETY INFORMATIONSAFETY INFORMATION
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
detergent. Dish or laundry soap is too thick and will clog
the nozzle of your detergent bottle.
IMPORTANT: Store the power washer indoors to
prevent the water in the unit from expanding under
freezing conditions. When the water freezes and
expands, your power washer will be damaged and
become inoperable. Or, if storing outdoors, it is
recommended you use pump saver (not included) to
protect pumps.
26. NEVER use hot water with your power washer. It will
overheat and damage the high pressure pump.
27. NEVER leave the power washer unattended while it
is powered “ON”.
28. ALWAYS turn the water supply “ON ” before turning
the power washer power to “ON”. Running the pump
dry will cause damage to the internal components.
29. NEVER use a water supply to your power washer
that exceeds 150 PSI maximum.
30. NEVER disconnect the high pressure hose from the
power washer while the system is pressurized.
31. NEVER permanently engage the trigger mechanisms
on the spray gun.
32. NEVER operate the power washer unless all
components are properly and securely connected.
33. NEVER allow the power washer pump to run for
more than one minute after you have turned off the
water supply. This can cause the motor and pump to
overheat and fail.
34. NEVER use lances or other parts that are not
compatible for this specic AR Blue Clean unit.
35. NEVER use an extension power cord since it defeats
the effectiveness of the GFCI and increases the
chance of electrocuting the operator.
36. NEVER spray any electrical outlet with your power
washer.
37. Inspect the power cord before using. DO NOT use it
if it is damaged.
Servicing of a Double-Insulated Appliance
Ground Fault Circuit Interrupter Protection:
This pressure washer is provided with a ground-fault
circuit-interrupter (GFCI) built into the plugs of the
power-supply cord. This device provides additional
protection from the risk of electric shock. Should
replacement of the plug or cord become necessary,
use only identical replacement parts that include GFCI
protection.
In a double-insulated product, two systems of insulation
are provided instead of grounding. Grounding means
are not provided for a double insulated product, nor
should grounding means be added to the product.
Servicing a double-insulated product requires extreme
care and knowledge of the system, and should only be
done by qualied service personnel.
Replacement parts for a double-insulated product must
be identical to the original parts.
A double-insulated product is marked with the words
“Double Insulation” or “Double Insulated”. Product may
also be marked with symbol shown here.
6
ASSEMBLY INSTRUCTIONS
Power Unit Assembly
Install handle (B) to power washer unit (C).
Secure with screws (AA).
Note: DO NOT use a power screwdriver. When the
screw is completely tight, give a small nal clockwise
twist of the screwdriver. DO NOT overtighten.
1
C
B
AA
Screw x 2
AA
AA
Screw
Qty. 2
OFF/O
ON/I
1500 PSI
2
C
A
Slide spray gun holster (A) onto left side,when facing unit,
of power washer unit (C) as shown.
Note: This step does not require any screws.
Hardware Used:
PREPARATION
Before beginning assembly of product, make sure all
parts are present. Compare parts with package contents
list and hardware contents list. If any part is missing or
damaged, DO NOT attempt to assemble the product.
Estimated Assembly Time: 5 minutes
Tools Required for Assembly (not included): Phillips
screwdriver
PREPARATION
7
ASSEMBLY INSTRUCTIONS
OFF/O
ON/I
1500 PSI
3
C
D
Slide cord hook holster (D) onto right side, when facing
unit, of power washer unit (C) as shown.
Note: This step does not require any screws.
4
C
E
High Pressure Hose Assembly
Screw high pressure hose (E) clockwise onto bottom
front of power washer unit (C). Pull back collar and insert
o-ring post into water outlet far enough so collar can
thread onto outlet threads until hand tight. If it takes
fewer than six turns you have not properly tightened the
high pressure hose tting. It is easier to position the
power washer in front of you to ensure that the threads
are started correctly. Failure to properly tighten high
pressure hose will result in the hose slipping or popping
off immediately upon turning unit on. Do not worry about
damage if this occurs–just reinstall and take extra care
when screwing on the high pressure hose tting.
Note: DO NOT use pliers or locking pliers to tighten.
5
E
F
Connect the other end of high pressure hose (E) to
spray gun (F) by inserting the silver metal tip of high
pressure hose into the tting just ahead of trigger
guard. It will lock into spray gun with a “click”. Conrm
hose is locked into spray gun by slightly pulling on
hose. The hose is now securely attached to spray gun.
Note: DO NOT press button on underside of gun when
connecting hose to gun.
2
1
6
E
F
To release hose (E) from spray gun (F), press button on
underside of gun toward trigger guard. The hose will
slide out from connection.
8
ASSEMBLY INSTRUCTIONS
Locking Spray Gun (before Lance installation)
To lock trigger of spray gun (F), point gun away from you
and press bottom half of lock button to engage lock.
Squeeze or pull trigger to make sure it is locked.
ALWAYS leave lock button in locked position when not
in use. This ensures the gun is in “safe” mode until it is
ready for use. To unlock, press top half of lock button to
release.
Note: The trigger lock prevents trigger from being ac-
cidentally engaged.
Lock
Unlock
7
F
F
1
2
8
J
F
Extension Lance installation
With spray gun (F) in locked position, attach extension
lance (J) directly to spray gun. Insert lance extension
into gun, pushing together and turning clockwise
simultaneously. Turn the extension collar clockwise
to lock into place. To remove extension lance (J), turn
extension collar counterclockwise to unlock, then push
together and turn counterclockwise to release.
Note: The extension lance must be inserted in gun
before using any of the other attachments, and
in place for storage. It is recommended that once
extension is connected to leave it in place.
9
ASSEMBLY INSTRUCTIONS
2
1
9
I
J
Variable Spray Nozzle Lance installation
Insert variable spray nozzle lance (I) or detergent bottle
(H) into the end of the extension lance by inserting and
pushing together turning clockwise simultaneously. To
remove push together and turn counterclockwise.
Note: Push the safety lock button to lock the trigger
when changing lances to ensure that they do not
accidentally eject with force during removal.
12
C
K
Garden Hose Adapter Installation
Remove plastic shipping cover on water inlet on back
of power washer unit (C). Install the clear quick connect
(K) to water inlet by hand, tightening clockwise.
Insert detergent bottle (H) into extension lance (J),
push in and turn clockwise
10
2
1
H
Detergent Bottle Installation
The detergent bottle comes with a straw which is tted
into screw-on top. If you do not see the straw, look
inside the bottle and attach it to the screw-on top. When
using detergent bottle, ll it with a properly formulated
detergent or cleaner with a water ratio according to
instructions on the container.
Pressure washer detergents are recommended. See
page 13 for more information.
DO NOT use thick or gel-like detergents as they will
clog the power washer and can cause damage.
1
J
H
11
2
10
ASSEMBLY INSTRUCTIONS
14
K
L
Attach a garden hose to garden hose adapter (L).
Note: Flush out garden hose before connecting
to QC garden hose adapter.
2
1
13
L
Push the QC garden hose adapter (L) onto the clear
quick connect (K). It will “click” into place. Do not pull
the blue sleeve back while pushing QC garden hose
adapter (L) onto clear quick connect (K).The water is now
connected to your power washer.
Note: To remove water hose, pull back on blue collar
and it will slide off the clear quick connect. This can be
done at any time. Water will not come out of the garden
hose as the blue/black collar has a water stop check
valve. Water will only ow from the garden hose when it
is connected to the clear quick connect (K).
You have now completed the assembly and are ready
to begin using your electric power washer. Read and
observe all safety instructions.
11
OPERATING INSTRUCTIONS
Turn on water supply at the faucet to completely
open.
Make sure the “ON/OFF” switch is in the “OFF”
position. The power switch has international symbols
for ‘on’ and ‘off’: On (|) Off (O).
Unwind the power cord completely and plug the GFCI
into a grounded 120 volt outlet.
Release the safety lock button on the spray gun by
pressing the top half of the safety lock button. While
pointing the spray gun in a safe direction, squeeze
the trigger on the spray gun until there is a steady
stream of water, letting the water and air out of the
hose.
Turn the power switch to the “ON” (|) position. The
unit will turn on for 1 - 2 seconds and shut off. This is
a normal function of the auto start feature. Squeeze
the spray gun trigger to begin pressure washing.
Unlock
F
OFF/0
ON/I
OFF/0
ON/I
12
OPERATING INSTRUCTIONSOPERATING INSTRUCTIONS
Begin power washing by squeezing the trigger on the
spray gun all the way into the handle.
• Release the spray gun trigger to stop the power washer
Allow the motor to come to a complete stop before
squeezing the trigger again.
Squeezing rapidly will cause the auto start feature to
miss an on/off cycle that may prevent it from turning
on while squeezing trigger after rapid squeezing. Use
slow deliberate trigger pulls to avoid such symptoms.
Always test a small area to avoid chance of damaging
the surface.
When using the variable spray nozzle, the spray
pattern and intensity can be adjusted for each task by
twisting the spray nozzle at the far end of the lance.
Operation Tips
If you hear the motor run intermittently when the
trigger is not being squeezed, that is normal. The
pump is priming itself so it is ready to operate when
the trigger is squeezed. Turn off the power washer if
not being used after ve minutes.
The o-rings on the bayonet end of the nozzle should
be cleaned regularly and lubricated with non-water
soluble grease such as petroleum jelly.
Keep the nozzle cleaning wire for use in unclogging
the nozzle. If you lose the cleaning wire, a
straightened paper clip also works.
How to Avoid Damaging Surfaces
Damage to surfaces being cleaned occurs because
the impact force of the water pressure exceeds
the durability of the surface. Bare wood can be
penetrated; paint can be peeled off, etc. You can vary
the force of your power washer by controlling:
1. The angle of the surface being cleaned
2. The distance of the nozzle from the
surface being cleaned
NEVER use a narrow high pressure stream of water
on soft surfaces susceptible to damage.
13
CARE AND MAINTENANCE
Detergents
Use detergents designed for power washers. These
can be purchased online at our website www.
arblueclean.com. Hardware stores or home centers
also have power washer detergents for different
cleaning projects. The cleaning solution should be
the consistency of water in order to prevent clogging
your detergent bottle and nozzle.
This system applies detergent under low pressure.
The cleaning power of the detergents is enhanced
when applied with low pressure and enough time is
given to break down dirt and grime. The combination
of low pressure and chemical action is very effective
and can be better than scrubbing if applied properly.
ALWAYS spray detergent on a dry surface. DO NOT
pre-soak area. Wetting the surface rst dilutes
the detergent and reduces its cleaning ability. DO
NOT allow detergent to dry on surface. On vertical
surfaces being cleaned, apply detergent to lower
surfaces and work your way up to prevent detergent
from causing streaks in the dirt and grime. Rinse
detergent by pressure washing from bottom up for
same reason.
If a stain is particularly tough, it may be necessary
to reapply the detergent and use a bristled brush to
scrub the stain. Subsequent power washing after
brushing should successfully complete your cleaning
job.
Cleaning Clear Quick Connect
The screens inside the adapter should be cleaned
periodically. Rinse it with clean water, and then place
it back in the adapter.
Cleaning Nozzles
A clogged or partially clogged nozzle can cause
signicant reduction of water pressure coming out
of the nozzle and/or cause the unit to pulsate while
spraying.
Turn off the unit.
Turn off the water supply to the unit.
Relieve any pressure trapped in the hose by squeezing
the trigger 2-3 times, and then lock the spray gun by
pushing the lock button from left to right.
• Remove the lance from the extension lance
Take off the variable spray nozzle lance. Rotate the
nozzle to narrow the stream setting which opens up
the fan blades
Using the nozzle tip cleaner provided (or an unfolded
paper clip), insert the wire into the nozzle hole and
move back and forth until debris is dislodged.
Tap quick connect end of lance on hard surface
several times
Back ush water through the nozzles using garden
hose and highest pressure available (either standard
water nozzle or use your thumb over the nozzle to
create water pressure for back ush).
CARE AND MAINTENANCE
14
PUMP SAVER
Pump Saver is a product that protects and prolongs
the life of the pump. This will keep the internal parts
of the pump lubricated and protected from freezing
while being stored in ALL climates. It also assists with
protection from internal corrosion. The Blue Clean part
# is: PW64511 (16oz. bottle). Order online at www.
arblueclean.com
Pump Saver Instructions
Follow the previous storage instructions for your power
washer. To prevent staining, protect the surface under
the power washer from any excess uid. Wear eye
protection when using this product.
Turn unit off and disconnect all hoses before adding
pump protector. Unscrew threaded top from bottle to
remove seal and reattach threaded top to bottle.
Remove black cap from bottle.
1) Screw garden hose adapter (L) clockwise onto
threaded top of pump saver bottle.
2) To connect, push garden hose adapter (L) and pump
saver bottle rmly into clear quick connect lter (K),
previously installed to pressure washer inlet.
3)
Turn power on. Turn the power washer off as soon as
the pump saver begins to exit the pump outlet.
Note: Instructions on Pump Saver Bottle are generic and
not model specic.
2
1
K
L
Storage
When your pressure washing session has been
completed, turn off the power switch located on the
front of the power washer. Unplug the power cord
from the outlet. Turn off the water supply. Pull the
trigger on the spray gun 2-3 times to drain out the
excess water and to release any remaining water
pressure. Disconnect the garden hose adapter from
the water inlet. DO NOT allow the power washer to
run with no water owing through it.
Remove detergent bottle and clean completely.
Residual chemical will stick to the container and can
cause the detergent injector to clog and not function
properly.
Remove high pressure hose from spray gun.
Remove lance from the gun. Place the gun in the
holder on the side. Lances are placed into any of the
slots in the back of the unit. Make sure to discard
any remaining detergent from the bottle. Flush the
bottle and nozzle head with fresh water to prevent
clogging.
Hook the power cord around the cord hook on the
right side of the machine when facing it.
PROBLEM CORRECTIVE ACTION
Unit will not turn on. 1. The GFCI module on the end of the power cord must be plugged directly into an outlet.
2. Do not use an extension cord.
3. With the GFCI Connected make sure the power switch is turned on.
Note: When power switch is turned on, the power washer will turn on by itself for 1-2
seconds and shut off. This is normal.
The high pressure
(HP) hose will
not connect/stay
connected to the
spray gun. Is this a
spray gun problem?
1. In most cases, the spray gun is not the problem. The problem is the rubber sleeve
covering the tting at the end of the high pressure hose. It has likely slipped up toward
the metal tip. To x: wiggle, twist and/or pull the rubber sleeve down until the entire tip
is visible plus an 1/8 in. of the metal tting below the tip. Now try to insert the hose tip
into the spray gun. It should “click” into place and will not come out until the hose is
released by pushing in the lever on the underside of the gun. You may cut away the end
of the sleeve with a sharp knife if unable to move the sleeve down. Be careful not to cut
or puncture the hose.
2. Do not push in the release button when connecting the high pressure hose.
The unit is running
but there is no water
ow.
1. Check the water source. Unclog the nozzle on the lance. (See nozzle cleaning
instructions under “Cleaning nozzles”.) Or take off the lance and just spray out of the
spray gun. This will indicate if the problem is with the lance.
2. Reconnect the QC Garden Hose Adapter to the clear quick connect.
Why is water leaking
where the high
pressure hose
connects to the spray
gun?
1. Make sure there is an o-ring at the end of the metal tip of the high pressure hose. If
no o-ring is present, the connection between the hose and spray gun will leak. O-Ring
Kits are available online at www.arblueclean.com or call Customer Service at 1-866-
235-5112 to place an order.
I can’t remove the
lance from the spray
gun. What should I
do?
1. All lances and the detergent bottles are attached and removed from the extension
lance in the same manner. Insert the quick-release end of the lance/detergent bottle
into the extension lance. Press the extension lance and lance together (about a 1/8”)
and turn clockwise. The lance will lock in place. Remove the lance by reversing this
procedure. Press the extension lance and lance together and turn counter clockwise.
The lance will slide out.
2. Or, hold the extension lance and lance in an upright position with the nozzle end on
the oor. Push the whole assembly straight down to loosen the connection, and then
follow the removal process again. You may also spray soapy water or a lubricant in the
area where the lance connects to the extension lance.
The power washer
turns on for
2 seconds, shuts
off, and will not turn
back on. Do I have a
defective unit?
1. It sounds like your power washer is working just ne. When the water is connected,
the accessories are assembled properly, and the power switch is turned on, the power
washer may turn on for 1 - 2 seconds to prime the pump. It automatically shuts off and
waits for the spray gun trigger to be pressed. When the trigger is pressed, water starts
owing through the pump. The water sensor in the pump “senses” the moving water
and automatically turns the power washer on.
2. Turn the power switch to off, hold in the trigger on the spray gun, so that you have a
steady stream of water. While you are holding the trigger open on the spray gun, at the
same time, turn the power switch on.
If you have any questions regarding the product, please call customer service at 1-866-235-5112.
TROUBLESHOOTING
15
LIMITED WARRANTY
This product is under warranty to the original retail consumer against defects in material and workmanship for a
period of 1 (one) year and is a complete “bumper to bumper” warranty including the spray gun, the high pressure
hose and all accessories from the date of purchase. The warranty is not transferable or assignable. This warranty
covers replacement parts. This limited one year warranty applies only to products used in consumer applications
and is void in rental or any commercial application. Reasonable care must be used in conformity with operation and
maintenance instructions in the owner’s manual and quick start guide. Failure to follow these instructions will void
this warranty. This warranty gives you specic legal rights and you may also have other rights which vary from state to
state.
Warranty Process
Keep your original receipt of purchase in case of warranty claim.
If your power washer develops a problem, contact Customer Service:
Call our toll-free number at 1-866-235-5112. Customer Service is available Monday - Friday 8:00 a.m. to 5:00 p.m.
Central Standard Time (CST). The Customer Service person will work with you to x the problem.
If the power washer needs to be returned for repair, shipping costs to the company must be paid by the customer. A
Return Merchandise Authorization (RMA) Number will be issued for the return. Upon receiving the power washer,
the company will repair or replace the unit. We will send unit back to customer at no charge.
Please note: Power washers sent to the company without an RMA Number will NOT be accepted and shipped
back at the expense of the sender.
16
17
REPLACEMENT PARTS LIST
Printed in China
For replacement parts, call our customer service department at 1-866-235-5112, 8 a.m. - 5:00 p.m., CST,
Monday - Friday or order online at www.arblueclean.com
PART DESCRIPTION PART #
G Cord Hook PW4220590
H Clear Quick Connect with
Filter
PW3082130
I QC Garden Hose Adapter PW3082731
J GFCI Assembly PW4221160
K O-Ring Kit PW909107K
PART DESCRIPTION PART #
A Detergent Bottle (14 oz.) PW50954
B Hose PW4220600
C Spray Gun PW4120391
D Variable Spray Nozzle
Lance
PW4120410
E Extension Lance PW4120400
F Gun Holster PW4220580
A
B
D
E
I
F
H
C
G
J
K
PW909107K
18
Questions, problèmes, pièces manquantes?
Avant de retourner l'appareil chez le marchand,
contactez notre service à la clientèle au
1 866-235-5112, de 8 h à 17 h (HNC) du lundi au
vendredi.
www.arblueclean.com
1500 PSI
LAVEUSE À PRESSION ÉLECTRIQUE
GUIDE D'ASSEMBLAGE,
D'ENTRETIEN ET
D'UTILISATION
Modèle AR 112 S
LIRE ATTENTIVEMENT
IMPORTANT : CONSERVER CE GUIDE ET
INSÉRER LA FACTURE DANS LE GUIDE POUR
RÉFÉRENCE ULTÉRIEURE.
92723-LQ
19
Spécications du produit ................................................................................................. 19
Contenu de l'emballage ...................................................................................................20
Matériel inclus ..................................................................................................................20
Consignes de sécurité .....................................................................................................21
Instructions d'assemblage ..............................................................................................23
Mode d’emploi .................................................................................................................28
Entretien et maintenance ................................................................................................ 30
Protecteur de pompe ....................................................................................................... 31
Dépannage .......................................................................................................................32
Garantie limitée ................................................................................................................33
Liste des pièces de rechange ..........................................................................................34
TABLE DES MATIÈRES
SPÉCIFICATIONS
Modèle PSI nominale
(k/cm2)
(lb/po2)
Débit maximum
(Litre/min)
(Gal./min)
Eau froide Volts A Poids
(kg)
(lb)
AR 112 S 4 389
(1 500)
5,3
(1,4)
120 12 6,8
(15)
SPÉCIFICATIONS DU PRODUIT
20
CONTENU DE L'EMBALLAGECONTENU DE L'EMBALLAGE
MATÉRIEL INCLUS
PIÈCE DESCRIPTION QUANTITÉ
I Lance d’arrosage à jet variable 1
J Rallonge pour lance d’arrosage 1
K Raccord rapide transparent avec
ltre
1
L Adaptateur de tuyau d’arrosage 1
M Tige de nettoyage de la buse 1
N Ensemble de joints toriques 1
AA Vis 2
PIÈCE DESCRIPTION QUANTITÉ
A Étui à pistolet pulvérisateur 1
B Poignée 1
C Laveuse à pression 1
D Crochet pour cordon d’alimentation 1
E Tuyau à haute pression 1
F Pistolet pulvérisateur 1
G Cran de verrouillage/déverrouillage 1
H Réservoir de détergent 1
OFF/O
ON/I
1500 PSI
E
F
H
B
C
M
A
J
I
L
G
K
D
N
AA
O-Rings
AA
Screw
Qty. 2
Remarque : Les vis se trouvent
dans l’emballage du manuel
Vis
Qté 2
1500 PSI
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

AR Blue Clean AR112S Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur