Wacker Neuson GP6600 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur

Ce manuel convient également à

Generator
GP 6600A
GPS 6600A
Non-CARB
OPERATOR’S MANUAL
0171951en 002
0609
0171951EN
DANGER
CARBON MONOXIDE
Using a generator indoors CAN KILL YOU IN MINUTES.
Generator exhaust contains carbon monoxide (CO). This is a poison you cannot see or
smell. If you can smell the generator exhaust, you are breathing CO. But even if you cannot
smell the exhaust, you could be breathing CO.
NEVER use a generator inside homes, garages, crawlspaces, or other partly enclosed
areas. Deadly levels of carbon monoxide can build up in these areas. Using a fan or
opening windows and doors does NOT supply enough fresh air.
ONLY use a generator outside and far away from windows, doors, and vents. These
openings can pull in generator exhaust.
Even when you use a generator correctly, CO may leak into the home. ALWAYS use a
battery-powered or battery-backup CO alarm in the home.
If you start to feel sick, dizzy, or weak after the generator has been running, move to fresh
air RIGHT AWAY. See a doctor. You could have carbon monoxide poison.
wc_tx000240gb.fm 3
Foreword
This manual provides information and procedures to safely operate
and maintain this Wacker Neuson model. For your own safety and
protection from injury, carefully read, understand and observe the
safety instructions described in this manual.
Keep this manual or a copy of it with the machine. If you lose this
manual or need an additional copy, please contact Wacker Neuson
Corporation. This machine is built with user safety in mind; however,
it can present hazards if improperly operated and serviced. Follow
operating instructions carefully! If you have questions about operating
or servicing this equipment, please contact Wacker Neuson
Corporation.
The information contained in this manual was based on machines in
production at the time of publication. Wacker Neuson Corporation
reserves the right to change any portion of this information without
notice.
All rights, especially copying and distribution rights, are reserved.
Copyright 2009 by Wacker Neuson Corporation.
No part of this publication may be reproduced in any form or by any
means, electronic or mechanical, including photocopying, without
express written permission from Wacker Neuson Corporation.
Any type of reproduction or distribution not authorized by Wacker
Neuson Corporation represents an infringement of valid copyrights
and will be prosecuted. We expressly reserve the right to make
technical modifications, even without due notice, which aim at
improving our machines or their safety standards.
wc_tx000240gb.fm 4
GP/GPS 6600A Table of Contents
5
Foreword 3
1. Safety Information 7
1.1 Laws Pertaining to Spark Arresters ...................................................... 7
1.2 Operating Safety .................................................................................. 8
1.3 Operator Safety while using Internal Combustion Engines .................. 9
1.4 Service Safety .................................................................................... 11
1.5 Label Locations .................................................................................. 12
1.6 Safety and Operating Labels .............................................................. 13
2. Operation 17
2.1 Determining Power Requirements ..................................................... 17
2.2 Installation .......................................................................................... 18
2.3 Recommended Battery (GPS only) .................................................... 18
2.4 Battery Installation (GPS only) ........................................................... 19
2.5 Wheel Kit ............................................................................................ 20
2.6 Generator Derating ............................................................................. 22
2.7 Grounding the Generator ................................................................... 23
2.8 Operating Heavy Loads ...................................................................... 23
2.9 Use of Extension Cords ...................................................................... 24
2.10 Control Panel ...................................................................................... 25
2.11 Ground Fault Circuit Interrupter (GFCI) .............................................. 26
2.12 Twist-Lock Receptacles ..................................................................... 27
2.13 Engine Auto Idle ................................................................................. 27
2.14 Engine Speed ..................................................................................... 27
2.15 Voltage Selection ............................................................................... 28
2.16 Before Starting ................................................................................... 29
2.17 To Start ............................................................................................... 30
2.18 To Stop ............................................................................................... 31
Table of Contents GP/GPS 6600A
wc_bo0171951en_002TOC.fm 6
3. Maintenance 32
3.1 Engine Maintenance ............................................................................32
3.2 Periodic Maintenance Schedule ..........................................................32
3.3 Engine Oil ............................................................................................33
3.4 Servicing Air Cleaner ...........................................................................34
3.5 Spark Plug ...........................................................................................35
3.6 Cleaning the Sediment Cup ................................................................36
3.7 Carburetor Adjustment ........................................................................37
3.8 Adjusting Engine Speed ......................................................................37
3.9 Storage ................................................................................................38
3.10 Transport .............................................................................................38
3.11 Troubleshooting ...................................................................................39
3.12 Wire Colors ..........................................................................................39
3.13 Electrical Schematic ............................................................................40
3.14 Electrical Schematic (CAN models only) .............................................42
3.15 Engine Schematic ...............................................................................44
4. Technical Data 47
4.1 Generator ............................................................................................47
4.2 Engine .................................................................................................49
GP/GPS 6600A Safety Information
7
1. Safety Information
This manual contains DANGER, WARNING, CAUTION, NOTICE, and
NOTE callouts which must be followed to reduce the possibility of
personal injury, damage to the equipment, or improper service.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
NOTICE: Used without the safety alert symbol, NOTICE indicates a
situation which, if not avoided, could result in property damage.
Note: Contains additional information important to a procedure.
1.1 Laws Pertaining to Spark Arresters
Notice: State Health Safety Codes and Public Resources Codes
specify that in certain locations spark arresters be used on internal
combustion engines that use hydrocarbon fuels. A spark arrester is a
device designed to prevent accidental discharge of sparks or flames
from the engine exhaust. Spark arresters are qualified and rated by
the United States Forest Service for this purpose.
In order to comply with local laws regarding spark arresters, consult
the engine distributor or the local Health and Safety Administrator.
DANGER
WARNING
CAUTION
Safety Information GP/GPS 6600A
8
1.2 Operating Safety
Using a generator indoors CAN KILL YOU IN MINUTES. Generator
exhaust contains carbon monoxide. This is a poison you cannot see or
smell. NEVER use this generator inside a home or garage, EVEN IF
doors and windows are open. Only use this generator OUTSIDE and
far away from windows, doors, and vents.
BACKFEED FROM THE GENERATOR INTO THE PUBLIC POWER
DISTRIBUTION SYSTEM CAN CAUSE SERIOUS INJURY OR
DEATH TO UTILITY WORKERS!
Improper connection of generator to a building’s electrical system can
allow electrical current from the generator to backfeed into utility lines.
This may result in electrocution of utility workers, fire, or explosion.
Connections to a building’s electrical system must be made by a
qualified electrician and comply with all applicable laws and electrical
codes.
If connected to a building’s electrical system the generator must meet
the power, voltage, and frequency requirements of the equipment in
the building. Differences in power, voltage, and frequency
requirements may exist and improper connection may lead to
equipment damage, fire, and personal injury or death.
Familiarity and proper training are required for the safe operation of the
machine. Machines operated improperly or by untrained personnel
can be hazardous. Read the operating instructions contained in this
manual and the engine manual, and familiarize yourself with the
location and proper use of all controls. Inexperienced operators should
receive instruction from someone familiar with the machine before
being allowed to operate it.
1.2.1 NEVER operate the generator when open containers of fuel, paint, or
other flammable liquids are near.
1.2.2 NEVER operate the generator, or tools attached to the generator, with
wet hands.
1.2.3 NEVER use worn electrical cords. Severe electrical shock and
equipment damage may result.
1.2.4 NEVER run the electrical cords under the generator, or over vibrating
or hot parts.
1.2.5 NEVER enclose or cover the generator when it is in use or when it is
hot.
1.2.6 NEVER overload the generator. The total amperage of the tools and
equipment attached to the generator must not exceed the load rating
of the generator.
1.2.7 NEVER operate the machine in snow, rain, or standing water.
DANGER
DANGER
WARNING
GP/GPS 6600A Safety Information
9
1.2.8 NEVER allow untrained personnel to operate or service the generator.
The generator set should be set up by a certified electrician.
1.2.9 NEVER stand on the machine.
1.2.10 DO NOT stand under the machine while it is being hoisted or moved.
1.2.11 DO NOT attach equipment to the machine when it is suspended.
1.2.12 Store the machine properly when it is not being used. The machine
should be stored in a clean, dry location out of the reach of children.
1.2.13 ALWAYS position and operate the generator on a firm,
noncombustible, level surface.
1.2.14 ALWAYS transport the generator in an upright position.
1.2.15 ALWAYS keep the machine at least one meter (three feet) away from
structures, buildings, and other equipment during use.
1.2.16 ALWAYS keep the area immediately surrounding and underneath the
machine clean, neat, and free of debris and combustible materials.
Make sure that the area overhead is clear of debris that could fall onto
or into the machine or exhaust compartment.
1.2.17 ALWAYS remove all tools, cords, and other loose items from the
generator before starting it.
1.2.18 ALWAYS make certain the machine is well-grounded and securely
fastened to a good earthen ground per national and local regulations.
1.3 Operator Safety while using Internal Combustion Engines
Internal combustion engines present special hazards during operation
and fueling. Read and follow the warning instructions in the engine
owner’s manual and the safety guidelines below. Failure to follow the
warnings and safety standards could result in severe injury or death.
1.3.1 NEVER use this generator inside a home or garage, EVEN IF doors
and windows are open. Only use OUTSIDE and far away from
windows, doors, and vents. Using a generator indoors CAN KILL YOU
IN MINUTES. Generator exhaust contains carbon monoxide. This is a
poison you cannot see or smell.
1.3.2 NEVER use a generator inside an enclosed area such as a tunnel or a
trench.
1.3.3 Do not smoke while operating the machine.
1.3.4 Do not smoke when refueling the engine.
1.3.5 Do not refuel a hot or running engine.
1.3.6 Do not refuel the engine near an open flame.
1.3.7 Do not spill fuel when refueling the engine.
1.3.8 Do not run the engine near open flames.
WARNING
Safety Information GP/GPS 6600A
10
1.3.9 Do not start the engine if fuel has spilled or a fuel odor is present. Move
the generator away from the spill and wipe the generator dry before
starting.
1.3.10 Refill the fuel tank in a well-ventilated area.
1.3.11 Replace the fuel tank cap after refueling.
1.3.12 ALWAYS check the fuel lines and the fuel tank for leaks and cracks
before starting the engine. Do not run the machine if fuel leaks are
present or the fuel lines are loose.
GP/GPS 6600A Safety Information
11
1.4 Service Safety
Poorly maintained equipment can become a safety hazard! In order
for the equipment to operate safely and properly over a long period of
time, periodic maintenance and occasional repairs are necessary. If
the generator is experiencing problems or is being serviced, attach a
“DO NOT START” sign to the control panel to notify other people of its
condition.
1.4.1 Do not use gasoline or other types of fuels or flammable solvents to
clean parts, especially in enclosed areas. Fumes from fuels and
solvents can become explosive.
1.4.2 DO NOT attempt to clean or service the machine while it is running.
1.4.3 Do not modify the machine without the express written approval of the
manufacturer.
1.4.4 DO NOT allow water to accumulate around the base of the machine.
If water is present, move the machine and allow the machine to dry
before servicing.
1.4.5 DO NOT service the machine if your clothing or skin is wet.
1.4.6 DO NOT allow untrained personnel to service this equipment. Only
trained electrical technicians should be allowed to service the electrical
components of this equipment.
1.4.7 Keep the machine clean and labels legible. Replace all missing and
hard-to-read labels. Labels provide important operating instructions
and warn of dangers and hazards.
1.4.8 ALWAYS replace the safety devices and guards after repairs and
maintenance.
1.4.9 ALWAYS let the engine cool before transporting or servicing the
machine.
1.4.10 ALWAYS keep hands, feet, and loose clothing away from the moving
parts on the generator and engine.
1.4.11 ALWAYS turn the engine off before servicing the machine. If the
engine has electric start, disconnect the negative terminal on the
battery before servicing the machine.
1.4.12 ALWAYS keep the fuel lines in good condition and properly connected.
Leaking fuel and fumes are extremely explosive.
WARNING
Safety Information GP/GPS 6600A
12
1.5 Label Locations
GND
88897
GP/GPS 6600A Safety Information
13
1.6 Safety and Operating Labels
Wacker Neuson machines use international pictorial labels where
needed. These labels are described below:
Label Meaning
WARNING!
Hot surface!
CAUTION
Lifting point.
Electrical ground
Press circuit breaker switch to OFF position.
Check the fuel level.
GND
88897
Safety Information GP/GPS 6600A
14
Open the fuel flow valve.
Press engine switch to ON position.
GPS - Press ignition switch.
GP - Pull the rewind starter.
Press circuit breaker switch to ON position.
Press engine switch to OFF position.
Close the fuel flow valve.
Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains car-
bon monoxide. This is a poison you cannot see or smell.
NEVER use inside a home or garage, EVEN
IF doors and windows are open.
Label Meaning
GP/GPS 6600A Safety Information
15
Only use OUTSIDE and far away from win-
dows, doors, and vents.
WARNING!
To reduce the risk of electrical shock and arc
flash, read the Operator’s Manual. Improper
connection of the generator to a building’s
electrical system can allow electrical current
from the generator to backfeed into utility lines.
This may result in electrocution of utility work-
ers, fire, or explosion. Connections to a build-
ing’s electrical system must be made by a
qualified electrician and comply with all appli-
cable laws and electrical codes.
A nameplate listing the model number, item
number, revision number, and serial number is
attached to each unit. Please record the infor-
mation found on this plate so it will be avail-
able should the nameplate become lost or
damaged. When ordering parts or requesting
service information, you will always be asked
to specify the model number, item number,
revision number, and serial number of the unit.
This equipment does not meet California EVP
emission regulations for small off-road
engines.
This machine may be covered by one or more
patents.
Label Meaning
Safety Information GP/GPS 6600A
16
DANGER!
No sparks, flames or burning objects near
machine.
Shut off the engine before refueling.
Read the Operator’s Manual for machine infor-
mation.
GFCI TEST INSTRUCTIONS - TEST BEFORE EACH USE
Normal operating state - sensing device green LED is "ON" and circuit breaker is at "ON"
position.
Step 1: Press "TEST" button. Green LED should go "OUT" and red LED should come
"ON" and circuit breaker should trigger to "OFF" position.
Step 2: If sensing device LED or breaker does not trip or change state, "DO NOT USE".
Consult an electrician for assistance.
Step 3: Press "RESET" button. Red LED should turn "OFF" and green LED should turn
"ON".
Step 4: Manually reset (switch) circuit breaker to "ON" position to restore circuit power.
Label Meaning
GP/GPS 6600A Operation
17
2. Operation
2.1 Determining Power Requirements
This generator is designed to operate single-phase, 60 Hz appliances
running at 120 VAC or 240 VAC. Check the nameplate or label
provided on tools and appliances to make sure their power
requirements match the power output of the generator.
Some appliances and tools require a surge of current when starting.
This means that the amount of power needed to initially start the
equipment is larger than the power required to keep it running. The
generator must be capable of supplying this “surge” current. Other
types of appliances require more power than is actually stated on their
nameplate.
The information in “Approximate Starting Power Requirements” is
offered only as a general guideline to help you in determining power
requirements for different types of equipment. Check with your nearest
Wacker Neuson dealer, or contact the manufacturer or dealer of the
tool or appliance, with questions regarding its power requirements.
NOTICE: If a tool or appliance does not reach full speed within a few
seconds when switched on, turn it off immediately to avoid damage.
Approximate Starting Power Requirements
Incandescent lights and appliances such as irons and hot plates, which
use a resistive-type heating element, require the same wattage to start
and run as is stated on their nameplates.
Fluorescent and mercury lamps require 1.2–2 times their stated
wattage to start.
Electrical motors and many types of electrical tools often require a
large starting current. The amount of starting current depends on the
type of motor and its use.
Most electrical tools require 1.2–3 times their stated wattage for
starting.
Loads such as submersible pumps and air compressors require a very
large force to start. They need as much as 3–5 times the wattage
stated on the nameplate in order to start.
If the wattage is not given for a particular tool or appliance, it can be
calculated by multiplying its voltage and amperage requirements:
Single Phase: VOLTS x AMPS = WATTS
Operation GP/GPS 6600A
18
2.2 Installation
Place the generator in an area where it will not be exposed to rain,
snow, or direct sunlight. Make sure it is positioned on firm, level
ground, so it will not slide or shift. Position the engine exhaust away
from areas where people may be present.
The surrounding area must be free from water and moisture. All
components must be protected from excessive moisture.
Using a generator indoors CAN KILL YOU IN MINUTES. Generator
exhaust contains carbon monoxide. This is a poison you cannot see or
smell. NEVER use this generator inside a home or garage, EVEN IF
doors and windows are open. Only use this generator OUTSIDE and
far away from windows, doors, and vents.
NEVER install a generator in an enclosed area such as a tunnel or a
trench. Using a generator in a tunnel or a trench CAN KILL YOU IN
MINUTES. Generator exhaust contains carbon monoxide. This is a
poison you cannot see or smell. NEVER use this generator inside a
tunnel or a trench.
2.3 Recommended Battery (GPS only)
This generator is shipped without a battery. The recommended battery
to be used is:
Battery Type 50-N18L-A
Voltage 12 V
Capacity 20 A/h
L x W x H 206 x 90 x 164 mm
(8-1/8 x 3-9/16 x 6-7/16 in.)
DANGER
DANGERDANGER
GP/GPS 6600A Operation
19
2.4 Battery Installation (GPS only)
2.4.1 Align the holes found in the battery tray (a) to the holes on the frame
cross-member
2.4.2 Insert M8 x 14 screws (b) through the tray then through the holes of
the cross-member.
2.4.3 Insert the nuts (c) onto the screws and tighten. Torque nuts to 18.75
Nm. (13.5 ft.lbs).
2.4.4 Align the holes in the battery tube (d) to the holes in front of the battery
tray.
2.4.5 Insert M8 x 35 screws (e) through the battery tray then through the
tube.
2.4.6 Insert the nuts (f) onto the screws and tighten. Torque nuts to 18.75
Nm. (13.5 ft.lbs).
2.4.7 Insert the tube clamps (g) onto the upper frame tube and align the
holes to the holes of the battery tube.
2.4.8 Insert M8 x 35 screws (h) through the battery tube then through the
tube clamps.
2.4.9 Insert the nuts (j) onto the bolts and tighten. Torque nuts to 18.75 Nm.
(13.5 ft.lbs).
2.4.10 Slide the J-bolt (k) through the holes found in the battery holder (l).
2.4.11 Insert the rounded end of the J-bolt (k) into the slot of the battery tray
and insert the tip of the J-bolt through the hole.
Operation GP/GPS 6600A
20
2.5 Wheel Kit
The wheel kit (Part No. 0161308) is a standard item on Item Number
0620012, 0620015, 0620043 and 0620046 only. It is available as an
option on all other models.
2.5.1 Hoist the generator, and align the axle (c) with the lower cross-member
of frame.
2.5.2 Insert the axle brackets (k) over the axle and align the holes found in
the axle bracket to the holes of the cross-member. Ensure that the
brackets extend under the tube of the frame.
2.5.3 Insert M6 x 16 screws (l) through the outer holes on the cross-member,
then through the holes of the axle bracket.
2.5.4 Insert M6 nuts (m) onto the screws and tighten. Torque to 7.5 Nm (5.25
ft.lbs.).
2.5.5 Assemble the washers (g) next to the rings (h), then add the wheels
(d).
2.5.6 Add the washers (g) next to the wheels, then insert the pins (f) into the
holes of the axle and separate the legs of the pins.
2.5.7 Align the holes found in the leg bracket (b) to the holes of the lower
cross-member.
2.5.8 Insert M6 x 16 screws (l) through the outer holes on the cross-member,
then through the holes of the leg bracket.
2.5.9 Insert M6 nuts (n) onto the screws and tighten. Torque to 7.5 Nm (5.25
ft.lbs.).
2.5.10 Insert M8 x 30 screw (o) through the hole in the leg bracket and
through the hole in cross-member.
2.5.11 Insert M8 nut (p) onto the screw and tighten. Torque to 18.75 Nm (13.5
ft.lbs.).
2.5.12 Align the holes in the rubber foot mounts (e) to the holes of the leg
bracket.
2.5.13 Insert M6 x 20 screws (m) through the leg bracket, then through the
holes of the rubber foot mounts.
2.5.14 Insert the nuts (n) onto the screws and tighten. Torque to 7.5 Nm (5.25
ft.lbs.).
2.5.15 Align the holes found in the handles (a, j) to the holes of the brackets
(1) on the frame.
2.5.16 Insert M6 x 16 screws (l) through the handles, then through the
brackets on the frame.
2.5.17 Insert nuts (m) onto the screws and tighten. Torque to 7.5 Nm (5.25
ft.lbs.).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104

Wacker Neuson GP6600 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues