Wacker Neuson GP6600 Manuel utilisateur

Generator

GP 6600A

GPS 6600A

Non-CARB

OPERATOR’S MANUAL

0171951en 002

0609

0171951EN

DANGER

CARBON MONOXIDE

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide (CO). This is a poison you cannot see or

smell. If you can smell the generator exhaust, you are breathing CO. But even if you cannot

smell the exhaust, you could be breathing CO.

• NEVER use a generator inside homes, garages, crawlspaces, or other partly enclosed

areas. Deadly levels of carbon monoxide can build up in these areas. Using a fan or

opening windows and doors does NOT supply enough fresh air.

• ONLY use a generator outside and far away from windows, doors, and vents. These

openings can pull in generator exhaust.

Even when you use a generator correctly, CO may leak into the home. ALWAYS use a

battery-powered or battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator has been running, move to fresh

air RIGHT AWAY. See a doctor. You could have carbon monoxide poison.

wc_tx000240gb.fm 3

Foreword

This manual provides information and procedures to safely operate

and maintain this Wacker Neuson model. For your own safety and

protection from injury, carefully read, understand and observe the

safety instructions described in this manual.

Keep this manual or a copy of it with the machine. If you lose this

manual or need an additional copy, please contact Wacker Neuson

Corporation. This machine is built with user safety in mind; however,

it can present hazards if improperly operated and serviced. Follow

operating instructions carefully! If you have questions about operating

or servicing this equipment, please contact Wacker Neuson

Corporation.

The information contained in this manual was based on machines in

production at the time of publication. Wacker Neuson Corporation

reserves the right to change any portion of this information without

notice.

All rights, especially copying and distribution rights, are reserved.

No part of this publication may be reproduced in any form or by any

means, electronic or mechanical, including photocopying, without

express written permission from Wacker Neuson Corporation.

Any type of reproduction or distribution not authorized by Wacker

Neuson Corporation represents an infringement of valid copyrights

and will be prosecuted. We expressly reserve the right to make

technical modifications, even without due notice, which aim at

improving our machines or their safety standards.

wc_tx000240gb.fm 4

GP/GPS 6600A Table of Contents

5

Foreword 3

1. Safety Information 7

1.1 Laws Pertaining to Spark Arresters ...................................................... 7

1.2 Operating Safety .................................................................................. 8

1.3 Operator Safety while using Internal Combustion Engines .................. 9

1.4 Service Safety .................................................................................... 11

1.5 Label Locations .................................................................................. 12

1.6 Safety and Operating Labels .............................................................. 13

2. Operation 17

2.1 Determining Power Requirements ..................................................... 17

2.2 Installation .......................................................................................... 18

2.3 Recommended Battery (GPS only) .................................................... 18

2.4 Battery Installation (GPS only) ........................................................... 19

2.5 Wheel Kit ............................................................................................ 20

2.6 Generator Derating ............................................................................. 22

2.7 Grounding the Generator ................................................................... 23

2.8 Operating Heavy Loads ...................................................................... 23

2.9 Use of Extension Cords ...................................................................... 24

2.10 Control Panel ...................................................................................... 25

2.11 Ground Fault Circuit Interrupter (GFCI) .............................................. 26

2.12 Twist-Lock Receptacles ..................................................................... 27

2.13 Engine Auto Idle ................................................................................. 27

2.14 Engine Speed ..................................................................................... 27

2.15 Voltage Selection ............................................................................... 28

2.16 Before Starting ................................................................................... 29

2.17 To Start ............................................................................................... 30

2.18 To Stop ............................................................................................... 31

Table of Contents GP/GPS 6600A

wc_bo0171951en_002TOC.fm 6

3. Maintenance 32

3.1 Engine Maintenance ............................................................................32

3.2 Periodic Maintenance Schedule ..........................................................32

3.3 Engine Oil ............................................................................................33

3.4 Servicing Air Cleaner ...........................................................................34

3.5 Spark Plug ...........................................................................................35

3.6 Cleaning the Sediment Cup ................................................................36

3.7 Carburetor Adjustment ........................................................................37

3.8 Adjusting Engine Speed ......................................................................37

3.9 Storage ................................................................................................38

3.10 Transport .............................................................................................38

3.11 Troubleshooting ...................................................................................39

3.12 Wire Colors ..........................................................................................39

3.13 Electrical Schematic ............................................................................40

3.14 Electrical Schematic (CAN models only) .............................................42

3.15 Engine Schematic ...............................................................................44

4. Technical Data 47

4.1 Generator ............................................................................................47

4.2 Engine .................................................................................................49

GP/GPS 6600A Safety Information

7

1. Safety Information

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE callouts which must be followed to reduce the possibility of

personal injury, damage to the equipment, or improper service.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: Contains additional information important to a procedure.

1.1 Laws Pertaining to Spark Arresters

Notice: State Health Safety Codes and Public Resources Codes

specify that in certain locations spark arresters be used on internal

combustion engines that use hydrocarbon fuels. A spark arrester is a

device designed to prevent accidental discharge of sparks or flames

from the engine exhaust. Spark arresters are qualified and rated by

the United States Forest Service for this purpose.

In order to comply with local laws regarding spark arresters, consult

the engine distributor or the local Health and Safety Administrator.

DANGER

WARNING

CAUTION

Safety Information GP/GPS 6600A

8

1.2 Operating Safety

Using a generator indoors CAN KILL YOU IN MINUTES. Generator

exhaust contains carbon monoxide. This is a poison you cannot see or

smell. NEVER use this generator inside a home or garage, EVEN IF

doors and windows are open. Only use this generator OUTSIDE and

far away from windows, doors, and vents.

BACKFEED FROM THE GENERATOR INTO THE PUBLIC POWER

DISTRIBUTION SYSTEM CAN CAUSE SERIOUS INJURY OR

DEATH TO UTILITY WORKERS!

Improper connection of generator to a building’s electrical system can

allow electrical current from the generator to backfeed into utility lines.

This may result in electrocution of utility workers, fire, or explosion.

Connections to a building’s electrical system must be made by a

qualified electrician and comply with all applicable laws and electrical

codes.

If connected to a building’s electrical system the generator must meet

the power, voltage, and frequency requirements of the equipment in

the building. Differences in power, voltage, and frequency

requirements may exist and improper connection may lead to

equipment damage, fire, and personal injury or death.

Familiarity and proper training are required for the safe operation of the

machine. Machines operated improperly or by untrained personnel

can be hazardous. Read the operating instructions contained in this

manual and the engine manual, and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the machine before

being allowed to operate it.

1.2.1 NEVER operate the generator when open containers of fuel, paint, or

other flammable liquids are near.

1.2.2 NEVER operate the generator, or tools attached to the generator, with

wet hands.

1.2.3 NEVER use worn electrical cords. Severe electrical shock and

equipment damage may result.

1.2.4 NEVER run the electrical cords under the generator, or over vibrating

or hot parts.

1.2.5 NEVER enclose or cover the generator when it is in use or when it is

hot.

1.2.6 NEVER overload the generator. The total amperage of the tools and

equipment attached to the generator must not exceed the load rating

of the generator.

1.2.7 NEVER operate the machine in snow, rain, or standing water.

DANGER

WARNING

GP/GPS 6600A Safety Information

9

1.2.8 NEVER allow untrained personnel to operate or service the generator.

The generator set should be set up by a certified electrician.

1.2.9 NEVER stand on the machine.

1.2.10 DO NOT stand under the machine while it is being hoisted or moved.

1.2.11 DO NOT attach equipment to the machine when it is suspended.

1.2.12 Store the machine properly when it is not being used. The machine

should be stored in a clean, dry location out of the reach of children.

1.2.13 ALWAYS position and operate the generator on a firm,

noncombustible, level surface.

1.2.14 ALWAYS transport the generator in an upright position.

1.2.15 ALWAYS keep the machine at least one meter (three feet) away from

structures, buildings, and other equipment during use.

1.2.16 ALWAYS keep the area immediately surrounding and underneath the

machine clean, neat, and free of debris and combustible materials.

Make sure that the area overhead is clear of debris that could fall onto

or into the machine or exhaust compartment.

1.2.17 ALWAYS remove all tools, cords, and other loose items from the

generator before starting it.

1.2.18 ALWAYS make certain the machine is well-grounded and securely

fastened to a good earthen ground per national and local regulations.

1.3 Operator Safety while using Internal Combustion Engines

Internal combustion engines present special hazards during operation

and fueling. Read and follow the warning instructions in the engine

owner’s manual and the safety guidelines below. Failure to follow the

warnings and safety standards could result in severe injury or death.

1.3.1 NEVER use this generator inside a home or garage, EVEN IF doors

and windows are open. Only use OUTSIDE and far away from

windows, doors, and vents. Using a generator indoors CAN KILL YOU

IN MINUTES. Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

1.3.2 NEVER use a generator inside an enclosed area such as a tunnel or a

trench.

1.3.3 Do not smoke while operating the machine.

1.3.4 Do not smoke when refueling the engine.

1.3.5 Do not refuel a hot or running engine.

1.3.6 Do not refuel the engine near an open flame.

1.3.7 Do not spill fuel when refueling the engine.

1.3.8 Do not run the engine near open flames.

WARNING

Safety Information GP/GPS 6600A

10

1.3.9 Do not start the engine if fuel has spilled or a fuel odor is present. Move

the generator away from the spill and wipe the generator dry before

starting.

1.3.10 Refill the fuel tank in a well-ventilated area.

1.3.11 Replace the fuel tank cap after refueling.

1.3.12 ALWAYS check the fuel lines and the fuel tank for leaks and cracks

before starting the engine. Do not run the machine if fuel leaks are

present or the fuel lines are loose.

GP/GPS 6600A Safety Information

11

1.4 Service Safety

Poorly maintained equipment can become a safety hazard! In order

for the equipment to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary. If

the generator is experiencing problems or is being serviced, attach a

“DO NOT START” sign to the control panel to notify other people of its

condition.

1.4.1 Do not use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

1.4.2 DO NOT attempt to clean or service the machine while it is running.

1.4.3 Do not modify the machine without the express written approval of the

manufacturer.

1.4.4 DO NOT allow water to accumulate around the base of the machine.

If water is present, move the machine and allow the machine to dry

before servicing.

1.4.5 DO NOT service the machine if your clothing or skin is wet.

1.4.6 DO NOT allow untrained personnel to service this equipment. Only

trained electrical technicians should be allowed to service the electrical

components of this equipment.

1.4.7 Keep the machine clean and labels legible. Replace all missing and

hard-to-read labels. Labels provide important operating instructions

and warn of dangers and hazards.

1.4.8 ALWAYS replace the safety devices and guards after repairs and

maintenance.

1.4.9 ALWAYS let the engine cool before transporting or servicing the

machine.

1.4.10 ALWAYS keep hands, feet, and loose clothing away from the moving

parts on the generator and engine.

1.4.11 ALWAYS turn the engine off before servicing the machine. If the

engine has electric start, disconnect the negative terminal on the

battery before servicing the machine.

1.4.12 ALWAYS keep the fuel lines in good condition and properly connected.

Leaking fuel and fumes are extremely explosive.

WARNING

Safety Information GP/GPS 6600A

12

1.5 Label Locations

GND

88897

GP/GPS 6600A Safety Information

13

1.6 Safety and Operating Labels

Wacker Neuson machines use international pictorial labels where

needed. These labels are described below:

Label Meaning

WARNING!

Hot surface!

CAUTION

Lifting point.

Electrical ground

Press circuit breaker switch to OFF position.

Check the fuel level.

GND

88897

Safety Information GP/GPS 6600A

14

Open the fuel flow valve.

Press engine switch to ON position.

GPS - Press ignition switch.

GP - Pull the rewind starter.

Press circuit breaker switch to ON position.

Press engine switch to OFF position.

Close the fuel flow valve.

Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains car-

bon monoxide. This is a poison you cannot see or smell.

NEVER use inside a home or garage, EVEN

IF doors and windows are open.

Label Meaning

GP/GPS 6600A Safety Information

15

Only use OUTSIDE and far away from win-

dows, doors, and vents.

WARNING!

To reduce the risk of electrical shock and arc

flash, read the Operator’s Manual. Improper

connection of the generator to a building’s

electrical system can allow electrical current

from the generator to backfeed into utility lines.

This may result in electrocution of utility work-

ers, fire, or explosion. Connections to a build-

ing’s electrical system must be made by a

qualified electrician and comply with all appli-

cable laws and electrical codes.

A nameplate listing the model number, item

number, revision number, and serial number is

attached to each unit. Please record the infor-

mation found on this plate so it will be avail-

able should the nameplate become lost or

damaged. When ordering parts or requesting

service information, you will always be asked

to specify the model number, item number,

revision number, and serial number of the unit.

This equipment does not meet California EVP

emission regulations for small off-road

engines.

This machine may be covered by one or more

patents.

Label Meaning

Safety Information GP/GPS 6600A

16

DANGER!

No sparks, flames or burning objects near

machine.

Shut off the engine before refueling.

Read the Operator’s Manual for machine infor-

mation.

GFCI TEST INSTRUCTIONS - TEST BEFORE EACH USE

Normal operating state - sensing device green LED is "ON" and circuit breaker is at "ON"

position.

Step 1: Press "TEST" button. Green LED should go "OUT" and red LED should come

"ON" and circuit breaker should trigger to "OFF" position.

Step 2: If sensing device LED or breaker does not trip or change state, "DO NOT USE".

Consult an electrician for assistance.

Step 3: Press "RESET" button. Red LED should turn "OFF" and green LED should turn

"ON".

Step 4: Manually reset (switch) circuit breaker to "ON" position to restore circuit power.

Label Meaning

GP/GPS 6600A Operation

17

2. Operation

2.1 Determining Power Requirements

This generator is designed to operate single-phase, 60 Hz appliances

running at 120 VAC or 240 VAC. Check the nameplate or label

provided on tools and appliances to make sure their power

requirements match the power output of the generator.

Some appliances and tools require a surge of current when starting.

This means that the amount of power needed to initially start the

equipment is larger than the power required to keep it running. The

generator must be capable of supplying this “surge” current. Other

types of appliances require more power than is actually stated on their

nameplate.

The information in “Approximate Starting Power Requirements” is

offered only as a general guideline to help you in determining power

requirements for different types of equipment. Check with your nearest

Wacker Neuson dealer, or contact the manufacturer or dealer of the

tool or appliance, with questions regarding its power requirements.

NOTICE: If a tool or appliance does not reach full speed within a few

seconds when switched on, turn it off immediately to avoid damage.

Approximate Starting Power Requirements

• Incandescent lights and appliances such as irons and hot plates, which

use a resistive-type heating element, require the same wattage to start

and run as is stated on their nameplates.

• Fluorescent and mercury lamps require 1.2–2 times their stated

wattage to start.

• Electrical motors and many types of electrical tools often require a

large starting current. The amount of starting current depends on the

type of motor and its use.

• Most electrical tools require 1.2–3 times their stated wattage for

starting.

• Loads such as submersible pumps and air compressors require a very

large force to start. They need as much as 3–5 times the wattage

stated on the nameplate in order to start.

If the wattage is not given for a particular tool or appliance, it can be

calculated by multiplying its voltage and amperage requirements:

Single Phase: VOLTS x AMPS = WATTS

Operation GP/GPS 6600A

18

2.2 Installation

Place the generator in an area where it will not be exposed to rain,

snow, or direct sunlight. Make sure it is positioned on firm, level

ground, so it will not slide or shift. Position the engine exhaust away

from areas where people may be present.

The surrounding area must be free from water and moisture. All

components must be protected from excessive moisture.

Using a generator indoors CAN KILL YOU IN MINUTES. Generator

exhaust contains carbon monoxide. This is a poison you cannot see or

smell. NEVER use this generator inside a home or garage, EVEN IF

doors and windows are open. Only use this generator OUTSIDE and

far away from windows, doors, and vents.

NEVER install a generator in an enclosed area such as a tunnel or a

trench. Using a generator in a tunnel or a trench CAN KILL YOU IN

MINUTES. Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell. NEVER use this generator inside a

tunnel or a trench.

2.3 Recommended Battery (GPS only)

This generator is shipped without a battery. The recommended battery

to be used is:

Battery Type 50-N18L-A

Voltage 12 V

Capacity 20 A/h

L x W x H 206 x 90 x 164 mm

(8-1/8 x 3-9/16 x 6-7/16 in.)

DANGER

DANGERDANGER

GP/GPS 6600A Operation

19

2.4 Battery Installation (GPS only)

2.4.1 Align the holes found in the battery tray (a) to the holes on the frame

cross-member

2.4.2 Insert M8 x 14 screws (b) through the tray then through the holes of

the cross-member.

2.4.3 Insert the nuts (c) onto the screws and tighten. Torque nuts to 18.75

Nm. (13.5 ft.lbs).

2.4.4 Align the holes in the battery tube (d) to the holes in front of the battery

tray.

2.4.5 Insert M8 x 35 screws (e) through the battery tray then through the

tube.

2.4.6 Insert the nuts (f) onto the screws and tighten. Torque nuts to 18.75

Nm. (13.5 ft.lbs).

2.4.7 Insert the tube clamps (g) onto the upper frame tube and align the

holes to the holes of the battery tube.

2.4.8 Insert M8 x 35 screws (h) through the battery tube then through the

tube clamps.

2.4.9 Insert the nuts (j) onto the bolts and tighten. Torque nuts to 18.75 Nm.

(13.5 ft.lbs).

2.4.10 Slide the J-bolt (k) through the holes found in the battery holder (l).

2.4.11 Insert the rounded end of the J-bolt (k) into the slot of the battery tray

and insert the tip of the J-bolt through the hole.

Operation GP/GPS 6600A

20

2.5 Wheel Kit

The wheel kit (Part No. 0161308) is a standard item on Item Number

0620012, 0620015, 0620043 and 0620046 only. It is available as an

option on all other models.

2.5.1 Hoist the generator, and align the axle (c) with the lower cross-member

of frame.

2.5.2 Insert the axle brackets (k) over the axle and align the holes found in

the axle bracket to the holes of the cross-member. Ensure that the

brackets extend under the tube of the frame.

2.5.3 Insert M6 x 16 screws (l) through the outer holes on the cross-member,

then through the holes of the axle bracket.

2.5.4 Insert M6 nuts (m) onto the screws and tighten. Torque to 7.5 Nm (5.25

ft.lbs.).

2.5.5 Assemble the washers (g) next to the rings (h), then add the wheels

(d).

2.5.6 Add the washers (g) next to the wheels, then insert the pins (f) into the

holes of the axle and separate the legs of the pins.

2.5.7 Align the holes found in the leg bracket (b) to the holes of the lower

cross-member.

2.5.8 Insert M6 x 16 screws (l) through the outer holes on the cross-member,

then through the holes of the leg bracket.

2.5.9 Insert M6 nuts (n) onto the screws and tighten. Torque to 7.5 Nm (5.25

ft.lbs.).

2.5.10 Insert M8 x 30 screw (o) through the hole in the leg bracket and

through the hole in cross-member.

2.5.11 Insert M8 nut (p) onto the screw and tighten. Torque to 18.75 Nm (13.5

ft.lbs.).

2.5.12 Align the holes in the rubber foot mounts (e) to the holes of the leg

bracket.

2.5.13 Insert M6 x 20 screws (m) through the leg bracket, then through the

holes of the rubber foot mounts.

2.5.14 Insert the nuts (n) onto the screws and tighten. Torque to 7.5 Nm (5.25

ft.lbs.).

2.5.15 Align the holes found in the handles (a, j) to the holes of the brackets

(1) on the frame.

2.5.16 Insert M6 x 16 screws (l) through the handles, then through the

brackets on the frame.

2.5.17 Insert nuts (m) onto the screws and tighten. Torque to 7.5 Nm (5.25

ft.lbs.).

La page charge ...

Wacker Neuson GP6600 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson GP6600 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents