CLIPSO
®
ESSENTIAL
Pressure cooker
Autocuiseur
EN
FR
User Manual
Guide d’utilisation
www.t-fal.ca
www.t-fal.com
*depending on model - *selon le modèle
F
A
C
E
C
O
T
E
C
O
U
V
E
R
C
L
E
fig. 2fig. 1
fig. 5 fig. 6 fig. 8
fig. 9
fig. 14
fig. 15 fig. 16
fig. 17 fig. 18 fig. 19 fig. 20
fig. 7*
fig. 11
fig. 10 fig. 12
fig. 13
mini
fig. 3 fig. 4
EN
IMPORTANT SAFEGUARDS
For your safety, this device complies with the applicable standards and regulations:
- Pressure vessel appliance
- Materials in contact with food
- Environment
• This product has been designed for domestic use only.
• Any commercial use, inappropriate use or failure to comply with the instructions, the
manufacturer accepts no responsibility and the guarantee will not apply.
• Take time to read all of the instructions and always refer back to the “User's Guide”.
• As with any cooking appliance, ensure close supervision if you are using the pressure cooker with
children nearby.
• Do not put your pressure cooker into a hot oven.
• When the pressure cooker is under pressure, take great care when moving it. Do not touch the
hot surfaces. Use the handles and knobs. Wear gloves if necessary.
• Regularly check that the pan handles are fixed properly. Tighten if necessary.
• Do not use your pressure cooker for any purpose other than that for which it is designed.
• Your pressure cooker cooks under pressure. Burns could result from boiling over if not used
properly. Make sure that the pressure cooker is properly closed before bringing it up to pressure.
Refer to section “Closing”.
• Always make sure that the valve is in the decompression position before opening your
pressure cooker.
• Never force the pressure cooker open. Make sure that the internal pressure has returned to normal.
Refer to section “Safety”.
• Never use your pressure cooker without liquid: this could cause serious damage. Always make
sure that there is enough liquid in it during cooking.
• Use heat source(s) that are compatible with your pressure cooker, in line with the
instructions for use.
• Never make milk-based recipes (such as rice pudding, semolina pudding ...) in your pressure cooker.
• Do not use rock salt in your pressure cooker, but rather add table salt when the cooking is nearly
finished.
• Never fill your pressure cooker more than two-thirds full (maximum fill mark).
• For food that expands during cooking, like rice or dried vegetables or stewed fruit, etc., never fill your
pressure cooker more than half full. For certain soups like pumpkin or courgette, give your pressure
cooker a few minutes to cool down, then cool it down fully by placing it under cold running water.
• After cooking meat which has an outer layer of skin (such as ox tongue), which could swell due
to the effects of pressure, do not pierce the skin after cooking if it appears swollen: you could get
burnt. Pierce it before cooking.
• When cooking food with a thick texture (chick peas, rhubarb, stewed fruit, etc.) the pressure cooker
should be shaken slightly before opening to ensure that the food does not spurt out.
• Always check that valves are clear before use. Refer to section “Before cooking”.
• Do not use the pressure cooker to fry under pressure using oil.
• Do not interfere with the safety systems, except for cleaning and maintenance in accordance
with instructions.
• Use only original T-FAL spare parts suitable for your model. Particularly, use a T-FAL pan and lid.
• Alcohol vapours are flammable. Bring to a boil for about 2 minutes before placing the lid. Watch
your appliance when preparing alcohol-based recipes.
• Do not use your pressure cooker to store acidic or salty food before and after cooking to avoid
damaging your pan.
• You can use the pan to cook food without the lid. Do not use the lid if you do not intend the food
to be cooked under pressure.
KEEP THESE INSTRUCTIONS
1
Specifications
Pressure cooker base diameter - references
Technical information:
Maximum operating pressure: 55 kPa:(8 psi)
Maximum safety pressure: 110 kPa:(16 psi)
Compatible heat sources
• Your pressure cooker can be used on all heat
sources including induction except Aga type
cookers.
• Your pressure cooker can be used on all heat
sources except Aga hobs but including induction.
• On a solid hotplate, use a plate with a
diameter equal to or less than that of the
pressure cooker base.
Capacity
Ø Pan
diameter
Ø Base
diameter
CLIPSO
ESSENTIAL
Pan and lid
material
6 L 24 cm 18 cm P44247
Stainless steel7,5 L 24 cm 18 cm P43948
9 L 24 cm 18 cm P44249
Never heat your pan
when empty, as you
risk damaging your
product.
GAS SOLID
HOTPLATE
GLASS CERAMIC
RADIANT HALOGEN
INDUCTION
ELECTRIC
COIL
Descriptive diagram
A. Operating valve
B. Valve positioning mark
C. Steam release outlet
D. Lid opening/closing button
E. Pressure indicator
F. Safety valve
G. Seal
H. Steam basket*
I. Trivet*
J. Maximum fill mark
K. Pan
L. Pan handle*
*depending on model
EN
2
•On ceramic and halogen hobs, make sure that
the base of the pan is clean and dry.
• On gas, the flame should not extend beyond
the diameter of the pan.
For all heat sources, make sure that your
pressure cooker is well centered.
T-FAL Accessories
• The following Clipso pressure cooker accessories are
available. Contact the helpline - see contact list.
-
• To replace parts or for repairs, contact the
helpline - see contact list.
• Use only original T-FAL parts suitable for your
model.
Use
Opening
• Press the opening button (D) on the lid - fig. 1.
• Lift the lid keeping the button pressed down - fig. 2.
Closing
• Press the opening/closing button (D) on the
lid and place it on the pan - fig. 3.
• Apply a little force on the top of the lid before
releasing the button (D) to trigger the locking
mechanism.
• Release the opening/closing button (D) on the
lid and ensure that the jaws are properly
locked under the rim of the pan (K) - fig. 4.
Accessories Reference number
Gasket
6L - 7,5L - 9L
X1010006
Steam basket*
6L - 7,5L - 9L
792654
Trivet*
792691
*depending on model
EN
3
Minimum and maximum filling
• Minimum 250 ml (2 glasses) - fig. 5.
• Maximum 2/3
rd
of the depth of the pan (J) - fig. 6.
For some foods:
• For foodstuffs that expand during cooking, like rice
or soups or dried vegetables or stewed fruit, etc.,
do not fill your pressure cooker more than half full.
For soups, we recommend you carry out a fast
pressure release (refer to section "End of cooking").
Using the steam basket*
• Pour 750 ml of water into the base of the
pan (K).
• Place the trivet* (I) in the base of the pan.
• Place the basket* (H) on the trivet* - fig. 7.
Using the operating valve
• Place the valve (A) on the steam release outlet (C)
aligning the two symbols .
• Press the valve down fully - fig. 8 and turn until it
stops at - fig. 9.
To cook food:
• Turn the valve positioning mark until it stops
at .
To remove the operating valve (when it is no
longer pressurised):
• Press down on the operating valve (A) and align
the two symbols - fig. 10.
• Remove it - fig. 11.
Food placed in the
steam basket* must
not touch the pressure
cooker lid.
*depending on model
EN
4
First use
• Place the trivet* (I) in the base of the pan.
• Fill the pressure cooker up to 2/3rd full with water (J)
- fig. 6.
• Place the steam basket* (H) on the trivet* (I) - fig. 7.
• Close the pressure cooker.
• Fit the operating valve (A) and turn until it
stops at - fig. 9.
• Place the pressure cooker on a heat source set to
maximum power.
• When steam starts escaping through the valve,
reduce the heat source and set a timer for 20 minutes.
• After 20 minutes, turn off the heat.
• Gradually turn the valve positioning mark
until it stops at adjusting the speed at which
you want to release the pressure.
• When the pressure indicator (E) drops, your pressure
cooker is no longer under pressure.
• Open the pressure cooker - fig. 1 - 2 and rinse it.
Note: the appearance of stains on the inside of the
pan does not alter the quality of the metal in any
way. They are simply scale deposits. To remove the
deposits, you can use a sponge pad with a little
diluted white vinegar.
Before cooking
• Every time you use your cooker, first visually check
in good daylight that the steam release outlet
(C) is not blocked - fig. 12.
• Also check that the safety valve (F) moves freely
- (refer to section “Cleaning and maintenance”).
• Fill the pressure cooker with the food and the
necessary amount of liquid for cooking (see Minimum
and Maximum filling' section..
• Close the pressure cooker - fig. 3 - 4.
• Fit the operating valve (A) - fig. 8.
• Press the valve down fully and turn until it stops at
- fig. 9.
• Make sure that the pressure cooker is properly
closed before bringing it up to pressure.
• Place the pressure cooker on a heat source set to
maximum power.
*depending on model
Position your
pressure cooker so
that the steam is
released away from
you.
EN
5
During cooking
• When steam escapes through the operating
valve continuously, and a regular hissing
sound (PSCHHHT) is heard, reduce the heat
source.
• Set a timer for the cooking time stated in your
recipe.
• During cooking, check that the valve murmurs
regularly. If there is not enough steam,
increase the heat source slightly; if there is too
much steam, reduce the heat source.
End of cooking
To release the steam:
• After the heat has been turned off you have two
alternatives:
- Slow pressure release:
• Gradually turn the operating valve (A) adjusting
the speed at which you want to release the
pressure until it stops at . Make sure that the
cooker is positioned so that the steam is directed
away from you.
• When the pressure indicator (E) drops again,
your pressure cooker is no longer under pressure.
This method is used for stews, vegetables, meat
joints and fish dishes. If you notice any food or
liquid start to spray out from the valve when you
are releasing steam, set the selector to cooking
position then wait a minute and then
gradually turn the operating valve again, making
sure that nothing else spurts out.
- Fast pressure release:
• Place your pressure cooker in a sink under cold
running water, directing the flow onto the metal
part of the lid - fig. 13.
• When the pressure indicator (E) drops again,
your pressure cooker is no longer under pressure.
The pressure indicator
(E) prevents you from
opening the pressure
cooker if it still under
pressure.
If the pressure indicator
(E) does not drop, place
the base of your
pressure cooker into a
sink filled with cold
water - fig. 13.
Never interfere with the
pressure indicator.
The pressure indicator
(E) prevents the pressure
cooker from increasing
in pressure if it is not
properly closed.
As with any cooking ap-
pliance, watch over it
carefully especially if you
are using your pressure
cooker around children.
Steam is very hot as it
exits the steam release
outlet.
If food or liquid starts
to spray out while you
are releasing the steam,
return the operating
valve (A) to cooking po-
sition then release
the steam using the
fast pressure release
method described
opposite.
EN
6
Turn off the water and then, turn the positioning mark
of the operating valve (A) until it stops at .
• You can open the pressure cooker - fig. 1 - 2.
This method is used for soups, rice, pasta, cake and
pudding mixes, recipes containing rice or pasta and recipes
with a high liquid content.
If in doubt about which method of pressure release is
correct, use the fast pressure release method.
• When cooking frothy or starchy foods, do not release the
pressure by turning the operating valve (A). Instead lift the
pressure cooker away from the heat source, leave the
operating valve (A) in the cooking position and let the
cooker cool slowly at room temperature (takes about 15
minutes) until the pressure indicator drops down. Reduce
the recommended cooking time a little.
• You can open the pressure cooker - fig. 1 - 2.
Cleaning and maintenance
Cleaning the pressure cooker
To ensure the correct operation of your pressure
cooker, follow these cleaning and maintenance
recommendations after each use.
• Wash the pressure cooker (pan and lid) after
each use using warm water with soap. Follow
the same procedure for the basket*.
• Never use bleach or products containing chlorine.
• Do not overheat your pan when empty.
To clean the inside of the pan:
• Wash with a sponge pad and soap.
• If the interior of the steel pan has an iridescent
sheen, clean it using white vinegar or a special
stainless steel cleaning product.
To clean the outside of the pan:
• Wash using a sponge and soap. Clean it with a
special stainless steel cleaning product.
*depending on model
Regularly check that
the pan handles are
attached properly.
Tighten them again
if necessary.
The browning and
marks which may
appear following
long term use do not
affect the operation
of the pressure
cooker.
For a longer
pressure cooker life,
do not overheat
your pressure
cooker pan when it
is empty.
EN
7
To clean the lid:
• Wash the lid using a sponge and soap.
To clean the lid seal:
• After each use, clean the seal (G) and its groove
using a sponge, warm water, and soap.
• To refit the seal, refer to - fig. 13 - 14. Ensure that
the words “face côté couvercle” [facing lid side] are
against the lid.
• Replace the pressure cooker seal every year or if it
shows signs of splitting or damage.
To clean the operating valve (A) :
• Remove the operating valve (A) - fig. 10 -11.
• Wash the operating valve (A) under running tap
water - fig. 15.
• Check that it moves freely: see drawing on the
right.
To clean the steam release (C) outlet on the lid:
• Remove the valve (A) - fig. 10 - 11.
• Check visually and in plain daylight that the steam
release outlet (C) is clear and round - fig. 12. If
necessary, clean with a toothpick - fig. 16 and rinse.
To clean the safety valve (F):
• Clean the part of the safety valve located inside
the lid by placing it under running water.
• Check its correct operation by pressing hard, using
a cotton bud, on the pin, which should move freely
- fig. 17.
To change the seal of your pressure cooker:
• Change the seal of your pressure cooker every
year or if it has any splits or is damaged.
• Always use an original T-FAL seal suitable for
your model.
If the safety valve ac-
cidentally comes out
of its housing partly
or fully, this may
cause a leak without
any danger.
Contact the helpline -
see contact list.
For a longer pressure
cooker life, do not
overheat your
pressure cooker pan
when it is empty.
Never put the seal
in the dishwasher.
You can wash the
pan and the lid in
the dishwasher
after you have
removed the seal
and the operating
valve.
EN
8
To store your pressure cooker:
• Turn the lid over on the pan - fig. 18.
Safety
Your pressure cooker is fitted with several safety
devices:
• Closing safety:
- The jaws must be in contact with the rim of the lid.
If this is not the case, there is steam leakage from
the pressure indicator and the pressure cooker will
not build up pressure.
• Opening safety:
- If the pressure cooker is under pressure, the
opening button cannot be pressed.
- Never try to force the pressure cooker open.
- Above all do not interfere with the pressure
indicator.
- Make sure that the internal pressure has fallen
before opening.
• Two safety devices operate to prevent
overpressure:
- First device: the safety valve (F) releases the
pressure and steam escapes - fig. 19.
- Second device: the seal allows steam to escape
from between the lid and the pan - fig. 20.
If one of the overpressure safety systems is
triggered:
• Turn off the heat source.
• Let the pressure cooker cool down completely.
• Open it (refer to section “Opening”).
• Check and clean the operating valve (A), the
steam release outlet (C), the safety valve (F) and
the seal (G).
• If, after these checks and cleaning, your product
leaks or no longer works, take it to a T-FAL
Approved Service Centre. Contact the Customer
Relations Helpline - see contact list.
The pressure
indicator (E)
prevents the lid from
opening if it still
under pressure.
The pressure
indicator (E)
prevents pressure
from building if it is
already under
pressure.
You must have your
pressure cooker checked
in a T-FAL Approved
Service Centre after 10
years of use.
EN
9
Recommendations for use
1 - Steam is very hot when it leaves the operating
valve.
2 - As soon as the pressure indicator rises, you can
no longer open your pressure cooker.
3 - As with any cooking utensil, ensure close
supervision if you are using the pressure
cooker near children.
4 - Watch out for the jet of steam.
5 - To move the pressure cooker, use the two pan
handles.
6 - Never leave food in your pressure cooker.
7 - Never use bleach or products containing
chlorine, as these will alter the quality of the
stainless steel.
8 - Do not leave the lid soaking in water.
9 - Change the seal every year or if it has any
splits or is damaged.
10 - You must only clean your pressure cooker
when it is cold and empty.
11 - It is essential to have your pressure cooker
checked in a T-FAL Approved Service Centre
after 10 years of use. Contact the Customer
Relations Helpline - see contact list.
Guarantee
• T-FAL pressure cookers have a 10 year guarantee from the date
of purchase against any faulty materials or workmanship
related to the pot or any premature damage of the metal base
provided the product is used in accordance with the
manufacturer's recommended product instructions. This
guarantee does not include any damage due to inappropriate
use or resulting from knocks, falls or by placing the product in
the oven.
• It should be noted that the normal life of the gasket, pressure
control, valves, handles or locking indicator seal is limited.
These parts are excluded from the guarantee and will require
periodic renewal. It should also be noted that for models with
an electronic timer, the timer is guaranteed for the first year
only. Accessories such as the basket, trivet and steam basket
are also guaranteed for 12 months only.
EN
10
T-FAL answers your questions
Regulatory markings
Problems Recommendations
If you are unable
to close the lid:
Press the opening/closing button (D) on the
lid and place it on the pan - fig. 3.
Apply a little force on the top of the lid before releasing
the button (D) to trigger the locking mechanism.
Release the opening/closing button (D) on the lid
and ensure that the jaws are properly
locked under the rim of the pan (K) - fig. 4
If your pressure
cooker has been
heated under pres-
sure without any
liquid in it:
Have your pressure cooker checked by a T-FAL Appro-
ved Service Centre. Contact the Customer Relations
Helpline - see contact list.
If the pressure in-
dicator has not
risen and nothing
is escaping
through the valve
during cooking:
This is normal during the first few minutes.
If this problem persists, check that:
- The heat source is sufficiently high; if not, increase it.
- The quantity of liquid in the pan is sufficient.
- The operating valve is on
.
- The pressure cooker is properly closed.
- The seal or the edge of the pan is not damaged.
- The seal is correctly positioned in the lid, (refer to
section “Cleaning and Maintenance”)
Marking Location
Identification of manufacturer or commercial
brand
On the lid
Production year and batch Inside of the lid
Capacity
Model reference
Maximum safety pressure (PS)
Maximum operating pressure (PF)
On the exterior base
of the pan
EN
11
Problems
Recommendations
If the pressure
indicator has risen and
nothing is
escaping through the
valve during cooking:
This is normal during the first few minutes.
If the problem persists, place your pressure cooker
in a sink under cold running water from a tap until
the pressure indicator drops - fig. 13.
Clean the operating valve (A) - fig. 15 and the
steam release outlet (C) - fig. 16 and check that
the safety valve pin drops without difficulty - fig. 17.
If steam leaks from
around the lid, check:
The correct closure of the lid.
The position of the lid seal.
The seal is correctly fitted in the lid.
The cleanliness of the lid, the seal and its groove
in the lid.
The rim of the pan is in good condition and not
damaged.
If you are unable to
open the lid:
Check that the pressure indicator is in the lowered
position.
Otherwise, place your pressure cooker in a sink under
cold running water from a tap until the pressure
indicator drops - fig. 13.
Never interfere with the pressure indicator.
If the food is not
cooked or is burned,
check:
The cooking time.
The power of the heat source.
The correct position of the operating valve.
The quantity of liquid.
If food has burned in
the pressure cooker:
Leave the pan to soak before cleaning it.
Never use bleach or products containing chlorine.
If one of the
overpressure safety
systems is triggered:
Turn off the heat source.
Let the pressure cooker cool down without moving it.
Wait for the pressure indicator to drop and open
the pressure cooker. (refer to section “Opening ”).
Check and clean the operating valve, the steam
outlet, the safety valve and the seal.
If the problem persists, contact the Customer
Relations Helpline - see contact list.
EN
• Environment protection first !
i Your appliance contains valuable materials which can be
recovered or recycled.
‹ Leave it at a local civic waste collection point.
12
Précautions importantes
Pour votre sécurité, cet appareil est conforme aux normes et réglementations applicables :
- appareils sous pression
- matériaux en contact avec les aliments
- environnement
• Cet appareil a été conçu pour un usage domestique.
• Pour toute utilisation commerciale ou inadéquate ou tout non-respect des
instructions, le fabricant déclinera la responsabilité et la garantie sera non valide.
• Prenez le temps de lire toutes les instructions et reportez-vous toujours au «Guide de
l’utilisateur».
• Comme pour tout appareil de cuisson, assurez une étroite surveillance surtout si vous
utilisez l’autocuiseur à proximité d’enfants.
• Ne mettez pas votre autocuiseur dans un four chaud.
• Déplacez votre autocuiseur sous pression avec un maximum de précautions. Ne
touchez pas les surfaces chaudes. Utilisez les poignées et boutons. Utilisez des gants,
au besoin.
• Vérifiez régulièrement les poignées de la cuve afin de vous assurer qu'elles sont
correctement fixées. Revissez-les au besoin.
• N’utilisez pas votre autocuiseur dans un autre but que celui auquel il est destiné.
• Votre autocuiseur cuit sous pression. Des blessures par ébouillantage peuvent résulter
d’une utilisation inadéquate. Assurez-vous que l’autocuiseur est convenablement
fermé avant de le mettre en service. Voir paragraphe «Fermeture » .
• Assurez-vous que la soupape est en position de décompression (
) avant d’ouvrir
votre autocuiseur.
• N’ouvrez jamais l’autocuiseur en force. Assurez-vous que la pression intérieure est
retombée. Voir paragraphe «Sécurité».
• N’utilisez jamais votre autocuiseur sans liquide, cela le détériorerait gravement.
Assurez-vous qu’il y a toujours suffisamment de liquide pendant la cuisson.
• Utilisez la(les) source(s) de chaleur compatible(s), conformément aux instructions
d’utilisation.
• Ne préparez jamais de recette à base de lait dans votre autocuiseur.
• N’utilisez pas de gros sel dans votre autocuiseur, ajoutez du sel fin en fin de cuisson.
• Ne remplissez pas votre autocuiseur au-delà des 2/3 (repère maximum de
remplissage).
• Pour les aliments qui se dilatent pendant la cuisson, comme le riz, les légumes
déshydratés, ou les compotes, ... ne remplissez pas votre autocuiseur au-delà de la
moitié de sa capacité. Pour certaines soupes à base de potirons, courgettes, …laissez
refroidir votre autocuiseur quelques minutes, puis effectuez un refroidissement sous
eau froide.
• Après cuisson de viandes qui comportent une peau superficielle (ex. langue de
bœuf…), qui risque de gonfler sous l’effet de la pression, ne piquez pas la viande
tant que la peau présente un aspect gonflé ; vous risqueriez d’être ébouillanté. Veillez
à piquer la viande avant la cuisson.
• Dans le cas d’aliments pâteux (pois cassés, rhubarbe…), l’autocuiseur doit être
légèrement secoué avant l'ouverture pour que ces aliments ne giclent pas à l’extérieur.
• Assurez-vous que les soupapes ne sont pas obstruées avant chaque utilisation. Voir
paragraphe «Avant la cuisson».
• N’utilisez pas votre autocuiseur pour faire frire des aliments sous pression avec de
l’huile.
• N'interférez pas avec les systèmes de sécurité au-delà des consignes de nettoyage
et d’entretien.
• N’utilisez que des pièces d’origine T-FAL correspondant à votre modèle. En particulier,
utilisez une cuve et un couvercle T-FAL.
• Les vapeurs d’alcool sont inflammables. Portez à ébullition environ 2 minutes avant
de mettre le couvercle. Surveillez votre appareil lorsque vous préparez des recettes à
base d’alcool.
• N’utilisez pas votre autocuiseur pour stocker des aliments acides ou salés avant et
après la cuisson au risque de dégrader votre cuve.
CONSERVEZ CES INSTRUCTIONS
FR
13
Caractéristiques
Diamètre du fond de l’autocuiseur - références
Informations normatives :
Pression maximum de fonctionnement : 55 kPa
Pression maximum de sécurité : 110 kPa
Sources de chaleur compatibles
• L’autocuiseur s’utilise sur toutes les sources de
chaleur, y compris à induction et excepté les
cuisinières AGA.
• Sur plaque électrique, employez une plaque de
diamètre égal ou inférieur à celui du fond de
l’autocuiseur.
Capacité Ø Cuve Ø Fond
CLIPSO
ESSENTIAL
Matériau cuve
et couvercle
6 L 24 cm 18 cm P44247
Inox7,5 L 24 cm 18 cm P43948
9 L 24 cm 18 cm P44249
Ne faites pas
chauffer votre cuve
lorsqu’elle est vide,
au risque de
détériorer votre
produit.
GAZ PLAQUE
ÉLECTRIQUE
VITROCERAM
HALOGENE
RADIANT
INDUCTION
SPIRALE
ÉLECTRIQUE
Schéma descriptif
A. Soupape de fonctionnement
B. Repère de positionnement de la
soupape
C. Conduit d’évacuation de vapeur
D. Bouton d’ouverture/fermeture
E. Indicateur de présence de pression
F. Soupape de sécurité
G. Joint
H. Panier vapeur*
I. Trépied*
J. Repère maximum de remplissage
K. Cuve
L. Poignée de cuve*
*selon le modèle
FR
14
• Sur une surface vitrocéramique, assurez-vous que le
fond de la cuve est propre et net.
• Sur gaz, la flamme ne doit pas déborder du
diamètre de la cuve.
Sur toutes les sources de chaleur, veillez à ce que
votre autocuiseur soit bien centré.
Accessoires T-FAL
• Les accessoires de votre autocuiseur disponibles
en magasins. Composez le numéro du service
d'assistance pour connaître la liste de contacts.
-
• Pour remplacer des pièces ou pour des
réparations,adressez-vous au service
d'assistance - voir la liste.
• N’utilisez que des pièces d’origine T-FAL
correspondant à votre modèle.
Utilisation
Ouverture
• Appuyez sur le bouton d’ouverture/fermeture (D)
- fig. 1.
•Soulevez le couvercle en maintenant le bouton
enfoncé - fig. 2.
Fermeture
• Appuyez sur le bouton d'ouverture/fermeture
(D) du couvercle et posez ce dernier sur la cuve
- fig. 3.
• Appliquez une légère pression sur le dessus du
couvercle avant de relâcher le bouton (D) pour
déclencher le mécanisme de verrouillage.
• Relâchez le bouton d'ouverture/fermeture (D)
du couvercle et veillez à ce que les mâchoires
se referment bien sous le rebord de la cuve (K)
- fig. 4.
Accessoires Référence
Joint
6L - 7,5L - 9L
X1010006
Panier vapeur*
6L - 7,5L - 9L
792654
Trépied*
792691
*selon le modèle
FR
15
Remplissages minimum
et maximum
• Minimum 250 ml (2 verres) - fig. 5.
• Maximum 2/3 de la hauteur de la cuve, marquage (J)
- fig. 6.
Pour certains aliments :
• Pour les aliments qui se dilatent pendant la
cuisson, comme le riz, les soupes, les légumes
déshydratés ou les compotes, … ne remplissez pas
votre autocuiseur au-delà de la moitié de la
hauteur de la cuve. Pour ce qui est des soupes,
nous vous conseillons d'effectuer une
décompression rapide (voir paragraphe «Fin de
cuisson»).
Utilisation du panier vapeur*
• Versez 750 ml d’eau dans le fond de la cuve (K).
• Posez le trépied* (I) au fond de la cuve.
• Mettez le panier* (H) sur le trépied* - fig. 7.
Utilisation de la soupape de
fonctionnement
• Posez la soupape (A) sur le conduit d’évacuation de
vapeur (C) en alignant les deux pictogrammes .
• Appuyez à fond - fig. 8 et tournez jusqu'à la butée
du pictogramme - fig. 9.
Pour faire cuire les aliments :
• Positionnez le repère de positionnement de la
soupape jusqu'à la butée du pictogramme .
Pour retirer la soupape de fonctionnement :
• Appuyez sur la soupape de fonctionnement (A) et
alignez les deux pictogrammes - fig. 10.
• Retirez-la - fig. 11.
Les aliments dans le
panier vapeur* ne
doivent pas toucher le
couvercle de
l’autocuiseur.
*selon le modèle
FR
16
Première utilisation
• Posez le trépied* (I) au fond de la cuve.
• Remplissez la cuve (K) d'eau jusqu'aux 2/3 (J) -
fig. 6.
• Mettez le panier* (H) sur le trépied* (I) - fig. 7.
• Fermez l’autocuiseur.
• Placez la soupape de fonctionnement (A) et
positionnez-la en butée sur - fig. 9.
• Posez l’autocuiseur sur une source de chaleur
réglée à sa puissance maximum.
• Lorsque la vapeur commence à s’échapper par la
soupape, réduisez la source de chaleur et réglez
une minuterie à 20 min.
• Lorsque les 20 min. sont écoulées, éteignez votre
source de chaleur.
• Tournez progressivement le repère de
positionnement de la soupape en butée face
au pictogramme en choisissant à votre
convenance la vitesse de décompression.
• Lorsque l’indicateur de présence de pression (E)
redescend, votre autocuiseur n’est plus sous pression.
• Ouvrez l’autocuiseur - fig. 1 - 2 et rincez-le.
Avant la cuisson
• Avant chaque utilisation, vérifiez à l’œil nu et à la
lumière du jour afin de vous assurer que le conduit
d’évacuation de vapeur (C) n’est pas obstrué - fig.
12.
• Assurez-vous que la soupape de sécurité (F) est
mobile (voir le paragraphe «Nettoyage et
entretien»).
• Remplissez votre autocuiseur.
• Fermez votre autocuiseur - fig. 3 - 4.
• Mettez en place la soupape (A) - fig. 8.
• Appuyez à fond et tournez jusqu’à la butée du
pictogramme - fig. 9.
• Assurez-vous que l’autocuiseur est
convenablement fermé avant de le mettre en
service.
• Posez l’autocuiseur sur une source de chaleur puis
réglée à sa puissance maximum.
*selon le modèle
FR
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
Tefal CLIPSO ESSENTIAL Manuel utilisateur
- Catégorie
- Autocuiseurs
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Tefal CLIPSO ESSENTIAL User manual
Documents connexes
-
Tefal P2534443 Manuel utilisateur
-
Tefal P2575034 Manuel utilisateur
-
-
-
T-Fal P4240766 Manuel utilisateur
-
-
-
-
-
